SEARCH · Search NASA

Results for “perturbation test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Upper mass limits for stable rotating white dwarfs

Models of nonmagnetic axisymmetric differentially rotating zero-temperature white dwarfs are constructed and tested for stability. Upper mass limits, beyond which models become secularly and dynamically unstable to growth of nonaxisymmetric perturbations, are found at 2.5 solar masses and 4.6 solar masses, respectively. The upper mass limit for secular stability is practically the same for the two angular momentum distributions considered. Crude growth rates due to gravitational radiation and degenerate-electron viscosity are calculated for the secularly unstable models. Except for a narrow parameter range, gravitational radiation is the dominant destabilizing mechanism. For masses between 3.5 and 4.6 solar masses, the secular instability grows on a time scale of about 10 to 1000 years; for masses exceeding about 4.6 solar masses, the dynamic instability grows on a time scale of seconds. Implications of these results for mass-transfer binary star systems and degenerate stellar cores are discussed.

Durisen, R. H.↗

NASA NTRS1977

A practical method for correcting bidirectional reflectance variations

The purpose of the investigation was to analyze angular bidirectional reflectance variations and to test the hypothesis that first order variations could be described from a consideration of shadows created by surface perturbations. The results demonstrate the validity of this approach, and while it is not suitable for calculating absolute spectral reflectance characteristics, the development of such a model was not the objective of the investigation. Instead, a model was needed which can make relative angular corrections to bidirectional reflectance measurements independent of the details of surface geometry.

Egbert, D. D.↗

NASA NTRS1980

A dynamic analysis of the motion of a low-wing general aviation aircraft about its calculated equilibrium flat spin mode

The properties of the flat spin mode of a general aviation configuration have been studied through analysis of rotary balance data, numerical simulation, and analytical study of the equilibrium state. The equilibrium state is predicted well from rotary balance data. The variations of yawing moment and pitching moment as functions of sideslip have been shown to be of great importance in obtaining accurate modeling. These dependencies are not presently available with sufficient accuracy from previous tests or theories. The stability of the flat spin mode has been examined extensively using numerical linearization, classical perturbation methods, and reduced order modeling. The stability exhibited by the time histories and the eigenvalue analyses is shown to be strongly dependent on certain static cross derivatives and more so on the dynamic derivatives. Explicit stability criteria are obtained from the reduced order models.

Tischler, M. B.↗

NASA NTRS1983

Quasi-relativistic electron precipitation due to interactions with coherent VLF waves in the magnetosphere

The equations of motion for the cyclotron resonance interaction between coherent whistler mode waves and energetic particles are rederived with the inclusion of relativistic effects. The pitch angle scattering of the near-loss-cone quasi-relativistic electrons trapped in the magnetosphere is studied using a test particle method employing these relativistic equations, and the precipitated energy spectrum due to the wave-induced perturbations of a full distribution of particles is computed. Results show that the full width at half maximum peak width of the rms scattering pattern of the near-loss-cone particles would give an upper bound to the peak width of the associated precipitated energy spectrum under the conditions of moderate wave intensities in the low L shell region. In addition, it is found that the peak widths are within the upper limit values measured by recent satellite experiments. It is concluded that interactions of inner radiation belt particles with monochromatic waves could produce precipitated fluxes with relatively sharp spectral widths, and that therefore the L-dependent narrow peaks observed by low altitude satellite particle detectors could be caused by such interactions.

