Search NASA⌕ Search

SEARCH · Search NASA

Results for “fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

The use of fused filament fabrication (FFF) acrylonitrile butadiene styrene (ABS) and other thermoplastics in radiation environments is beginning to be studied as possible replacements for traditionally manufactured parts and tools. Interlayer adhesion within the mesostructure has been shown in published literature to be an integral component in the strength of FFF ABS. Research of irradiated 3D printed polymers has primarily focused on the influence of gamma irradiation on the mechanical properties of FFF ABS samples, without evaluating its impact on the mesostructure of the samples. The purpose of this paper is to understand the mechanical damage caused by proton radiation on FFF ABS samples through the evaluation of the mesostructure of the ABS samples. To achieve this objective, proton radiation at 40 MeV was applied to FFF ABS samples at radiation doses up to 1.0 MGy at a dose rate of 1 MGy/hr. Following the irradiation, tensile testing was performed on the samples. Here, the fractured surfaces of the tested samples were subsequently observed using a scanning electron microscope. The mechanical test results show an increase in the ultimate tensile strength (UTS) and a decrease in the ductility of the irradiated samples. Statistical analysis on the results shows that there is a statistically significant difference in the UTS and the ductility of unirradiated and 1.0 MGy irradiated samples and between irradiated samples and 1.0 MGy samples. In addition, the percentage elongation at break has statistically significant differences in the means between irradiated samples and 1.0 MGy samples. The UTS has statistically significant differences in the means between 0.1 MGy and 1.0 MGy. The difference in the means between the unirradiated and the 1.0 MGy samples is the most significant for both the UTS and elongation at break. The scanning electron microscopy (SEM) results indicated that interlayer adhesion improved as a function of radiation dose corresponding to the increase in tensile strength. The SEM results also showed that crazing and plastic deformation were reduced; aligning with the loss in ductility observed in the tensile tests results. The proton radiation is causing these mechanical and physical changes through two mechanisms: (1) dose rate effects on ionizing radiation-induced oxidative degradation; and (2) radiation heating effects of high energy (>1 MeV) charged particles.

electron microscopy↗
DOE OSTI2025

Multimodal Defect Imaging of Pure Tungsten Components Fabricated via Electron Beam Powder Bed Fusion

The utilization of additive manufacturing (AM) techniques for refractory materials in high-temperature environments has significantly expanded because of the ability to fabricate geometrically complex components. Electron beam powder bed fusion (EB-PBF), which provides lower residual stress, a cleaner vacuum environment, and better efficiency for high melting point, is one of the best-suited AM methods to produce advanced refractory components. However, the property variation attributed to the heterogeneous microstructure and process-induced defects has hindered the widespread adoption of EB-PBF-produced material like tungsten. While numerous in-situ monitoring and defect detection methods have been demonstrated for EB-PBF, a workflow that compares and evaluates process-induced abnormalities from different imaging perspectives is still limited. This study examines a feature-embedded tungsten component manufactured via the EB-PBF process to demonstrate the defect detection capabilities of a multimodal defect imaging workflow. The predefined and process-induced defects are evaluated by harnessing various imaging techniques, including in-situ electron imaging, layerwise near-infrared (NIR) imaging, post-build high-energy x-ray computed tomography (CT), and conventional destructive metallography. The results highlight the strengths and limitations of distinctive defect imaging techniques concerning specific defect types, sizes, and conditions. It was found that electron imaging can provide more abnormal detection capabilities while maintaining a higher measuring accuracy, against the conventional metallography in this case study, compared with NIR and CT imaging techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of Mechanical Properties of Parts Fabricated with Gas- and Water-Atomized 304L Stainless Steel Powder in the Laser Powder Bed Fusion Process

In this report the use of gas-atomized powder as the feedstock material for the Laser Powder Bed Fusion (L-PBF) process is common in the Additive Manufacturing (AM) community. Although gas-atomization produces powder with high sphericity, its relatively expensive production cost is a downside for application in AM processes. Water atomization of powder may overcome this limitation due to its low cost relative to the gas-atomization process. In this work, gas- and water-atomized 304L stainless steel powders were morphologically characterized through Scanning Electron Microscopy (SEM). The water-atomized powder had a wider particle size distribution and exhibited less sphericity. Measuring powder flowability using the Revolution Powder Analyzer (RPA) indicated that the water-atomized powder had less flowablility than the gas-atomized powder. Through examining the mechanical properties of L-PBF fabricated parts using tensile tests, the gas-atomized powder had significantly higher yield tensile strength and elongation than the water-atomized powder, however, their ultimate tensile strengths were not significantly different.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Hot-Roll Fabrication of Anisotropic Nanograin Nd-Fe-B Magnet

