Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase delays”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Phase separation and state oscillation of active inertial particles

Active matter systems are of great interest for their novel out-of-equilibrium collective behavior. Active Brownian particles (ABPs) are known to exhibit clustering and motility-induced phase separation, and there have been many studies revealing this rich behavior in the overdamped limit of Brownian motion, where inertial effects are insignificant. In this work, we simulate an Active Inertial Particle (AIP) model where we focus on the underdamped, rather than overdamped limit, to study the interplay between particle inertia and collective behavior, such as phase separation. We show that inertia reduces particle motility due to collisions and a longer time delay for particles to regain speed, thereby suppressing phase separation relative to that observed in the overdamped limit. Additionally, we observe interesting oscillatory behavior between a phase separated steady-state and a homogeneous fluid state that results from inertia-induced collective motion within active clusters due to momentum transfer. Such oscillatory behavior has been reported for ABP systems with particle shape anisotropy, where collective motion is mediated by particle shape anisotropy. Furthermore, we confirm that there is no single characteristic frequency for the oscillatory behavior. The power spectral density is a power law in the high frequency domain, with an exponent close to -2.5.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Radar Observations of Asteroid 10115 (1992 SK)

The approach of 1992 SK to within 0.056 AU of Earth on 1999 March 26 provided an excellent opportunity for radar observations. We observed it daily between March 22-26 at Goldstone at a transmitter frequency of 8560 MHz (3.50 cm). Weighted, optimally smoothed sums of cw (Doppler-only) echoes achieve a signal-to-noise ratio of about 300. Our highest resolution cw setup places up to approx. 30 0.5-Hz Doppler cells on the target at echo powers exceeding two standard deviations of the noise. Our highest resolution imaging setup places about 20 0.25-us (37.5 m) x 2.0 Hz pixels on 1992 SK at echo powers above the same threshold. We completed nearly 300 runs with each setup and obtained thorough rotational phase coverage (period = 7.320 h, P. Pravec, pers. comm.). The dispersion of the echoes in time delay indicates a lower bound on 1992 SK's maximum pole-on breadth of approx. 0.4 km that is consistent with the echo bandwidth and rotation period. Variations in the cw spectral bandwidths and shapes and in the delay-Doppler images as a function of rotation phase are evident on each day, are consistent in bandwidth with each other and with the rotation period, and indicate that the asteroid is asymmetric and modesty elongated.

Benner, L. A. M.↗

Estimating Accurate Relative Spacecraft Angular Position from DSN VLBI Phases Using X-Band Telemetry or DOR Tones

At present spacecraft angular position with Deep Space Network (DSN) is determined using group delay estimates from very long baseline interferometer (VLBI) phase measurements employing differential one way ranging (DOR) tones. As an alternative to this approach, we propose estimating position of a spacecraft to half a fringe cycle accuracy using time variations between measured and calculated phases as the Earth rotates using DSN VLBI baseline(s). Combining fringe location of the target with the phase allows high accuracy for spacecraft angular position estimate. This can be achieved using telemetry signals of at least 4-8 MSamples/sec data rate or DOR tones.

x-band telemetry↗

Obtaining Reliable Predictions of Terrestrial Energy Coupling From Real-Time Solar Wind Measurement

The first draft of a manuscript titled "Variable time delays in the propagation of the interplanetary magnetic field" has been completed, for submission to the Journal of Geophysical Research. In the preparation of this manuscript all data and analysis programs had been updated to the highest temporal resolution possible, at 16 seconds or better. The program which computes the "measured" IMF propagation time delays from these data has also undergone another improvement. In another significant development, a technique has been developed in order to predict IMF phase plane orientations, and the resulting time delays, using only measurements from a single satellite at L1. The "minimum variance" method is used for this computation. Further work will be done on optimizing the choice of several parameters for the minimum variance calculation.

