SEARCH · Search NASA

Results for “segmental dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Passive Stabilization of Rotating Tethered Spacecraft

Rotating Spacecrafts can provide artificial gravity for long-term space missions, but the design of a Guidance and Control scheme for these vehicles is nuanced. For a three-segment vehicle with the propulsion element located at the center of mass, the vehicle must stabilize itself about this point even in the event of various off-nominal circumstances. Thus, a robust and passive spin stabilization system is needed. In this paper, various methods for stabilizing the system to allow for the exchange of mass and air between elements are explored and simulated.

Dynamics↗

NASA NTRS2011

UAS Modeling of the Communication Links Study Results

The Federal Aviation Administration (FAA) is the authority that grants access into, and operations within, the National Airspace System (NAS) for all aircraft, including Unmanned Aircraft Systems (UAS). The safe operation of UAS in the NAS must be assured if the full potential of UAS is to be realized and supported by the public and Congress. This report analyzed the communication systems that are needed for the safe operations of UAS in the NAS. Safe operations can be defined as the availability of the required links to carry the information to control the UAS and the return links to allow controllers to know where the UAS is at any given moment as well as how it is performing. This report is the end result of work performed jointly between the FAA and National Aeronautics and Space Administration (NASA)/Kennedy Space Center (NASA KSC). The work was done in support of the Radio Technical Commission for Aeronautics (RTCA) Special Committee 203 (SC-203) Control and Communications Working Group. The RTCA is a federal advisory committee to the FAA. Though the work was not under the direction of the working group, a large part of the specific values used in the simulations came from the working group. Specifically, all of the radio links were modeled based on the formulation completed by the working group. This report analyzed three scenarios from RTCA SC-203 that represent how a UAS would operate in the NAS. Each scenario was created using the Satellite Tool Kit (STK) modeling and simulation tool. The flight paths of the UAS were generated and the UAS dynamics were likewise modeled. Then each communication asset such as transmitters, receivers, and antennas were modeled and placed on the appropriate UAS, satellite, or Control Station (CS). After that, the radio links were analyzed for signal strength and antenna blockage, and the overall link performance was analyzed in detail. The goal was to obtain 99.9% availability on all of the radio communication links. In order to ensure the 99.9% availability, certain values for the telemetry transmitter will have to be increased slightly from I watt up to about 4 watts which is reasonable. The results of this analysis show that it is possible to send commands, during the airborne segment, to the Unmanned Aircraft (UA) and have the UA send back the system health and status with high availability of at least 99.9% of the time. This 99.9% availability included the condition of heavy rain at 90 mm/hr as well as interference from adjacent satellites. The link budget values used in this report were based on the work from the working group.

Birr, Richard B.↗

NASA NTRS2000

Horizon: A Proposal for Large Aperture, Active Optics in Geosynchronous Orbit

In 1999, NASA's New Millennium Program called for proposals to validate new technology in high-earth orbit for the Earth Observing-3 (NMP EO3) mission to fly in 2003. In response, we proposed to test a large aperture, active optics telescope in geosynchronous orbit. This would flight-qualify new technologies for both Earth and Space science: 1) a future instrument with LANDSAT image resolution and radiometric quality watching continuously from geosynchronous station, and 2) the Next Generation Space Telescope (NGST) for deep space imaging. Six enabling technologies were to be flight-qualified: 1) a 3-meter, lightweight segmented primary mirror, 2) mirror actuators and mechanisms, 3) a deformable mirror, 4) coarse phasing techniques, 5) phase retrieval for wavefront control during stellar viewing, and 6) phase diversity for wavefront control during Earth viewing. Three enhancing technologies were to be flight- validated: 1) mirror deployment and latching mechanisms, 2) an advanced microcontroller, and 3) GPS at GEO. In particular, two wavefront sensing algorithms, phase retrieval by JPL and phase diversity by ERIM International, were to sense optical system alignment and focus errors, and to correct them using high-precision mirror mechanisms. Active corrections based on Earth scenes are challenging because phase diversity images must be collected from extended, dynamically changing scenes. In addition, an Earth-facing telescope in GEO orbit is subject to a powerful diurnal thermal and radiometric cycle not experienced by deep-space astronomy. The Horizon proposal was a bare-bones design for a lightweight large-aperture, active optical system that is a practical blend of science requirements, emerging technologies, budget constraints, launch vehicle considerations, orbital mechanics, optical hardware, phase-determination algorithms, communication strategy, computational burdens, and first-rate cooperation among earth and space scientists, engineers and managers. This manuscript presents excerpts from the Horizon proposal's sections that describe the Earth science requirements, the structural -thermal-optical design, the wavefront sensing and control, and the on-orbit validation.

