Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Heat Transfer Variation on Protuberances and Surface Roughness Elements

In order to determine the effect of surface irregularities on local convective heat transfer, the variation in heat transfer coefficients on small (2-6 mm diam) hemispherical roughness elements on a flat plate has been studied in a wind funnel using IR techniques. Heat transfer enhancement was observed to vary over the roughness elements with the maximum heat transfer on the upstream face. This heat transfer enhancement increased strongly with roughness size and velocity when there was a laminar boundary layer on the plate. For a turbulent boundary layer, the heat transfer enhancement was relatively constant with velocity, but did increase with element size. When multiple roughness elements were studied, no influence of adjacent roughness elements on heat transfer was observed if the roughness separation was greater than approximately one roughness element radius. As roughness separation was reduced, less variation in heat transfer was observed on the downstream elements. Implications of the observed roughness enhanced heat transfer on ice accretion modeling are discussed.

Henry, Robert C.↗

Light scattering by a rough surface of human skin. 1. The luminance factor of reflected light

Based on the analytical solution of Maxwell's equations, we have studied the angular structure of the luminance factor of light reflected by the rough skin surface with large-scale relief elements, illuminated by a directed radiation beam incident at an arbitrary angle inside or outside the medium. The parameters of the surface inhomogeneities are typical of human skin. The calculated angular dependences are interpreted from the point of view of the angular distribution function of micro areas. The results obtained can be used for solving direct and inverse problems in biomedical optics, in particular for determining the depth of light penetration into a biological tissue, for studying the light action spectra on tissue chromophores under the in vivo conditions, for developing diagnostic methods of structural and biophysical parameters of a medium, and for optimising the mechanisms of interaction of light with biological tissues under their noninvasive irradiation through skin. (biomedical optics)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Venus surface roughness and Magellan stereo data

Presented are results of some studies to develop tools useful for the analysis of Venus surface shape and its roughness. Actual work was focused on Maxwell Montes. The analyses employ data acquired by means of NASA's Magellan satellite. The work is primarily concerned with deriving measurements of the Venusian surface using Magellan stereo SAR. Roughness was considered by means of a theoretical analyses based on digital elevation models (DEM's), on single Magellan radar images combined with radiometer data, and on the use of multiple overlapping Magellan radar images from cycles 1, 2, and 3, again combined with collateral radiometer data.

Maurice, Kelly E.↗

Influence of surface roughness on the efficiency of X-ray mirrors with whispering gallery modes

The influence of roughness on the propagation of an X-ray beam along a concave surface in the whispering gallery mode has been investigated. The transfer equation of beam intensity is derived and the conditions of concave surface smoothness necessary for effective beam rotation are obtained. It is shown that the influence of roughness on the beam rotation efficiency is not very strong: the roughness height should not exceed several nanometers. The point is that the scattered radiation is not lost but rotated by a concave surface and makes a significant contribution to the intensity of the output beam.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Wind-Tunnel Investigations of Blunt-Body Drag Reduction Using Forebody Surface Roughness

This paper presents results of wind-tunnel tests that demonstrate a novel drag reduction technique for blunt-based vehicles. For these tests, the forebody roughness of a blunt-based model was modified using micomachined surface overlays. As forebody roughness increases, boundary layer at the model aft thickens and reduces the shearing effect of external flow on the separated flow behind the base region, resulting in reduced base drag. For vehicle configurations with large base drag, existing data predict that a small increment in forebody friction drag will result in a relatively large decrease in base drag. If the added increment in forebody skin drag is optimized with respect to base drag, reducing the total drag of the configuration is possible. The wind-tunnel tests results conclusively demonstrate the existence of a forebody dragbase drag optimal point. The data demonstrate that the base drag coefficient corresponding to the drag minimum lies between 0.225 and 0.275, referenced to the base area. Most importantly, the data show a drag reduction of approximately 15% when the drag optimum is reached. When this drag reduction is scaled to the X-33 base area, drag savings approaching 45,000 N (10,000 lbf) can be realized.

Whitmore, Stephen A.↗

Radar mapping of lunar surface roughness.

Comparison of anomalous behavior at infrared and radar wavelengths provides an estimation of lunar surface structure at centimeter-to-meter sizes. Although a simple classification is used, it is shown that the combination of the infrared and radar data contains more information than any of the sets by themselves. The infrared data indicate that bare surface rocks are the source of the roughness which generates enhanced radar backscatter. The different radar maps indicate the size of surface rocks, as was demonstrated for the strewn fields of centimeter-sized rubble (the Type II anomaly). As craters age, they have a rim-bright appearance in the radar maps, and eventually lose their anomalous-behavior at infrared and 3.8-cm radar wavelengths.

