Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Modeling Contact Angle vs. Temperature for the Quartz-Water-Decane System

Innovative approaches are needed to improve the efficiency of oil recovery technologies to meet the growing demands of fossil-fuel based energy consumption. Enhanced oil recovery (EOR) methods such as low-salinity waterflooding and chemically tuned waterflooding aim to optimize the reservoir’s wetting properties, detaching oil globules from rock surfaces and allowing easier oil flow through pore throats. This wetting behavior is commonly quantified by contact angle measurements of the rock-oil-brine interface, which have been thoroughly investigated and theorized for many systems at ambient temperatures and pressures. However, few studies exist for extending contact angle theories away from ambient conditions. In this paper, we model the contact angles of a quartz-water-decane system at elevated temperatures using the surface tension component (STC) approach. Temperature-dependent van der Waals [Lifshitz-van der Waals (LW)] interactions and hydrogen-bonding (acid-base) interactions were calculated and are incorporated into the model for the quartz-water-decane interface. Additionally, the Hough and White procedure was used to create temperature-dependent dielectric functions of quartz, water, and normal decane for calculations of Hamaker coefficients. Hamaker coefficients calculated this way are highly linear with temperature and agree well with Israelachvili’s approximation. The acid-base interactions likely contribute the most to system wettability changes. Resulting contact angles of the quartz-water-decane system shift from water-wet (16°) to slightly water-wet (57.4°) as temperature increases. The model was also successfully verified for the quartz-air-water system. Our results can be used in future studies to determine optimal injected water compositions for specific rock-oil-brine and other systems with consideration of reservoir temperature.

02 PETROLEUM↗
DOE OSTI2024

3D Printing of Aqueous Two-Phase Systems with Linear and Bottlebrush Polyelectrolytes

In this study, we formed core–shell-like polyelectrolyte complexes (PECs) from an anionic bottlebrush polymer with poly (acrylic acid) side chains with a cationic linear poly (allylamine hydrochloride). By varying the pH, the number of side chains of the polyanionic BB polymers (Nbb), the charge density of the polyelectrolytes, and the salt concentration, the phase separation behavior and salt resistance of the complexes could be tuned by the conformation of the BBs. By combining the linear/bottlebrush polyelectrolyte complexation with all-liquid 3D printing, flow-through tubular constructs were produced that showed selective transport across the PEC membrane comprising the walls of the tubules. These tubular constructs afford a new platform for flow-through delivery systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Investigation of porous polydimethylsiloxane structures with tunable properties induced by the phase separation technique

This article reports the fabrication and characterization of porous polydimethylsiloxane (PDMS) structures developed by the solvent evaporationinduced phase separation technique. Here, ternary systems containing water/ tetrahydrofuran (THF)/PDMS with various concentrations are produced to form a stable solution. The porous PDMS structures are formed by removing the solvent (THF) and nonsolvent (water) phases during the stepping heat treatment procedure. The analytical ternary phase diagram is constructed based on the thermodynamic equilibrium state in the polymer solution to explain the stable/unstable formulations and the possible composition change path. The results show that the isolated pores with the adjustable pore size ranging from 330 to 1900 μm are obtained by tuning the water to the THF ratio. The mechanical properties of the porous PDMS structures are determined by conducting the tensile tests on the prepared dog bone-shaped specimens. A wide range of elastic modulus ranging between 0.49 and 1.05 MPa was achieved without affecting the density of the porous sample by adjusting the solvent and non-solvent content in the solution. It is shown that the flexibility of the porous structures can be improved by reducing the ratio of water to THF and decreasing the PDMS content. The porosity measurements reveal that the PDMS concentration is the major phase controlling the porosity of the structure, while the effect of water/THF is negligible.