Chesters, Dennis↗

NASA NTRS2016

Persistence Mapping Using EUV Solar Imager Data

We describe a simple image processing technique that is useful for the visualization and depiction of gradually evolving or intermittent structures in solar physics extreme-ultraviolet imagery. The technique is an application of image segmentation, which we call "Persistence Mapping," to isolate extreme values in a data set, and is particularly useful for the problem of capturing phenomena that are evolving in both space and time. While integration or "time-lapse" imaging uses the full sample (of size N ), Persistence Mapping rejects (N - 1)/N of the data set and identifies the most relevant 1/N values using the following rule: if a pixel reaches an extreme value, it retains that value until that value is exceeded. The simplest examples isolate minima and maxima, but any quantile or statistic can be used. This paper demonstrates how the technique has been used to extract the dynamics in long-term evolution of comet tails, erupting material, and EUV dimming regions.

Thompson, B. J.↗

NASA NTRSDate not supplied

Expanding NeMO-Net Machine Learning Capabilities for Citizen Science

NASA NeMO-Net, the neural multi-modal observation and training network for global coral reef assessment, is an open-source deep convolutional neural network and interactive active learning training software aiming to accurately assess the present and past dynamics of coral reef ecosystems through determination of percent living cover and morphology as well as mapping of spatial distribution. We present an interactive citizen science video game, released this April, for desktop and iOS devices where users interactively label morphology classifications over mm-scale 3D coral reef imagery captured using diver photomosaic imagery, the UAV enabled NASA FluidCam instrument, and satellite datasets. To date, the application has had over 40,000 downloads and over60,000 unique coral reef classifications, each filtered through a user-based rating and expert evaluation system. We also present results from NeMO-Net’s convolutional neural network (CNN) models used to semantically segment 2D satellite imagery as well as projections of 3D coral reconstructions using user input data as training datasets. Fusing datasets using machine learning from multiple remote sensing platforms presents novel methodologies for assessing the health of coral ecosystems, which are critically endangered by a changing climate. In partnering with Mission Blue, the National Oceanic and Atmospheric Administration (NOAA), and the Living Oceans Foundation (LOF), NeMO-Net leverages an international consortium of subject matter experts to provide both proper training for citizen scientists and the generation of a labeled datasets to ingest into machine learning algorithms for global coral reef identification.

NeMO-Net↗

NASA NTRSDate not supplied

Expanding NeMO-Net Machine Learning Capabilities for Citizen Science

NASA NeMO-Net, the neural multi-modal observation and training network for global coral reef assessment, is an open-source deep convolutional neural network and interactive active learning training software aiming to accurately assess the present and past dynamics of coral reef ecosystems through determination of percent living cover and morphology as well as mapping of spatial distribution. We present an interactive citizen science video game, released this April, for desktop and iOS devices where users interactively label morphology classifications over mm-scale 3D coral reef imagery captured using diver photomosaic imagery, the UAV enabled NASA FluidCam instrument, and satellite datasets. To date, the application has had over 40,000 downloads and over 60,000 unique coral reef classifications, each filtered through a user-based rating and expert evaluation system. We also present results from NeMO-Net’s convolutional neural network (CNN) models used to semantically segment 2D satellite imagery as well as projections of 3D coral reconstructions using user input data as training datasets. Fusing datasets using machine learning from multiple remote sensing platforms presents novel methodologies for assessing the health of coral ecosystems, which are critically endangered by a changing climate. In partnering with Mission Blue, the National Oceanic and Atmospheric Administration (NOAA), and the Living Oceans Foundation (LOF), NeMO-Net leverages an international consortium of subject matter experts to provide both proper training for citizen scientists and the generation of a labeled datasets to ingest into machine learning algorithms for global coral reef identification.

