Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter sweep”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Bright tunable femtosecond x-ray emission from laser irradiated micro-droplets

It is demonstrated that bright femtosecond X-rays can be obtained by irradiating a moderate laser onto a helium micro-droplet. The laser ponderomotive force continuously sweeps electrons from the droplets and accelerates them forward. The electrons exposed in the outrunning laser field oscillate transversely and emit photons in the forward direction. The total flux of photons with energies above 1 keV is as high as 10{sup 9}/shot which is about 10-fold enhancement compared with betatron oscillation under similar laser conditions. The maximum achieved peak brightness is up to 10{sup 21} photons/s/mm{sup 2}/mrad{sup 2}/0.1%BW. By adjusting laser and droplet parameters, we can get tunable X-rays with required brightness and energy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Measurements of fission gas release from nuclear fuel in support of BISON fuel performance analysis

This project established a fuel irradiation and fission gas release (FGR) loop that has been designed for implementation at the PULSTAR reactor of North Carolina State University (NCSU). The FGR loop is capable of analyzing various types of fuel samples including, e.g., uranium dioxide fuel (UO 2 ) and uranium silicide (U 3 Si 2 ) samples. The fuel samples were produced and characterized at Idaho National Laboratory (INL) and shipped NCSU. The samples are ready for irradiation in the FGR loop to a given total thermal neutron fluence and under controlled temperature conditions. An innovative high resolution gamma-ray spectrometry approach and instrumentation have been established to monitor the loop’s sweep gas and perform high accuracy measurements of the gas release rates relative to predicted birth rates to establish the release-to-birth ratio (R/B) for a given radionuclide. In addition, uncertainty minimization is achieved through the formulation of the measurement observables into relative release-to-birth indicators for selected radionuclides. The experimental findings will be utilized to enhance and validate the fission gas release models that are currently implemented in the BISON fuel performance code. The experimentally deduced physical parameters will be incorporated in BISON’s fission gas release models. Atomistic simulations of fuel behavior have been performed to investigate the mechanisms of fission gas migration in the fuel. At this stage, performance of the fuel irradiation experiments awaits licensing approval by the US NRC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Integrated Aerodynamic and Control System Design of Oblique Wing Aircraft

An efficient high speed aircraft design must achieve a high lift to drag ratio at transonic and supersonic speeds. In 1952 Dr. R. T. Jones proved that for any flight Mach number minimum drag at a fixed lift is achieved by an elliptic wing planform with an appropriate oblique sweep angle. Since then, wind tunnel tests and numerical flow models have confirmed that the compressibility drag of oblique wing aircraft is lower than similar symmetrical sweep designs. At oblique sweep angles above thirty degrees the highly asymmetric planform gives rise to aerodynamic and inertia couplings which affect stability and degrade the aircraft's handling qualities. In the case of the NASA-Rockwell Oblique Wing Research Aircraft, attempts to improve the handling qualities by implementing a stability augmentation system have produced unsatisfactory results because of an inherent lack of controllability in the proposed design. The present work focuses on improving the handling qualities of oblique wing aircraft by including aerodynamic configuration parameters as variables in the control system synthesis to provide additional degrees of freedom with which to further decouple the aircraft's response. Handling qualities are measured using a quadratic cost function identical to that considered in optimal control problems, but the controller architecture is not restricted to full state feedback. An optimization procedure is used to simultaneously solve for the aircraft configuration and control gains which maximize a handling qualities measure, while meeting imposed constraints on trim. In some designs wing flexibility is also modeled and reduced order controllers are implemented. Oblique wing aircraft synthesized by this integrated design method show significant improvement in handling qualities when compared to the originally proposed closed loop aircraft. The integrated design synthesis method is then extended to show how handling qualities may be traded for other types of mission performance (drag, weight, etc.). Examples are presented which show how performance can be maximized while maintaining a desired level of handling quality.