Nd-Fe-B based magnets have the highest energy product among all permanent magnets, which is required for numerous clean energy technologies. For higher temperature applications (T > 150°C), additions of heavy rare earth elements (HREEs) such as Dy are required to maintain sufficient coercivity during operation. Additions of Dy are expensive. Thus, it is desirable to reduce the need for HREEs by reducing the grain size to the nanoscale, which increases the coercivity and decreases its temperature dependence. Here, we report a novel nanograin Nd-Fe-B magnet fabrication method that is continuous and inexpensive. The process uses mechanically milled Nd-Fe-B melt-spun flakes as feedstock powder that is packed into a metal vessel and then hot rolled to form a fully dense and highly textured strip magnet with tailored thicknesses, down to 800 µm. Finally, using this process, fully dense nanograin bulk magnets can be synthesized in minutes compared to the traditional multi-step processes that are typically low throughput.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Chloride Molten Salt Electrolysis Enables Integrated and Energy-Efficient Process for NdFeB Magnet Fabrication

Rare-earth elements (REEs) have been identified by NATO, the USDOE, and USGS as critical materials, i.e., materials which have significant demand yet pose supply-chain risks. Many of the existing processes for separations, metallization, and final parts production used across the REE supply chain involve energy intensive steps. For example, neodymium (Nd or NdPr) is produced using oxyfluoride electrolysis of Nd 2 O 3 , which requires hydrofluoric acid to produce a key electrolyte component (NdF 3 ) and generates undesired perfluorocarbon (PFC) gases. Such challenges make securing a resilient supply chain for NdFeB permanent magnets in countries like the United States prohibitively difficult. Here, we propose a chloride-based MSE process that circumvents these challenges, delivering high-purity NdPr from a (NdPr)Cl 3 feed from upstream REE separations. This eliminates environmentally-damaging steps of oxalate or carbonate precipitation and calcination, and enables superior production rates due to greater solubility of (NdPr)Cl 3 in chloride melts compared to Nd 2 O 3 . We show that CMSE generates high-purity NdPr (99.4 wt.%) while being energy-efficient (~ 6 kWh/kg-Nd). NdPr from CMSE was used to fabricate a NdFeB magnet with an excellent maximum energy product (> 40 MGOe), comparable to commercially available NdFeB magnets. This establishes CMSE as a leading approach for integrated, energy-efficient NdFeB magnet production.

Materials science↗
DOE OSTI2022

A thermochemical database from high-throughput first-principles calculations and its application to analyzing phase evolution in AM-fabricated IN718

A comprehensive thermochemical database is constructed based on high–throughput first-principles phonon calculations of over 3000 atomic structures in limited concentrations in Ni, Fe, and Co alloys involving a total of 26 elements including Al, B, C, Cr, Cu, Hf, La, Mn, Mo, N, Nb, O, P, Re, Ru, S, Si, Ta, Ti, V, W, Y, and Zr, providing thermochemical data largely unavailable from existing experiments. Here, the database can be employed to predict the equilibrium phase compositions and fractions directly from first-principles by minimizing the chemical potential of a multicomponent system with a fixed overall chemical composition and a fixed temperature. It is applied to the additively manufactured nickel-based IN718 superalloy to analyze the phase evolution with temperature. IN718 is known for its great performance in tensile, fatigue, creep, and rupture strength, combined with easy fabrication and corrosion resistance. In particular, we successfully predicted the formation of L1 0 -FeNi, γ’-Ni 3 (Fe,Al), α-Cr, δ-Ni 3 (Nb,Mo), γ”-Ni 3 Nb, and η-Ni 3 Ti at low temperatures (below 680 K), γ’-Ni 3 Al, δ-Ni 3 Nb, γ”-Ni 3 Nb, α-Cr, and γ-Ni(Fe,Cr,Mo) at intermediate temperatures (between 680 and 1140 K), and δ-Ni 3 Nb and γ-Ni(Fe,Cr,Mo) at high temperatures (above 1140 K) in IN718. These predictions are validated by EDS mapping of compositional distributions and corresponding identifications of phase distributions. The database is expected to be a valuable source for future thermodynamic analysis and microstructure prediction of alloys involving the 26 elements.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Area-based composition predictions of materials fabricated using simultaneous wire-powder-directed energy deposition

