Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

A computational study of the effects of graphene additions on electrical properties of polycrystalline copper

The addition of graphene has recently shown promise as a route for the significant improvement of the bulk electrical properties of metallic materials. Here, we explore the effects these additions have on the net electrical conductivity of fabricated copper-graphene (Cu-Gr) nanocomposites as a function of grain structure and grain boundary properties. Synthetic 3D microstructures were generated to represent polycrystalline copper with different average grain diameters and twinned grain boundary fractions. Then, the Poisson equation of electrical transport was solved using a finite difference method in order to predict the net electrical conductivity of each microstructure. In this context, the potential effect of graphene on the conductivity of the composite was evaluated as a function of the number of affected grain boundaries. The results of these calculations indicate that 1.) as supported by literature, net electrical conductivity decreases with decreasing grain size, 2.) the presence of twinned grain boundaries results in smaller loss of conductivity than would otherwise be expected, and 3.) the presence of graphene on the grain boundaries can be expected to lead to improvements in net electrical conductivity. However, we also find that 4.) when the Cu grain structure becomes sufficiently refined, the addition of graphene could conceivably result in significant improvements in electrical conductivity over and above coarse-grained Cu. It is estimated from our calculations that, assuming microstructures with average grain sizes between 100 nm and 100 μm and graphene conductivity 1000 to 10,000 that of a typical Cu grain boundary, an improvement in electrical conductivity of approximately 17% over that of bulk Cu may be attainable. Therefore, by performing this study we suggest a possible route for the improvement of Cu electrical properties through the addition of graphene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-scale investigation on mechanical behavior and microstructural alteration of C-S-H in carbonated Alite paste

Carbonation treatment is a promising option to enhance recycled concrete aggregate (RCA) quality and eventually improve concrete performance. This study investigated the multi-scale mechanical properties of calcium silicate hydrates (C-S-H) in a mature alite paste subjected to accelerated carbonation treatment by testing macro compressive strength, microhardness and nanoindentation. The results show that, carbonation treatment resulted in a heterogeneous distribution of carbonation products in the alite sample. Reinforcement of C-S-H by the randomly precipitated calcite and vaterite crystals prevailed over the nano-structural and compositional alteration of C-S-H induced by carbonation, leading to an increase of nano-indentation modulus at the edge of the sample. Also, the microhardness at the edge zone was markedly higher than that at the core of the carbonated sample. The carbonated peripheral zone with improved nano-scale modulus and microhardness was likely serving as a “hard shell”, contributing to the improved macro compressive strength. The new insights into the multi-scale mechanical properties of carbonated C-S-H contribute to further understanding of the enhanced properties of RCA after carbonation treatment.

36 MATERIALS SCIENCE↗

Development of a Squeeze Semisolid High-Pressure Die Casting Process for Magnesium Structural Parts

High-pressure die casting is the most common method used to produce magnesium castings, due to the excellent balance of cost and properties for high production volumes with limitations in terms of final mechanical properties. A newly developed process based on employing low injection speeds, in a range slightly over the standard semisolid speeds with a modified die, with thick gates and high die temperatures has been developed. Despite working with speeds that are not in the lamellar flow, the obtained parts present very low porosity, allowing the use thermal treatments to increase the ductility without producing blisters. The demonstration has been performed in a AM60B magnesium body joint produced by the squeeze casting process. Finally, the microstructure and the mechanical properties of as-cast and T4 heat-treated samples were studied. The results indicate the improvement of the mechanical properties in T4 heat-treated parts; specifically, a 40% improved deformation-to-failure, 40-60% improved penetration force and 90% of energy absorption were possible to obtain employing the newly developed SC + T4 process.

