Search NASA⌕ Search

SEARCH · Search NASA

Results for “scanning electron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Comparison of microstructural and mechanical properties of friction stir spot welded ultra-high strength dual phase and complex phase steels

Highlights: • The microstructure and mechanical properties of FSSW of ultra high strength DP and CP steels are compared. • The stir zone (SZ) of CP steel mainly consists of bainite and martensite; no bainite is identified in the SZ of DP steel. • The cooling was not fast enough for the CP steel to suppress the effect of chemical composition on phase transformation. - Abstract: The microstructure and mechanical properties of friction stir spot welding of ultrahigh strength dual phase (DP) and complex phase (DP) steels are compared based on the experimental results. For both DP and CP steels, FSSW joints are successfully fabricated using the same process parameter set. While the microstructure of joints are characterized in detail using scanning electron microscopy, electron back scattered diffraction, and transmission electron microscopy, the mechanical property of joints are evaluated by shear tensile tests. The result of the microstructural analysis shows that the stir zone (SZ) of CP steel mainly consists of bainite and martensite, while no bainite is identified in the SZ of DP steel. The existence of bainite in the SZ of CP steel suggests that the cooling rate, which is nearly identical for both CP and DP steels, was not fast enough to suppress the effect of the alloying composition, particularly that of Mn, on the phase transformation. The result of the present study contributes to the development of solid state joining process of the ultrahigh strength steels.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Lattice rotations in precipitate free zones in an Al-Mg-Si alloy

Highlights: • Recovery processes in precipitate free zones differ from those in grain interiors. • Most precipitate free zones contain few dislocations, after deformation. • Deformation can induce large misorientations in precipitate free zones. • Some deformed precipitate free zones contain nanoscale grains. - Abstract: Scanning precession electron diffraction and automated crystal orientation mapping in a transmission electron microscope (TEM) have been applied to quantitatively study the crystal orientation of precipitate free zones (PFZs) of four GB regions in an AA6060 alloy in peak aged condition (temper T6) after uniaxial compression to 20% engineering strain. The PFZ width in the alloy was found to be w = 170 ± 40 nm. The results show that some PFZs develop significant misorientations relative to their parent grain, and represent, to the best knowledge of the authors, the first quantitative evidence of this. This misorientation may either be constant inside a particular PFZ, making it appear like a band or a very elongated subgrain, or be partitioned in discrete regions with a diameter comparable to the PFZ width, making the former PFZ into a collection of small grains. The band-like PFZ observed in this work had a misorientation relative to its parent grain of ≈ 7°, while the grain-like PFZ had grains with misorientations between ≈ 12° and ≈ 20° relative to its parent grain. The other PFZs that were observed had only limited misorientations relative to their parent grains, and had either dislocations perpendicular to the GB plane or a dislocation wall at the transition region. A general TEM study of the material at various engineering strains was also conducted and suggests that grain-like PFZs are more frequent for larger strains, indicating that the different PFZ features are likely due to different strain localisation in individual PFZs. This localisation is expected to be influenced by the orientation of the loading axis relative to crystal orientations and GB planes. It is also suggested that the different PFZ features engender different work hardening rates and possibly affect nucleation of intergranular fracture. The results support previous studies on the microstructure evolution of PFZs in age-hardenable aluminium alloys during deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Integrated three-dimensional characterization of reactive phase formation and coarsening during isothermal annealing of metastable Zn–3Mg–4Al eutectic