42 ENGINEERING↗
DOE OSTI2022

Unveiling real‐time crystallization with nucleators and thickeners for zinc nitrate hexahydrate as a phase change material

Abstract The primary challenge of salt hydrates as phase change materials (PCMs) is their high degree of supercooling (∆ T Sup ). Past studies have attempted to alleviate ∆ T Sup by incorporating nucleators possessing similar lattice structure, without a thorough analysis of the nucleator/PCM interactions. This work presents a novel in‐operando study to visually observe the crystallization process of zinc nitrate hexahydrate (ZNH) in real‐time using suitable nucleators and a thickener. We have introduced a new dataset where zinc acetate dihydrate (ZnAc.2H) has been employed as an additive to ZNH for thermal energy storage (TES). According to our in‐operando study, ZnAc.2H underwent hydrolysis in molten ZNH to precipitate needle‐like ZnO particles, which acted as nucleators for the PCM. In the absence of a thickener, the crystal propagation of ZNH exhibited a preferential directional tendency, whereas incorporation of thickener made the phase change process uniform along all directions. Self‐hydrolysis of ZnAc.2H generated excess water which caused the undesirable effect of broadening the endothermic peak. The addition of carboxymethyl cellulose (CMC) thickener could restrict the activity of excess water and reduce the broadening of the endothermic peak. Differential scanning calorimetry (DSC) revealed that 5 wt% ZnAc.2H additive and 2 wt% CMC thickener added to ZNH can considerably improve the TES properties of ZNH PCM (∆ H Fusion 125.9 J·g −1 , ∆ T Sup 3.0°C, melting point [M.P.] 29.0°C). Our in‐operando studies can unveil real‐time phase change behaviors to better design PCM systems with desired characteristics.

Chakraborty, Anirban↗
DOE OSTI2022

Revealing the dynamics of the alloying and segregation of Pt-Co nanoparticles via in-situ environmental transmission electron microscopy

Thermal treatment is a general and efficient way to synthesize intermetallic catalysts and may involve complicated physical processes. So far, the mechanisms leading to the size and composition heterogeneity, as well as the phase segregation behavior in Pt-Co nanoparticles (NPs) are still not well understood. Here, via in-situ environmental transmission electron microscopy, the formation dynamics and segregation behaviors of Pt-Co alloyed NPs during the thermal treatment were investigated. It is found that Pt-Co NPs on zeolitic imidazolate frameworks-67-derived nanocarbon (NC) are formed consecutively through both particle migration coalescence and the Ostwald ripening process. The existence of Pt NPs is found to affect the movement of Co NPs during their migration. With the help of theoretical calculations, the correlations between the composition and migration of the Pt and Co during the ripening process were uncovered. Herein, these complex alloying processes are revealed as key factors leading to the heterogeneity of the synthesized Pt-Co alloyed NPs. Under oxidation environment, the Pt-Co NPs become surface faceted gradually, which can be attributed to the oxygen facilitated relatively higher segregation rate of Co from the (111) surface. This work advances the fundamental understanding of design, synthesis, and durability of the Pt-based nanocatalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermodynamic Modeling of Aqueous LiCl, LiBr, LiI, and LiNO 3 Solutions

Thermodynamic models are essential to facilitate the advancement of process design, optimization, and operation of electrolyte systems. In this work, a comprehensive thermodynamic framework based on the Electrolyte Nonrandom Two-Liquid model is developed to calculate phase equilibria behavior and salt solubility of aqueous LiCl, LiBr, LiI, and LiNO 3 solutions. The model describes the non-ideality of the electrolyte solutions by using two binary interaction parameters for each electrolyte-molecule pair in the system. Each binary interaction parameter is further expressed with up to three temperature coefficients which are regressed from experimental data. To take into account the hydration of lithium ion, two separate chemistries for the dissociation of lithium salts are investigated. In the first case, the lithium ion is considered as a bare ion, Li + , while in the second case hydration of the lithium ion from Li + to Li(H 2 O) + is considered. Here, the calculated thermodynamic properties compare adequately with the experimental data for both sets of chemistries for concentrations up to saturation and temperatures from 273.15 K up to 623.15 K. Moderate to significant improvements are observed with the incorporation of the hydration chemistry for aqueous LiCl, LiBr, and LiI solutions when compared to the non-hydrated lithium ion model results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Extended continuous cooling transformation diagram for 410 stainless steel encompassing δ → γ and γ → αʹ transformations determined by dilatometry