36 MATERIALS SCIENCE↗

Design and development of a high-performance Ni-based superalloy WSU 150 for additive manufacturing

This work proposes a design and development strategy of a new nickel-based superalloy for additive manufacturing. A new Ni-based superalloy has been developed by the application of the combinatorial alloy development technique coupled with CALPHAD based solidification modeling by effectively suppressing the precipitation kinetics. The suppression of precipitation during processing paved a way for prevention of cracks during deposition. The new alloy "WSU 150" revealed excellent room temperature mechanical properties with a yield strength of 867 MPa, an ultimate tensile strength of 1188 MPa, and an elongation of 27.9% in the as-deposited condition. The mechanical properties of the heat-treated alloy were improved significantly to 1114 MPa yield strength, 1396 MPa ultimate tensile strength, and an elongation of 16.1%. Improvement in the mechanical properties is attributed to the additional precipitation and coarsening of γ' and carbides during heat-treatment. Microstructural investigation of the alloy revealed spherical γ' with a rippled size distribution from the center to the interdendritic region. The average size of the γ' particles in the as-deposited condition was found to be around 48 nm in the interdendritic region. Heat-treatment promoted the coarsening of γ' which is explained in the paper.

36 MATERIALS SCIENCE↗

Precision surface modification of solid oxide fuel cells via layer-by-layer surface sol–gel deposition

While solid oxide fuel cells (SOFCs) are a promising technology for a clean and sustainable future, their commercialization is hindered by limited durability and performance. Here, we report our findings on the application of a layer-by-layer surface sol–gel (SSG) coating of catalysts to dramatically enhance the electro-catalytic activity and durability of SOFC cathodes. The SSG process is capable of penetrating and preserving complex backbone microstructures of porous electrodes, creating highly conformal coatings of controlled morphology, while tailoring the composition of the surface to improve catalytic properties and durability. For example, the application of an SSG coating of PrO x to a La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3–δ (LSCF) cathode has reduced the polarization resistance from 1.136 to 0.117 Ω cm 2 at 600 °C and the degradation rate from 1.13 × 10 –3 to 2.67 × 10 –4 Ω cm 2 h –1 at 650 °C. In addition, a continuous improvement in electrode performance is demonstrated as the thickness of the coating is increased, corresponding to the linear addition of catalyst. Furthermore, this first application of the SSG technique to SOFC systems opens the door for the controlled surface modification of porous components in electrochemical systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of cryogenic treatment on the plastic property of Ti-6Al-4V titanium alloy

The effect of cryogenic treatment on the plastic property of Ti-6Al-4V plate was studied in the present work. After cryogenic treatment, the low temperature temper at 180 ▭ was conducted in one of the groups and the results were compared with that of the untreated and cryotreated ones. The SLX series program controlled cryogenic equipment was used for the cryogenic treatment. The tensile tests were conducted by universal tensile testing machine and parameters of elongation and area reduction were used to evaluate plastic property. The scanning electron microscope was used to study the morphology of microstructure and fracture surface. The results show that after cryogenic treatment alone the elongation increased 10.6% and the area reduction increased 13.5% while the strength reduced to a small extent. Cryogenic treatment followed with low temperature temper increased the elongation and area reduction just by the extent of 4.7% and 9.5%. It means that the additional low temperature temper after cryogenic is not beneficial to the tensile properties of Ti-6Al-4V alloy. The examination of microstructure by scanning electron microscopy revealed that cryogenic treatment reduced the content of β phase particles which is the main reason for the improvement in plasticity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of high-temperature annealing on the microstructure and thermoelectric properties of GaP doped SiGe

Annealing of GaP doped SiGe will significantly alter the thermoelectric properties of the material resulting in increased performance as measured by the figure of merit Z and the power factor P. The microstructures and corresponding thermoelectric properties after annealing in the 1100 to 1300 C temperature range have been examined to correlate performance improvement with annealing history. The figure of merit and power factor were both improved by homogenizing the material and limiting the amount of cross-doping. Annealing at 1215 C for 100 hr resulted in the best combination of thermoelectric properties with a resultant figure of merit exceeding 1x10 to the -3 deg C to the -1 and a power factor of 44 microW/cm/deg C sq for the temperature range of interest for space power: 400 to 1000 C.

