Search NASA⌕ Search

SEARCH · Search NASA

Results for “low viscosity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Physics of Hard Sphere Experiment: Scattering, Rheology and Microscopy Study of Colloidal Particles

The Physics of Hard Sphere Experiment has two incarnations: the first as a scattering and rheology experiment on STS-83 and STS-94 and the second as a microscopy experiment to be performed in the future on LMM on the space station. Here we describe some of the quantitative and qualitative results from previous flights on the dynamics of crystallization in microgravity and especially the observed interaction of growing crystallites in the coexistance regime. To clarify rheological measurements we also present ground based experiments on the low shear rate viscosity and diffusion coefficient of several hard sphere experiments at high volume fraction. We also show how these experiments will be performed with confocal microscopy and laser tweezers in our lab and as preparation for the phAse II experiments on LMM. One of the main aims of the microscopy study will be the control of colloidal samples using an array of applied fields with an eye toward colloidal architectures. Temperature gradients, electric field gradients, laser tweezers and a variety of switchable imposed surface patterns are used toward this control.

Z D Cheng↗
NASA NTRS2003

High Temperature Transfer Molding Resins: Status of PETI-298 and PETI-330

Two phenylethynyl terminated oligomers designated PETI-298 and PETI-330 were developed at the NASA Langley Research Center and have emerged as leading candidates for composite applications requiring high temperature performance (i.e. greater than or equal to 288 C for 1000 hours) combined with the ability to be readily processed into composites without the use of an autoclave or complex/lengthy cure or post-cure cycle. These high performance/high temperature composites are potentially useful on advanced aerospace vehicles in structural applications and as aircraft engine components such as inlet frames and compressor vanes. The number designation (i.e. 298, 330) refers to the glass transition temperature in degrees Celsius as determined on neat resin cured for 1 hour at 371 C. The resins are processable by non-autoclave techniques such as resin transfer molding (RTM), vacuum assisted RTM (VARTM) and resin infusion (RI). Both resins exhibit low complex melt viscosities (0.1-10 poise) at 280 C and are stable for greater than or equal to 2 hours at this temperature. Typically, the resins are melted, de-gassed and infused or injected at 280 C and subsequently cured at 371 C for 1-2 hours. Virtually no volatiles are evolved during the cure process. The resin synthesis is straightforward and has been scaled-up to 25 kg batches. The chemistry of PETI-298 and PETI-330 and the RTM AS-4 and T-650 carbon fabric laminate properties, and those of BMI-5270 for comparison, are presented.

Connell, John W.↗
NASA NTRS2004

Organic Modification of a Layered Silicate by Co-Ion Exchange of an Alkyl Ammonium and a Mono-Protonated Diamine

Co-Ion exchange of the interlayer cations of a layered silicate with a mono-protonated aromatic diamine and an alkyl ammonium ion into the silicate galleries. The presence of the alkyl ammonium ion provides low oligomer melt viscosity during processing. The presence of the diamine allows chemical reaction between the silicate surface modification and the monomers. This reaction strengthens the polymer silicate interface, and ensures irreversible separation of the individual silicate layers. Improved polymer thermal oxidative stability and mechanical properties are obtained.

Sandi G Campbell↗
NASA NTRS2000

Time-Dependent Reversible-Irreversible Deformation Threshold Determined Explicitly by Experimental Technique

Structural materials for the design of advanced aeropropulsion components are usually subject to loading under elevated temperatures, where a material's viscosity (resistance to flow) is greatly reduced in comparison to its viscosity under low-temperature conditions. As a result, the propensity for the material to exhibit time-dependent deformation is significantly enhanced, even when loading is limited to a quasi-linear stress-strain regime as an effort to avoid permanent (irreversible) nonlinear deformation. An understanding and assessment of such time-dependent effects in the context of combined reversible and irreversible deformation is critical to the development of constitutive models that can accurately predict the general hereditary behavior of material deformation. To this end, researchers at the NASA Glenn Research Center at Lewis Field developed a unique experimental technique that identifies the existence of and explicitly determines a threshold stress k, below which the time-dependent material deformation is wholly reversible, and above which irreversible deformation is incurred. This technique is unique in the sense that it allows, for the first time, an objective, explicit, experimental measurement of k. The underlying concept for the experiment is based on the assumption that the material s time-dependent reversible response is invariable, even in the presence of irreversible deformation.