NeMO-Net↗

NASA NTRS1996

RSRM Chamber Pressure Oscillations: Transit Time Models and Unsteady CFD

Space Shuttle solid rocket motor low frequency internal pressure oscillations have been observed since early testing. The same type of oscillations also are present in the redesigned solid rocket motor (RSRM). The oscillations, which occur during RSRM burn, are predominantly at the first three motor cavity longitudinal acoustic mode frequencies. Broadband flow and combustion noise provide the energy to excite these modes at low levels throughout motor burn, however, at certain times during burn the fluctuating pressure amplitude increases significantly. The increased fluctuations at these times suggests an additional excitation mechanism. The RSRM has inhibitors on the propellant forward facing surface of each motor segment. The inhibitors are in a slot at the segment field joints to prevent burning at that surface. The aft facing segment surface at a field joint slot burns and forms a cavity of time varying size. Initially the inhibitor is recessed in the field joint cavity. As propellant burns away the inhibitor begins to protrude into the bore flow. Two mechanisms (transit time models) that are considered potential pressure oscillation excitations are cavity-edge tones, and inhibitor hole-tones. Estimates of frequency variation with time of longitudinal acoustic modes, cavity edge-tones, and hole-tones compare favorably with frequencies measured during motor hot firing. It is believed that the highest oscillation amplitudes occur when vortex shedding frequencies coincide with motor longitudinal acoustic modes. A time accurate computational fluid dynamic (CFD) analysis was made to replicate the observations from motor firings and to observe the transit time mechanisms in detail. FDNS is the flow solver used to detail the time varying aspects of the flow. The fluid is approximated as a single-phase ideal gas. The CFD model was an axisymmetric representation of the RSRM at 80 seconds into burn.Deformation of the inhibitors by the internal flow was determined through an iterative structural and CFD analysis. The analysis domain ended just upstream of the nozzle throat. This is an acoustic boundary condition that caused the motor to behave as a closed-open organ pipe. This differs from the RSRM which behaves like a closed-closed organ pipe. The unsteady CFD solution shows RSRM chamber pressure oscillations predominately at the longitudinal acoustic mode frequencies of a closed-open organ pipe. Vortex shedding in the joint cavities and at the inhibitors contribute disturbances to the flow at the second longitudinal acoustic mode frequency. Further studies are planned using an analysis domain that extends downstream of the nozzle throat.

