Search NASA⌕ Search

SEARCH · Search NASA

Results for “strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Force-Strain Characteristics and Rupture-Load Capability of Viking-Type Suspension-Line Material Under Dynamic Loading Conditions

A series of tests has been conducted to investigate the elastic behavior of Viking-type suspension-line material under dynamic loading conditions. Results indicate that there is a decrease in both rupture-load capability and elongation at rupture as the test strain rate is increased. Preliminary examination of force-strain characteristics indicates that, on the average, the material exhibits some type of viscous effect which results in a greater force being produced, for a particular value of strain, under dynamic loading conditions than that produced under quasi-static loading conditions. A great deal of uncertainty exists in defining a priori the tensile properties of viscoelastic materials, such as nylon or dacron, under dynamic loading conditions. Additional uncertainty enters the picture when woven configurations such as suspension,line material are considered. To eliminate these uncertainties, with respect to the Viking parachute configuration, a test program has been conducted to obtain data on the tensile properties of Viking-type suspension-line material over a wide range of strain rates. Based on preliminary examination of these data, the following conclusions can be drawn: 1. Material rupture-load capability decreases as strain-rate is increased. At strain rates above 75 percent/sec, no rupture loads were observed which would meet the minimum tensile strength specification of 880 pounds. 2. The material, on the average, exhibits some type of viscous effect which, for a particular value of strain, produces a greater load under dynamic loading conditions than that produced under quasi-static loading conditions.

Poole, Lamont R.↗
NASA NTRS1990

PdCr Based High Temperature Static Strain Gage

The program at NASA Lewis Research Center to develop a high temperature static strain gage system for the hypersonic vehicle and turbine engine research has emphasized a palladium- 13wt%chromium (PdCr) alloy. Gages made from this alloy are being developed in both fine wire and thin film form. The wire gage system had platinum wire as a temperature compensator and was coated with a special alumina and zirconia mixture overcoat. This PdCr compensated wire gage responded linearly to the imposed strain to at least i000 microstrain. The strain sensitivity of the gage did not vary much with temperature. The apparent strain of this compensated gage was significantly lower than that of the other gages. It varied within 300 microstrain from room temperature to 800 deg. C with a reproducibility within 50 microstrain between thermal cycles to 800 deg. C. This is a significant advance over the 400 deg. C barrier of previous techniques for resistance static strain gages. The sputtered thin film PdCr strain gage, whose size was 8x8 mm and 10 micron thick, has demonstrated the possibility of extending the use of the PdCr strain gage to a temperature of approximately 1000 deg. C.

Lei, Jih-Fen↗
NASA NTRS2017

The Transcriptional Response of Diverse Saccharomyces Cerevisiae Strains to Simulated Microgravity

Spaceflight imposes multiple stresses on biological systems resulting in genome-scale adaptations. Understanding these adaptations and their underlying molecular mechanisms is important to clarifying and reducing the risks associated with spaceflight. One such risk is infection by microbes present in spacecraft and their associated systems and inhabitants. This risk is compounded by results suggesting that some microbes may exhibit increased virulence after exposure to spaceflight conditions. The yeast, S. cerevisiae, is a powerful microbial model system, and its response to spaceflight has been studied for decades. However, to date, these studies have utilized common lab strains. Yet studies on trait variation in S. cerevisiae demonstrate that these lab strains are not representative of wild yeast and instead respond to environmental stimuli in an atypical manner. Thus, it is not clear how transferable these results are to the wild S. cerevisiae strains likely to be encountered during spaceflight. To determine if diverse S. cerevisiae strains exhibit a conserved response to simulated microgravity, we will utilize a collection of 100 S. cerevisiae strains isolated from clinical, environmental and industrial settings. We will place selected S. cerevisiae strains in simulated microgravity using a high-aspect rotating vessel (HARV) and document their transcriptional response by RNA-sequencing and quantify similarities and differences between strains. Our research will have a strong impact on the understanding of how genetic diversity of microorganisms effects their response to spaceflight, and will serve as a platform for further studies.