Morris, Stephen James↗

Optimized Flow Sheet for a Reference Commercial-Scale Nuclear-Driven High-Temperature Electrolysis Hydrogen Production Plant

This report presents results from the development and optimization of a reference commercialscale high-temperature electrolysis (HTE) plant for hydrogen production. The reference plant design is driven by a high-temperature helium-cooled reactor coupled to a direct Brayton power cycle. The reference design reactor power is 600 MWt, with a primary system pressure of 7.0 MPa, and reactor inlet and outlet fluid temperatures of 540° C and 900°C, respectively. The electrolysis unit used to produce hydrogen consists of 4.176 × 10 6 cells with a per-cell active area of 225 cm2. A nominal cell area-specific resistance, ASR, value of 0.4 Ohm•cm2 with a current density of 0.25 A/cm2 was used, and isothermal boundary conditions were assumed. The optimized design for the reference hydrogen production plant operates at a system pressure of 5.0 MPa, and utilizes an air-sweep system to remove the excess oxygen that is evolved on the anode side of the electrolyzer. The inlet air for the air-sweep system is compressed to the system operating pressure of 5.0 MPa in a four-stage compressor with intercooling. The overall system thermal-to-hydrogen production efficiency (based on the low heating value of the produced hydrogen) is 49.07% at a hydrogen production rate of 2.45 kg/s with the high-temperature helium-cooled reactor concept. The information presented in this report is intended to establish an optimized design for the reference nuclear-driven HTE hydrogen production plant so that parameters can be compared with other hydrogen production methods and power cycles to evaluate relative performance characteristics and plant economics.

08 HYDROGEN↗

A Summary of Flight-Determined Transonic Lift and Drag Characteristics of Several Research Airplane Configurations

Flight-determined lift and drag data from transonic flights of seven research airplane configurations of widely varying characteristics are presented and compared with wind-tunnel and rocket-model data. The airplanes are the X-5 (590 wing sweep), XF-92A, YF-102 with cambered wing, YF-102 with symmetrical wing, D-558-ii, X-3, and X-LE. The effects of some of the basic configuration differences on the lift and drag characteristics are demonstrated. As indicated by transonic similarity laws, most of the configurations demonstrate a relationship between the transonic increase in zero-lift drag and the maximum cross-sectional area. No such relationship was found between the drag-rise Mach number and its normally related parameters. A comparison of flight and wind-tunnel data shows a generally reasonable agreement, but Reynolds number differences can cause considerable variations in the drag levels of the flight and wind-tunnel tests. Maximum lift-drag ratios vary widely in the subsonic region as would be expected from differences in aspect ratio and wing thickness ratio; however, the variations diminish as the Mach number is increased through the transonic region. The attainment of maximum lift-drag ratio in level flight by several of the airplanes was limited by engine performance, stability characteristics, and buffet boundaries.

Bellman, Donald R.↗

Stability and Control CFD Investigations of a Generic 53 Degree Swept UCAV Configuration

NATO STO Task Group AVT-201 on "Extended Assessment of Reliable Stability & Control Prediction Methods for NATO Air Vehicles" is studying various computational approaches to predict stability and control parameters for aircraft undergoing non-linear flight conditions. This paper contributes an assessment through correlations with wind tunnel data for the state of aerodynamic predictive capability of time-accurate RANS methodology on the group's focus configuration, a 53deg swept and twisted lambda wing UCAV, undergoing a variety of roll, pitch, and yaw motions. The vehicle aerodynamics is dominated by the complex non-linear physics of round leading-edge vortex flow separation. Correlations with experimental data are made for static longitudinal/lateral sweeps, and at varying frequencies of prescribed roll/pitch/yaw sinusoidal motion for the vehicle operating with and without control surfaces. The data and the derived understanding should prove useful to the AVT-201 team and other researchers who are developing techniques for augmenting flight simulation models from low-speed CFD predictions of aircraft traversing non-linear regions of a flight envelope.