Functionally graded materials are an emergent method for designing components with programmable site-specific material properties. These materials are typically fabricated using metal additive manufacturing tools by simultaneously feeding multiple wire and/or powder feedstocks at various rates to achieve spatial composition change. The wire-powder-directed energy deposition (WP-DED) technique is of particular interest for many functionally graded material applications by balancing the low raw materials cost of wire with the high resolution of powder. However, feeding wire and powder are inherently different processes since all extruded wire enters the melt pool, while much of the blown powder is scattered, which makes determining the composition of the build challenging. In this study, we devise a simple area-based measurement method for estimating the composition of WP-DED structures. WP-DED single beads are printed using 309L stainless steel wire and commercially pure Fe powder at five wire feed rates (0.5, 0.75, 1.00, 1.25, 1.50 mm/mm) and five powder feed rates (2, 4, 6, 8, 10 rpm). Characteristic defects including interface gaps and macrosegregation (lack of mixing) tendencies are examined. High powder feed rates (8, 10 rpm) result in interface gaps at all wire feed rates, but smooth deposition and complete mixing is achieved at low powder feed rates, particularly with lower wire feed rates as well. The area-based composition measurement method is within ±20% of energy dispersive x-ray spectroscopy measurements for all samples, showing its effectiveness as a rapid composition estimate for WP-DED materials development.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigating the effect of different shielding gas mixtures on microstructure and mechanical properties of 410 stainless steel fabricated via large scale additive manufacturing

Metal Big Area Additive Manufacturing (mBAAM) offers the potential to fabricate large scale tools at high deposition rates (15 lb/h+). 410 martensitic steel is a potential tooling material, owing to its low cost, good machinability and reasonable printability. During the mBAAM process, the shielding gas can have a significant impact on the material properties as well as the process cost. Therefore, the current study aims to understand the effect of different shielding gas mixtures on large-scale additive manufacturing of 410 martensitic stainless steel. We show that an argon mixture with 3% nitrogen gas produced the best performance in terms of maximum hardness and tensile strength, with much less scatter in tensile strength. He-Ar-CO 2 or tri-mix shielded samples showed a low tensile strength with wide scatter, due to stabilized delta ferrite in microstructure during printing. Both tri-mix and Ar-CO 2 shielded samples showed slightly higher porosity. Thus, we recommend the use of argon-3% nitrogen as a shielding gas mixture for processing 410 steel for tool applications, based on the relatively low cost of this gas mixture and the resulting higher hardness, higher dimensional stability, and lower porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2022

On the efficacy of post-build thermomechanical treatments to improve properties of Zirconium fabricated using ultrasonic additive manufacturing

Here, hot-isostatic pressing has been applied to Zirconium plate fabricated using the ultrasonic additive manufacturing (UAM) technique to enhance interfacial bond quality. Specimens heated to 800 C for 1 h at 100 MPa pressure showed grain growth across many prior foil-to-foil interfaces, thereby increasing foil adhesion. In addition to the material softening induced by a loss of Hall-Petch strengthening, premature failure of specimens loaded parallel to the build direction was observed. Premature specimen failure was attributed to the local delamination at prior foil-to-foil boundaries where grain growth was pinned by Ti impurities introduced during the UAM process via the interaction between a Ti-alloy buffer foil and the welded Zr-foils underneath. In addition, the presence of Ti along select foil interfaces resulted in the nucleation and growth of secondary (Zr,Ti)(Fe,Cr) laves phases during higher-temperature thermomechanical processing. Using a combination of micro-scale X-ray computed tomography, fractography, and in-situ digital image correlation, the effect of defects along prior foil-to-foil boundaries was revealed as delamination-assisted plasticity accelerated specimen failure in preferred tensile orientations. These findings underscore the importance of impurity control when optimizing weld quality of higher-strength material systems using ultrasonic welding.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hypereutectic Al-Ce-X (X=Mn, Cr, V, Mo, W) alloys fabricated by laser powder-bed fusion