Nesman, Tom↗

NASA NTRS2011

Ares I-X Test Flight Reference Trajectory Development

Ares I-X was the first test flight of NASA's Constellation Program's Ares I crew launch vehicle. Ares I is a two stage to orbit launch vehicle that provides crew access to low Earth orbit for NASA's future manned exploration missions. The Ares I first stage consists of a Shuttle solid rocket motor (SRM) modified to include an additional propellant segment and a liquid propellant upper stage with an Apollo J2X engine modified to increase its thrust capability. The modified propulsion systems were not available for the first test flight, thus the test had to be conducted with an existing Shuttle 4 segment reusable solid rocket motor (RSRM) and an inert Upper Stage. The test flight's primary objective was to demonstrate controllability of an Ares I vehicle during first stage boost and the ability to perform a successful separation. In order to demonstrate controllability, the Ares I-X ascent control algorithms had to maintain stable flight throughout a flight environment equivalent to Ares I. The goal of the test flight reference trajectory development was to design a boost trajectory using the existing RSRM that results in a flight environment equivalent to Ares I. A trajectory similarity metric was defined as the integrated difference between the Ares I and Ares I-X Mach versus dynamic pressure relationships. Optimization analyses were performed that minimized the metric by adjusting the inert upper stage weight and the ascent steering profile. The sensitivity of the optimal upper stage weight and steering profile to launch month was also investigated. A response surface approach was used to verify the optimization results. The analyses successfully defined monthly ascent trajectories that matched the Ares I reference trajectory dynamic pressure versus Mach number relationship to within 10% through Mach 3.5. The upper stage weight required to achieve the match was found to be feasible and varied less than 5% throughout the year. The paper will discuss the flight test requirements, provide Ares I-X vehicle background, discuss the optimization analyses used to meet the requirements, present analysis results, and compare the reference trajectory to the reconstructed flight trajectory.

Starr, Brett R.↗

NASA NTRS2011

Planetary Suit Hip Bearing Model for Predicting Design vs. Performance

Designing a planetary suit is very complex and often requires difficult trade-offs between performance, cost, mass, and system complexity. In order to verifying that new suit designs meet requirements, full prototypes must eventually be built and tested with human subjects. Using computer models early in the design phase of new hardware development can be advantageous, allowing virtual prototyping to take place. Having easily modifiable models of the suit hard sections may reduce the time it takes to make changes to the hardware designs and then to understand their impact on suit and human performance. A virtual design environment gives designers the ability to think outside the box and exhaust design possibilities before building and testing physical prototypes with human subjects. Reductions in prototyping and testing may eventually reduce development costs. This study is an attempt to develop computer models of the hard components of the suit with known physical characteristics, supplemented with human subject performance data. Objectives: The primary objective was to develop an articulating solid model of the Mark III hip bearings to be used for evaluating suit design performance of the hip joint. Methods: Solid models of a planetary prototype (Mark III) suit s hip bearings and brief section were reverse-engineered from the prototype. The performance of the models was then compared by evaluating the mobility performance differences between the nominal hardware configuration and hardware modifications. This was accomplished by gathering data from specific suited tasks. Subjects performed maximum flexion and abduction tasks while in a nominal suit bearing configuration and in three off-nominal configurations. Performance data for the hip were recorded using state-of-the-art motion capture technology. Results: The results demonstrate that solid models of planetary suit hard segments for use as a performance design tool is feasible. From a general trend perspective, the suited performance trends were comparable between the model and the suited subjects. With the three off-nominal bearing configurations compared to the nominal bearing configurations, human subjects showed decreases in hip flexion of 64%, 6%, and 13% and in hip abduction of 59%, 2%, and 20%. Likewise the solid model showed decreases in hip flexion of 58%, 1%, and 25% and in hip abduction of 56%, 0%, and 30%, under the same condition changes from the nominal configuration. Differences seen between the model predictions and the human subject performance data could be attributed to the model lacking dynamic elements and performing kinematic analysis only, the level of fit of the subjects with the suit, the levels of the subject s suit experience.

Cowley, Matthew S.↗

NASA NTRS1991

Macromolecular recognition: Structural aspects of the origin of the genetic system