Castelli, Michael G.↗
NASA NTRS2005

Modifying Silicates for Better Dispersion in Nanocomposites

An improved chemical modification has been developed to enhance the dispersion of layered silicate particles in the formulation of a polymer/silicate nanocomposite material. The modification involves, among other things, the co-exchange of an alkyl ammonium ion and a monoprotonated diamine with interlayer cations of the silicate. The net overall effects of the improved chemical modification are to improve processability of the nanocomposite and maximize the benefits of dispersing the silicate particles into the polymer. Some background discussion is necessary to give meaning to a description of this development. Polymer/silicate nanocomposites are also denoted polymer/clay composites because the silicate particles in them are typically derived from clay particles. Particles of clay comprise layers of silicate platelets separated by gaps called "galleries." The platelet thickness is 1 nm. The length varies from 30 nm to 1 m, depending on the silicate. In order to fully realize the benefits of polymer/silicate nanocomposites, it is necessary to ensure that the platelets become dispersed in the polymer matrices. Proper dispersion can impart physical and chemical properties that make nanocomposites attractive for a variety of applications. In order to achieve nanometer-level dispersion of a layered silicate into a polymer matrix, it is typically necessary to modify the interlayer silicate surfaces by attaching organic functional groups. This modification can be achieved easily by ion exchange between the interlayer metal cations found naturally in the silicate and protonated organic cations - typically protonated amines. Long-chain alkyl ammonium ions are commonly chosen as the ion-exchange materials because they effectively lower the surface energies of the silicates and ease the incorporation of organic monomers or polymers into the silicate galleries. This completes the background discussion. In the present improved modification of the interlayer silicate surfaces, the co-ion exchange strengthens the polymer/silicate interface and ensures irreversible separation of the silicate layers. One way in which it does this is to essentially tether one amine of each diamine molecule to a silicate surface, leaving the second amine free for reaction with monomers during the synthesis of a polymer. In addition, the incorporation of alkyl ammonium ions into the galleries at low concentration helps to keep low the melt viscosity of the oligomer formed during synthesis of the polymer and associated processing - a consideration that is particularly important in the case of a highly cross-linked, thermosetting polymer. Because of the chemical bonding between the surface-modifying amines and the monomers, even when the alkyl ammonium ions become degraded at high processing temperature, the silicate layers do not aggregate and, hence, nanometer-level dispersion is maintained.

Campbell, Sandi↗
NASA NTRS2018

The Interplay Between Radiation Pressure and the Photoelectric Instability in Optically Thin Disks of Gas and Dust

In optically thin disks, dust grains are photoelectrically stripped of electrons by starlight, heating nearby gas and possibly creating a dust clumping instability-the photoelectric instability (PeI)-that significantly alters global disk structure. In the current work, we use the Pencil Code to perform the first numerical models of the PeI that include stellar radiation pressure on dust grains in order to explore the parameter regime in which the instability operates. In some models with low gas and dust surface densities, we see a variety of dust structures, including sharp concentric rings. In the most gas- and dust-rich models, nonaxisymmetric clumps, arcs, and spiral arms emerge that represent dust surface density enhancements of factors of ∼5-20. In one high gas surface density model, we include a large, low-order gas viscosity and find that it observably smooths the structures that form in the gas and dust, suggesting that resolved images of a given disk may be useful for deriving constraints on the effective viscosity of its gas. Our models show that radiation pressure does not preclude the formation of complex structure from the PeI, but the qualitative manifestation of the PeI depends strongly on the parameters of the system. The PeI may provide an explanation for unusual disk morphologies, such as the moving blobs of the AU Mic disk, the asymmetric dust distribution of the 49Ceti disk, and the rings and arcs found in the HD 141569A disk.