Draper, Susan L.↗

On the preparation of TiAl alloy by direct reduction of the oxide mixtures in calcium chloride melt

In recent years, TiAl-based intermetallic alloys are being increasingly considered for application in areas such as (i) automobile/transport sector (passenger cars, trucks and ships) (ii) aerospace industry (jet engines and High Speed Civil Transport propulsion system) and (iii) industrial gas turbines. These materials offer excellent (i) high temperature properties (at higher than 6000C) (ii) mechanical strength and (iii) resistance to corrosion and as a result have raised renewed interest. The combination of these properties make them possible replacement materials for traditional nickel-based super-alloys, which are nearly as twice as dense (than TiAl based alloys). Since the microstructures of these intermetallic alloys affect, to a significant extent, their ultimate performance, further improvements (by way of alteration/modification of these microstructures), have been the subject matter of intense research investigations. It has now been established that the presence of alloy additives, such as niobium, tantalum, manganese, boron, chromium, silicon, nickel and yttrium etc, in specific quantities, impart marked improvement to the properties, viz. fatigue strength, fracture toughness, oxidation resistance and room temperature ductility, of these alloys. From a number of possible alloy compositions, {gamma}-TiAl and Ti-Al-Nb-Cr have, of late, emerged as two promising engineering alloys/materials. . The conventional fabrication process of these alloys include steps such as melting, forging and heat treatment/annealing of the alloy compositions. However, an electrochemical process offers an attractive proposition to prepare these alloys, directly from the mixture of the respective oxides, in just one step. The experimental approach, in this new process, was, therefore, to try to electrochemically reduce the (mixed) oxide pellet to an alloy phase. The removal of oxygen, from the (mixed) oxide pellet, was effected by polarizing the oxide pellet against a graphite electrode in a pool of molten calcium chloride at a temperature of 9000C. The dominant mechanism of the oxygen removal was the ionization of oxygen followed by its subsequent discharge, as CO2/CO, at the anode surface. The removal of oxygen from the oxide mixture helped form the alloy in situ. The presentation shall cover the detailed experimental results pertaining to the preparation, evaluation and characterization of Ti-47Al-2Nb-2Cr (atom%) alloy.

36 MATERIALS SCIENCE↗

Effect of Nb micro-alloying on microstructure and properties of thermo-mechanically processed high carbon pearlitic steel

Highlights: • Effect of Nb micro-alloying on high carbon steels has been established. • Fine and degenerated pearlite with fine PAGS is achieved due to Nb micro-alloying. • AFM study indicates true interlamellar spacing which conforms well to TEM study. • Hardness and yield strength have been obviously improved with the addition of Nb. - Abstract: Two C-Mn-Si steels with and without Nb micro-alloying are selected in the present study. Both these high carbon steels have been thermo-mechanically processed using Gleeble 3800 simulator. Optical microscope (OM), scanning electron microscope (SEM), transmission electron microscope (TEM), atomic force microscope (AFM) were utilised for microstructural characterisation. The austenitising temperature was varied from 1150 °C to 1200 °C followed by hot compression and subjected to free cooling to evaluate the influence of austenite grain size on transformed microstructure and mechanical properties. It is evident that higher austenite grain size is obtained for both types of steels subjected to higher austenitising temperature. The refinement of pearlite interlamellar spacing (<0.20 μm) with degenerated morphology as well as finer prior austenite grain size (<40 μm) is found to be more prominent for Nb micro-alloyed sample. The average hardness values of both the steels are higher for the specimens, treated at a higher austenitising temperature which is attributed to finer interlamellar spacing. Finally, the correlation between the evolving microstructure and resulting mechanical properties (hardness and yield strength) has been made.