Microstructural instabilities associated with a metastable lamellar eutectic when exposed to an elevated temperature were analyzed in a Zn-3Mg-4Al alloy as a model system. X-ray diffraction and scanning electron microscopy showed that annealing at a temperature 43 K below the equilibrium eutectic temperature converted the metastable ternary MgZn 2 /η-Zn/β-ZnAl eutectic to a stable mixture of Mg 2 Zn 11 /η-Zn/α-Al. 3D EBSD suggested that supersaturation of η-Zn with Mg and Al eased difficulties in nucleation of Mg 2 Zn 11 and α-Al at the MgZn 2 /η-Zn phase interfaces. Quasi-in-situ X-ray nanotomography revealed that a reactive diffusion process prevailed in an early stage of annealing leading to rapid consumption of MgZn 2 for growth of Mg 2 Zn 11 and concomitant thinning and pinch-off of η-Zn lamellae. The reactive diffusion process also brought about significant and quantifiable changes in the topological characteristics of the η-Zn phase at remarkably shorter time scales compared to Rayleigh instability and Ostwald ripening mechanisms. Overall, the present results provide fresh insights on the short-term annealing effects on metastable eutectics, with relevance to structural evolution in additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Achieving superior mechanical properties: Tailoring multicomponent microstructure in AISI 9254 spring steel through a two-stage Q&P process and nanoscale carbide integration

In the pursuit of lightweight, durable steel, we have successfully developed a multicomponent structure in AISI 9254 spring steel using a two-stage quenching and partitioning (Q&P) process. The primary objective of this process was to engineer an optimized microstructure consisting of nanobainite, martensite, and nano-carbides. Utilizing the insights gained from the results of advanced techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atom probe tomography (APT) performed on the as-received AISI 9254 spring steel, we refined the quenching and partitioning (Q&P) path, leading to the successful establishment of a bainitic transformation for superior mechanical properties. Our tensile tests revealed a high yield strength (≈ 1600 ± 25 MPa) and ultimate tensile strength (≈ 1850 ± 50 MPa), along with considerable elongation (≈ 11.15 ± 0.25%). We also identified that pre-formed martensite lath defects and high silicon content play crucial roles during the Q&P process, preventing carbide coalescence and increasing strain-hardening capacity. Finally, this study demonstrates the potential of a Q&P process to generate high-strength, ductile steel for automotive and aerospace applications.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Visible-light-driven ZnFe{sub 2}O{sub 4}/Ag/Ag{sub 3}VO{sub 4} photocatalysts with enhanced photocatalytic activity under visible light irradiation

Highlights: • The ZnFe2O4/Ag/Ag3VO4 composites were successfully synthesized by a hydrothermal method. • ZnFe2O4/Ag/Ag3VO4 composites showed better photocatalytic activity for MO and TC degradation under visible light. • The ZnFe2O4/Ag/Ag3VO4 photocatalyst is promising for designing an environmental purification material. - Abstract: A novel visible-light driven ZnFe{sub 2}O{sub 4}/Ag/Ag{sub 3}VO{sub 4} photocatalyst was successfully fabricated through a two-step hydrothermal method. The structure, morphology and composition of the samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and X-ray photo-electron spectroscopy (XPS). The as-prepared ZnFe{sub 2}O{sub 4}/Ag/Ag{sub 3}VO{sub 4} composites possessed an excellent performance in the photocatalytic degradation of methyl orange and tetracycline under visible-light irradiation. The results of electrochemical impedance spectroscopy (EIS) indicated that the ZnFe{sub 2}O{sub 4}/Ag/Ag{sub 3}VO{sub 4} composite could facilitate the separation of photo-generated carriers, as well as accelerated charge transfer. The 5% ZnFe{sub 2}O{sub 4}/Ag/Ag{sub 3}VO{sub 4} composite exhibited the upmost photocatalytic activity, the degradation constant of 5% ZnFe{sub 2}O{sub 4}/Ag/Ag{sub 3}VO{sub 4} is as high as 1.49 times to that of Ag/Ag{sub 3}VO{sub 4}. Also, according to the trapping experiments, it’s found that the superoxide radicals (·O{sub 2}{sup −}) and hole (h{sup +}) were the predominant reactive species in this system. The ZnFe{sub 2}O{sub 4}/Ag/Ag{sub 3}VO{sub 4} photocatalyst is promising for designing as an environmental purification material in treatment of antibiotic pollutant.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Application of GO anchored mediator in a polymer electrolyte membrane for high-rate solid-state supercapacitors