Thompson, T. W.↗

Cleanliness evaluation of rough surfaces with diffuse IR reflectance

Contamination on bonding surfaces has been determined to be a primary cause for degraded bond strength in certain solid rocket motor bondlines. Hydrocarbon and silicone based organic contaminants that are airborne or directly introduced to a surface are a significant source of contamination. Diffuse infrared (IR) reflectance has historically been used as an effective technique for detection of organic contaminants, however, common laboratory methods involving the use of a Fourier transform IR spectrometer (FTIR) are impractical for inspecting the large bonding surface areas found on solid rocket motors. Optical methods involving the use of acousto-optic tunable filters and fixed bandpass optical filters are recommended for increased data acquisition speed. Testing and signal analysis methods are presented which provide for simultaneous measurement of contamination concentration and roughness level on rough metal surfaces contaminated with hydrocarbons.

Pearson, L. H.↗

Rough Surfaces: Is the Dark Stuff Just Shadow?: "Who knows what evil lurks in the hearts of men? The shadow knows!"

Remote observations of the surfaces of airless planetary objects are fundamental to inferring the physical structure and compositional makeup of the surface material. A number of forward models have been developed to reproduce the photometric behavior of these surfaces, based on specific, assumed structural properties such as macroscopic roughness and associated shadowing. Most work of this type is applied to geometric albedos, which are affected by complicated effects near zero phase angle that represent only a tiny fraction of the net energy reflected by the object. Other applications include parameter fits to resolved portions of some planetary surface as viewed over a range of geometries. The spherical albedo of the entire object (when it can be determined) captures the net energy balance of the particle more robustly than the geometric albedo. In most treatments involving spherical albedos, spherical albedos and particle phase functions are often treated as if they are independent, neglecting the effects of roughness. In this paper we take a different approach. We note that whatever function captures the phase angle dependence of the brightness of a realistic rough, shadowed, flat surface element relative to that of a smooth granular surface of the same material, it is manifested directly in both the integral phase function and the spherical albedo of the object. We suggest that, where broad phase angle coverage is possible, spherical albedos may be easily corrected for the effects of shadowing using observed (or assumed) phase functions, and then modeled more robustly using smooth-surface regolith radiative transfer models without further imposed (forward-modeled) shadowing corrections. Our approach attributes observed "power law" phase functions of various slope (and "linear" ranges of magnitude-vs.-phase angle) to shadowing, as have others, and goes on to suggest that regolith-model-based inferences of composition based on shadow-uncorrected spherical albedos overestimate the amount of absorbing material contained in the regolith.

geometric albedos↗

A possibility of avoiding surface roughness due to insects

Discussion of a method for eliminating turbulence caused by the formation of insect roughness upon the leading edges and fuselage, particularly in aircraft using BLC. The proposed technique foresees the use of elastic surfaces on which insect roughness cannot form. The operational characteristics of highly elastic rubber surface fastened to the wing leading edges and fuselage edges are examined. Some preliminary test results are presented. The technique is seen to be advantageous primarily for short-haul operations.

Wortmann, F. X.↗

ICP etching of GaN microstructures in a Cl 2 –Ar plasma with subnanometer-scale sidewall surface roughness

In this work, substrate temperature, RF power, and ICP power were investigated for their effects on GaN micropillar sidewall roughness and etch characteristics. Elevated substrate temperature was shown to improve the sidewall etch morphology at low RF powers (reduced physical bombardment) and low ICP powers (lower plasma densities). Increased lateral etching is observed with both increased ICP power and substrate temperature, which both act to increase the chemical component of the etch. Etch conditions with a high chemical driving force resulted in faceting along the a-plane on the sidewalls. This faceting produced extremely smooth surfaces with root-meansquare roughness (R q ) as low as 0.20 nm which is comparable to typical epitaxy-ready surfaces and smaller than the a-plane lattice spacing of 0.3186 nm. The smooth surfaces produced in this study enable possibilities for laser facets or for new device structures that require high quality surfaces for GaN regrowth.

36 MATERIALS SCIENCE↗

Impact of Random Micron-Sized Surface Roughness on Stationary Crossflow Instabilities

This study examines the effect of random micron-sized distributed roughness on stationary crossflow (SCF) instabilities. The roughness parameters are varied by creating nanoparticle coatings of various formulations and applying them to inserts that cover approximately the first 14% of the swept flat-plate model. In addition to the baseline configuration (no added roughness, root-mean-square (RMS) ≈ 0.4 µm ), 5 panels with RMS roughness values of 4.8 up to 17 µm and correlation lengths ranging from 92 to 876 µm were tested. Despite the significant roughness levels tested, the transition location was found to be only mildly impacted by the additional roughness. However, the SCF amplitudes and wavelength content were found to vary substantially depending on the roughness input. The results were somewhat unexpected, in that the panel with the highest roughness RMS level did not result in the largest initial amplitudes, nor did the panel with the most energy in the SCF wavelength range. Rather, the panel with the most energy in the smaller wavelengths resulted in the largest SCF amplitude. There were, however, significant variations in the results when the panels were rotated by 180 ◦ , indicating that the important factor for some of the panels may be isolated peaks that occur near the neutral point.