Here, we characterize the microstructures and high-temperature mechanical properties of Al-2Ce and ternary Al-2Ce-1X (at.%) alloys fabricated by laser powder-bed fusion (LPBF), where X = Mn, Cr, V, Mo, and W are slow-diffusing transition metals. All ternary alloys show a hypereutectic microstructure in the as-LPBF state, containing an interconnected network of eutectic Al 11 Ce 3 phases (~10 vol.%) and an additional population of submicron, equiaxed Al 20 CeX 2 primary precipitates (~10 vol.%) which are isomorphous among these five alloys. Similar microstructures are present in arc-melted rods and atomized powders but are coarser due to the slower cooling rates in these processes. The hardness of the as-LPBF ternary Al-Ce-X alloys (1300–1400 MPa) is higher than that of the binary Al-Ce alloy (~1100 MPa) due to the higher volume fraction of strengthening phases. Furthermore, during exposure at 400 °C for up to three months, greater hardness retention is achieved in the ternary Al-Ce-X alloys (65–75%) than in the binary Al-Ce alloy (~55%), which is attributed to the extreme coarsening resistance of the Al 20 CeX 2 precipitates imparted by the very slow-diffusing ternary solute. These coarsening-resistant Al 20 CeX 2 precipitates also substantially improve alloy creep resistance, increasing the threshold stress for dislocation creep at 300°C from ~32 MPa for the binary Al-Ce alloy to ~77–100 MPa for the ternary Al-Ce-X alloys, and at 400°C from <10 MPa for the binary Al-Ce alloy to >40 MPa for the ternary Al-Ce-V alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effect of Zr and Sc additions on coarsening- and creep resistance of AlSi10Mg fabricated by laser powder bed fusion

Microstructure and creep properties are studied in a eutectic AlSi10Mg alloy modified with Zr and Sc additions (Al-9.8Si-0.32Mg-0.70Zr-0.23Sc, wt%) manufactured through laser powder-bed fusion (L-PBF). Three types of Zr/Sc-bearing powders - elemental, master-alloy, and pre-alloyed - are employed in the fabrication process, with the pre-alloyed powders providing the highest incorporation of Zr and Sc in the Al matrix. Here, the as-printed alloy exhibits a fine cellular Al-Si eutectic structure which fragments and coarsens into micron-sized Si particles during aging at 300 ºC, leading to a steady drop in alloy microhardness between 0.1 and 1000 h. Coarsening of the eutectic Si phase during aging is not measurably affected by Zr and Sc in solid solution, which precipitate during aging and increases strength, compensating weakening from Si coarsening between 1 and 200 h at 300 ºC. Atom-probe analysis in the peak-aged condition (96 h/300 °C) confirms the presence of Al 3 (Sc,Zr) secondary nano-precipitates with an average radius of 1.0 nm and some Si solubility. Micron-sized grains are present throughout the alloy, with ultra-fine-grained regions at the melt pool boundaries, neither of which coarsen during long-term aging at 300 ºC. Under creep conditions at 300 °C, the Zr/Sc-bearing alloy with Al 3 (Sc,Zr) nano-precipitates exhibits power-law behavior, with a high apparent stress exponent (n a = 9) and a high threshold stress (σ th = 43 MPa), exhibiting nearly double the strength of a Zr/Sc-free AlSi10Mg control alloy (σ th = 22 MPa).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of droplet oxidation on mechanical properties of an Al-7Si-0.4Mg alloy fabricated with liquid metal jetting