Frink, Neal T.↗

COMPONENT DEVELOPMENT NEEDS FOR THE HYBRID SULFUR ELECTROLYZER

Fiscal year 2008 studies in electrolyzer component development have focused on the characterization of membrane electrode assemblies (MEA) after performance tests in the single cell electrolyzer, evaluation of electrocatalysts and membranes using a small scale electrolyzer and evaluating the contribution of individual cell components to the overall electrochemical performance. Scanning electron microscopic (SEM) studies of samples taken from MEAs testing in the SRNL single cell electrolyzer test station indicates a sulfur-rich layer forms between the cathode catalyst layer and the membrane. Based on a review of operating conditions for each of the MEAs evaluated, we conclude that the formation of the layer results from the reduction of sulfur dioxide as it passes through the MEA and reaches the catalyst layer at the cathode-membrane interface. Formation of the sulfur rich layer results in partial delamination of the cathode catalyst layer leading to diminished performance. Furthermore we believe that operating the electrolyzer at elevated pressure significantly increases the rate of formation due to increased adsorption of hydrogen on the internal catalyst surface. Thus, identification of a membrane that exhibits much lower transport of sulfur dioxide is needed to reduce the quantity of sulfur dioxide that reaches the cathode catalyst and is reduced to produce the sulfur-rich layer. Three candidate membranes are currently being evaluated that have shown promise from preliminary studies, (1) modified Nafion{reg_sign}, (2) polybenzimidazole (PBI), and (3) sulfonated Diels Alder polyphenylene (SDAPP). Testing examined the activity for the sulfur dioxide oxidation of platinum (Pt) and platinum-alloy catalysts in 30 wt% sulfuric acid solution. Linear sweep voltammetry showed an increase in activity when catalysts in which Pt is alloyed with non-noble transition metals such as cobalt and chromium. However when Pt is alloyed with noble metals, such as iridium or ruthenium, the kinetic activity decreases. We recommend further testing to determine if these binary alloys will provide the increased reaction kinetic needed to meet the targets. We also plan to test the performance of these catalyst materials for both proton and sulfur dioxide reduction. The latter may provide another parameter by which we can control the reduction of sulfur dioxide upon transport to the cathode catalyst surface. A small scale electrolyzer (2 cm{sup 2}) has been fabricated and successfully installed as an additional tool to evaluate the effect of different operating conditions on electrolyzer and MEA performance. Currently this electrolyzer is limited to testing at temperatures up to 80 C and at atmospheric pressure. Selected electrochemical performance data from the single cell sulfur dioxide depolarized electrolyzer were analyzed with the aid of an empirical equation which takes into account the overpotential of each of the components. By using the empirical equation, the performance data was broken down into its components and a comparison of the potential losses was made. The results indicated that for the testing conditions of 80 C and 30 wt% sulfuric acid, the major overpotential contribution ({approx}70 % of all losses) arise from the slow reaction rate of oxidation of sulfur dioxide. The results indicate that in order to meet the target of hydrogen production at 0.5 A/cm{sup 2} at 0.6 V and 50 wt% sulfuric acid, identification of a better catalyst for sulfur dioxide oxidation will provide the largest gain in electrolyzer performance.

08 HYDROGEN↗

Target normal sheath acceleration with a large laser focal diameter

In this work, the dependence of the laser-driven ion acceleration from thin titanium foils in the Target Normal Sheath Acceleration (TNSA) regime on target and laser parameters is explored using two dimensional particle-in-cell simulations. The oblique incidence (θ L = 45°) and large focal spot size (w 0 = 40μm) are chosen to take an advantage of quasi one-dimensional geometry of sheath fields and effective electron heating. This interaction setup also reveals low and achromatic angular divergence of a proton beam. It is shown that the hot electron temperature deviates from the ponderomotive scaling for short laser pulses and small pre-plasmas. This deviation is mainly due to the laser sweeping, as the short duration laser pulse each moment in time effectively heats only a fraction of a focal spot on the foil. This instantaneous partial heating results in an electron temperature deviation from the ponderomotive scaling and, thus, lower maximum proton energies than it could have been expected from the TNSA theory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermal Stability of Schottky Contacts and Rearrangement of Defects in β ‐Ga 2 O 3 Crystals