stationary crossflow instabilities↗

Surface roughness effects with solid lubricants dispersed in mineral oils

The lubricating effectiveness of solid-lubricant dispersions are investigated in both point and line contacts using surfaces with both random and directional roughness characteristics. Friction and wear data obtained at relatively low speeds and at room temperature, indicate that the existence of solid lubricants such as graphite, MoS2, and PTFE in a plain mineral oil generally will not improve the effectiveness of the oil as a lubricant for such surfaces. Under boundary lubrication conditions, the friction force, as a function of time, initially depends upon the directional roughness properties of the contacting surfaces irrespective of whether the base oil or dispersions are used as lubricants.

Cusano, C.↗

Surface roughness due to residual ice in the use of low power deicing systems

Thicknesses of residual ice are presented to provide information on surface contamination and associated roughness during deicing events. Data was obtained from low power ice protection systems tests conducted in the Icing Research Tunnel at NASA Lewis Research Center (LeRC) with nine different deicing systems. Results show that roughness associated with residual ice is not characterized by uniformly distributed roughness. Results also show that deicing systems require a critical mass of ice to generate a sufficient expelling force to remove the ice.

Shin, Jaiwon↗

Surface roughness due to residual ice in the use of low power deicing systems

Thicknesses of residual ice are presented to provide information on surface contamination and associated roughness during deicing events. Data was obtained from low power ice protection systems tests conducted in the Icing Research Tunnel at NASA Lewis Research Center (LeRC) with nine different deicing systems. Results show that roughness associated with residual ice is not characterized by uniformly distributed roughness. Results also show that deicing systems require a critical mass of ice to generate a sufficient expelling force to remove the ice.

Shin, Jaiwon↗

Impact of Surface Roughness and Soil Texture on Mineral Dust Emission Fluxes Modeling

Dust production models (DPM) used to estimate vertical fluxes of mineral dust aerosols over arid regions need accurate data on soil and surface properties. The Laboratoire Inter-Universitaire des Systemes Atmospheriques (LISA) data set was developed for Northern Africa, the Middle East, and East Asia. This regional data set was built through dedicated field campaigns and include, among others, the aerodynamic roughness length, the smooth roughness length of the erodible fraction of the surface, and the dry (undisturbed) soil size distribution. Recently, satellite-derived roughness length and high-resolution soil texture data sets at the global scale have emerged and provide the opportunity for the use of advanced schemes in global models. This paper analyzes the behavior of the ERS satellite-derived global roughness length and the State Soil Geographic data base-Food and Agriculture Organization of the United Nations (STATSGO-FAO) soil texture data set (based on wet techniques) using an advanced DPM in comparison to the LISA data set over Northern Africa and the Middle East. We explore the sensitivity of the drag partition scheme (a critical component of the DPM) and of the dust vertical fluxes (intensity and spatial patterns) to the roughness length and soil texture data sets. We also compare the use of the drag partition scheme to a widely used preferential source approach in global models. Idealized experiments with prescribed wind speeds show that the ERS and STATSGO-FAO data sets provide realistic spatial patterns of dust emission and friction velocity thresholds in the region. Finally, we evaluate a dust transport model for the period of March to July 2011 with observed aerosol optical depths from Aerosol Robotic Network sites. Results show that ERS and STATSGO-FAO provide realistic simulations in the region.

textures↗

Investigation of the Attenuation of Plane Shock Waves Moving over very Rough Surfaces

Experimental measurements of the attenuation of plane shock waves moving over rough walls have been made in a shock tube. Measurements of the boundary-layer characteristics, including thickness and velocity distribution behind the shock, have also been made with the aid of new cal techniques which provide direct information on the local boundary-layer conditions at the rough walls. Measurements of shock speed and shock pressure ratio are presented for both smooth-wall and rough-wall flow over lengths of machined-smooth and rough strips which lined all four walls of the shock tube. A simplified theory based on Von Karman's expression for skin-friction coefficient for flow over rough walls, along with a wave-model concept and extensions to include time effects, is presented. In this theory, the shock-tube flow is assumed to be one-dimensional at all times and the wave-model concept is used to relate the local layer growth to decreases in shock strength. This concept assumes that local boundary-layer growths act as local mass-flow sinks, which give rise to expansion waves which, in turn, overtake the shock and lower its mass flow accordingly.

Huber, Paul W.↗