yeast↗
NASA NTRS2017

The Transcriptional Response of Diverse Saccharomyces Cerevisiae Strains to Simulated Microgravity

Spaceflight imposes multiple stresses on biological systems resulting in genome-scale adaptations. Understanding these adaptations and their underlying molecular mechanisms is important to clarifying and reducing the risks associated with spaceflight. One such risk is infection by microbes present in spacecraft and their associated systems and inhabitants. This risk is compounded by results suggesting that some microbes may exhibit increased virulence after exposure to spaceflight conditions. The yeast, S. cerevisiae, is a powerful microbial model system, and it's response to spaceflight has been studied for decades. However, to date, these studies have utilized common lab strains. Yet studies on trait variation in S. cerevisiae demonstrate that these lab strains are not representative of wild yeast and instead respond to environmental stimuli in an atypical manner. Thus, it is not clear how transferable these results are to the wild S. cerevisiae strains likely to be encountered during spaceflight. To determine if diverse S. cerevisiae strains exhibit a conserved response to simulated microgravity, we will utilize a collection of 100 S. cerevisiae strains isolated from clinical, environmental and industrial settings. We will place selected S. cerevisiae strains in simulated microgravity using a high-aspect rotating vessel (HARV) and document their transcriptional response by RNA-sequencing and quantify similarities and differences between strains. Our research will have a strong impact on the understanding of how genetic diversity of microorganisms effects their response to spaceflight, and will serve as a platform for further studies.

genetic diversity↗
NASA NTRS2018

The Transcriptional Response of Diverse Saccharomyces cerevisiae Strains to Simulated Microgravity

Spaceflight imposes multiple stresses on biological systems resulting in genome-scale adaptations. Understanding these adaptations and their underlying molecular mechanisms is important to clarifying and reducing the risks associated with spaceflight. One such risk is infection by microbes present in spacecraft and their associated systems and inhabitants. This risk is compounded by results suggesting that some microbes may exhibit increased virulence after exposure to spaceflight conditions. The yeast, S. cerevisiae, is a powerful microbial model system, and it's response to spaceflight has been studied for decades. However, to date, these studies have utilized common lab strains. Yet studies on trait variation in S. cerevisiae demonstrate that these lab strains are not representative of wild yeast and instead respond to environmental stimuli in an a typical manner. Thus, it is not clear how transferable these results are to the wild S. cerevisiae strains likely to be encountered during spaceflight. To determine if diverse S. cerevisiae strains exhibit a conserved response to simulated microgravity, we will utilize a collection of 100 S. cerevisiae strains isolated from clinical, environmental and industrial settings. We will place selected S. cerevisiae strains in simulated microgravity using a high-aspect rotating vessel (HARV) and document their transcriptional response by RNA-sequencing and quantify similarities and differences between strains. Our research will have a strong impact on the understanding of how genetic diversity of microorganisms effects their response to spaceflight, and will serve as a platform for further studies.

spaceflight↗
NASA NTRS2024

Isolation, Characterization and Genetic Manipulation of Cold-Tolerant, Manganese-Oxidizing Pseudomonas sp. Strains

Manganese-oxidizing bacteria (MnOB) produce Mn oxide minerals that can be used by humans for bioremediation but the purpose for the bacterium is less clear. This study describes the isolation and characterization of cold-tolerant MnOB strains isolated from a compost pile in Morris, Minnesota, USA: Pseudomonas sp. MS-1 and DSV-1. The strains were preliminarily identified as members of species Pseudomonas psychrophila by 16S rRNA analysis and a multi-locus phylogenetic study using a database of 88 genomes from the Pseudomonas genus. However, the average nucleotide identity (ANI) between these strains and the P. psychrophila sp. CF149 type strain was less than 93%. Thus, the two strains are members of a novel species that diverged from P. psychrophila . DSV-1 and MS-1 are cold tolerant; both grow at 4C but grow faster at 24C. Unlike the mesophilic MnOB P. putida GB-1, both strains are capable of robustly oxidizing Mn at low temperatures. Both DSV-1 and MS-1 genomes contain homologs of several Mn oxidation genes found in P. putida GB-1 ( mnxG, mcoA, mnxS1, mnxS2 and mnxR ). Random mutagenesis by transposon insertion was successfully performed in both strains and identified genes involved in Mn oxidation that were similar to those found in P. putida GB-1. Our results show that MnOB can be isolated from compost, supporting a role for Mn oxidation in plant waste degradation. The novel isolates Pseudomonas spp. DSV-1 and MS-1 both can oxidize Mn at low temperature and likely employ similar mechanisms and regulation as P. putida GB-1.