In this study, we use dilatometry to construct an extended Continuous Cooling Transformation (CCT) diagram for 410 stainless steel, capturing both δ → γ and γ → αʹ transformations specifically for directed energy deposition (DED) additive manufacturing (AM) applications. To ensure that the findings are representative of AM specific microstructures and compositions, dilatometry coupons were extracted from a wire arc DED wall, thereby preserving the inherent microstructural and compositional variability within the material. The on-heating phase transformations, including A c1 , A c3 , and γ → δ, were found to be essentially location independent, despite the typical heterogeneity associated with AM. Conversely, increasing cooling rates were observed to shift the start and finish temperatures of both δ → γ and γ → αʹ transformations to lower values. The resulting extended CCT diagram offers a more complete depiction of phase transformation behavior in the system, enabling accurate microstructure evolution modeling and residual stress predictions specifically for directed energy deposition additive manufacturing applications.

Additive manufacturing↗
DOE OSTI2023

An examination of the precipitation behavior of proton irradiated dual phase 308L weldment filler materials

Voids, G phase particles, and Ni-Si rich clusters in proton irradiated dual phase 308L groove filler of a SA508–304 L dissimilar metal weldment are analyzed using advanced characterization techniques. These weldments are often used in light water nuclear reactors and are subject to enhanced corrosion and associated stress corrosion cracking (SCC). Radiation damage is known to accelerate SCC. Ni-Si enriched clusters were observed in proton irradiated γ austenite, while G phase M 6 Ni 16 Si 7 (where M transition metal element) precipitates were observed in proton irradiated δ ferrite. Compositional analysis of the G phase precipitates and Ni-Si clusters from STEM-EDS and APT are compared. Unlike G phase particles in proton irradiated δ ferrite, Ni-Si clusters in proton irradiated γ austenite are not rich in Mn. Both STEM-EDS and APT line-scan profiles of the Ni-Si clusters show that the Fe and Cr concentration gradient between matrix γ austenite and the Ni-Si clusters is not as sharp as those between matrix δ ferrite and G phase. Further, HR-STEM imaging indicates that the lattice parameter of the Ni-Si clusters is commensurate with γ austenite and the clusters do not represent the precipitation of a second phase. Finally, our analysis demonstrates the density and volume fraction of G phase particles and the density of voids scales with proton irradiation damage and the energy to recoils.

308L groove filler↗
DOE OSTI2021

Modeling cell venting and gas-phase reactions in 18650 lithium ion batteries during thermal runaway

A numerical model is developed to study cell venting, internal pressure, and gas-phase dynamics behavior of 18650 Li-ion cells undergoing thermal runaway. A k-e Reynolds-Averaged Navier-Stokes (RANS) model is adopted to describe the turbulent flow out of the cells, while the fluid dynamics inside the cells is described by Darcy-Forchheimer's equation. Thermal abuse reactions and gas generation kinetics are described by a single-step lumped reaction model. Then, a series of computational fluid dynamics (CFD) simulations are conducted on a single 18650 cell at various states-of-charge (100%, 50%, 25%) to study detailed flow and thermal behavior as a function of quantity of gas generated during cell venting. Venting events are categorized into two stages: i) breaching of the cell container and ii) thermal runaway reactions. It is found that the cell response is dominated by the second stage since most of the gases are generated during thermal runaway. Also, the propensity for propagation is highly affected by state-of-charge (SOC). Cells at higher SOCs produce more heat and gas during the venting event, owing to higher mass and concentrations of reacting gases, and consequently reach higher internal cell pressures which increase the risk of side-wall breaching.