photoelectric instability (PeI)↗
NASA NTRS1984

The effect of viscosity on impact cratering and possible application to the icy satellites of Saturn and Jupiter

Impact experiments in Newtonian fluids with a range of viscosities of 0.001 to 60 Pa s demonstrate that transient crater volume and shape depend on target viscosity as well as on gravity. Volume is reduced, and depth-to-diameter ratio is increased for cratering events in which viscosity plays a dominant role. In addition to being affected by target kinematic viscosity, viscous scaling is most strongly influenced by projectile diameter, less strongly by projectile velocity, and least strongly by gravity. In a planetary context, viscous effects can occur for craters formed by small or slow moving impacting bodies, low planetary surface densities, high surface viscosities, and low gravity values; conditions all likely for certain impacts into the icy satellites of Saturn and Jupiter, especially if liquid mantles were still present beneath solid crusts. Age dating based on crater counts and size-frequency distributions for these icy bodies may have to be modified to account for the possibility that viscosity-dominated craters were initially smaller and deeper than their gravity-controlled counterparts.

Fink, J.↗
DOE OSTI2024

Effect of glass forming additives on low-activity waste feed conversion to glass

A significant effort was invested in the past to develop and refine mathematical models that relate the composition of nuclear waste glasses with their properties, such as viscosity, electrical conductivity, or chemical durability. However, less attention has been paid to the formulation of the melter feed itself, such as the chemical form and the particle size of the glass forming and modifying additives (GFMA), which have a significant effect on the feed-to-glass conversion process during melting. To address this issue, we systematically changed the mineral composition of a simulated low-activity waste melter feed and inspected its melting behavior. When substituting minerals with corresponding oxides and hydroxides, we found that different alumina sources (kyanite, gibbsite, boehmite, or corundum) had the strongest effect on the feed melting process, whereas the sources of Ca, Mg, and Zr had little effect. Further, the x-ray diffraction analysis showed that the alumina sources differ in their dissolution kinetics: early dissolving alumina sources, such as gibbsite (Al(OH) 3 ) and boehmite (AlO(OH)), increase the transient glass-forming melt viscosity at early stages, when gases still evolve, causing extended foaming, whereas alumina sources that dissolve at high temperatures, such as kyanite (Al 2 SiO 5 ) and corundum (Al 2 O 3 ), keep the transient glass-forming melt viscosity low and lead to a faster foam collapse. Using viscosity-composition relationship to estimate the viscosity of transient glass-forming melts in the primary foaming range, we found that the primary foam began to collapse at 360 to 800 Pa s, and fully collapsed between 65 and 260 Pa s. This result agrees with our previous studies, according to which the glass-forming melt viscosity at the cold cap foam bottom ranged from 24 to 85 Pa s.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2002

Polar Wander on Triton and Pluto Due to Volatile Migration

Polar wander may occur on Triton and Pluto because of volatile migration. Triton, with its low obliquity, can theoretically sublimate volatiles (mostly nitrogen) at the rate of approximately 10(exp 14) kilograms per year from the equatorial regions and deposit them at the poles. Assuming Triton to be rigid on the sublimation timescale, after approximately 10(exp 5) years the polar caps would become large enough to cancel the rotational flattening, with a total mass equivalent to a global layer approximately 120-250 m in depth. At this point the pole wanders about the tidal bulge axis, which is the line joining Triton and Neptune. Rotation about the bulge axis might be expected to disturb the leading side/trailing side cratering statistics. Because no such disturbance is observed, it may be that Triton's mantle viscosity is too high but its surface volatile inventory is too low to permit wander. On the other hand, its mantle viscosity might be low, so that any uncompensated cap load might be expected to wander toward the tidal bulge axis. In this case, the axis of wander passes through the equator from the leading side to the trailing side; rotation about this wander axis would not disturb the cratering statistics. Low-viscosity polar wander may explain the bright southern hemisphere: this is the pole which is wandering toward the equator. In any case the permanent polar caps may be geologically very young. Polar wander may possibly take place on Pluto, due to its obliquity oscillations and perihelion-pole geometry. However, Pluto is probably not experiencing any wander at present. The Sun has been shining strongly on the poles over the last half of the obliquity cycle, so that volatiles should migrate to the equator, stabilizing the planet against wander. Spacecraft missions to Triton and Pluto which measure the dynamical flattening could give information about the accumulation of volatiles at the poles. Such information is best obtained by measuring gravity and topography from orbiters, as was done for Mars with the highly successful Mars Global Surveyor.