Chang, H. C.↗

NASA NTRS1994

The Local Supercluster as a test of cosmological models

The Local Supercluster kinematic properties (the Local Group infall toward the Virgo Cluster and galaxy density distribution about the Virgo Cluster) in various cosmological models are examined utilizing large-scale N-body (PM) simulations 500(exp 3) cells, 250(exp 3) particles, and box size of 400 h(exp -1) Mpc) and are compared to observations. Five models are investigated: (1) the standard, Cosmic Background Explorer Satellite (COBE)-normalized cold dark matter (CDM) model with omega = 1, h = 0.5, and sigma(sub 8) = 1.05; (2) the standard Hot Dark Matter (HDM) model with omega = 1, h = 0.75, and sigma(sub 8) = 1; (3) the tilted CDM model with omega = 1, h = 0.5, n = 0.7, and sigma(sub 8) = 0.5; (4) a CDM + lambda model with omega = 0.3, lambda = 0.7, h = 2/3, and sigma(sub 8) = 2/3; (5) the PBI model with omega = 0.2, h = 0.8, x = 0.1, m = -0.5, and sigma(sub 8) = 0.9. Comparison of the five models with the presently available observational measurements v(sub LG) = 85 - 305 km/s (with mean of 250 km/s), delta(n(sub g))/(n(sub g)-bar) = 1.40 + or - 0.35) suggests that an open universe with omega approximately 0.5 (with or without lambda) and sigma(sub 8) approximately 0.8 is preferred, with omega = 0.3-1.0 (with or without lambda) and sigma(sub 8) = 0.7-1.0 being the acceptable range. At variance with some previous claims based on either direct N-body or spherical nonlinear approaches, we find that a flat model with sigma(sub 8) approximately 0.7-1.0 seems to be reasonably consistent with observations. However, if one favors the low limit of v(sub LG) = 85 km/s, then an omega approximately 0.2-0.3 universe seems to provide a better fit, and flat (omega = 1) models are ruled out at approximately 95% confidence level. On the other hand, if the high limit of v(sub LG) = 350 km/s is closer to the truth, then it appears that omega approximately 0.7-0.8 is more consistent. This test is insensitive to the shape of the power spectrum, but rather sensitive to the normalization of the perturbation amplitude on the relevant scale (e.g., sigma(sub 8)) and omega. We find that neither linear nor nonlinear relations (with spherical symmetry) are good approximations for the relation between radial peculiar velocity and density perturbation, i.e., nonspherical effects and gravitational tidal field are important. The derived omega using either of the two relations is underestimated. In some cases, this error is as large as a factor of 2-4.

Cen, Renyue↗

NASA NTRS2001

Asymmetry Effects in Numerical Simulation of Supersonic Flows with Upstream Separated Regions

The present paper studies the numerical simulation of flows with shock/boundary-layer upstream interaction, under conditions of symmetry in geometry, boundary conditions, and grid. For this purpose, a series of two- and three-dimensional numerical test-cases were carried out. The tests showed that standard numerical schemes, which appear to be symmetry preserving under most flow configurations, produce nonsymmetric perturbations when large separated regions are present. These perturbations are amplified when the core flow is under compression. If the flow-blockage due to separation is sufficiently large, the symmetry of the flow may collapse altogether. Experimental evidence of this numerical behavior is also considered.

Riodriguez, C. G.↗

NASA NTRS2009

Comparison of Node-Centered and Cell-Centered Unstructured Finite-Volume Discretizations: Viscous Fluxes - Part 1

Discretization of the viscous terms in current finite-volume unstructured-grid schemes are compared using node-centered and cell-centered approaches in two dimensions. Accuracy and efficiency are studied for six nominally second-order accurate schemes: a node-centered scheme, cell-centered node-averaging schemes with and without clipping, and cell-centered schemes with unweighted, weighted, and approximately mapped least-square face gradient reconstruction. The grids considered range from structured (regular) grids to irregular grids composed of arbitrary mixtures of triangles and quadrilaterals, including random perturbations of the grid points to bring out the worst possible behavior of the solution. Two classes of tests are considered. The first class of tests involves smooth manufactured solutions on both isotropic and highly anisotropic grids with discontinuous metrics, typical of those encountered in grid adaptation. The second class concerns solutions and grids varying strongly anisotropically over a curved body, typical of those encountered in high-Reynolds number turbulent flow simulations. Results from the first class indicate the face least-square methods, the node-averaging method without clipping, and the node-centered method demonstrate second-order convergence of discretization errors with very similar accuracies per degree of freedom. The second class of tests are more discriminating. The node-centered scheme is always second order with an accuracy and complexity in linearization comparable to the best of the cell-centered schemes. In comparison, the cell-centered node-averaging schemes are less accurate, have a higher complexity in linearization, and can fail to converge to the exact solution when clipping of the node-averaged values is used. The cell-centered schemes using least-square face gradient reconstruction have more compact stencils with a complexity similar to the complexity of the node-centered scheme. For simulations on highly anisotropic curved grids, the least-square methods have to be amended either by introducing a local mapping of the surface anisotropy or modifying the scheme stencil to reflect the direction of strong coupling.