25 ENERGY STORAGE↗
DOE OSTI2021

Effect of microphase separation on the limiting current density in hybrid organic-inorganic copolymer electrolytes

Hybrid organic-inorganic block copolymer electrolytes are of interest to enable batteries containing lithium metal anodes. The conductive block is a standard polymer electrolyte of poly(ethylene oxide) and the mechanically rigid block is an inorganic poly(acryloisobutyl polyhedral oligomeric silsesquioxane) polymer. Here, in this paper, we compare a poly(acryloisobutyl polyhedral oligomeric silsesquioxane)-b-poly(ethylene oxide)-b-poly(acryloisobutyl polyhedral oligomeric silsesquioxane) (POSS-PEO-POSS) triblock copolymer and a poly(ethylene oxide)-b- poly(acryloisobutyl polyhedral oligomeric silsesquioxane) (PEO-POSS) diblock copolymer mixed with lithium bis(trifluoromethanesulfonyl)imide salt. We have experimentally measured the limiting current density in lithium symmetric cells containing hybrid organic-inorganic electrolytes at 90 °C. The cells were polarized at a large range of applied current density. The diblock copolymer electrolyte exhibited a clear plateau in cell potential at all current densities below the limiting current density. At low applied current density, the triblock copolymer electrolyte also exhibited a clear plateau in cell potential. At currents approaching the limiting current density, the triblock copolymer electrolyte exhibited an underdamped potential profile. The cell potential did not reach a plateau at current densities above the limiting current in both systems. The diblock and triblock copolymer electrolytes were fully characterized using electrochemical methods to determine the ionic conductivity, cation current fraction, salt diffusion coefficient, and open circuit voltage as a function of salt concentration. Cell potential and salt concentration as functions of position in the cell at various current densities were calculated using Newman's concentrated solution theory. The theoretical limiting current density was calculated to be the current density at which salt is depleted at the cathode. We see quantitative agreement between experimental measurements and theoretical predictions for the limiting current density in the diblock copolymer electrolyte which has an ordered structure at all salt concentrations, while the experimental limiting current density is lower than the theoretical prediction for the triblock copolymer electrolyte, which exhibits a disordered morphology at high salt concentrations.

25 ENERGY STORAGE↗
DOE OSTI2020

Understanding Superionic Conductivity in Lithium and Sodium Salts of Weakly Coordinating Closo -Hexahalocarbaborate Anions

Solid-state ion conductors based on closo-polyborate anions combine high ionic conductivity with a rich array of tunable properties. Cation mobility in these systems is intimately related to the strength of the interaction with the neighboring anionic network and the energy for reorganizing the coordination polyhedra. In this paper, we explore such factors in solid electrolytes with two anions of the weakest coordinating ability, [HCB 11 H 5 Cl 6 ] – and [HCB 11 H 5 Br 6 ] – , and a total of 11 polymorphs are identified for their lithium and sodium salts. Our approach combines ab initio molecular dynamics, synchrotron X-ray powder diffraction, differential scanning calorimetry, and AC impedance measurements to investigate their structures, phase-transition behavior, anion orientational mobilities, and ionic conductivities. We find that M(HCB 11 H 5 X 6 ) (M = Li, Na, X = Cl, Br) compounds exhibit order–disorder polymorphic transitions between 203 and 305 °C and display Li and Na superionic conductivity in the disordered state. Through detailed analysis, we illustrate how cation disordering in these compounds originates from a competitive interplay among the lattice symmetry, the anion reorientational mobility, the geometric and electronic asymmetry of the anion, and the polarizability of the halogen atoms. These factors are compared to other closo-polyborate-based ion conductors to suggest guidelines for optimizing the cation–anion interaction for fast ion mobility. This study expands the known solid-state poly(carba)borate-based materials capable of liquid-like ionic conductivities, unravels the mechanisms responsible for fast ion transport, and provides insights into the development of practical superionic solid electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Intermediate Species in the Crystallization of Sodium Aluminate Hydroxy Hydrates