Theoretical simulation of prebiotic chemical processes is an invaluable tool for probing the phenomenon of evolution of life. Using computational and modeling techniques and guided by analogies from present day systems we, seek to understand the emergence of genetic apparatus, enzymatic catalysis and protein synthesis under prebiotic conditions. In one possible scenario, the RNA enzymatic reaction plays a key role in the emergence of the self-replicating and offers a clue to the onset of enzymatic catalysis prior to the existence of the protein biosynthetic machinery. Our ultimate goal is to propose a simple RNA segment which contains the specificity and catalytic activity of the contemporary RNA enzyme and which could emerge in a primordial chemical environment. To understand the mechanism of ribozyme catalyzed reactions, ab initio and semi-empirical (ZINDO) programs were used to investigate the reaction path of transphosphorylation. A special emphasis was placed on the possible catalytic and structural roles played by the coordinated magnesium cation. Both the inline and adjacent mechanisms of transphosphorylation have been studied. Another important aspect of this reaction is the identity of the functional groups which are essential for the acid base catalysis. The structural characteristics of the target helices, particularly a possible role of G center dot T pair, is under examination by molecular dynamics (MD) simulation technique. Modeling of the ancestral aminoacyl-tRNA synthetases (aRS) may provide important clues to the emergence of the genetic code and the protein synthetic machinery. Assuming that the catalytic function evolved before the elements of specific recognition of a particular amino acid, we are exploring the minimal structural requirements for the catalysis of tRNA aminoacylation. The molecular modeling system SYBYL was used for this study based on the high resolution crystallographic structures of the present day tyrosyl-adenylate:tyrRS and tRNA(Gln): ATP:glnRS complexes. The trinucleotide CCA of the 3'-end tRNA is placed into the active site pocket of tyrRS, based on the scheme of interaction between tRNA(Gln) and glnRS, and upon the stereochemistry of the tyrRS:tRNA:Tyr-AMP transition state. This provides a model of the non-specific recognition of a tRNA's 3'-end by an aRS, which might be similar to that of the ancestral aRS's. In the next step, modeling of the rest of the acceptor stem of tRNA (Tyr) with tyrRS is carried out.

Rein, Robert↗

NASA NTRSDate not supplied

Modeling Autogenous Pressurization and Draining of a Cryogenic Storage Tank in Normal Gravity

A two-phase CFD model for autogenous pressurization and draining of a cryogenic storage tank is presented using both the Sharp Interface and Volume-Of-Fluid (VOF) approaches for capturing the front and the associated interfacial heat, mass and momentum transfer between the liquid and vapor regions. Both models are validated against data provided by the Cryogenic Propellant Storage and Transfer (CPST) Engineering Development Unit (EDU) experiment. The results of the autogenous pressurization are presented first, focusing on the phase change and turbulence effects on the tank pressure and temperature predictions. Both the Sharp Interface (SI-CFD) and VOF (VOF-CFD) multiphase models predict tank pressure during pressurization within 3% of the measured values. The sensitivity of key physical and numerical parameters of the problem are tested using the Sharp Interface model. Effects of the accommodation coefficient (AC), and the computational grid structure are studied. The second part of this paper is devoted to validating the SI-VOF model, with an enhanced capability of moving the liquid-vapor interface, against the draining segment of the EDU experiment. The VOF-CFD model was also used to simulate tank draining and its results were compared with the results of the Sharp Interface model with the moving interface. Both models predict tank pressure during draining within 3.5% of the measured values. Pressure decrease rate is underpredicted by both models during the first 100 seconds of draining but matches the experimental rate for the rest of the simulation.

Computational Fluid Dynamics↗

NASA NTRSDate not supplied

Modeling Autogenous Pressurization and Draining of a Cryogenic Storage Tank in Normal Gravity

A two-phase CFD model for autogenous pressurization and draining of a cryogenic storage tank is presented using both the Sharp Interface and Volume-Of-Fluid (VOF) approaches for capturing the front and the associated interfacial heat, mass and momentum transfer between the liquid and vapor regions. Both models are validated against data provided by the Cryogenic Propellant Storage and Transfer (CPST) Engineering Development Unit (EDU) experiment1. The results of the autogenous pressurization are presented first, focusing on the phase change and turbulence effects on the tank pressure and temperature predictions. Both the Sharp Interface (SI-CFD) and VOF (VOF-CFD) multiphase models predict tank pressure during pressurization within 3% of the measured values. The sensitivity of key physical and numerical parameters of the problem are tested using the Sharp Interface model. Effects of the accommodation coefficient (AC), and the computational grid structure are studied. The second part of this paper is devoted to validating the SI-VOF model, with an enhanced capability of moving the liquid-vapor interface, against the draining segment of the EDU experiment. The VOF-CFD model was also used to simulate tank draining and its results were compared with the results of the Sharp Interface model with the moving interface. Both models predict tank pressure during draining within 3.5% of the measured values. Pressure decrease rate is underpredicted by both models during the first 100 seconds of draining but matches the experimental rate for the rest of the simulation.