manganese oxidation↗
DOE OSTI2024

A Microwave Photonics Optical Fiber Method for Measuring Distributed Strain for Hydrologic Applications in the Vadose and Saturated Zones

Distributed strain measurements appear to hold significant potential for monitoring hydrologic processes. Coherence-length-gated Microwave Photonics Interferometry (CMPI) is a distributed sensing technique that measures strain in an optical fiber by reading optical interference phase changes in the microwave domain. The technique provides 10nε resolution when cm spatial resolution is applied. CMPI was used to measure the strain caused by small periodic variations in air pressure (25 Pa amplitude and 4 Hz) in a sand-filled laboratory column used to represent barometric loading in the vadose zone. The strain varied as a periodic function with an amplitude that decreased and a phase that increased with depth. The distribution of amplitude and phase of the strain depended on the water saturation, permeability, and presence of a barrier at the top of the sand. A theoretical analysis suggests that the air pressure diffusivity estimated from pressure data is similar to the diffusivity estimated from the distributed strain. These results indicated that the CMPI distributed strain measurement system could be used to improve monitoring and characterization of the vadose and underlying saturated zone.

Hua, Liwei↗
DOE OSTI2021

Strain rate effects on the mechanical behavior of porous titanium with different pore sizes

High strain-rate (up to 6600 s –1 ) and quasi-static compression tests are conducted on a powder-sintered porous titanium with different pore sizes (mean: 30 μm and 120 μm). In situ X-ray imaging is implemented to characterize the pores-scale deformation dynamics. The yield strength as a function of strain rate exhibits two stages of rate sensitivity, and the transition occurs at 1600 s –1 . X-ray images show that pore compaction and strain localizations occur preferentially at pores oriented perpendicular to the loading direction under quasi-static loading, but become more random under high strain-rate loading as a result of higher driving force and plastic deformation nucleation rate. Here, the more homogeneous nucleation of plastic deformation contributes to the increased rate sensitivity beyond 1600 s –1 . At the same strain rate, the yield strength of porous Ti as well as strain field homogeneity decreases significantly with increasing pore size. The small pore spacing in fine-pored Ti reduces the degree of stress concentrations around pores. Therefore, the higher stress concentrations in coarse-pored Ti lead to an earlier yield of matrix around pores and thus a lower bulk yield strength.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Elastic strain tensor of zirconium hydrides in Zr2.5%Nb pressure tubes by synchrotron X-ray diffraction

Zirconium alloys are used in fuel cladding and structural components of nuclear power plants. Hydrogen enters the Zr matrix during plant operation and precipitates as hydride particles that degrade the mechanical properties of the alloy, limiting service life. Knowledge of the stress state within hydride precipitates is important to understand stress-induced degradation mechanisms such as delayed hydride cracking, but no direct quantification has yet been reported in the literature. Here, measurements are reported of the average elastic strain tensor within δ zirconium hydride precipitates in Zr2.5%Nb pressure tube material from CANDU power plants. Complete intensity and strain pole figures for the hydride were obtained by synchrotron X-ray diffraction experiments on specimens with hydrogen contents ranging from ~100 wt p.p.m. hydrogen to nearly 100% δ-hydride. Zirconium hydride precipitates by a process involving a martensitic transformation, with two hydride variants possible from a single α-Zr grain. A synthetic model of the hydride crystallographic texture allowed the interpretation of the measured strain pole figures and quantification of the elastic strain tensor for both texture components. It was found that the two variants appear in nearly equal proportion but with different stress states, differing in the sign of the shear strain components (~±3000 µ$\epsilon$). This difference is possibly associated with the shear movement of Zr atoms during the phase transformation. This suggests that hydride clusters are composed of stacks of smaller hydrides in alternating hydride variants. Stresses were estimated from a set of rather uncertain hydride elastic constants. Overall, both variants showed compressive strains along the tube axial direction (~5000 µ$\epsilon$). For low hydrogen concentrations, the hydrides' stress tensor is dominated by compressive stresses of ~300 MPa along the axial direction, probably caused by the elongated morphology of hydride clusters along this direction, and variant-dependent shear stresses of ~±100 MPa, probably from the shear movement of the Zr atoms involved in the phase transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Anisotropic Phonon Response of Few-Layer PdSe 2 under Uniaxial Strain