36 MATERIALS SCIENCE↗

Effect of Heat Treatment on Microstructure and Mechanical Properties of Extruded Mg-4Zn-1.5Al-2Sn Alloy

The microstructure and mechanical properties of extruded Mg-4Zn-1.5Al-2Sn (ZAT422) alloy under different heat treatments were investigated by optical microscopy, scanning electron microscopy, x-ray diffraction, transmission electron microscopy, micro-hardness tests, and tensile tests. The results show that the as-extruded and heat-treated ZAT422 alloys mainly consisted of α-Mg and Mg{sub 2}Sn, and no ternary phase was detected. After aging, the amount of secondary phase precipitates increased significantly and the mechanical properties were improved. Among all the heat treatments, T5 heat treatment at 150 °C for 25 h resulted in the best combination of strength and ductility for ZAT422 alloy. The ultimate tensile strength, yield strength, and elongation (ε{sub f}) were found to be 290, 182 MPa, and 20%, respectively. Based on microstructural characterization, the variations in mechanical properties of the alloy subjected to heat treatment were analyzed in detail.

36 MATERIALS SCIENCE↗

Influence of Indium on Microstructure and Properties of Sn-Pb Binary Alloy Applied in Photovoltaic Ribbon

In this work, the conductivity, melting point, microstructure, spreading behavior, and mechanical properties of three types of Sn-Pb-In(indium) alloys are investigated along with Sn60Pb40 alloy as a reference. The results show that the In element improves the comprehensive properties of the Sn-Pb alloys. The maximum conductivity of the Sn-Pb-In alloys is 7.08 MS/m when the content of the In element is 3 wt.%. With an increasing content of the In element, the melting points of the Sn-Pb-In alloys gradually decrease from 183 to 166 °C. The microstructures of the alloys are refined with the addition of In. The intermetallic compound (IMC) InSn{sub 4} is only found in Sn60Pb34In6, except for the α-Pb and β-Sn phases. A spread test shows that only IMC Cu{sub 6}Sn{sub 5} is present at the Cu/solder interface of the solder joints. The Sn60Pb34In3 solder joint shows the highest ultimate tensile strength of 54 MPa. The microhardness of the alloys slightly increases from 12.76 HV{sub 0.05} to 13.56 HV{sub 0.05} with the In content increasing from 0 to 3 wt.%, while a sharp increase to 15.53 HV{sub 0.05} is observed when the amount of In exceeds 3 wt.%.

36 MATERIALS SCIENCE↗

Improved ferroelectric polarization of V-doped Bi{sub 6}Fe{sub 2}Ti{sub 3}O{sub 18} thin films prepared by a chemical solution deposition

We prepared V-doped Bi{sub 6}Fe{sub 2}Ti{sub 3}O{sub 18} thin films on Pt/Ti/SiO{sub 2}/Si (100) substrates by using a chemical solution deposition route and investigated the doping effect on the microstructure, dielectric, leakage, and ferroelectric properties of Bi{sub 6}Fe{sub 2}Ti{sub 3}O{sub 18} thin films. The Bi{sub 5.97}Fe{sub 2}Ti{sub 2.91}V{sub 0.09}O{sub 18} thin film exhibits improved dielectric properties, leakage current, and ferroelectric properties. The incorporation of vanadium resulted in a substantially enhanced remnant polarization (2P{sub r}) over 30 μC/cm{sup 2} in Bi{sub 5.97}Fe{sub 2}Ti{sub 2.91}V{sub 0.09}O{sub 18} thin film compared with 10 μC/cm{sup 2} in Bi{sub 6}Fe{sub 2}Ti{sub 3}O{sub 18} thin film. It is demonstrated that the improved properties may stem from the improvement of crystallinity of the films with the contribution of suppressed oxygen vacancies and decreased mobility of oxygen vacancies caused by the V-doping. The results will provide a guidance to optimize the ferroelectric properties in Bi{sub 6}Fe{sub 2}Ti{sub 3}O{sub 18} thin films by chemical solution deposition, which is important to further explore single-phase multiferroics in the n = 5 Aurivillius thin films.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Improved microstructure of cement-based composites through the addition of rock wool particles