Diskin, Boris↗

NASA NTRS2009

Method and system to perform energy-extraction based active noise control

A method to provide active noise control to reduce noise and vibration in reverberant acoustic enclosures such as aircraft, vehicles, appliances, instruments, industrial equipment and the like is presented. A continuous-time multi-input multi-output (MIMO) state space mathematical model of the plant is obtained via analytical modeling and system identification. Compensation is designed to render the mathematical model passive in the sense of mathematical system theory. The compensated system is checked to ensure robustness of the passive property of the plant. The check ensures that the passivity is preserved if the mathematical model parameters are perturbed from nominal values. A passivity-based controller is designed and verified using numerical simulations and then tested. The controller is designed so that the resulting closed-loop response shows the desired noise reduction.

Kelkar, Atul↗

NASA NTRS2010

Comparison of Node-Centered and Cell-Centered Unstructured Finite-Volume Discretizations: Viscous Fluxes

Discretization of the viscous terms in current finite-volume unstructured-grid schemes are compared using node-centered and cell-centered approaches in two dimensions. Accuracy and complexity are studied for four nominally second-order accurate schemes: a node-centered scheme and three cell-centered schemes - a node-averaging scheme and two schemes with nearest-neighbor and adaptive compact stencils for least-square face gradient reconstruction. The grids considered range from structured (regular) grids to irregular grids composed of arbitrary mixtures of triangles and quadrilaterals, including random perturbations of the grid points to bring out the worst possible behavior of the solution. Two classes of tests are considered. The first class of tests involves smooth manufactured solutions on both isotropic and highly anisotropic grids with discontinuous metrics, typical of those encountered in grid adaptation. The second class concerns solutions and grids varying strongly anisotropically over a curved body, typical of those encountered in high-Reynolds number turbulent flow simulations. Tests from the first class indicate the face least-square methods, the node-averaging method without clipping, and the node-centered method demonstrate second-order convergence of discretization errors with very similar accuracies per degree of freedom. The tests of the second class are more discriminating. The node-centered scheme is always second order with an accuracy and complexity in linearization comparable to the best of the cell-centered schemes. In comparison, the cell-centered node-averaging schemes may degenerate on mixed grids, have a higher complexity in linearization, and can fail to converge to the exact solution when clipping of the node-averaged values is used. The cell-centered schemes using least-square face gradient reconstruction have more compact stencils with a complexity similar to that of the node-centered scheme. For simulations on highly anisotropic curved grids, the least-square methods have to be amended either by introducing a local mapping based on a distance function commonly available in practical schemes or modifying the scheme stencil to reflect the direction of strong coupling. The major conclusion is that accuracies of the node centered and the best cell-centered schemes are comparable at equivalent number of degrees of freedom.

Diskin, Boris↗

NASA NTRS2012

Active Combustion Control for Aircraft Gas-Turbine Engines-Experimental Results for an Advanced, Low-Emissions Combustor Prototype

Lean combustion concepts for aircraft engine combustors are prone to combustion instabilities. Mitigation of instabilities is an enabling technology for these low-emissions combustors. NASA Glenn Research Center s prior activity has demonstrated active control to suppress a high-frequency combustion instability in a combustor rig designed to emulate an actual aircraft engine instability experience with a conventional, rich-front-end combustor. The current effort is developing further understanding of the problem specifically as applied to future lean-burning, very low-emissions combustors. A prototype advanced, low-emissions aircraft engine combustor with a combustion instability has been identified and previous work has characterized the dynamic behavior of that combustor prototype. The combustor exhibits thermoacoustic instabilities that are related to increasing fuel flow and that potentially prevent full-power operation. A simplified, non-linear oscillator model and a more physics-based sectored 1-D dynamic model have been developed to capture the combustor prototype s instability behavior. Utilizing these models, the NASA Adaptive Sliding Phasor Average Control (ASPAC) instability control method has been updated for the low-emissions combustor prototype. Active combustion instability suppression using the ASPAC control method has been demonstrated experimentally with this combustor prototype in a NASA combustion test cell operating at engine pressures, temperatures, and flows. A high-frequency fuel valve was utilized to perturb the combustor fuel flow. Successful instability suppression was shown using a dynamic pressure sensor in the combustor for controller feedback. Instability control was also shown with a pressure feedback sensor in the lower temperature region upstream of the combustor. It was also demonstrated that the controller can prevent the instability from occurring while combustor operation was transitioning from a stable, low-power condition to a normally unstable high-power condition, thus enabling the high-power condition.