Abstract The thermal stability of different Schottky contacts (Au, Pt, and Ni) on (100) β ‐Ga 2 O 3 single crystals grown by the Czochralski method is investigated. Besides the examination of the Schottky barrier parameters, contact‐dependent defect levels are investigated by deep‐level transient spectroscopy (DLTS) in a 100–650 K (ramp‐up) and 650–100 K (ramp‐down) temperature cycle. Several defect levels are detected below the conduction band minimum at 0.41, 0.60, 0.77, 0.96, and 1.17 eV. In the temperature ramp‐down DLTS, the 1.17 eV level disappears, and the 0.60 eV level appears for all Schottky contacts. DFT calculations suggest that rearrangement and dissociation of a single hydrogen from a doubly‐hydrogenated Ga─O divacancy complex occurs during the temperature sweep under bias. The trap level at 0.96 eV only appears after the thermal load for the Ni contact, in contrast to Au and Pt, where it is present without a thermal budget. Temperature‐dependent leakage current (at −4 V) measurements indicate oxidation of Ni, and further thermodynamic analysis suggests alloying of Au‐Ga atoms at the Au/ β ‐Ga 2 O 3 interface. These studies provide insight into the behavior induced by these common Schottky contacts and the alteration associated with temperature cycling.

36 MATERIALS SCIENCE↗

Vortex instabilities in 3D boundary layers: The relationship between Goertler and crossflow vortices

The inviscid and viscous stability problems are addressed for a boundary layer which can support both Goertler and crossflow vortices. The change in structure of Goertler vortices is found when the parameter representing the degree of three-dimensionality of the basic boundary layer flow under consideration is increased. It is shown that crossflow vortices emerge naturally as this parameter is increased and ultimately become the only possible vortex instability of the flow. It is shown conclusively that at sufficiently large values of the crossflow there are no unstable Goertler vortices present in a boundary layer which, in the zero crossflow case, is centrifugally unstable. The results suggest that in many practical applications Goertler vortices cannot be a cause of transition because they are destroyed by the 3-D nature of the basic state. In swept wing flows the Goertler mechanism is probably not present for typical angles of sweep of about 20 degrees. Some discussion of the receptivity problem for vortex instabilities in weakly 3-D boundary layers is given; it is shown that inviscid modes have a coupling coefficient marginally smaller than those of the fastest growing viscous modes discussed recently by Denier, Hall, and Seddougui (1990). However the fact that the growth rates of the inviscid modes are the largest in most situations means that they are probably the most likely source of transition.

Bassom, Andrew↗

35-45 Giga Hertz Transceiver System for Phase and Magnitude Detection

Nondestructive evaluation (NDE) is the science and practice of examining an object in a way that the object's usefulness is not adversely affected. Different types of NDE methods exist but this thesis is based on microwave and millimeter wave NDE using imaging techniques. Microwave NDE is based on illuminating the object under test with a microwave signal and studying the various properties of the reflected signal from the object. This reflected signal contains some information about the inner structure of the object under test. This information may be contained in several parameters including the phase and magnitude of the reflected signal. The goal of this project is to design and build a Q-band coherent transceiver that is capable of measuring the reflected signal's phase and magnitude so that an image of the object under test may be reconstructed. From the several techniques that can be used to construct an image of the object under test, techniques of interest to this work include synthetic aperture focusing technique (SAFT) and microwave holography. The transceiver system should have the ability to sweep a large portion of Q-band frequency range in small frequency steps as quick as possible while the detected phase and magnitude of the reflected signal is very accurate. Several different designs were studied and the final schematic diagram of the transceiver system was determined. One of the most important modules that was designed, implemented and tested in the laboratory was an accurate phase/magnitude detector circuit. The compared results of the scans using the transceiver system and vector network analyzer (VNA) showed that this transceiver system has a great potential to replace a VNA for the purpose of microwave and millimeter wave imaging.

Beni, Aman Aflaki↗

Synthesis and characterization of high-photoactivity electrodeposited Cu{sub 2}O solar absorber by photoelectrochemistry and ultrafast spectroscopy.