Computational Fluid Dynamics↗

NASA NTRS1998

On the Generation and Use of TCP Acknowledgments

This paper presents a simulation study of various TCP acknowledgment generation and utilization techniques. We investigate the standard version of TCP and the two standard acknowledgment strategies employed by receivers: those that acknowledge each incoming segment and those that implement delayed acknowledgments. We show the delayed acknowledgment mechanism hurts TCP performance, especially during slow start. Next we examine three alternate mechanisms for generating and using acknowledgments designed to mitigate the negative impact of delayed acknowledgments. The first method is to generate delayed ACKs only when the sender is not using the slow start algorithm. The second mechanism, called byte counting, allows TCP senders to increase the amount of data being injected into the network based on the amount of data acknowledged rather than on the number of acknowledgments received. The last mechanism is a limited form of byte counting. Each of these mechanisms is evaluated in a simulated network with no competing traffic, as well as a dynamic environment with a varying amount of competing traffic. We study the costs and benefits of the alternate mechanisms when compared to the standard algorithm with delayed ACKs.

Allman, Mark↗

NASA NTRS2010

Modeling Flight: The Role of Dynamically Scaled Free-Flight Models in Support of NASA's Aerospace Programs

The state of the art in aeronautical engineering has been continually accelerated by the development of advanced analysis and design tools. Used in the early design stages for aircraft and spacecraft, these methods have provided a fundamental understanding of physical phenomena and enabled designers to predict and analyze critical characteristics of new vehicles, including the capability to control or modify unsatisfactory behavior. For example, the relatively recent emergence and routine use of extremely powerful digital computer hardware and software has had a major impact on design capabilities and procedures. Sophisticated new airflow measurement and visualization systems permit the analyst to conduct micro- and macro-studies of properties within flow fields on and off the surfaces of models in advanced wind tunnels. Trade studies of the most efficient geometrical shapes for aircraft can be conducted with blazing speed within a broad scope of integrated technical disciplines, and the use of sophisticated piloted simulators in the vehicle development process permits the most important segment of operations the human pilot to make early assessments of the acceptability of the vehicle for its intended mission. Knowledgeable applications of these tools of the trade dramatically reduce risk and redesign, and increase the marketability and safety of new aerospace vehicles. Arguably, one of the more viable and valuable design tools since the advent of flight has been testing of subscale models. As used herein, the term "model" refers to a physical article used in experimental analyses of a larger full-scale vehicle. The reader is probably aware that many other forms of mathematical and computer-based models are also used in aerospace design; however, such topics are beyond the intended scope of this document. Model aircraft have always been a source of fascination, inspiration, and recreation for humans since the earliest days of flight. Within the scientific community, Leonardo da Vinci, George Cayley, and the Wright brothers are examples of early aviation pioneers who frequently used models during their scientific efforts to understand and develop flying machines. Progress in the technology associated with model testing in worldwide applications has firmly established model aircraft as a key element in new aerospace research and development programs. Models are now routinely used in many applications and roles, including aerodynamic data gathering in wind tunnel investigations for the analysis of full-scale aircraft designs, proof-of-concept demonstrators for radical aeronautical concepts, and problem-solving exercises for vehicles already in production. The most critical contributions of aerospace models are to provide confidence and risk reduction for new designs and to enhance the safety and efficiency of existing configurations.