Rubincam, David Parry↗
NASA NTRS2000

Chondrules in the LEW85332 Ungrouped Carbonaceous Chondrite: Fractionation Processes in the Solar Nebula

We studied 14 chondrules separated from LEW85332, an ungrouped type-3 carbonaceous chondrite related to CR chondrites; 23 elements were determined by neutron activation and the chondrules were characterized petrographically. Oxygen isotopic compositions were determined by R. N. Clayton and T. K. Mayeda for seven chondrules. Chondrule abundance ratios tend to form one of two distinct patterns. In low FeO chondrules, refractory lithophile patterns are flat (i.e., unfractionated); siderophile abundances are high and show a small decrease with increasing volatility. Although high FeO chondrules also have flat refractory lithophile abundance patterns, siderophile abundances are highly fractionated; refractory Ir is very low and Fe is very high relative to other siderophiles. We suggest that the low FeO chondrules in LEW85332 formed early in nebular history when metal was intimately mixed with silicates in the chondrule precursors, and that the viscosity of the liquid-solid mix was too high to permit expulsion of the metal by centrifugal action; their porphyritic structures are consistent with incomplete melting, which would result in relatively high viscosities. When the high FeO chondrules formed somewhat later, much of the Fe was oxidized and the melting of precursors was more extensive, FeO and other oxidized siderophiles were retained in the silicate liquid, and metal was lost, possibly expelled from low viscosity chondrule melts. The O isotopic compositions of the chondrules form a linear array of slope 0.93 +/- 0.05 on a three-isotope diagram, parallel to the carbonaceous chondrite anhydrous minerals (CCAM) line and a CR chondrule array, but offset from the latter by -1% in (delta)O-18. Some or all of this offset may reflect incorporation of O from Antarctic water during weathering. Chondrule (Delta)O-17 values correlate positively with FeO, possibly indicating that the (Delta)O-17 of the nebular gas composition increased with time. The chemical and O isotopic data suggest a temporal sequence extending from early, low FeO to late high FeO chondrules.

Wasson, John T.↗
DOE OSTI2022

Predicted Melt Curve and Liquid Shear Viscosity of RDX up to 30 GPa

Recent grain-scale simulations of HMX and TATB have shown that predictions for hot spot formation in high explosives are particularly sensitive to accurate determinations of the pressure-dependent melt curve and the shear viscosity of the liquid phase. These physics terms are poorly constrained beyond ambient pressure for the explosive RDX. Here we adopt an all-atom modeling approach using molecular dynamics (MD) simulations to predict the melt curve of RDX near to detonation conditions (30 GPa) and determine the shear viscosity of the liquid as a function of temperature and pressure above the melt curve. Phase-coexistence simulations were used to determine the melt curve, which is predicted to vary by almost 1100 K as the pressure increases from 0 GPa to 30 GPa. Equilibrium MD simulations and the Green-Kubo formalism were used to obtain the pressure-temperature-dependent shear viscosity. The shear viscosity of RDX is predicted to be of similar magnitude to the viscosity of TATB at low GPa-range pressures, and to be roughly an order of magnitude lower than the viscosity of HMX. The temperature dependence of the shear viscosity is Arrhenius at a given pressure, and the exponential pre-factor and activation term exhibit a strong, yet complicated, pressure dependence. An empirical pressure-temperature dependent function for RDX shear viscosity is developed that simultaneously captures a wide range of MD predictions while taking an analytic form that extrapolates smoothly beyond the fitted regime. The relative strength of the pressure and temperature dependencies of these two physics terms is found to be of similar magnitude for RDX, HMX, and TATB, which motivates incorporating these results in future RDX grain-scale modeling.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Transport Phenomena in Low Temperature Lithium-Ion Battery Electrolytes