Here, we synthesized a novel polymer electrolyte membrane by combining poly (vinylidene fluoride) (PVDF) and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) with graphene oxide (GO) nanosheets and a lithium salt of tungstosilicic acid (Li 4 SiW 12 O 40 , hereafter, referred to SiWLi). The impact of the addition of GO/SiWLi on the microstructure and morphology of the membrane were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). We found that adding the GO/SiWLi to the PVDF/LiTFSI polymer electrolyte membrane significantly reduced the pore size. Furthermore, the addition of the GO/SiWLi resulted in not only an increase of the ionic conductivity from 0.87 $\times$ 10 –2 to 3.12 $\times$ 10 –2 Scm –1 but also an increase in the lithium-ion transference number from 0.52 to 0.87. The polymer electrolyte membranes with and without GO/SiWLi were utilized to fabricate solid-state supercapacitors. The supercapacitors fabricated with the membrane containing GO/SiWLi displayed 37.2% lower equivalent series resistance and 88.2% greater specific capacitance than those fabricated using the membrane without GO/SiWLi at 200mVs –1 .

42 ENGINEERING↗
DOE OSTI2016

NbTaV-(Ti,W) refractory high-entropy alloys: Experiments and modeling

This study reports the design and development of ductile and strong refractory single-phase high-entropy alloys (HEAs) for high temperature applications, based on NbTaV with addition of Ti and W. Assisted by CALPHAD modeling, a single body-centered cubic solid solution phase was experimentally confirmed in the as-cast ingots using X-ray diffraction and scanning electron microscopy. The observed elemental segregation in each alloy qualitatively agrees with CALPHAD prediction. The Vickers microhardnesses (and yielding strengths) of the alloys are about 3 (and 3.5-4.4) times that those estimated from the rule of mixture. While NbTaTiVW shows an impressive yielding strength of 1,420 MPa with fracture strain of 20%, NbTaTiV exhibits exceptional compressive ductility at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Corrosion of novel reactive silver ink and commercial silver-based metallizations in diluted acetic acid

Silver-based metallizations in photovoltaic modules are susceptible to corrosion by acetic acid generated in ethylene vinyl acetate encapsulated modules, resulting in power losses over time. Here, three silver-based metallizations are exposed to diluted acetic acid, in concentrations representative of that found in field-exposed modules. Compositional, morphological, and structural changes of the metallizations are studied over 3000 h of exposure to diluted acetic acid using Raman spectroscopy mapping, X-ray diffraction, and scanning electron microscopy. The three metallizations studied are: 1) a commercial high-temperature fire-through Ag paste, commonly used for Si diffused junction solar cells; 2) a commercial low-temperature paste normally used for silicon heterojunction cells; and 3) a novel low-temperature reactive silver ink shown to be suitable for photovoltaic applications. We find distinct corrosion rates for the high-temperature silver paste and reactive silver ink in the presence of diluted acetic acid. However, the low-temperature silver paste appears to be more corrosion resistant, likely due to a polymer layer that protects the silver particles.

36 MATERIALS SCIENCE↗
DOE OSTI2017

A Mössbauer spectral study of degradation in La 0.58 Sr 0.4 Fe 0.5 Co 0.5 O 3–x after long-term operation in solid oxide electrolysis cells