Weimer, Daniel R.↗

Predicting zeolites’ stability during the corrosion of nuclear waste immobilization glasses: Comparison with glass corrosion experiments

During the long-term corrosion of nuclear waste glasses under nuclear waste disposal conditions, the precipitation of zeolitic phases has been linked to a delayed acceleration in glass corrosion (known as “Stage III”). Hence, predicting the thermodynamic propensity for zeolites to form upon the dissolution of nuclear waste glasses is key to ensure their long-term performance. Here, we compile a unified, internally-consistent thermodynamic database “clay20” to estimate the stability of clay and feldspar phases relevant to nuclear waste immobilization glasses, including beidellite(Mg, Ca, Na, K), kaolinite, montmorillonite(Mg, Ca, Na, K), nontronite(Mg, Ca, Na, K), saponite(Ca, Na, K), and albite. Based on this, we report a geochemical modeling method allowing us to predict the stability of secondary phases (including zeolites, calcium–silicate–hydrate gels, and clays) upon the dissolution of nuclear waste immobilization glasses. We show that this approach offers a realistic description of the stability of the secondary phases forming during the dissolution of two archetypical model nuclear glasses (namely, the International Simple Glass, ISG, and WVUTh-203) under conditions relevant to nuclear waste disposal (T = 90°C, p = 1 bar) as a function of pH. We find that the formation of silica and clay secondary phases is thermodynamically favored at low pH (pH < 10), whereas, in contrast, zeolite (analcime) and calcium–silicate–hydrate phases are favored at high pH (pH > 10.5). This suggests that thermodynamics (i.e., not solely kinetics) plays a key role in determining the range of solution pH wherein stage III corrosion may occur, i.e., when zeolite formation is favored.

Zhen-Wu, Bi Yun↗

Time and frequency transfer by the Master-Slave Returnable Timing System technique - Application to solar power transmission

The concept of the Master Slave Returnable Timing System (MSRTS) is presented which combines the advantages of the master slave (MS) and the Returnable Timing System (RTS) for time and frequency transfer. The basic idea of MSRTS is to send the time-frequency signal received at a particular node back to the sending node. The delay accumulated by this return signal is used to advance the phase of the master (sending) node thereby canceling the effect of the delay introduced by the path. The method can be used in highly accurate clock distribution systems required in avionics, computer communications, and large retrodirective phased arrays such as the Solar Power Satellite.

Lindsey, W. C.↗

The Influence of Cloud Types on Cloud–Radiative Forcing During DYNAMO/AMIE

Cloud-radiative feedback is known to be an important process for the Madden-Julian Oscillation (MJO) and its accurate representation in general circulation models. The MJO is known to have a stronger cloud-radiative feedback compared to higher frequency convectively coupled equatorial waves (CCEW), for reasons that remain unclear. The objective of this study is to use data from the Dynamics of the MJO/Atmospheric Radiation Measurement MJO Investigation Experiment field campaign to investigate how cloud type evolution and their associated cloud-radiative forcing (CRF) differ between the MJO and CCEWs and their application to MJO dynamics under moisture mode theory. This study finds that the amplitude of CRF is the largest within the MJO compared to the higher frequency CCEWs, and CRF maximizes after the maximum precipitation (enhanced phase) of the MJO. We suggest this delay in the timing of maximum CRF occurs because most cloud types (congestus, deep, anvil, and cirrus) simultaneously maximize in frequency after the enhanced phase of the MJO, which is not seen for the higher frequency CCEWs. These specific cloud types help maintain the MJO through their radiatively-driven moistening which acts to prolong the enhanced phase of the MJO. The decomposition of radiatively-driven moistening by cloud types shows that simultaneous moistening by deep, anvil, and congestus clouds are particularly responsible for the maintenance of the MJO under moisture mode theory. Further, this analysis suggests the importance of capturing the correct evolution of different cloud types and their associated radiative effects to better understand the thermodynamics of the MJO.

54 ENVIRONMENTAL SCIENCES↗

On The Processing of Log Files for Monitoring Antenna Health

In order to improve the quality of geodetic results, we have developed an infrastructure for timely processing of telemetry from IVS observing stations. We check every hour for new log files with telemetry from both VLBI observing sessions, single dish experiments, and stow-in data collection and automatically process them. The telemetry data we use is the system temperature, phase calibration phases and amplitudes, system equivalent flux density, and the differences between formatter clock and GPS clock. For the system temperature and phase calibration, processing includes filtering out outliers and computing averages and rms of the scatter in each scan. Furthermore, for the phase calibration we also compute the group delay and detect spurious signals. Cleaned and post-processed telemetry is archived. Our process detects abnormalities, such as, anomalously high system temperature, unstable phase calibration phases, jumps in the GPS and formatter clock differences, and others. With our procedure, the latency of detection of station abnormalities is reduced to less than two hours. Early detection of abnormalities reduces the amount of affected data since station personnel get early alerts. We discuss our experience of running this system since 2022.