PdSe 2 , an emerging 2D material with a novel anisotropic puckered pentagonal structure, has attracted growing interest due to its layer-dependent electronic bandgap, high carrier mobility, and good air stability. In this work, a detailed Raman spectroscopic study of few-layer PdSe 2 (two to five layers) under the in-plane uniaxial tensile strain up to 3.33% is performed. Two of the prominent PdSe 2 Raman peaks are influenced differently depending on the direction of strain application. Additionally, the A g 1 mode redshifts more than the A g 3 mode when the strain is applied along the a -axis of the crystal, while the A g 3 mode redshifts more than the A g 1 mode when the strain is applied along the b -axis. Such an anisotropic phonon response to strain indicates directionally dependent mechanical and thermal properties of PdSe 2 and also allows the identification of the crystal axes. The results are further supported using first-principles density-functional theory. Interestingly, the near-zero Poisson’s ratios for few-layer PdSe 2 are found, suggesting that the uniaxial tensile strain can easily be applied to few-layer PdSe 2 without significantly altering their dimensions at the perpendicular directions, which is a major contributing factor to the observed distinct phonon behavior. The findings pave the way for further development of 2D PdSe 2 -based flexible electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Interfacial-Strain-Controlled Ferroelectricity in Self-Assembled BiFeO 3 Nanostructures

Self-assembled BiFeO 3 -CoFe 2 O 4 (BFO-CFO) vertically aligned nanocomposites are promising for logic, memory, and multiferroic applications, primarily due to the tunability enabled by strain engineering at the prodigious epitaxial vertical interfaces. However, local investigations directly revealing functional properties in the vicinity of such critical interfaces are often hampered by the size, geometry, microstructure, and concomitant experimental artifacts. Ferroelectric switching in the presence of lateral distributions of vertical strain thus remains relatively unexplored, with broader implications for all strain-engineered functional devices. Additionally, by implementing tomographic atomic force microscopy, 3D domain orientation mapping, and spatially-resolved ferroelectric switching movies, local tensile strain significantly impacts the ferroelectric switching, principally by retarding domain nucleation in the BFO nearest to the vertically epitaxial tensile-strained interfaces. The relaxed centers of the BFO pillars become preferred domain nucleation and growth sites for low biases, with up to an order of magnitude change in the edge:center switching ratio for high biases. The new, multi-dimensional imaging approach—and its corresponding insights especially for directly strained interface effects on local properties—thereby advances the fundamental understanding of polarization switching and provides design principles for optimizing functional response in confined nanoferroic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-Situ SEM High Strain Rate Testing of Large Diameter Micropillars Followed by TEM and EBSD Postmortem Analysis

Background Dislocation dynamic simulations are intended as a tool to understand and predict the mechanical behavior of metallic materials, but its prediction has never been directly verified by experiments due to differences in specimen strain rate and size. Objective In this work, a comprehensive experimental framework is proposed to attempt direct comparison between experiments and discrete dislocation dynamics (DDD) modelling. Methods By integrating high-throughput sample fabrication and a customized testing apparatus, the sample size and strain rate typically employed in DDD simulations are explored experimentally. Constitutive properties such as stress-strain response are measured, and microstructural information is obtained from transmission electron microscopy (TEM) imaging, electron backscatter diffraction (EBSD), and TEM-based orientation mapping. Results Magnesium and copper were selected, as case studies, to demonstrate the newly developed experimental procedure. Measured stress-strain responses for Mg are consistent with those obtained with a miniaturized Hopkison bar experiments. Furthermore, by exploiting the validated workflow, the effect of strain rate on micropillar heterogeneous deformation and associated dislocation plasticity were revealed. Conclusion The work establishes a methodology for the systematic study of not only metals but also other materials and structures at the microscale and high strain rates.