We present a systematic study on the effects of electrodeposition parameters on the photoelectrochemical properties of Cu{sub 2}O. The influence of deposition variables (temperature, pH, and deposition current density) on conductivity has been widely explored in the past for this semiconductor, but the optimization of the electrodeposition process for the photoelectrochemical response in aqueous solutions under AM 1.5 illumination has received far less attention. In this work, we analyze the photoactivity of Cu{sub 2}O films deposited at different conditions and correlate the photoresponse to morphology, film orientation, and electrical properties. The photoelectrochemical response was measured by linear sweep voltammetry under chopped simulated AM 1.5 illumination. The highest photocurrent obtained was -2.4 mA cm{sup -2} at 0.25 V vs RHE for a film thickness of 1.3 {micro}m. This is the highest reported value reached so far for this material in an aqueous electrolyte under AM 1.5 illumination. The optical and electrical properties of the most photoactive electrode were investigated by UV-vis spectroscopy and electrochemical impedance, while the minority carrier lifetime and diffusion length were measured by optical-pump THz-probe spectroscopy.

14 SOLAR ENERGY↗

Influences of lidar scanning parameters on wind turbine wake retrievals in complex terrain

Abstract. Scanning lidars enable the collection of spatially distributed measurements of turbine wakes and the estimation of wake properties such as magnitude, extent, and trajectory. Lidar-based characterizations, however, may be subject to distortions due to the observational system. Distortions can arise from the resolution of the measurement points across the wake, the projection of the winds onto the beam, averaging along the beam probe volume, and intervening evolution of the flow over the scan duration. Using a large-eddy simulation and simulated measurements with a virtual lidar model, we assess how scanning lidar systems may influence the properties of the retrieved wake using a case study from the Perdigão campaign. We consider three lidars performing range-height indicator sweeps in complex terrain, based on the deployments of lidars from the Danish Technical University (DTU) and German Aerospace Center (DLR) at the Perdigão site. The unwaked flow, measured by the DTU lidar, is well-captured by the lidar, even without combining data into a multi-lidar retrieval. The two DLR lidars measure a waked transect from different downwind vantage points. In the region of the wake, the observation system reacts to the smaller spatial and temporal variations of the winds, allowing more significant observation distortions to arise. While the measurements largely capture the wake structure and trajectory over its 4–5 D extent, limited spatial resolution of measurement points and volume averaging lead to a quicker loss of the two lobes in the near wake, smearing of the vertical bounds of the wake (< 30 m), wake center displacements up to 10 m, and dampening of the maximum velocity deficit by up to a third. The virtual lidar tool, coupled with simulations, provides a means for assessing measurement capabilities in advance of measurement campaigns.

17 WIND ENERGY↗

Tuning of strong nonlinearity in radio-frequency superconducting-quantum-interference-device meta-atoms

Strong nonlinearity of a self-resonant radio-frequency (rf) superconducting-quantum-interference-device (SQUID) meta-atom is explored via intermodulation (IM) measurements. Previous work in zero dc magnetic flux showed a sharp onset of IM response as the frequency sweeps through the resonance. A second onset at higher frequency was also observed, creating a prominent gap in the IM response. By extending those measurements to nonzero dc flux, different dynamics are revealed, including dc flux tunability of the aforementioned gaps and enhanced IM response near geometric resonance of the rf SQUID. These features observed experimentally are understood and analyzed theoretically through a combination of a steady-state analytical modeling and a full numerical treatment of the rf SQUID dynamics. The latter in addition predicts the presence of chaos in narrow parameter regimes. Here, the understanding of intermodulation in rf SQUID metamaterials is important for producing low-noise amplification of microwave signals and tunable filters.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

GALSPEC: A Tool for Computing the Spectra of Star-Forming Galaxies of Low Metallicity