Phase Calibration↗

On The Processing of Log Files for Monitoring Antenna Health

In order to improve the quality of geodetic results, we have developed an infrastructure for timely processing of telemetry from IVS observing stations. We check every hour for new log files with telemetry from both VLBI observing sessions, single dish experiments, and stow-in data collection and automatically process them. The telemetry data we use is the system temperature, phase calibration phases and amplitudes, system equivalent flux density, and the differences between formatter clock and GPS clock. For the system temperature and phase calibration, processing includes filtering out outliers and computing averages and rms of the scatter in each scan. Furthermore, for the phase calibration we also compute the group delay and detect spurious signals. Cleaned and post-processed telemetry is archived. Our process detects abnormalities, such as, anomalously high system temperature, unstable phase calibration phases, jumps in the GPS and formatter clock differences, and others. With our procedure, the latency of detection of station abnormalities is reduced to less than two hours. Early detection of abnormalities reduces the amount of affected data since station personnel get early alerts. We discuss our experience of running this system since 2022.

VLBI↗

Electrically-Tunable Group Delays Using Quantum Wells in a Distributed Bragg Reflector

There is a growing interest in the fabrication of semiconductor optical group delay lines for the development of phased arrays of Vertical-Cavity Surface-Emitting Lasers (VCSELs). We present a novel structure incorporating In(x)GA(1-x)As quantum wells in the GaAs quarter-wave layers of a GaAs/AlAs distributed Bragg reflector (DBR). Application of an electric field across the quantum wells leads to red shifting and peak broadening of the el-hhl exciton peak via the quantum-confined Stark effect. Resultant changes in the index of refraction thereby provide a means for altering the group delay of an incident laser pulse. We discuss the tradeoffs between the maximum amount of change in group delay versus absorption losses for such a device. We also compare a simple theoretical model to experimental results, and discuss both angle and position tuning of the BDR band edge resonance relative to the exciton absorption peak. The advantages of such monolithically grown devices for phased-array VCSEL applications will be detailed.

Nelson, Thomas R., Jr.↗

Advanced Intra-Cycle Detection of Pre-Ignition Events through Phase-Space Transforms of Cylinder Pressure Data

The widespread adoption of boosted, downsized SI engines has brought pre-ignition phenomena into greater focus, as the knock events resulting from pre-ignitions can cause significant hardware damage. Much attention has been given to understanding the causes of pre-ignition and identify lubricant or fuel properties and engine design and calibration considerations that impact its frequency. This helps to shift the pre-ignition limit to higher specific loads and allow further downsizing but does not fundamentally eliminate the problem. Real-time detection and mitigation of pre-ignition would thus be desirable to allow safe engine operation in pre-ignition-prone conditions. This study focuses on advancing the time of detection of pre-ignition in an engine cycle where it occurs. Furthermore, phase space transforms through time-delay embedding of cylinder pressure and principal component analysis were applied to same-cycle detection of pre-ignition and shown to enable detection on the order of a crank degree earlier than deviation in cylinder pressure can be identified through direct statistical observation of the pressure data. Additionally, it appears that the deviation of the trajectory in phase space may offer the opportunity to extend this method to further extend the detection window and allow more time for mitigation actions to occur.

42 ENGINEERING↗

A Ka-band GaAs monolithic phase shifter

The design and performance of a GaAs monolithic 180-degree one-bit switched line phase shifter test circuit for Ka-band operation is presented. A self-aligned gate (SAG) fabrication technique is also described that reduces resistive parasitics in the switching FET's. Over the 27.5-30 GHz band, typical measured differential insertion phase is within 10-20 deg of the ideal time delay characteristic. Over the same band, the insertion loss for the SAG phase shifter is about 2.5-3 dB per bit. The SAG fabrication technique holds promise in reducing phase shifter insertion loss to about 1.5 dB/bit for 30-GHz operation.

