Search NASA⌕ Search

SEARCH · Search NASA

Results for “processing parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Slot-die-coating operability windows for polymer electrolyte membrane fuel cell cathode catalyst layers

Roll-to-roll (R2R) slot-die coating of polymer electrolyte membrane fuel cell (PEMFC) catalyst layers represents a scalable deposition method for producing 10–20 m 2 ·min -1 of catalyst-coated gas diffusion layers (GDLs). This high-throughput production technique will help lower the cost of PEMFC catalyst layers. The uniformity of the wet layer applied by slot die deposition is affected by process parameters such as substrate speed, vacuum pressure applied at the upstream meniscus, gap between the slot die lips and substrate, ink rheology, and other ink and substrate properties. The set of conditions for producing a defect-free coating with a dilute ink typically requires little to no upstream vacuum pressure, so suitable operating conditions can be found easily through trial and error and operator intuition. However, the higher viscosity of more concentrated inks dramatically shifts the range of settings that result in a homogeneous coating to higher vacuum levels, which are harder to find through hit or miss. A predictive model showing the range of operable conditions decreases material wastage inherent in experimentally searching for suitable parameters. In this study, the defect-free coating parameter window is explored experimentally and theoretically for two concentrations of PEFC cathode inks. Both a full capillary hydrodynamic model and a computationally cheaper viscocapillary model successfully predict the experimentally determined coating window within the experimental and model uncertainty limits for inks with 5.3 wt% and 12.0 wt% solids ink while maintaining the 0.1 mg Pt ·cm -2 Pt areal loading target. Here, this paper demonstrates a viable pathway for meeting the $30/kW net ultimate cost target of the United States Department of Energy (U.S. DOE) Hydrogen Fuel Cells Technologies Office (HFTO). The concentrated ink lowers the thermal energy and capital expenditure (CapEx) budget of the coating process by decreasing the amount of time, energy, and floorspace required for drying the coating.

25 ENERGY STORAGE↗
DOE OSTI2021

Effect of Temperature on the Pilot-Scale Catalytic Pyrolysis of Loblolly Pine

A pilot-scale biomass catalytic pyrolysis unit with a nominal throughput of one tonne of biomass per day (1TPD) has been in operation since 2013 to investigate the process parameters that have the largest influence on biocrude yield, oxygen content, and chemical composition. A parametric study was conducted to investigate the effect of pyrolysis temperature, ranging from 433 to 581 °C, on biocrude yield and quality. A locally sourced loblolly pine feedstock and a commercially available, spray dried, nonzeolitic γ-Al 2 O 3 catalyst were used in individual experiments conducted at each pyrolysis temperature to achieve a minimum of 4 h of steady-state continuous operation. Typically, 600–800 kg of biomass was fed over a 12-h period, with one experiment extended to almost 29 h (1144-kg biomass fed) and one experiment interrupted by a process upset after just 7 h (411-kg biomass fed). Comprehensive analysis of collected gas, liquid, and solid products were used to calculate carbon balances (77% to 107%) for each experiment. The biocrude yield ranged from 12 to 18 wt % C and, in general, decreased with increasing pyrolysis temperature. The average steady-state biocrude yield as a function of temperature translated to a biocrude production rate between 40 and 50 gallons per dry ton. The biocrude oxygen content varied between 21 and 31 wt %, on a dry basis, and as expected, decreased with increasing pyrolysis temperature. The identified components in the semivolatile biocrude products are mostly methoxyphenols and other multiphenolic compounds. The multiphenolic compounds are demethoxylated at pyrolysis temperatures above 500 °C, producing biocrudes with higher concentrations of monophenols and polycyclic aromatic hydrocarbons. The concentration of anhydrosugars, like levoglucosan in the biocrudes, decreased with increasing pyrolysis temperature from ∼15 to ∼1 vol %.