DeLaat, John C.↗

DOE OSTI2021

Singling out modified gravity parameters and data sets reveals a dichotomy between Planck and lensing

ABSTRACT An important route to testing general relativity (GR) at cosmological scales is usually done by constraining modified gravity (MG) parameters added to the Einstein perturbed equations. Most studies have analysed so far constraints on pairs of MG parameters, but here, we explore constraints on one parameter at a time while fixing the other at its GR value. This allows us to analyse various models while benefiting from a stronger constraining power from the data. We also explore which specific data sets are in tension with GR. We find that models with (μ = 1, η) and (μ, η = 1) exhibit a 3.9σ and 3.8σ departure from GR when using Planck18 + Supernovae type Ia (SNe) + Baryon acoustic oscillation (BAO), while (μ, η) shows a tension of 3.4σ. We find no tension with GR for models with the MG parameter Σ fixed to its GR value. Using a Bayesian model selection analysis, we find that some one-parameter MG models are moderately favoured over ΛCDM when using all data set combinations except Planck cosmic microwave background lensing and dark energy survey data. Namely, Planck18 shows a moderate tension with GR that only increases when adding any combination of redshift space distortion, SNe, or BAO. However, adding lensing diminishes or removes these tensions, which can be attributed to the ability of lensing in constraining the MG parameter Σ. The two overall groups of data sets are found to have a dichotomy when performing consistency tests with GR, which may be due to systematic effects, lack of constraining power, or modelling. These findings warrant further investigation using more precise data from ongoing and future surveys.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2024

Conceptual Design of Neutron Sensor Qualification Device

The Advanced Sensors and Instrumentation Program at Idaho National Laboratory has been formulating strategies to qualify sensors for use in nuclear environments, particularly in irradiation experiments and advanced reactors. When qualifying neutron sensors for use in high-temperature environments, the wide range of neutron flux levels and representative energy spectra presents significant challenges. This paper discusses the development of the Neutron Sensor Qualification Device (NQD), which is designed to test neutron sensors in high temperature controlled environments with known neutron spectra, addressing the spatial and spectral complexities of neutron fluxes in reactor cores. The proposed NQD will be situated in the exposure room at the Armed Forces Radiobiology Research Institute, thus affording a unique capability to expose sensors to high neutron and gamma fluxes. To achieve thermal control, the device will utilize a radiation-hardened tube furnace, accommodating multiple sensors and neutron activation dosimetry wires. Titanium, iron, and cobalt dosimeter wires are chosen from the American Society for Testing and Materials and International Reactor Dosimetry and Fusion File libraries as references for providing energy-dependent fluence measurements. The design ensures precise sensor positioning to minimize mutual shielding and flux perturbation, which are evaluated via Monte Carlo N particle Transport Code (MCNP) simulations. These simulations have informed the development of guidelines on sensor placement within the NQD. The NQD is essential to the qualification of neutron sensors for advanced reactor technologies. It enables controlled testing of a statistically significant number of sensors, thereby supporting assessments of sensor performance across various neutron flux levels and temperatures. This paper highlights the detailed planning for the NQD prototype, along with its inaugural irradiation (scheduled for fiscal year [FY] 2025). The results from this initial testing will be fundamental in evaluating the device’s performance and establishing measurement uncertainty for in-pile neutron sensor measurements.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