Here, degradation processes of oxygen electrodes in solid oxide electrolysis cells (SOECs) were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Mössbauer spectroscopy. La 0.58 Sr 0.4 Fe 0.5 Co 0.5 O 3–x (LSCF) anodes (oxygen electrode) were analyzed after different long-term operations durations of 1774, 6100 and 9000 h. The results were compared with a cell in the initial state. Besides the LSCF anode, the SOECs were composed of a Ce 0.8 Gd 0.2 O 1.9 barrier layer between the anode and electrolyte, yttria-stabilized zirconia (YSZ) as electrolyte and Ni-YSZ as cathode (hydrogen electrode). Mössbauer spectra of the iron-containing anode were acquired in order to determine the alteration of the iron oxidation state and its local environment during operation. Mössbauer spectroscopy yields indirect information about the degradation mechanism, especially in combination with SEM, TEM, and XRD. XRD and TEM revealed the appearance of Co 3 O 4 during the SOEC operation and SEM analyses confirmed the formation of SrZrO 3 at the electrode/electrolyte interface. The spectral analysis confirmed the reduction of iron from Fe(IV) to Fe(III) in LSCF after long-term operation. The fraction of Fe(IV) in the electrode decreased with time and 18, 15, 13 and 11% were obtained for 0, 1774, 6100, and 9000 h of operation, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

CMAS behavior of yttrium aluminum garnet (YAG) and yttria-stabilized zirconia (YSZ) thermal barrier coatings

Calcium magnesium aluminosilicate (CMAS) that is formed from the ingested deposits in gas turbines degrades thermal barrier coatings (TBCs), especially for the most widely used material; yttria-stabilized zirconia (YSZ). In the present work, we examine the behavior of yttrium aluminum garnet (YAG) as an alternative material for TBCs. CMAS interaction studies were conducted by making composite pellets of YAG-CMAS and YSZ-CMAS powders. These pellets, after being subjected to heat treatment between 1100 °C and 1500 °C were characterized by X-ray Diffraction (XRD), scanning electron microscopy (SEM) and Energy-dispersive X-ray spectroscopy (EDS), which showed YAG to be almost inert to CMAS whereas YSZ exhibited significant phase changes. To test the behavior of TBCs with YAG and 8YSZ as the topcoat material in a CMAS environment, cyclic furnace tests were conducted in which a controlled amount of CMAS was applied and then the samples were cycled to failure. In addition, to simulate the continuous accumulation of CMAS expected in service, a cyclic furnace test was devised in which a small dose of aqueous solution of CMAS was applied on TBC specimens at the start of every cycle until the samples were cycled to failure. In all these tests YAG TBCs outperformed YSZ in terms of durability. In conclusion, the mechanisms of CMAS attack are described and the relative resistance of YAG and YSZ is shown to be consistent with the Optical Basicity (OB) theory.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of oxygen on the optical and electrical properties of magnetron-sputtered indium tin oxide thin films at ambient temperature

Indium Tin Oxide (ITO) thin films are commonly used as transparent conductive layers in the production of solar cells. ITO films are typically heat-treated at temperatures exceeding 200 °C after magnetron sputtering to optimize the physical, optical, and electrical characteristics for photovoltaic devices. Here, this high temperature heating procedure greatly limits the use of potential substrates, particularly those comprised of low-temperature-rated polymers. Herein, we examine the physical, optical, and electrical transport effects of oxygen:argon plasmas during radio frequency magnetron sputtering of ITO on glass and flexible polymer surfaces without subsequent heat treatment. ITO thin films were characterized via sheet resistance testing, UV-Vis spectroscopy, X-ray diffraction, and scanning electron microscopy imaging. Sheet resistance measurements revealed an increase in surface resistance with increasing oxygen concentration during sputtering. UV-Vis optical transmittance measurements demonstrated an improvement in optical transmittance with an increase in oxygen concentration reaching a maximum transmittance at an oxygen concentration of 1-2 %. Most importantly, it was discovered that producing bilayers of ITO with pure argon sputtered plasmas followed by oxygen:argon plasmas produced ITO thin films with suitable resistance and transmittance without the need for high temperature post annealing. These results highlight a methodology for the deposition of ITO thin films on temperature sensitive substrates for flexible photovoltaics and low-cost module production.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Role of Ammonium Hydroxide on Glucose Oxidase Immobilized in Metal–Azolate Framework-7 Enzyme Activity