Droplet-on-demand liquid metal jetting (DOD-LMJ) is a new method for additive manufacturing of bulk structural alloys. Here, we report on the microstructure, tensile, and fatigue properties of an Al-7Si-0.4Mg (A356) alloy fabricated with LMJ. Liquid metal droplets were shielded by high-purity Ar gas shroud during deposition. Atom probe tomography revealed that a few nanometers thick (Al-Mg-Si)-O oxide film formed on the droplets despite Ar gas shielding. Tensile tests on peak-aged LMJ A356 alloy showed that yield strength was isotropic (250 MPa), but ductility was lower in the build direction (6.1 ± 1.4 %) compared to the transverse direction (9.4 ± 1.0 %). Lower ductility in the build direction was attributed to delamination of metal-oxide interfaces at layer boundaries. The ductility and yield strength of LMJ A356 were similar to cast A356 and laser powder bed fused (LPBF) A357 alloys, indicating the limited impact of oxide film on tensile properties. The oxide film severely impacted the fatigue properties. Fatigue resistance of LMJ A356 was limited by fatigue crack initiation at lack-of-fusion defects and fatigue crack propagation along layer boundaries by delamination of the metal-oxide interface. The fatigue strength of LMJ A356 at 60 MPa was lower than cast A356 and LPBF A357 alloys in the peak-aged condition. This research underscores the need for managing droplet oxidation during LMJ additive manufacturing of structural alloys.

42 ENGINEERING↗
DOE OSTI2023

Densification and microstructure features of lithium hydride fabrication

The manufacturing of lithium hydride (LiH) utilizing uniaxial pressing, which offers fabrication with tailorable properties via microstructure control, can lead to the expansion in application of LiH while bypassing the challenges presented by historical casting manufacturing techniques. Through control of consolidation conditions such as pressure, temperature, dwell time and powder load, the presented work highlights the densification of LiH, with an emphasis on quantifying oxygen content, for applications requiring a specific density range necessary for optimized material performance. Karl Fischer Titration and X-ray Diffraction proved useful in determining oxygen and phase content while Computed Tomography and Scanning Electron Microscopy provided structural analysis. The temperature dependent densification of LiH fit with an Arrhenius term resulted in an activation energy of 21.2 kJ/mol. Images of fractured surfaces of LiH pressed at 500 °C revealed drastic grain coarsening, aided by the presence of oxygen impurities.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Properties of Nb3Sn films fabricated by magnetron sputtering from a single target

Superconducting Nb3Sn films were fabricated on sapphire and fine grain Nb substrates by magnetron sputtering from a single stoichiometric Nb3Sn target. The structural, morphological and superconducting properties of the films annealed for 24 h at temperatures of 800-1000 {\deg}C were investigated. The effect of the annealing time at 1000 {\deg}C was examined for 1, 12, and 24 h. The film properties were characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy, energy dispersive X-ray spectroscopy, and Raman spectroscopy. The DC superconducting properties of the films were characterized by a four-point probe measurement down to cryogenic temperatures. The RF surface resistance of films was measured over a temperature range of 6-23 K using a 7.4 GHz sapphire-loaded Nb cavity. As-deposited Nb3Sn films on sapphire had a superconducting critical temperature of 17.21 K, which improved to 17.83 K when the film was annealed at 800 {\deg}C for 24 h. For the films annealed at 1000 {\deg}C, the surface Sn content was reduced to ~11.3 % for an annealing time of 12 h and to ~4.1 % for an annealing time of 24 h. The Raman spectra of the films confirmed the microstructural evolution after annealing. The RF superconducting critical temperature of the as-deposited Nb3Sn films on Nb was 16.02 K, which increased to 17.44 K when the film was annealed at 800 {\deg}C for 24 h.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

All-alumina quarter-wave plate coatings fabricated by glancing angle deposition using serial bideposition

Anisotropic phase retarders, used in high power laser facilities to perform polarization smoothing, can be obtained by the glancing angle deposition (GLAD) coating process. Due to its high laser resistance, the coatings are mainly made of silica. Therefore, limited attention has been given to other dielectric materials. Here we present a study on alumina GLAD anisotropic coatings; a material with high laser resistance, higher birefringence and lower environmental sensitivity than silica. Since the anisotropy is related to the coatings microstructure through the deposition angle, samples were coated at angles varying from ± 68° to ± 82° using the serial bideposition technique. They were characterized by ellipsometry, polarimetry, spectrophotometry and electron microscopy. We showed that the highest birefringence is obtained at a deposition angle of ± 76° with an in-plane value of 0.053. Based on these results, a quarter-wave plate at 351 nm was designed as a multilayer with seven pairs of anisotropic layers deposited at ± 76° and isotropic layers deposited at 0°. The fabricated coating exhibited a uniform retardance of 88.51 ± 0.45 nm. The alumina GLAD wave plates presented here, open the door to new possibilities in the laser field and especially in the field of fusion energy.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electrical and structural characterization of nano-carbon–aluminum composites fabricated by electro-charging-assisted process