In highly alkaline “water-in-salt” Na 2 O/Al 2 O 3 /H 2 O solutions where the monomeric Al(OH) 4 - anion dominates, isolation of transitional species that seed crystallization of sodium aluminate salt hydrates has been challenging. For example, discrimination of dimeric [e.g., Al 2 O(OH) 6 2- ] from species via 27 Al nuclear magnetic resonance (NMR) spectroscopy is limited via fast interconversion through hydrolysis and condensation reactions. Despite this, using magic-angle spinning NMR ( 27 Al MAS NMR) at high magnetic field strengths (14.1 and 20.0 T) on crystals of nonasodium bis(hexahydroxyaluminate) trihydroxide hexahydrate [NSA, Na 9 [Al(OH) 6 ] 2 ·3(OH)·6(H 2 O)], we observed a 27 Al resonance consistent with Na 2 Al 2 O(OH) 6 . This tetrahedral dimeric species was also identified in the mother liquor by Raman spectroscopy while remaining expectedly unresolved by high-field liquid-state 27 Al NMR. Its substantial abundance in the mother liquor and as either an interstitial or an adsorbate on precipitated solids suggest that it plays a crucial role in NSA crystallization. Here, our detailed characterization, which includes single-pulse 27 Al MAS NMR, nutation 27 Al MAS NMR, and multiple quantum 27 Al MAS NMR, provides new molecular insights into how aluminate transitions from tetrahedral in solution to octahedral in solid. This understanding could ultimately lead to better predictions of aluminum phase change behavior in caustic sodium hydroxide with wide-ranging technological and environmental implications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Reaction Heterogeneity in LiFePO 4 Agglomerates and the Role of Intercalation-Induced Stress

As an important battery cathode material, reaction distribution in lithium iron phosphate (LiFePO4) has been extensively studied in dispersed particle systems, but remains poorly understood for mesoscopic agglomerates (or secondary particles) that are used in most commercial batteries. Herein, we apply three-dimensional X-ray spectroscopic imaging to characterize the two-phase structure in LiFePO4 secondary particles during electrochemical cycling. (De)lithiated domains are found to not form the commonly assumed core-shell structure but develop highly anisotropic filamentary morphology that is rate independent and symmetric between charging and discharging. Phase-field simulations elucidate that the observed 1D phase growth behavior is not caused by the 1D lithium diffusivity of LiFePO4 but the elastic interaction between primary particles, which gives rise to stronger reaction heterogeneity than dispersed nanoparticles. As a result, uniform lithium (de)intercalation does not occur on the secondary particle surface even at high cycling rates.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Revealing Fast Cu-Ion Transport and Enhanced Conductivity at the CuInP 2 S 6 –In 4/3 P 2 S 6 Heterointerface

Van der Waals layered ferroelectrics, such as CuInP 2 S 6 (CIPS), offer a versatile platform for miniaturization of ferroelectric device technologies. Control of the targeted composition and kinetics of CIPS synthesis enables the formation of stable self-assembled heterostructures of ferroelectric CIPS and nonferroelectric In 4/3 P 2 S 6 (IPS). Here, we use quantitative scanning probe microscopy methods combined with density functional theory (DFT) to explore in detail the nanoscale variability in dynamic functional properties of the CIPS-IPS heterostructure. Within, we report evidence of fast ionic transport which mediates an appreciable out-of-plane electromechanical response of the CIPS surface in the paraelectric phase. Further, we map the nanoscale dielectric and ionic conductivity properties as we thermally stimulate the ferroelectric-paraelectric phase transition, recovering the local dielectric behavior during this phase transition. Finally, aided by DFT, we reveal a substantial and tunable conductivity enhancement at the CIPS/IPS interface, indicating the possibility of engineering its interfacial properties for next generation device applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Amphiphilic Co-Solvents Modulate the Structure of Membrane Domains