NASA NTRS1997

Wave Driven Exothermic Heating in the Mesopause Region

A full-wave propagation model was developed that describes the propagation of gravity waves from the Earth's surface to the upper boundary, which can be placed anywhere between 150 and 500 km altitude. The model includes a realistic background atmosphere, and includes the effects of mean horizontal winds and their vertical shears, mean vertical temperature gradients, the eddy and molecular diffusion of heat and momentum, and the effects of ion-drag. This model solves five coupled second-order differential equations (continuity, momentum, and energy) in the vertical coordinate to derive the perturbation variables u', v', w' (horizontal and vertical velocity components), T' (temperature) and p' (pressure). The upper boundary can be automatically selected based on tests using the radiation condition at the upper boundary, wherein the height is increased until the wave is experiencing severe dissipation at the upper boundary, ensuring that substantial absorption occurs for any waves reflected from the upper boundary. The determination of wave amplitude is a key requirement of wave energetics. Therefore, the fullwave model has been applied to airglow observations in order to determine wave amplitudes as a function of altitude. This was accomplished by using the full-wave model output to drive a chemistry perturbation module that describes minor species perturbations and the resulting airglow perturbations. The full-wave output was multiplied by an altitude-independent factor such that the modeled and observed relative airglow intensity perturbations were equal. The effects of mean winds were included in these studies, and found to be the most important model input affecting the calculations (being more important than the choice of eddy diffusion profiles and chemical kinetic coefficients). In one study (Hickey et al., 1997a) these winds could not be well estimated from the measurements, whereas in the second study (Hickey et al.,1997b) the mean were well defined with a sodium wind-temperature lidar.

Hickey, Michael P.↗

NASA NTRS1999

Experimental and Numerical Optimization of a High-Lift System to Improve Low-Speed Performance, Stability, and Control of an Arrow-Wing Supersonic Transport

An investigation was performed to evaluate leading-and trailing-edge flap deflections for optimal aerodynamic performance of a High-Speed Civil Transport concept during takeoff and approach-to-landing conditions. The configuration used for this study was designed by the Douglas Aircraft Company during the 1970's. A 0.1-scale model of this configuration was tested in the Langley 30- by 60-Foot Tunnel with both the original leading-edge flap system and a new leading-edge flap system, which was designed with modem computational flow analysis and optimization tools. Leading-and trailing-edge flap deflections were generated for the original and modified leading-edge flap systems with the computational flow analysis and optimization tools. Although wind tunnel data indicated improvements in aerodynamic performance for the analytically derived flap deflections for both leading-edge flap systems, perturbations of the analytically derived leading-edge flap deflections yielded significant additional improvements in aerodynamic performance. In addition to the aerodynamic performance optimization testing, stability and control data were also obtained. An evaluation of the crosswind landing capability of the aircraft configuration revealed that insufficient lateral control existed as a result of high levels of lateral stability. Deflection of the leading-and trailing-edge flaps improved the crosswind landing capability of the vehicle considerably; however, additional improvements are required.

Hahne, David E.↗

DOE OSTI2024

Novel plasma actuator for mitigation of dynamic stall

A novel plasma actuator, the Linear Counter-flow using a Point Embedded Electrode (LCPEE), is developed for the prevention of dynamic stall for a sinusoidal pitching movement between α = 4° and α = 18°. The LCPEE is implemented on a NACA0012 airfoil and tested at a Reynolds Number of Re c = 2 × 105 and reduced frequency of k = π/16. Prior investigations using a standard linear actuator showed that the exposed electrode introduced perturbations passively which delayed dynamic stall when the actuator was off. For the LCPEE actuator, when turned off, there is least passive delay. When the LCPEE is turned on at St f = 50, the dynamic stall is prevented for the sinusoidal pitching motion of the airfoil. The LCPEE actuator is also tested for the same sinusoidal motion between α = 6° and α = 20°. Four cases are considered for the higher α range of motion: actuator off, actuator on at St f = 50 with a sinusoidal input waveform, actuator on at St f = 50 with a triangular input waveform, and actuator on at Stf = 100 with a sinusoidal input waveform. Specifically for the last case, experiment shows no flow reversal demonstrating the efficacy of LCPEE in controlling the dynamic stall. The effects of LCPEE on the flow energy distribution have also been studied by using proper orthogonal decomposition (POD) method.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Versatile system for ion energy measurements generated by pulsed laser ionization: Insights into electron-ion dynamics