Lithium-ion batteries face low temperature performance issues, limiting the adoption of technologies ranging from electric vehicles to stationary grid storage. This problem is thought to be exacerbated by slow transport within the electrolyte, which in turn may be influenced by ion association, solvent viscosity, and cation transference number. How these factors collectively impact low temperature transport phenomena, however, remains poorly understood. Here we show using all-atom classical molecular dynamics (MD) simulations that the dominant factor influencing low temperature transport in LP57 (1 M LiPF 6 in 3:7 ethylene carbonate (EC)/ethyl methyl carbonate (EMC)) is solvent viscosity, rather than ion aggregation or cation transference number. We find that ion association decreases with decreasing temperature, while the cation transference number is positive and roughly independent of temperature. In an effort to improve low temperature performance, we introduce γ -butyrolactone (GBL) as a low viscosity co-solvent to explore two alternative formulations: 1 M LiPF 6 in 15:15:70 EC/GBL/EMC and 3:7 GBL/EMC. While GBL reduces solution viscosity, its low dielectric constant results in increased ion pairing, yielding neither improved bulk ionic conductivity nor appreciably altered ion transport mechanisms. We expect that these results will enhance understanding of low temperature transport and inform the development of superior electrolytes.

25 ENERGY STORAGE↗
NASA NTRS2002

High Temperature Transfer Molding Resins Based on 2,3,3',4'-Biphenyltetracarboxylic Dianhydride

As part of an ongoing effort to develop materials for resin transfer molding (RTM) processes to fabricate high performance/high temperature composite structures, phenylethynyl containing imides have been under investigation. New phenylethynyl containing imide compositions were prepared using 2,3,3',4'-biphenyltetracarboxylic dianhydride (a-BPDA) and evaluated for cured glass transition temperature (Tg), melt flow behavior, and for processability into flat composite panels via RTM. The a-BPDA imparts a unique combination of properties that are desirable for high temperature transfer molding resins. In comparison to its symmetrical counterpart (i.e. 3,3',4,4'-biphenyltetracarboxylic dianhydride), a-BPDA affords oligomers with lower melt viscosities and when cured, higher Tgs. Several candidates exhibited the appropriate combination of properties such as a low and stable melt viscosity required for RTM processes, high cured Tg, and moderate toughness. The chemistry, physical, and composite properties of select resins will be discussed.

Smith, J. G., Jr.↗
NASA NTRS1999

Viscosity of Xenon Examined in Microgravity

Why does water flow faster than honey? The short answer, that honey has a greater viscosity, merely rephrases the question. The fundamental answer is that viscosity originates in the interactions between a fluid s molecules. These interactions are so complicated that, except for low-density gases, the viscosity of a fluid cannot be accurately predicted. Progress in understanding viscosity has been made by studying moderately dense gases and, more recently, fluids near the critical point. Modern theories predict a universal behavior for all pure fluids near the liquid-vapor critical point, and they relate the increase in viscosity to spontaneous fluctuations in density near this point. The Critical Viscosity of Xenon (CVX) experiment tested these theories with unprecedented precision when it flew aboard the Space Shuttle Discovery (STS-85) in August 1997. Near the critical point, xenon is a billion times more compressible than water, yet it has about the same density. Because the fluid is so "soft," it collapses under its own weight when exposed to the force of Earth s gravity - much like a very soft spring. Because the CVX experiment is conducted in microgravity, it achieves a very uniform fluid density even very close to the critical point. At the heart of the CVX experiment is a novel viscometer built around a small nickel screen. An oscillating electric field forces the screen to oscillate between pairs of electrodes. Viscosity, which dampens the oscillations, can be calculated by measuring the screen motion and the force applied to the screen. So that the fluid s delicate state near the critical point will not be disrupted, the screen oscillations are set to be both slow and small.