biofuels↗
DOE OSTI2024

Theory-guided design of duplex-phase multi-principal-element alloys

Density-functional theory (DFT) is used to identify phase-equilibria in multi-principal-element and high-entropy alloys (MPEAs/HEAs), including duplex-phase and eutectic microstructures. Here, a combination of composition-dependent formation energy and electronic-structure-based ordering parameters were used to identify a transition from FCC to BCC favoring mixtures, and these predictions experimentally validated in the Al-Co-Cr-Cu-Fe-Ni system. A sharp crossover in lattice structure and dual-phase stability as a function of composition were predicted via DFT and validated experimentally. The impact of solidification kinetics and thermodynamic stability was explored experimentally using a range of techniques, from slow (castings) to rapid (laser remelting), which showed a decoupling of phase fraction from thermal history, i.e., phase fraction was found to be solidification rate-independent, enabling tuning of a multi-modal cell and grain size ranging from nanoscale through macroscale. Strength and ductility tradeoffs for select processing parameters were investigated via uniaxial tension and small-punch testing on specimens manufactured via powder-based additive manufacturing (directed-energy deposition). This work establishes a pathway for design and optimization of next-generation multiphase superalloys via tailoring of structural and chemical ordering in concentrated solid solutions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Process Variability Effects on Tensile Response in Injection Molded, Fluorinated Thermoplastics

The mechanical properties of fluorinated thermoplastics (i.e., tensile strength and elongation) can vary with changes in injection molding processing parameters. Four fluoropolymers are examined: poly(vinylidene fluoride) (PVDF) and random poly(vinylidene fluoride-co-chlorotrifluoroethylene) (PVDF-CTFE) with three CTFE concentrations. Dog bones were manufactured with various cylinder dwell times and mold cooling times to assess the manufacturing sensitivity to the tensile response. Dwell and cooling times increasingly impact mechanical performance as CTFE concentration increases. Specimens exhibit higher tensile strength as a function of injection order. The first injected specimen exhibits the lowest tensile strength and highest elongation in all copolymers. This trend becomes more pronounced among fluoropolymers with higher CTFE concentration and lower weight-averaged molecular weight. Parallel plate rheology was used to obtain the zero-shear viscosity as a function of material type, process, and injection order. We found that in the copolymers, the first injected sample exhibited a lower zero-shear viscosity than the next, which indicates a lower molecular weight in the first injected specimen. This phenomenon was not presented for the PVDF homopolymer. Copolymer mechanical uncertainties are hypothesized to result from the shorter molecular weight chains extruding out of the specimens' sides as a flash due to higher mobility with CTFE segments.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Process Variability Effects on Tensile Response in Injection Molded, Fluorinated Thermoplastics

The mechanical properties of fluorinated thermoplastics (i.e., tensile strength and elongation) can vary with changes in injection molding processing parameters. Four fluoropolymers are examined: poly(vinylidene fluoride) (PVDF) and random poly(vinylidene fluoride-co-chlorotrifluoroethylene) (PVDF-CTFE) with three CTFE concentrations. Dog bones were manufactured with various cylinder dwell times and mold cooling times to assess the manufacturing sensitivity to the tensile response. Dwell and cooling times increasingly impact mechanical performance as CTFE concentration increases. Specimens exhibit higher tensile strength as a function of injection order. The first injected specimen exhibits the lowest tensile strength and highest elongation in all copolymers. This trend becomes more pronounced among fluoropolymers with higher CTFE concentration and lower weight-averaged molecular weight. Parallel plate rheology was used to obtain the zero-shear viscosity as a function of material type, process, and injection order. We found that in the copolymers, the first injected sample exhibited a lower zero-shear viscosity than the next, which indicates a lower molecular weight in the first injected specimen. This phenomenon was not present for the PVDF homopolymer. Copolymer mechanical uncertainties are hypothesized to result from the shorter molecular weight chains extruding out of the specimens’ sides as a flash due to higher mobility with CTFE segments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Adsorptive denitrogenation of model aviation fuel using mesoporous silica in a packed bed adsorption system