Sokolov, V.↗

Centering a DDR Strobe in the Middle of a Data Packet

The Orion CEV Northstar ASIC (application- specific integrated circuit) project required a DDR (double data rate) memory bus driver/receiver (DDR PHY block) to interface with external DDR memory. The DDR interface (JESD79C) is based on a source synchronous strobe (DQS\) that is sent along with each packet of data (DQ). New data is provided concurrently with each edge of strobe and is sent irregularly. In order to capture this data, the strobe needs to be delayed and used to latch the data into a register. A circuit solves the need for training a DDR PRY block by incorporating a PVT-compensated delay element in the strobe path. This circuit takes an external reference clock signal and uses the regular clock to calibrate a known delay through a data path. The compensated delay DQS signal is then used to capture the DQ data in a normal register. This register structure can be configured as a FIFO (first in first out), in order to transfer data from the DDR domain to the system clock domain. This design is different in that it does not rely upon the need for training the system response, nor does it use a PLL (phase locked loop) or a DLL (delay locked loop) to provide an offset of the strobe signal. The circuit is created using standard ASIC building blocks, plus the PVT (process, voltage, and temperature) compensated delay line. The design uses a globally available system clock as a reference, alleviating the need to operate synchronously with the remote memory. The reference clock conditions the PVT compensated delay line to provide a pre-determined amount of delay to any data signal that passes through this delay line. The delay line is programmed in degrees of offset, so that one could think of the clock period representing 360deg of delay. In an ideal environment, delaying the strobe 1/4 of a clock cycle (90deg) would place the strobe in the middle of the data packet. This delayed strobe can then be used to clock the data into a register, satisfying setup and hold requirements of the system.

Johnson, Michael↗

On the 2018 Outburst of the Accreting Millisecond X-Ray Pulsar Swift J1756.9-2508 As Seen with NICER