Enzymes are nature’s catalysts, but their instability outside native environments limits practical applications. Metal–organic frameworks (MOFs) offer a promising platform for enzyme immobilization, enhancing stability, and reusability through their tunable porosity and crystallinity. While ZIF-based MOFs have been extensively studied, metal azolate framework-7 (MAF-7) remains largely unexplored for biomimetic mineralization. Its hydrophilic character makes it a promising alternative for enzyme encapsulation; however, the role of essential basic modulators such as ammonium hydroxide (NH 4 OH) on enzyme structure and function has not been investigated. Here, in this study, we examine the NH 4 OH mediated synthesis of glucose oxidase within MAF-7 using powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), cryogenic transmission electron microscopy (cryo-TEM), and enzyme assays. Our results show that NH 4 OH modulates crystal morphology, enzyme activity, and nucleation behavior, with higher concentrations leading to partial enzyme denaturation and reduced catalytic performance. By integrating time-resolved cryo-TEM with activity assays, we uncover how modulator concentration impacts early stage crystallization and enzyme folding, a mechanistic insight not previously demonstrated in MOF systems. These findings highlight modulator chemistry as a critical, underexplored variable in MOF synthesis, advancing rational design strategies for enzyme@MOFs (E@MOF) beyond ZIFs and toward more tunable, biocompatible frameworks like MAF-7.

36 MATERIALS SCIENCE↗
DOE OSTI2016

First 14-Layer Twinned Hexagonal Perovskite Ba 14 Mn 1.75 Ta 10.5 O 42 : Atomic-Scale Imaging of Cation Ordering

Formation of hexagonal perovskite with mixed cubic and hexagonal stacking of AO 3 layers becomes more and more difficult when the number of layers in the stacking repeating unit increases. So far, the highest number of layers reported for twinned hexagonal perovskite is 12, with alternative 5 consecutive cubic layers and one hexagonal layer in the (ccccch) 2 sequence. Here, we present the unexpected formation of a 14-layer twinned hexagonal perovskite with a stacking sequence (cccccch) 2 for the BaO 3 layers on the Ba 14 Mn 1.75 Ta 10.5 O 42 (Ba 8 MnTa 6 O 24 ) composition, the first example of twinned hexagonal perovskite with a periodicity exceeding 12-layers. The B-cation and vacancy distributions are characterized by multiple efficient and complementary techniques including neutron and synchrotron powder diffraction, scanning transmission electron microscopy-high angle annular dark field (STEM-HAADF) imaging, and electron energy loss spectroscopy (EELS) and X-ray energy dispersive spectroscopy (EDS) elemental mapping. Atomic-resolution STEM-HAADF imaging and EELS/EDS elemental mapping enables direct observation of high-spin d 5 Mn 2+ cation ordering in the d 0 Ta 5+ host, thus demonstrating the great potential of this technique for probing cation ordering and performing structure determination. Moreover, atomic mapping allows for the observation of local defect structure variants, which can be a powerful tool for future new material design. The large high-spin Mn 2+ cation and Ta-vacancy pair formation in face-sharing octahedral sites play key roles on both the stabilization of this 14-layer twinned hexagonal perovskite structure and the Mn 2+ ordering in the central corner-sharing octahedral (CSO) positions within the five-consecutive CSO layers. Here, compared with the 8-layer twinned Ba 8 ZnTa 6 O 24 material, the low quality factor in microwave frequency and enhanced ultraviolet and visible light absorption of Ba 14 Mn 1.75 Ta 10.5 O 42 as well as the photocatalytic activity on water splitting are discussed in terms of the presence of high-spin Mn 2+ cations in the structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Crystallization and Phase Transformations of Aluminum (Oxy)hydroxide Polymorphs in Caustic Aqueous Solution