This study aims to understand the effects of system process parameters such as flow rate, adsorbent particle size, and use of recycled adsorbent on denitrogenation performance of a model fuel using mesoporous silica gel. The goal is to reduce the nitrogen content of the model fuel from 1500 parts per million to single-digit ppm to meet ASTM specifications for drop-in fuels. This work was done with the intent of applying adsorptive denitrogenation to sustainable aviation fuel (SAF) product fractions produced via hydrothermal liquefaction (HTL). The adsorption performance of the silica is evaluated via packed column breakthrough data, with data generated from collecting from the column outlet and quantifying nitrogen content via gas chromatography. Select experiments use a significantly larger (2.5x column diameter and length) column to demonstrate linear scalability of the process. Thermogravimetric analysis data is collected to evaluate the effects of thermal calcination as a sorbent regeneration method. Effects of a more complex feed are also investigated using a known reference fuel with additional added nitrogen containing compounds. The results presented in this work successfully demonstrate up to 99.8 % removal of NCCs from a model fuel fraction at an original NCC concentration of approximately 1500 ppm to single-digit parts per million after treatment. We also examine calcination of sorbent materials to remove the adsorbed species to enable sorbent reuse and minimize waste generation and show that the calcined material can be reused up to 5 cycles with reduced adsorption capacity. Overall, this work indicates that adsorptive denitrogenation using silica gel is a viable solution to enable the integration of HTL-derived aviation fuels into existing fuel infrastructure.

Adsorption techniques↗
DOE OSTI2024

Dissolution zone model of the oxide structure in additively manufactured dispersion-strengthened alloys

The structural evolution of oxides in dispersion-strengthened superalloys during laser-powder bed fusion is considered in detail. Alloy chemistry and process parameter effects on oxide structure are assessed through a parameter study on the model alloy Ni-20Cr, doped with varying concentrations of Y 2 O 3 and Al. Small angle neutron scattering measurements of the dispersoid size distribution show the dispersoid size increases with higher laser power, slower scan speed, and increasing Y 2 O 3 and Al content. Complementary electron microscopy measurements reveal reactions between Y 2 O 3 and Al, even in nanoscale dispersoids, and the presence of micron-scale oxide slag inclusions in select specimens. A scaling analysis of mass and momentum transport within the melt pool, presented here, establishes that diffusional structural evolution mechanisms dominate for nanoscale dispersoids, while fluid forces and advection become significant for larger slag inclusions. These findings are developed into a theory of dispersoid structural evolution, integrating quantitative models of diffusional processes – dispersoid dissolution, nucleation, growth, coarsening – with a reduced order model of time-temperature trajectories of fluid parcels within the melt pool. Calculations of the dispersoid size in single-pass melting reveal a zone in the center of the melt track in which the oxide feedstock fully dissolves. Within this zone the final Y 2 O 3 size is independent of feedstock size and determined by nucleation and growth kinetics. If the dissolution zones of adjacent melt tracks overlap sufficiently with each other to dissolve large oxides, formed during printing or present in the powder feedstock, then the dispersoid structure throughout the build volume is homogeneous and matches that from a single pass within the dissolution zone. Gaps between adjacent dissolution zones result in oxide accumulation into larger slag inclusions. Predictions of final dispersoid size and slag formation using this dissolution zone model match the present experimental data and explain process-structure linkages speculated in the open literature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Computational fluid dynamics modeling and analysis of silica nanoparticle synthesis in a flame spray pyrolysis reactor