Rock wool is an inorganic fibrous substance produced by steam blasting and cooling molten glass. As with other industrial by-products, rock wool particles can be used as cementitious materials or ultra fine fillers in cement-based composites. This study investigated the microstructure of mortar specimens produced with cement-based composites that include various forms of rock wool particles. It conducted compressive strength testing, rapid chloride penetration tests, X-ray diffraction analysis, thermo-gravimetric analysis, and scanning electronic microscopy to evaluate the macro- and micro-properties of the cement-based composites. Test results indicate that inclusion of rock wool particles in composites improved compressive strength and reduced chloride ion penetration at the age of 91 days due to the reduction of calcium hydroxide content. Microscopic analysis confirms that the use of rock wool particles contributed to the formation of a denser, more compact microstructure within the hardened paste. In addition, X-ray diffraction analysis shows few changes in formation of pozzolanic reaction products and no new hydrations are formed with incorporating rock wool particles. - Highlights: • We report the microstructural characterization of cement-based composites. • Different mixes produced with various rock wool particles have been tested. • The influence of different mixes on macro and micro properties has been discussed. • The macro properties are included compressive strength and permeability. • XRD and SEM observations confirm the pozzolanic reaction in the resulting pastes.

36 MATERIALS SCIENCE↗

Effect of short-range order on microstructure, texture and strain hardening of cold drawn Cu-10 at.%Mn alloy

Highlights: • Excluding the effect of stacking fault energy, short-range order effect is discussed solely. • Short-range order is beneficial for twinning and slip planarity. • Short-range order promotes the formation of <111> fiber texture. • Strain hardening improving by short-range order. - Abstract: The aim of the present study is to investigate the effect of short-range order (SRO) on the microstructural evolution and mechanical property of Cu-10 at.%Mn alloy during cold drawing deformation. Characterization of the cold drawn Cu-10 at.%Mn alloy samples were performed using transmission electron microscope (TEM) and electron back scattering diffraction (EBSD), and their hardness were also tested. The results show that SRO is beneficial for both twinning and the transition of dislocation glide from wavy slip to planar slip at the low strains. At the high strains, the wavy slip generates due to the destruction of SRO. SRO increases the volume fraction of <111> texture component and the critical strain threshold. Moreover, the presence of SRO significantly improves strain hardening by combining the effects of dislocation, deformation twinning and texture hardening, which results in a significant increase of hardness.

36 MATERIALS SCIENCE↗

Structures, electrical properties, and leakage current behaviors of un-doped and Mn-doped lead-free ferroelectric K{sub 0.5}Na{sub 0.5}NbO{sub 3} films

Lead-free ferroelectric un-doped and doped K{sub 0.5}Na{sub 0.5}NbO{sub 3} (KNN) films with different amounts of manganese (Mn) were prepared by a chemical solution deposition method. The thicknesses of all films are about 1.6 μm. Their phase, microstructure, leakage current behavior, and electrical properties were investigated. With increasing the amounts of Mn, the crystallinity became worse. Fortunately, the electrical properties were improved due to the decreased leakage current density after Mn-doping. The study on leakage behaviors shows that the dominant conduction mechanism at low electric field in the un-doped KNN film is ohmic mode and that at high electric field is space-charge-limited and Pool-Frenkel emission. After Mn doping, the dominant conduction mechanism at high electric field of KNN films changed single space-charge-limited. However, the introduction of higher amount of Mn into the KNN film would lead to a changed conduction mechanism from space-charge-limited to ohmic mode. Consequently, there exists an optimal amount of Mn doping of 2.0 mol. %. The 2.0 mol. % Mn doped KNN film shows the lowest leakage current density and the best electrical properties. With the secondary ion mass spectroscopies and x-ray photoelectron spectroscopy analyses, the homogeneous distribution in the KNN films and entrance of Mn element in the lattice of KNN perovskite structure were also confirmed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tailoring the γ-γ'-γ" dual superlattice microstructure of INCONEL® 725 by high temperature aging and Nb/Ta additions for superior creep properties