Chambers, Joseph↗

NASA NTRSDate not supplied

Segmented Hexagonal Antenna Reflector Concentrically Stacked Using Shape Memory Composite Tubular Hinges

A new architecture for solid surface reflector antennas scalable to sizes greater than 10 m is presented. The design combines the compact, lightness and simplicity characteristics of advanced deployable structures to create sub-reflectors that can be assembled in space into larger units using a robotic arm and operations under development by a related parallel project. The seven-panel hexagonal sub-reflector is divided into hexagonal panels of that efficiently stack concentrically and vertically. The central panel is connected to each side panel on the back side by a pair of tubular shape memory composite hinges that enable the required deployment kinematics. A secondary mechanism ultimately closes the interpanel gap. The focus of the paper is on the development of the sub-reflector elements, namely the tubular hinges that use embedded heaters and sensors for actuation, the actuation mechanisms, and the lightweight sandwich construction panels. A finite element analysis parametric study assessed how design features of the hinge affect its stowage and deployment dynamics. The component fabrication and testing plans for the two-panel assembly breadboard model are outlined.

deployable reflectors↗

NASA NTRSDate not supplied

Segmented Hexagonal Antenna Reflector Concentrically Stacked Using Shape Memory Composite Tubular Hinges

deployable reflectors↗

NASA NTRS1996

Pressure Oscillations in Shuttle Solid Rocket Motors

All Shuttle Solid Rocket Motors (SRM's) exhibit low amplitude longitudinal pressure oscillations during motor burn. Although the oscillations have no known deleterious effect on motor ballistics, the acoustic pressure variations cause thrust oscillations that might affect Shuttle systems or components. The acoustic mode of greatest interest is the first or fundamental mode which, in the SRM, has a nominal frequency of 14-Hz. Oscillations in the SRM are believed to be caused by coupling between large scale vortices and the acoustic modes of the motor chamber. The vortices are thought to be created in the region of the motor segment interfaces and are inherent in the design of the motor. In such a situation the usual approach is to measure the oscillations and assess their impact on any sensitive components through tests and analysis. Questionable components can be altered to survive the vibration environment. As motor firings occur, oscillations are monitored to determine whether there are changes in the nature of the oscillations. Since the first static test, SRM's have been equipped with instrumentation especially designed to acquire chamber pressure oscillation data. Data from the first SRM static tests were used to establish predicted upper bounds for the maximum amplitudes in the latter half of burn. Those bounds have been used as a basis for worst-case simulation scenarios by specialists in structural dynamics at NASA and Rockwell International and to provide a basis for evaluating data from individual motors which were tested subsequent to the original SRM's. This paper updates the upper bounds prediction the High Performance Motors (HPM) by including data from all static tests performed to date including both original SRM's and post Challenger SRM's or Reusable Solid Rocket Motors (RSRM) in which the joint design was changed. All together, this study examines 27 SRM motors, 16 HPM motors and 11 RSRM motors. Predicted upper bounds will be made for both the first and second longitudinal modes. The first mode upper bounds will be compared to the original seven standard rocket motors (STD). The results indicate that, although the upper bounds have increased, they are still within acceptable bounds.

Blomshield, Fred S.↗

NASA NTRS1980

Steady state solutions to dynamically loaded periodic structures

The general problem of solving for the steady state (time domain) dynamic response (i.e., NASTRAN rigid format-8) of a general elastic periodic structure subject to a phase difference loading of the type encountered in traveling wave propagation problems was studied. Two types of structural configurations were considered; in the first type, the structure has a repeating pattern over a span that is long enough to be considered, for all practical purposes, as infinite; in the second type, the structure has structural rotational symmetry in the circumferential direction. The theory and a corresponding set of DMAP instructions which permits the NASTRAN user to automatically alter the rigid format-8 sequence to solve the intended class of problems are presented. Final results are recovered as with any ordinary rigid format-8 solution, except that the results are only printed for the typical periodic segment of the structure. A simple demonstration problem having a known exact solution is used to illustrate the implementation of the procedure.

Kalinowski, A. J.↗