Flame Spray Pyrolysis (FSP) is a method for large-scale production of nanoparticles and nanoscale powders employed in a wide range of industrial applications. Particle size and morphology are complex functions of the physicochemical phenomena occurring in the FSP reactor. An extensive study of FSP-related phenomena can be utilized to develop effective strategies for achieving desired particle size/morphology and scaling up the overall yield of an FSP system. In this work, a computational fluid dynamics (CFD) model of an FSP reactor is developed to simulate the coupling of key phenomena involved in the particle synthesis process: liquid spray breakup and evaporation, mixing, combustion, and particle formation/growth of silica nanoparticles. Herein, the particle sizes and their distributions from the CFD simulations are validated against experimental data. Subsequently, the simulations are utilized to investigate the impact of process parameters on the resultant flame dynamics and particle growth. Firstly, the CFD results show that the particle sizes are strongly correlated with the precursor concentration in the solvent. At lower precursor concentrations, the spread of the distribution is relatively insensitive to the value of the concentration. At higher concentrations, the spread is higher as the collision probability between particles is higher. Secondly, increasing the pilot flow rate increases the length of the pilot flames impacting the local ignition location of the spray flame. Lastly, it is shown that the dispersion gas flow rate strongly influences the spray flame shape. This shape can be used for control of particle growth as it helps determine the regions of high temperature and the residence time of the particles in the high temperature region enabling the design and process optimization of the FSP reactor.

42 ENGINEERING↗
DOE OSTI2024

Very high cycle fatigue characteristics of laser beam powder bed fused AlSi10Mg: A systematic evaluation of part geometry

This study explores the influence of geometry and part size on defect distribution, melt pool size, and mechanical characteristics in laser beam powder bed fused (LB-PBF) AlSi10Mg. Five distinct geometries—hourglass, small rod, small block, large block, and large rod—were fabricated under identical process parameters. Fully reversed ultrasonic fatigue testing, operating at a frequency of 20 kHz, was conducted to assess the very high cycle fatigue properties. The findings indicated that part geometry had a major impact on the fatigue properties of the material in the very high cycle fatigue regime. Specimens machined from large rods and large blocks had the lowest porosity and highest fatigue resistance. Microstructural analysis indicated that hourglass, small rod, and small block specimens had shallower melt pools and overlap depths compared to other geometries. This observation suggests a higher cooling rate in specimens with smaller cross-sectional areas, leading to the increased presence of entrapped gas pores and a lack of fusion defects. Understanding the relationship between part geometry and fatigue properties in LB-PBF components offers insights for optimizing design and manufacturing processes in additive manufacturing applications.

AlSi10Mg↗
DOE OSTI2024

Lifetime Energy Savings Via Advanced Manufacturing of Low Density Steels for Transportation Applications

The purpose of this “Low Density Steels for Transportation Applications” project was to develop an alloy composition and processing parameters that would result in a material suitable for use in automotive structural components at a reduced density over the current advanced high strength steel (AHSS) materials used. The project work successfully developed a robust alloy capable of exceeding project mechanical property targets at each stage of development, with an 8% density reduction over benchmark AHSS materials (7.8 g/cm3). The developed alloy has the potential to offer significant vehicle lightweighting and improved fuel economy, without sacrificing the increased passenger safety of more traditional AHSS. Through the three tasks of the project, (1) Alloy design and small-scale laboratory evaluation, (2) Laboratory development of hot rolled material and (3) Laboratory development of a cold rolled material, the laboratory work utilized advanced characterization and analytical methods on novel alloy compositions subjected to both conventional and non-conventional processing operations.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Focused ion beam milling of polycrystalline diamond

Focused ion beam (FIB) technology has a large potential for precise milling of ultrahard materials such as diamond. However, studies of the sputtering of diamond with ion species and energies relevant to the FIB technology are scarce. Here, we report a systematic study of the sputtering of polycrystalline diamond surfaces with ion beams in a wide range of ion energies (2 - 30 keV), incident beam angles (0 - 80°), and ion masses (N, O, Ar, and Xe). Results show that the sputter yield is relatively insensitive to ion energy but strongly depends on the ion species and incident beam angles. Bombardment with O ions results in sputter yields that are significantly larger than ballistic predictions due to chemical etching effects. Characteristic surface ripples develop for oblique beam incidence angle irradiation. The critical beam tilt angle for the onset of ripple formation and the wavelength of the ripples depend on ion species and energies. Ripples appear to suppress ion reflection at high beam tilt angles and, hence, a peak in the sputter yield angular dependence. In conclusion, these results have direct implications for the development of process parameter maps for high-precision ion-beam milling of diamond.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fabrication of Silicon Sensors Based on Low-Gain Avalanche Diodes