Next-generation energy systems require superior resistance to creep deformation due to the considerably prolonged exposure times at operating stress and temperature. To improve the elevated temperature properties of INCONEL® 725 (IN725), a corrosion resistant alloy, several variants with different Ti/Al ratio and judicious amounts of Nb and Ta were made. Furthermore, a high temperature aging (HTA) heat treatment, designed to promote favorable precipitate phase formation, was explored. These adjustments allowed to tailor the amount and type of precipitate strengthening which led to significant increases in time to failure. The Ti/Al ratio was used to favor the formation of γ' or γ" precipitates. Compact morphology precipitates, consisting of γ' precipitates surrounded by a γ" shell, were formed in alloys with a low Ti/Al ratio. The HTA increased the creep life of various alloy formulations up to a maximum improvement of 371% as compared to the standard aging heat treatment. The Nb and Ta additions had a similar effect on increasing creep life by promoting and stabilizing γ" precipitation. The positive effect of the additions was even more pronounced when coupled with the HTA. A phase stability study with up to 10,000 h exposure at 700°C revealed that the compact morphology helped in slightly reducing coarsening of the γ' precipitates, although the effect on creep was not significant. The findings of this study enable design of dual superlattice alloys through microstructural engineering that yields superior performance and can be applied to a wide range of alloys in the IN718 and derivatives family.

Antonov, Stoichko↗

Microstructures and photocatalytic properties of Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} films prepared by sol-gel method

Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} films were successfully prepared by the improved sol-gel and doping processes. The as-prepared specimens were characterized using differential thermal analysis-thermogravimetry (DTA-TG), X-ray diffraction (XRD), high-resolution field emission scanning electron microscopy (FE-SEM), X-ray energy dispersive spectroscopy (EDS), Brunauer-Emmett-Teller (BET) surface area, Photoluminescence spectrum (PL) and UV-vis diffuse reflectance spectroscopy. The photocatalytic activities of the films were evaluated by degradation of an organic dye in aqueous solution. The results of XRD, FE-SEM and BET analyses indicated that the TiO{sub 2} films were composed of nano-particles or aggregates with a size of less than 10 nm. With the codoping of Ag{sup +} and La{sup 3+}, TiO{sub 2} films with high photocatalytic activity and clearly responsive to the visible light were obtained. The improvement mechanism by ions doping was also discussed. - Graphical Abstract: The PL intensity of Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} was the lowest among all samples, indicating the recombination of electron and hole was effectively prohibited compared with pure TiO{sub 2}, Ag{sup +} and La{sup 3+} bulk codoped TiO{sub 2}. Highlights: > Ag{sup +} and La{sup 3+} codoping can reduce the crystal size of TiO{sub 2}. > Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} films have an obvious optical response red-shift. > Ag{sup +} and La{sup 3+} surface codoped TiO{sub 2} films can exhibit excellent photocatalytic activity under both UV and visible light irradiations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Guiding the Design of Heterogeneous Electrode Microstructures for Li-Ion Batteries: Microscopic Imaging, Predictive Modeling, and Machine Learning

Electrochemical and mechanical properties of lithium-ion battery materials are heavily dependent on their 3D microstructure characteristics. A quantitative understanding of the role played by stochastic microstructures is critical for the prediction of material properties and for guiding synthesis processes. Furthermore, tailoring microstructure morphology is also a viable way of achieving optimal electrochemical and mechanical performances of lithium-ion cells. To facilitate the establishment of microstructure-resolved modeling and design methods, a review covering spatially and temporally resolved imaging of microstructure and electrochemical phenomena, microstructure statistical characterization and stochastic reconstruction, microstructure-resolved modeling for property prediction, and machine learning for microstructure design is presented here. The perspectives on the unresolved challenges and opportunities in applying experimental data, modeling, and machine learning to improve the understanding of materials and identify paths toward enhanced performance of lithium-ion cells are presented.

25 ENERGY STORAGE↗