Gibbsite, bayerite, and boehmite are important aluminum (oxy)hydroxide minerals in nature and have been widely deployed in various industrial applications. They are also major components in caustic nuclear wastes stored at various U.S. locations. Knowledge of their crystallization and phase transformation processes contributes to understanding their occurrence and could help optimize waste treatment processes. While it has been reported that partial conversion of bayerite and gibbsite to boehmite occurs in basic solutions at elevated temperatures, systematic studies of factors affecting the phase transformation as well as the underlying reaction mechanisms are non-existent, particularly in highly alkaline solutions. We explored the effects of sodium hydroxide concentrations (0.1~3 M), reaction temperature (60~100 ?) and aluminum concentrations (0.1~1 M) on the crystallization and transformation of these aluminum (oxy)hydroxides. Detailed structural and morphological characterization by X-ray diffraction (XRD), scanning electron microscopy (SEM), and nuclear magnetic resonance (NMR) spectrometry revealed that these processes depend largely on the reaction temperature and the Al/OH- ratio. When 1 = Al/OH- = 2.5, the reactions favor formation of high crystallinity precipitates, whereas at Al/OH- ratio ? 2.5 precipitation ceases unless the Al concentration is higher than 1 M. We identified pseudoboehmite, bayerite and gibbsite as intermediate phases to bayerite, gibbsite and boehmite, respectively, all of which transform via dissolution-reprecipitation. Gibbsite transforms to boehmite in both acidic and weak caustic environments at temperatures above 80 oC. However, a ‘bar-shaped’ gibbsite morphology dominates in highly caustic environments (3 M NaOH). The findings enable a robust basis for selection of various solid phases by tuning the reaction conditions.

aluminum (oxy)hydroxide polymorphs, crystallizatio↗
DOE OSTI2018

Single-Doped and Multidoped Transition-Metal (Mn, Fe, Co, and Ni) ZnO and Their Electrocatalytic Activities for Oxygen Reduction Reaction

The electrochemical oxygen reduction reaction (ORR) is the limiting half-reaction of fuel cells, which is mediated by using platinum-based catalysts. Hence, the development of low-cost, active ORR catalysts is highly required to make fuel cell technology commercially available. In this report, transition-metal (TM; Mn, Fe, Co, and Ni) single-doped and multidoped (MD) ZnO nanocrystals (ZNs) were prepared for use as ORR catalysts using a simple precipitation method. The effects of single doping and multidoping on the structure, morphology, and properties of the TM-doped ZNs were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray fluorescence, X-ray photoelectron microscopy, electron paramagnetic resonance, and Raman and photoluminescence (PL) spectroscopies. The XRD results reveal that synthesized ZnO samples retained a pure hexagonal wurtzite crystal structure, even at high levels of multidoping (nominal 20%). SEM analyses show that the morphology of the prepared ZNs varies with the doping elements, doping mode, and amounts of doping. The observation of peak shifting and peak intensity changes in Raman studies confirms the presence of dopants in ZnO. The PL investigation reveals that the incorporation of dopants into the ZnO structure increases the oxygen vacancies within the materials. The highest oxygen vacancies were present in Mn-doped ZnO and 15% MD ZnO among the single-doped and MD samples, respectively. Linear-sweep voltammetry studies conclude that doped ZnO shows enhanced ORR activity compared to the undoped samples. The Mn-doped ZnO and 15% MD ZnO exhibited the highest ORR activity among the prepared single-doped and MD ZN samples, respectively. In comparison, single doping showed better ORR activity than the multidoping system. The enhanced ORR activity of the synthesized ZN materials correlates with the amount of oxygen vacancies present in the samples. Finally, the enhanced activity of TM-doped ZnO suggests that these materials can be used as potential, low-cost electrocatalysts for ORR in fuel cell technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Unraveling Gibbsite Transformation Pathways into LiAl-LDH in Concentrated Lithium Hydroxide