Low-Gain Avalanche Diodes are a recently-developed class of silicon sensors. Characterized by an internal moderate gain that enhances the signal amplitude and if built on thin silicon substrates of a few tens of microns, they feature fast signals and exhibit excellent timing performance. Thanks to their fast timing they are planned to be exploited in timing detectors in High-Energy Physics experiments, for example for the upgrades of the ATLAS and CMS detectors at the High Luminosity Large Hadron Collider (HL-LHC) at CERN. However, to achieve a spatially uniform multiplication a large pixel pitch is needed, preventing a fine spatial resolution. To overcome this limitation, the AC-coupled LGAD approach was introduced. In this type of device, metal electrodes are placed over an insulator at a fine pitch, and signals are capacitively induced on these electrodes. The fabrication technology is similar for the two LGAD families, although a fine tuning of a few process parameters needs to be carefully studied. Other R&D efforts towards detectors that can simultaneously provide good time and spatial resolution, based on the LGAD concept, are under way. These efforts aim also to mitigate the loss of performance at high irradiation fluences due to the acceptor removal within the gain layer. In this paper we describe the main points in the fabrication of LGADs and AC-LGADs in a clean-room. We also discuss novel efforts carried on related topics.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Optimizing high energy density sulfur cathodes: A multivariate approach to electrode formulation and processing

Lithium-sulfur (Li-S) batteries involve complex solid-liquid-solid phase transformations during both discharging and charging processes, where cathode materials, formulation, and structure play a crucial role. Here, a design of experiments (DoE) methodology and an empirical model are developed to systematically explore the interactions and trade-offs among cathode factors and process variables, and to obtain generalizable effects estimates for the multivariate system. Compared to the conventional one-factor-at-a-time (OFAT) approach, this work demonstrates advantages in both efficiency and accuracy by allowing the data to guide future research and decisions. Further, an optimized cathode formulation and processing parameters are predicted and validated experimentally, achieving over 1000 mAh g -1 in discharge capacity and improved cycling under practical lean electrolyte (4 µL mg -1 S) and high S-loading cathodes (>4 mg cm -2 ) conditions. The optimized cathode was scaled up and assembled into Li-S pouch cells, achieving 316 Wh kg -1 in cell-level energy, proving that the comprehensive and rigorous framework for optimizing complex systems with DoE leads to improved performance in a practical pouch cell system.

25 ENERGY STORAGE↗
DOE OSTI2024

Selective Deposition and Fusion of AISI 316L: An Additive Manufacturing Process for Space Environments via Direct Ink Writing and Laser Processing

Unlocking the potential of additive manufacturing (AM) for space exploration hinges on overcoming key challenges, notably the ability to manufacture or repair parts on-site during exploration missions with consideration of quality, feedstock utilization, and challenges involved in microgravity environments. While there are multiple efforts to investigate the use of existing metal AM processes such as powder bed fusion (PBF), directed energy deposition (DED), and filament-based material extrusion, each process comes with a different set of challenges in space environments. Here, in this work, we introduce a new AM method that integrates the benefits of direct ink writing (DIW) to selectively deposit metallic pastes with laser-based processing to locally debind and subsequently melt and fuse metal powder, layer by layer, enabling the manufacturing of AISI 316L samples with densities exceeding 99.0%. The impact of process parameters on single-track dimensions, surface morphology, and porosity was characterized. The efficacy of laser debinding was assessed via secondary-ion mass spectrometry, permitting the carbon content to be estimated at 0.0152%, which is safely below the acceptable limit (0.03 wt%) for AISI 316L.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of tool design and pass strategy on defect elimination and uniform, enhanced tensile properties of friction stir processed high-pressure die-cast A380 alloy