The far-ultraviolet spectral region is rich in diagnostics of star formation in galaxies; it gives information not only about the star-forming complex, but also about the dust and circumstellar gas. We have therefore developed a tool, called GALSPEC, for computing far-UV spectra of star-forming galaxies. The user controls the process through a graphical user interface (GUI) by specifying the input parameters for the stars, dust, and gas. GALSPEC computes the integrated spectrum of a star-forming complex, given the rate of star formation, metallicity (0.2 Z(sub \odot) or 0.5 Z(sub \odot)), and IMF upper mass limit. To compute the integrated spectrum, GALSPEC makes use of a library of stellar spectra composed of observed spectra from HST and model spectra calculated with the TLUSTY/SYNSPEC program (Hubeny & Lanz 1995). GALSPEC then applies wavelength-dependent extinction according to Calzetti's starburst extinction law. The mechanical luminosity from massive stars and supernovae sweeps up interstellar material thereby forming an expanding shell with a central cavity. GALSPEC computes the absorption spectrum of the shell using the CLOUDSPEC program (Hubeny 2000), a combination of Ferland's CLOUDY program and SYNSPEC.

Heap, S. R.↗

Inlet Vortex Generator Design for the X-59 Low Boom Flight Demonstrator

An array of vortex generators was designed for the X-59 Low Boom Flight Demonstrator aircraft inlet. Prior to the a High Speed Inlet DistortionTest, concern regarding potentially high measurements of steady state or dynamic distortion prompted an effort to examine the use of passive flow control to reduce distortion levels. Design of experiments methodology was used to develop two matrices of vortex generators placed inside the inlet serpentine duct and upstream of the inlet on the compression surface, varying on several geometric parameters. Reynolds- Averaged Navier-Stokes simulations were performed using the FUN3D flow solver at Mach 1.45 to analyze the impact of each configuration on total pressure recovery, circumferential distortion, and radial distortion. Results fromsimulations of the baseline aircraft are compared with data acquired in the NASA Glenn Research Center’s 8- by 6-foot SupersonicWind Tunnel. A vortex generator configuration with vanes placed upstream of the inlet terminal shock was shown to significantly increase total pressure recovery and decrease circumferential distortion with no penalty to radial distortion levels. Inlet mass flow sweeps at Mach 1.45, 0.6, and 0.3 indicated no detrimental effects from the vanes at off-design conditions.

Vortex generators↗

Source Diagnostic Fan II (22-inch) Duct Mode Characteristics as Measured by the Rotating Rake Mode Measurement System while Operated in the NASA Glenn 9x15 Low Speed Wind Tunnel

The second entry of the Source Diagnostic Test (SDT2) was a continuation of the first SDT entry with additional parameters tested. The rotor, stators, and general flow path hardware used in SDT2 were the same as those for SDT1. This included a radial baseline set of stator vanes, which had a vane count such that the rotor-stator interaction at the fan blade passing fundamental was cut-off, as is typical for modern turbofans. Two sets of stator vanes were designed and tested with a count generating a cut-on rotor-stator interaction at the fan blade passing fundamental. One of the sets maintained the no aerodynamic sweep as the radial baseline, the other was designed with leading edge sweep with the intent to generate lower noise. The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present. The system is a radial rake immersed into the duct that continuously rotates about the duct centerline. For each of the three stator vane configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator interaction mode acoustic levels. Multiple-pure tones generated by the M5 rotor in the inlet were also measured.

Turbofan, Duct Modes↗

Source Diagnostic Fan II (22-inch) Duct Mode Characteristics as Measured by the Rotating Rake Mode Measurement System while Operated in the NASA Glenn 9x15 Low Speed Wind Tunnel

The second entry of the Source Diagnostic Test (SDT2) was a continuation of the first SDT entry with additional parameters tested. The rotor, stators, and general flow path hardware used in SDT2 were the same as those for SDT1. This included a radial baseline set of stator vanes, which had a vane count such that the rotor-stator interaction at the fan blade passing fundamental was cut-off, as is typical for modern turbofans. Two sets of stator vanes were designed and tested with a count generating a cut-on rotor-stator interaction at the fan blade passing fundamental. One of the sets maintained the no aerodynamic sweep as the radial baseline, the other was designed with leading edge sweep with the intent to generate lower noise. The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present. The system is a radial rake emersed into the duct that continuously rotates about the duct centerline. For each of the three stator vane configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator interaction mode acoustic levels. Multiple-pure tones generated by the M5 rotor in the inlet were also measured.

Turbofan↗