Zimmerli, Gregory A.↗
NASA NTRS1995

On Lateral Viscosity Contrast in the Mantle and the Rheology of Low-Frequency Geodynamics

Mantle-wide heterogeneity is largely controlled by deeply penetrating thermal convective currents. These thermal currents are likely to produce significant lateral variation in rheology, and this can profoundly influence overall material behaviour. How thermally related lateral viscosity variations impact models of glacio-isostatic and tidal deformation is largely unknown. An important step towards model improvement is to quantify, or bound, the actual viscosity variations that characterize the mantle. Simple scaling of viscosity to shear-wave velocity fluctuations yields map-views of long- wavelength viscosity variation. These give a general quantitative description and aid in estimating the depth dependence of rheological heterogeneity throughout the mantle. The upper mantle is probably characterized by two to four orders of magnitude variation (peak-to-peak). Discrepant time-scales for rebounding Holocene shorelines of Hudson Bay and southern Iceland are consistent with this characterization. Results are given in terms of a local average viscosity ratio, (Delta)eta(bar)(sub i), of volumetric concentration, phi(sub i). For the upper mantle deeper than 340 km the following reasonable limits are estimated for (delta)eta(bar) approx. equal 10(exp -2): 0.01 less than or equal to phi less than or equal to 0.15. A spectrum of ratios (Delta)eta(bar)(sub i) less than 0.1 at concentration level eta(sub i) approx. equal 10(exp -6) - 10(exp -1) in the lower mantle implies a spectrum of shorter time-scale deformational response modes for second-degree spherical harmonic deformations of the Earth. Although highly uncertain, this spectrum of spatial variation allows a purely Maxwellian viscoelastic rheology simultaneously to explain all solid tidal dispersion phenomena and long-term rebound-related mantle viscosity. Composite theory of multiphase viscoelastic media is used to demonstrate this effect.

Ivins, Erik R.↗
DOE OSTI2022

Optimization of matrix viscosity improves polypropylene fiber dispersion and properties of engineered cementitious composites

Engineered cementitious composites (ECC) is a durable cementitious material with high tensile ductility and strain-hardening characteristics. Although considered as a cost-effective fiber for ECC, polypropylene (PP) fiber is reportedly difficult to disperse in mortar matrix due to its high aspect ratio and hydrophobicity. In this study, the matrix viscosity of a low-carbon ECC based on limestone calcined clay cement was tailored as a variable to improve PP fiber dispersion under a pre-determined mixing protocol. The effect of matrix viscosity on the composite fresh and hardened properties was investigated experimentally. Results suggested an optimal range of matrix viscosity (10.3–11.5 Pa . s) favors the composite tensile strength and strain capacity at 28 days. At the optimal state with a 0.1 % viscosity modifying admixture (VMA)-to-binder mass ratio, PP-ECC achieved 7.0 % tensile strain capacity and 3.5 MPa ultimate tensile strength. When matrix viscosity falls outside the desired range, both ultimate tensile strength and strain capacity were diminished. By tailoring the VMA dosage, the matrix viscosity can be adjusted for desired fiber dispersion, workability, and mechanical properties. Finally, the findings of this study provide a technical reference for the practical design and application of PP-ECC.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Seismic velocity, attenuation and rheology of the upper mantle

Seismic and rheological properties of the upper mantle in the vicinity of the low-velocity zone are expressed in terms of relaxation by dislocation glide. Dislocation bowing in the glide plane explains seismic velocities and attenuation. Climbing at higher stresses for longer periods of time give the observed viscosity, and explain the low velocity and high temperature attenuation found at seismic frequencies. Due to differing parameters, separate terms for thermal, seismic and rheological lithospheres are proposed. All three lithospheres, however, are related and are functions of temperature, and must be specified by parameters such as period, stress, and stress duration.

Anderson, D. L.↗