This work reports implementation of friction stir processing (FSP) to locally modify microstructure and create a defect-free processing zone with the aid of different tool designs and altering the passing strategy for two different process parameter combinations. Here, FSP is applied on high pressure die-cast (HPDC) A380 alloy, a widely used Al-Si alloy fabricated in the die casting sector for automotive and aerospace applications. However, the presence of gas and shrinkage porosity, brittle needle-shaped Fe-containing ß-FeSiAl 5 intermetallic compounds, Al-dendrites, coarse and acicular silicon particles, and large second-phase particulates have a detrimental influence on the uniformity of tensile properties across the thickness direction of an HPDC plate. FSP is able to eliminate porosity, refine microstructure and improve tensile properties. An FSP tool design and a passing strategy are identified for the best microstructure consolidation and uniform enhanced tensile properties. This study noted the importance of tool features such as scroll design and flats on tool pin and multiple pass orientation strategy to find best combination of defect-free refined microstructure and uniform tensile strength and ductility across the processing zone of HPDC Al alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Directed energy deposition of radially functionally graded nickel based superalloys IN625 and IN738: Microstructure and mechanical properties

This study investigates the microstructure and mechanical properties of radially functionally graded (RFG) materials fabricated from nickel-based superalloys IN625 and IN738 using directed energy deposition (DED). RFG cylindrical deposits with radial gradients of IN625-IN738 and IN738-IN625 were successfully fabricated and confirmed to be crack-free through tailored composition grading, scan strategy and process parameters that minimized thermal gradients and solidification velocities. Microstructural analysis revealed distinct variations across the gradient, characterized by differences in dendrite arm spacing, microsegregation, and the formation of distinct γ' precipitates and carbide/boride phases (MC, M 6 C, M 2 C, and MB 2 ) in as-deposited (AD) conditions, which evolved into M 23 C 6 and M 2 B upon subsequent heat treatment (HT). EBSD showed predominant columnar grains with a [100] texture, while microhardness profiles demonstrated consistent variation across the gradients. Mechanical testing highlighted the synergy of the graded structure, combining IN738's strength with IN625's ductility, resulting in enhanced properties such as a yield strength of 1131 MPa, ultimate tensile strength of 1382 MPa, and elongation of 12 % for HT IN625-IN738 grading. Numerical simulations employing CALPHAD thermodynamic calculations and finite element thermal modeling are used to establish phase evolution and microstructural feature correlation with thermal profiles, aiding in the optimization of process-structure-property relationship.

Additive manufacturing↗
DOE OSTI2026

Enabling Bipolar Membrane Manufacturing Using Microscopy

Bipolar membranes (BPMs) used for water treatment suffer from interface instabilities, causing premature failure and decreased performance. Recent research has highlighted the impacts of membrane morphology on mechanical behavior and performance. Improved material performance of thin film membranes requires enhanced transport properties coupled with better control of the mechanical characteristics to avoid premature failure of the film. Thus, morphology is a key parameter when developing and evaluating novel membrane materials. Microscopy offers unique advantages for nano-scale characterization of thin film membrane interfaces and morphologies. In this study, the interface junction of BPMs was evaluated using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). BPMs were fabricated using (1) hot pressing lamination, (2) bench-scale solution casting, and (3) roll-to-roll sequential casting (R2R). Both commercial and in-house fabricated ion exchange membranes were used in the BPMs. The BPMs were comprised of a cation exchange membrane and an anion exchange membrane with a catalyst layer sandwiched in between. Cross sectional SEM and EDX images of the membrane interface junction were compared among the different fabrication techniques and materials. The bench cast catalyst layers were nonuniform compared to the R2R and hot pressed membranes, demonstrating the importance of precise catalyst application conditions. Different thicknesses of the BPMs and individual membrane layers revealed that polymer solution concentration needs to be optimized during manufacturing. This work shows that microscopy can identify key processing parameters that affect BPM interface junction quality at the microscale to enable manufacturing of high performance BPMs.

36 MATERIALS SCIENCE↗