We report on the coherent timing analysis of the 182 Hz accreting millisecond X-ray pulsar SwiftJ1756.92508during its 2018 outburst as observed with the Neutron Star Interior Composition Explorer (NICER). Combiningour NICER observations with Rossi X-ray Timing Explorer observations of the 2007 and 2009 outbursts, we alsostudied the long-term spin and orbital evolution of this source. We find that the binary system is well describedby a constant orbital period model, with an upper limit on the orbital period derivative of Pb < 7.4 ´ 10-13 ss1.Additionally, we improve upon the source coordinates through astrometric analysis of the pulse arrival times,finding R.A.=17h56m57 18±0 08 and decl.=25°0627 8±3 5, while simultaneously measuring thelong-term spin frequency derivative as n = -7.3 ´ 10-16 Hzs1. We briefly discuss the implications of thesemeasurements in the context of the wider population of accreting millisecond pulsars. We reported on the coherent timing analysis of the 2018 outburst of Swift J1756 as observed with NICER. Consistent with analyses of the previous outbursts (Krimm et al. 2007b; Patruno et al. 2010), we find that the X-ray pulsations have energy dependent amplitudes; the fractional amplitude of the fundamental increases with energy, whereas the fractional amplitude of the harmonic shows a slight decline with energy. This energy dependent behavior is not unusual in AMXPs (Patruno & Watts 2012) and can be interpreted in terms of the thermal emission from the stellar hotspot and reprocessing in the accretion column (e.g., Gierliński et al. 2002; Ibragimov & Poutanen 2009). The pulse arrival times of the 2018 outburst are well described by a timing model consisting of a circular orbit with a constant spin frequency. The pulse phases with respect to this model do not show spurious residuals with time or orbital phase, and no evidence is found that the pulse arrival times exhibit an additional delay associated with passing through the gravitational well of the companion star (Shapiro delay). We note, however, that the expected Shapiro delay is given as (Shapiro et al. 1971) Equation (5) where Φ is the orbital phase, G is the gravitational constant, c is the speed of light, and i is the inclination. Even for the maximum allowed companion mass, ${M}_{C}=0.030\,{M}_{\odot }$ (Krimm et al. 2007b, but see Section 4.2 for more details) and an inclination of 90°, the largest delay we can expect is only 4 μs. As this time-delay is smaller than the uncertainty on our phase residuals by nearly two orders of magnitude (see Figure 1), we are not sensitive to Shapiro delays in Swift J1756. Comparing our measurements for the 2018 outburst with those of the 2007 and 2009 outbursts as observed with RXTE, we analyzed the long-term evolution of this source. We found that the binary system is consistent with having a constant orbital period and that the pulsar shows a spin frequency derivative of $\dot{\nu }=-7.3\times {10}^{-16}\,\mathrm{Hz}\,{{\rm{s}}}^{-1}$. 4.1. Spin-down Evolution The long-term spin frequency derivative measured in Swift J1756 is of the same order as the spin frequency derivatives measured in other AMXPs (Hartman et al. 2008; Patruno 2010; Riggio et al. 2011). This frequency change is most likely driven by the neutron star's loss of rotational energy. If so, then the spin-down luminosity is given as Equation (6) where I represents the neutron star moment of inertia. The long-term spin-down of a neutron star is usually assumed to be dominated by the braking torque associated with a spinning magnetic field. Assuming this mechanism is responsible for the observed spin-down in Swift J1756, we can compute the magnetic dipole moment as (Spitkovsky 2006) Equation (7) where α is the misalignment angle between the rotational and magnetic poles. Considering α = 0°–90°, we then find a magnetic field strength of $B\simeq (4\mbox{--}6)\times {10}^{8}$ G at the stellar magnetic poles. This magnetic field strength estimate is in line with those obtained for other accreting millisecond pulsars (see Mukherjee et al. 2015 and references therein). 4.2. Orbit Evolution The observed long-term binary evolution of Swift J1756 is consistent with this source having a constant orbital period and a lower limit on the evolutionary timescale of Equation (8) Binary evolution theory predicts that systems of this type evolve due to angular momentum loss through gravitational radiation (Kraft et al. 1962; Rappaport et al. 1982; Verbunt 1993). For conservative mass transfer, the binary period derivative is given by di Salvo et al. (2008), Equation (9) where MNS is the neutron star mass, $q={M}_{C}/{M}_{\mathrm{NS}}$ is the binary mass ratio, and −1/3 < n < 1 is the mass–radius index of the companion star. Depending on the source inclination, Krimm et al. (2007b) derived a companion mass of ${M}_{C}\,=0.007\mbox{--}0.022\,{M}_{\odot }$ for a neutron star mass of 1.4 ${M}_{\odot }$. For a neutron star mass of 2.2 ${M}_{\odot }$, the allowed range increased to ${M}_{C}=0.009\mbox{--}0.030\,{M}_{\odot }$. In both cases, they assumed an upper limit on the inclination of i < 85°, motivated by the fact that Swift J1756 does not show eclipses in its light curve. Accounting for the extreme cases of stellar masses and n, the binary may either be contracting or expanding. In either case, however, the rate of change is limited to $| {\dot{P}}_{b}| \lesssim 7\times {10}^{-14}$ s s−1, which is well below the upper limit obtained in this work. Although the binary evolution timescale we obtain for Swift J1756 is consistent with theory, it is worth noting that this is not generally true for low-mass X-ray binaries (see Patruno et al. 2017, for a comprehensive discussion). The AMXP SAX J1808.4–3658, in particular, has been found to evolve on a much shorter timescale, with a first derivative on the orbital period of $3.5\times {10}^{-12}$ s s−1 (Hartman et al. 2008; Patruno et al. 2012; Sanna et al. 2017a). Two models have been proposed to explain this discrepancy: highly nonconservative mass transfer due to irradiation of the companion star by the pulsar (di Salvo et al. 2008; Burderi et al. 2009), and spin–orbit coupling in the companion star (Hartman et al. 2008, 2009). While the latter depends on the companion star, and may vary from source to source, the former should operate in all AMXPs (see also Patruno 2017; Sanna et al. 2017c), including Swift J1756. The spin-down luminosity impinging on the companion star can be estimated as Equation (10) where ${\dot{E}}_{\mathrm{abl}}$ is the ablation luminosity, RL2 is the Roche lobe radius of the companion (Eggleton 1983), and a the binary separation. The irradiation fraction is $f={\dot{E}}_{\mathrm{abl}}/{\dot{E}}_{\mathrm{sd}}$, which, accounting for the range of allowed neutron star and companion masses, evaluates to f = 0.15%–0.35%. The associated mass loss for the companion is given by Equation (11) such that, assuming an efficiency of η = 100%, ${\dot{M}}_{C}\,\sim -3\times {10}^{-10}\,{M}_{\odot }$ yr−1. The effect of this mass loss on the orbital period follows through the relation (Frank et al. 2002) Equation (12) giving a period derivative due to mass loss of ${\dot{P}}_{b,\mathrm{ML}}\,=5\times {10}^{-12}$ s s−1. This value is well above our limit on the period derivative. Hence, in order for this mechanism to be consistent with our observations of Swift J1756, the efficiency at which the companion star converts the incident luminosity into mass loss must be η < 15%. This value is very different from the 40% required in SAX J1808.4–3658 (Patruno et al. 2016) and is instead in line with the <5% efficiency determined for IGR J00291+5934 (Patruno 2017). This work was supported by NASA through the NICER mission and the Astrophysics Explorers Program, and made use of data and software provided by the High Energy Astrophysics Science Archive Research Center (HEASARC). P.B. was supported by an NPP fellowship at NASA Goddard Space Flight Center. D.A. acknowledges support from the Royal Society.