Ion energy distributions generated by pulsed laser interactions with materials are essential for applications ranging from materials science to oncology. Ion energy characterization is particularly important for an emerging mass spectrometry technique called virtual-slit cycloidal mass spectrometry (VS-CMS). The ion energy distribution influences the design and performance of VS-CMS instruments, as well as the efficacy of laser-driven ionization methods in various fields. Several established techniques, including the retarding potential method, time-of-flight (TOF) analysis, and electrostatic energy analyzers, have been employed to measure ion energy distributions. The wide range of ion energies reported highlights the strong dependence of ion energy on laser parameters, target materials, and experimental conditions, as well as the necessity of making independent measurements of the ion energy distribution for specific laser systems and materials. This paper presents the design and characterization of a simple TOF-based apparatus for measuring ion energy distributions from pulsed laser ionization without external fields. This approach minimizes perturbation of electron-ion dynamics and enables simultaneous energy measurements at multiple spatial positions. Here, the apparatus was tested using a nanosecond pulsed Nd:YAG laser operating at 1064 nm, 532 nm, and 266 nm on solid copper sheets at various laser fluences. Simultaneous measurements at different distances provide new insights into ion-electron interactions post-ionization and demonstrate the influence of laser wavelength and fluence on ion energy distributions.

Ion energy↗

DOE OSTI2023

QFT in curved spacetime from quantum gravity: Proper WKB decomposition of the gravitational component

Starting from a reanalysis of previous work, we construct the proper low-energy quantum field theory (QFT) limit of a full quantum gravity theory in the Born-Oppenheimer approach. We separate the gravitational sector into a classical background, given by a vacuum diagonal Bianchi I cosmology, and its quantum perturbations represented by the two graviton degrees of freedom; we further include quantum matter in the form of a test scalar field. We then implement a Born-Oppenheimer separation, where the gravitons and matter play the roles of “slow” and “fast” quantum components, respectively, and perform a WKB expansion in a Planckian parameter. The functional Schrödinger evolution for matter is recovered after averaging over quantum-gravitational effects, provided that a condition is imposed on the gravitons’ wave functional. Such a condition fixes the graviton dynamics and is equivalent to the purely gravitational Wheeler-DeWitt constraint imposed in previous approaches. Here, the main accomplishment of the present work is to clarify that QFT in curved spacetime can be recovered in the low-energy limit of quantum gravity only after averaging over the graviton degrees of freedom, in the spirit of effective field theory. Furthermore, it justifies a posteriori the implementation of the gravitational Wheeler-DeWitt equation on the “slow” gravitons’ wave functional rather than assuming its validity a priori.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2022

Evaluating the Durability of Balance of Systems Components Using Combined-Accelerated Stress Testing

The degradation of photovoltaic (PV) balance of systems (BoS) components is not well-studied, but the consequences include offline modules, strings, and inverters; system shutdown; arc faults; and fires. A utility provider experienced a ~30% failure rate in their power transfer chain, originally attributed to branch connectors. Field-failed specimen assemblies were therefore examined, consisting of cable connector, branch connector, and discrete fuse components. In this study, unused field-vintage specimens are examined using combined-accelerated stress testing (C-AST) to clarify the most influential environmental stressors as well as the effect of external mechanical perturbation. A benchtop prototype fixture was used to develop the perturbation capability for the C-AST chamber. The benchtop experiments were also used to develop the in-situ data acquisition of specimen current, voltage, and temperature. A significant increase in operating temperature (~100 degrees C from ~40 degrees C) and a different failure mode were observed promptly once periodic mechanical perturbation was applied. The current at failure was decreased from 35 A (with failure in the fuses) to 15 A (failure at the male/female metal pin connection). After initial examination using X-ray computed tomography, the external plastic was machined away from failed specimens to allow for failure analysis, including the extraction of the internal convolute springs for morphological examination (optical and electron microscopy).

balance of systems↗