Biofuels are an increasing part of the sustainable energy picture. This makes it a societal and economic imperative to optimize biofuel production. Mitigating the toxic effects of amphiphilic co-solvents is one way to improve the efficiency of biofuel production. Amphiphiles partition into cellular membranes, leading to membrane thinning, destabilization, loss of membrane potential, and, ultimately, cell death. However, this picture of solvent toxicity misses the disruptive impact of co-solvents on lateral membrane organization, which is increasingly recognized as critical for membrane protein sorting and oligomerization. The alteration or disruption of membrane domains has deleterious effects on cellular processes. Here, in this work, we pursue the hypothesis that membrane lateral organization is disrupted by the presence of co-solvents at concentrations lower than those which lead to full membrane destabilization. The disruption occurs due to an increasing interfacial tension between the co-existing phases, resulting in conformational changes to minimize the interfacial length-to-area ratio. This represents an unrecognized mode of solvent-induced stress and a new target for interventions to improve fermentation yields.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Multivariate Flexible Framework with High Usable Hydrogen Capacity in a Reduced Pressure Swing Process

Step-shaped adsorption-desorption of gaseous payloads by flexible metal-organic frameworks can facilitate the delivery of large usable capacities with significantly reduced energetic penalties. This is desirable for the storage, transport, and delivery of H 2 , as prototypical adsorbents require large swings in pressure and temperature to achieve usable capacities approaching their total capacities. However, the weak physisorption of H 2 typically necessitates undesirably high pressures to induce the framework phase change. As de novo design of flexible frameworks is exceedingly challenging, the ability to intuitively adapt known frameworks is required. We demonstrate that the multivariate linker approach is a powerful tool for tuning the phase change behavior of flexible frameworks. In this work, 2-methyl-5,6-difluorobenzimidazolate was solvothermally incorporated into the known framework CdIF-13 (sod-Cd(benzimidazolate) 2 ), resulting in the multivariate framework sod-Cd(benzimidazolate) 1.87 (2-methyl-5,6-difluorobenzimidazolate) 0.13 (ratio = 14:1), which exhibited a considerably reduced stepped adsorption threshold pressure while maintaining the desirable adsorption-desorption profile and capacity of CdIF-13. At 77 K, the multivariate framework exhibits stepped H 2 adsorption with saturation below 50 bar and minimal desorption hysteresis at 5 bar. At 87 K, saturation of step-shaped adsorption occurs by 90 bar, with hysteresis closing at 30 bar. These adsorption-desorption profiles enable usable capacities in a mild pressure swing process above 1 mass %, representing 85-92% of the total capacities. Here this work demonstrates that the desirable performance of flexible frameworks can be readily adapted through the multivariate approach to enable efficient storage and delivery of weakly physisorbing species.

08 HYDROGEN↗
DOE OSTI2024

Cascade CO 2 Insertion in Carbanion Ionic Liquids Driven by Structure Rearrangement

The CO 2 chemisorption in state-of-the-art sorbents based on oxide/hydroxide/amine moieties is driven by strong chemical bonding formation in the carbonate/bicarbonate/carbamate products, which in turn leads to high energy input in sorbent regeneration. In addition, the CO 2 uptake capacity was limited by the active sites’ utilization efficiency, with each active site incorporating one CO 2 molecule or less. In this work, a new concept and generation of sorbent was developed to achieve cascade insertion of multiple CO 2 molecules by leveraging structure rearrangement as the driving force, leading to in situ generation of extra CO 2 -binding sites and significantly reduced energy input for CO 2 release. The designed ionic liquids (ILs) containing carbanions with conjugated and asymmetric structure, deprotonated (methylsulfonyl)acetonitrile ([MSA]) anion, allowed the cascade insertion of two CO 2 molecules via consecutive C–C and O–C bond formations. The proton transfer and structure rearrangement of the carboxylic acid intermediates played critical roles in stabilizing the first integrated CO 2 and generating extra electron-rich oxygen sites for the insertion of the second CO 2 . The structure variation and reaction pathway were confirmed by operando spectroscopy, magnetic resonance spectroscopy (NMR), mass spectroscopy, and computational chemistry. The energy input in sorbent regeneration could be further reduced by harnessing the phase-changing behavior of the carbanion salts in ether solutions upon reacting with CO 2 , avoiding the energy consumption in heating the solvent. In conclusion, the fundamental insights obtained herein provide a promising approach to greatly improve the CO 2 sorption performance via sophisticated molecular-scale structural engineering of the sorbents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