Bult, Peter↗

Switched-Polarization Birefringent Optical Delay Lines

Controllable birefringent optical delay lines proposed for use in photonically controlling phases of signals in radiating elements of phased-array antennas. Features low optical insertion losses and made very compact, enabling high packing densities where multiple delay channels needed. Polarization switched in segments to adjust overall delay. Furthermore, two or more delay lines cascaded increases delay-adjustment range.

Yao, Xiaotian Steve↗

Performance analysis and simulation of the SPS reference phase control system

The major elements required in the operation of an SPS which employs retrodirectivity as a means of pointing the beam to Earth include the spacetenna, the rectenna, and the pilot signal transmitter. The phase control system is faced with several problems: (1) path delay variations due to imperfect SPS circular orbits; (2) ionospheric effects; (3) initial phase beam forming; (4) beam pointing; (5) beam safing; (6) high power phase noise effects; and (7) interference. The use of SOLARISM, a computer program to select pilot signal parameters and evaluate SPS performance is described.

Lindsey, W. C.↗

ATD-2 Field Evaluation of Pre-Departure Trajectory Option Set Reroutes in North Texas Metroplex

The NASA Airspace Technology Demonstration-2 Phase 3 capabilities extend Integrated Arrival, Departure and Surface scheduling to a Metroplex environment where multiple airports are interacting and sharing resources along the terminal boundary. The Phase 3 coordinated scheduling provides pre-departure reroute recommendations to flight operators which reduce delay caused by terminal restrictions. This paper reports results of the Phase 3 Stormy 2021 Field Evaluation conducted between November 2020 and September 2021 in the North Texas Metroplex. During the field evaluation NASA partnered with the FAA, American Airlines, Southwest Airlines, and Envoy Airlines to evaluate Phase 3 capabilities in an operational environment. The benefits results are provided as delay savings metrics measured in time and converted to fuel and emissions savings using detailed fuel flow models provided by flight operators.

ATD-2 Field Evaluation, Trajectory Option Set, Pre↗

ATD-2 Field Evaluation of Pre-Departure Trajectory Option Set Reroutes in North Texas Metroplex

The NASA Airspace Technology Demonstration-2 Phase 3 capabilities extend Integrated Arrival, Departure and Surface scheduling to a Metroplex environment where multiple airports are interacting and sharing resources along the terminal boundary. The Phase 3 coordinated scheduling provides pre-departure reroute recommendations to flight operators which reduce delay caused by terminal restrictions. This paper reports results of the Phase 3 Stormy 2021 Field Evaluation conducted between November 2020 and September 2021 in the North Texas Metroplex. During the field evaluation NASA partnered with the FAA, American Airlines, Southwest Airlines, and Envoy Airlines to evaluate Phase 3 capabilities in an operational environment. The benefits results are provided as delay savings metrics measured in time and converted to fuel and emissions savings using detailed fuel flow models provided by flight operators.

ATD-2↗