The intercalation of lithium (Li+) ions into metallic hydroxides (e.g. gibbsite, Al(OH)3) facilitates the synthesis of layered double hydroxides. Caustic environments, such as in lithium hydroxide (LiOH) solutions, present additional pathways beyond the intercalation of ions, specifically dissolution/precipitation processes. Herein, the phase transformation Al(OH)3 to lithium aluminum hydroxide dihydrate, Li[Al(OH)3)]2OH•2H2O in partially deuterated LiOH solutions is tracked through multinuclear, magic angle spinning, high-field nuclear magnetic resonance spectroscopy (27Al and 6Li MAS-NMR) , X-ray diffraction, and scanning electron microscopy of harvested solids. At high magnetic fields (19.975 T), 27Al MAS-NMR enabled detection and quantification of the reactive interface between Al(OH)3 and Li[Al(OH)3)]2OH•2H2O. 6Li MAS-NMR spectra collected on the harvested solids exhibited exchange mediated narrowing as the reaction time progressed, consistent with transport of Li+ ions between the interface and the bulk Li[Al(OH)3)]2OH•2H2O. Complimentary in-situ 27Al MAS-NMR at lower magnetic fields (7.046 T) utilized unique rotors capable of simultaneous resolution of solution and solid state Al-species in caustic environments. The reaction between Al(OH)3 (0.5 M) and LiOH (3 M) initially exhibited greater dissolution and formation of Al(OH)4- than the precipitation. Over several hours, the supersaturated Al(OH)4- solution precipitated Li[Al(OH)3)]2OH•2H2O. Simultaneous, in-situ observations of the solid component tracked the formation of Li[Al(OH)3)]2OH•2H2O evident by an increase in signal and narrowing of the Oh resonance. These results provides insight into Al precipitation in alkaline media with applications ranging from the reduction of Al content in Hanford site, high-level radioactive waste (HLRW) to the precipitation of LDH materials for application as catalyst materials, drug delivery devices, and ion-ion exchangers.

Graham, Trenton R.↗
DOE OSTI2017

Atomic Structure of Submonolayer NaCl Grown on Ag(110) Surface

In this work, we report results on the growth of an NaCl film on Ag(110) under ultrahigh vacuum conditions. At room temperature, low-energy electron diffraction and scanning tunneling microscopy show that the NaCl film forms a (4×1) superstructure. At RT, the film consists of small-sized islands that coalesce into larger islands at 410 K. These large islands preserve the (4×1) superstructure and cover the entire surface. The apparent heights obtained from the STM images show that the initial thickness of the NaCl islands is one atomic layer, and they present a very small height corrugation. The density functional theory calculations, with and without the inclusion of van der Waals effects, confirm the coexistence of two domains in agreement with the observed structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Gaseous Iodine Sorbents: A Comparison between Ag-Loaded Aerogel and Xerogel Scaffolds

The general properties of aluminosilicate aerogels and xerogels with silver nanoparticles as sorbents for capturing iodine gas [I2(g)] were investigated. The structures, morphologies, compositions, and pore structures of aerogel and xerogel were compared using powder X-ray diffraction (PXRD), scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, as well as specific surface area (SSA) and pore size analyses. The as-made aerogels, xerogels, and heat-treated aerogels were impregnated with Ag by aqueous ion exchange using AgNO3 solutions, and PXRD patterns showed the presence of nanocrystalline Ag0 after Ag-impregnation. Iodine loadings of aerogels and xerogels were 0.33–0.41 g g-1. The Ag-impregnated aerogels without heat-treatment showed an 8 mass% higher iodine loading than Ag-impregnated xerogels and 3 mass% higher than heat-treated Ag-impregnated aerogels. All gels after iodine uptake showed the presence of AgI, indicating chemisorption of iodine to silver. The SSA values of the as-made gels were 419–598 m2 g-1 but decreased significantly to 34–120 m2 g-1 after Ag-impregnation and iodine uptake processes. Overall, changes in physical and chemical properties of aerogels and xerogels after iodine uptake were similar, and the difference in iodine loading capacities of the aerogels and xerogels was not significant while the synthesis process of xerogel is more practical because it does not require supercritical drying.

aerogel, xerogel, iodine capture↗