Incorporating nano-carbon phases into metal-matrix composites is a promising strategy for simultaneously enhancing electrical conductivity and mechanical properties of metals. Here, we describe the manufacture of novel nano-carbonaluminum composites by an electro-charge-assisted process (EAP) that show 5.6% ± 1.7% increase in electrical conductivity compared to the base metal alloy. The source of nano-carbon that we used in this study is activated carbon with particle size less than 100 nm. The enhancement is attributed to nano-graphitic structures that extend through the lattice of the metal. Through electron transfer from the metal to the nanostructures the electron density at the interface of nano-crystalline graphite and the metal lattice increases thereby enhancing the bulk electrical conductivity. We identify the important fabrication parameters of the EAP for a reaction system employing a tapered graphite cathode. Here, a high current density of 100 A/cm 2 causes ionization and crystallization of the carbon in the liquid metal. The increase in electrical conductivity of the composite are directly related to the incorporation of the nanocrystalline carbon in the metal lattice. The superior performance of these nano-carbon aluminum composites makes them promising candidates for power transmission lines and other applications.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Toward a tunable fabrication of multifunctional iron-aluminum spinels via solution combustion synthesis: The effects of fuel, heating mode, and Fe:Al precursor ratio

The solid solutions of iron and aluminum spinels (hercynite, maghemite, magnetite, and γ-alumina) are promising materials for emerging technologies such as solar thermochemical fuel production and clean dehydrogenation of fossil fuels. Solution combustion synthesis (SCS) is an attractive technique for the fabrication of these materials as it has been used for synthesis of many nanoscale oxides. However, the design space of SCS is large with many synthesis parameters affecting the properties of the combustion products. To optimize the SCS of these materials, it is important to determine which parameters yield the best properties. In the present work, FeAlO x nanocomposites were obtained by SCS using iron nitrate and aluminum nitrate as precursors and oxidizers. Two fuels (citric acid and glycine), three Fe:Al molar ratios (1:2, 1:1, and 2:1) in the precursors, and three heating modes (hotplate, muffle furnace, and microwave oven) were compared. The products were characterized by X-ray diffraction analysis, scanning electron microscopy, Brunauer-Emmett-Teller surface area analysis, and laser diffraction particle size analysis. The fuel used had the largest impact on the combustion behavior and hence the material properties. The high combustion temperature of glycine allowed for the formation of an FeAl 2 O 4 /Fe 3 O 4 solid solution, while the lower-temperature combustion of citric acid yielded Al-substituted γ-Fe 2 O 3 with high amorphous content. With citric acid, the specific surface area as high as 200 m 2 /g was achieved. The effect of Fe:Al precursor ratio was clearly seen in variations of the lattice parameter, which demonstrated the ability to tune the phase composition. The heating mode had minor effects on material properties, but some differences were observed. As a result, all products obtained by SCS in a microwave oven had low specific surface areas compared to those obtained with a hotplate and a muffle furnace.

Alumina↗
DOE OSTI2020

Application of electrospinning for the fabrication of proton-exchange membrane fuel cell electrodes

We report electrospun materials have been gaining great interest in the energy sector. Their tunability and robustness make them highly attractive, particularly for proton-exchange membrane fuel cell (PEMFC) electrodes. Conventional PEMFC electrodes, prepared by either spraying, painting, or slot-die coating, have not yet met the needs of large-scale PEMFC use. Electrospinning of fibrous materials has already shown great promise as an alternative methodology for electrode fabrication. Electrospinning has been used in fuel cell electrodes through two primary means: (1) segmented carbon or inorganic fibers to serve as precious metal catalyst support, and (2) high aspect ratio polymer/particle fibers to serve directly as the electrode. The use of electrospun fibrous electrodes has led to improved PEMFC durability and increased power output at low catalyst loadings, both of which are of paramount importance to large-scale commercialization of PEMFC electric vehicles.

36 MATERIALS SCIENCE↗