42 ENGINEERING↗
DOE OSTI2020

Influence of strain on SrFeO 3-δ oxidation, reduction, and water dissociation: Insights from ambient pressure X-ray photoelectron spectroscopy

The oxidation and reduction of metal oxides and their interaction with the environment play a critical role in their use for energy storage and conversion applications. The formation of surface adsorbates and their impact on oxide electronic structure can be challenging to probe experimentally, particularly for thin films which enable the study of epitaxial strain but have low surface areas. Here we present a detailed study using ambient pressure X-ray photoelectron spectroscopy of the reduction and oxidation of strained SrFeO 3-δ , induced by changes in temperature, oxygen partial pressure, and water vapor exposure. We find that in comparison to the oxidized lattice, application of tensile strain promotes the formation of oxygen vacancies at the surface, facilitating the subsequent incorporation of oxygen into the lattice in an oxygen environment. While tensile strain does promote the formation of hydroxyls from water dissociation, the kinetics of this process appear more sluggish than on less-strained surfaces, likely due to a competitive surface interaction with oxygen or bulk absorption of hydroxyl species. These findings relating strain, oxygen vacancies, and surface reactivity yield important insight into the surface functionality of oxides for energy conversion and storage applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Influence of strain-rate on the response of elastomeric architected materials

Architected materials have shown substantial promise in impact mitigation and protective applications, and there has accordingly been great interest in better characterizing their response at elevated strain rates due to impact. There remains ambiguity regarding the contribution of inertial and material responses to strain rate sensitivity, and, in particular, when these effects begin to gain dominance in the impact response of an architected material. The response of soft polymer architected materials as a function of strain rate, in particular, has been little investigated. We characterize the experimental impact response of four soft polymer architected lattice geometries across varying strain rates in the intermediate strain rate regime (∼10 3 s −1 ) using split-Hopkinson pressure bar loading and high speed video characterization of the resulting deformation fields. In conclusion, our results highlight the interplay of influence between constituent material, lattice geometry, length scale, and strain rate in determining the onset of significant inertia effects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Infant gut strain persistence is associated with maternal origin, phylogeny, and traits including surface adhesion and iron acquisition

Gut microbiome succession affects infant development. However, it remains unclear what factors promote persistence of initial bacterial colonizers in the developing gut. Here, we perform strain-resolved analyses to compare gut colonization of preterm and full-term infants throughout the first year of life and evaluate associations between strain persistence and strain origin as well as genetic potential. Analysis of fecal metagenomes collected from 13 full-term and 9 preterm infants reveals that infants' initially distinct microbiomes converge by age 1 year. Approximately 11% of early colonizers, primarily Bacteroides and Bifidobacterium, persist during the first year of life, and those are more prevalent in full-term, compared with preterm infants. Examination of 17 mother-infant pairs reveals maternal gut strains are significantly more likely to persist in the infant gut than other strains. Enrichment in genes for surface adhesion, iron acquisition, and carbohydrate degradation may explain persistence of some strains through the first year of life.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Strain-Dependent Surface Defect Equilibria of Mixed Ionic-Electronic Conducting Perovskites

We report understanding the surface defect chemistry and its strain dependency is essential in developing next-generation electrochemical devices. However, due to their nanoscale dimensions, surface defects cannot be accessed by conventional techniques used in bulk defect studies. Here, we constructed the strain-dependent surface defect equilibria (i.e., the Brouwer diagram) of mixed ionic-electronic conducting perovskite oxides with near ambient pressure X-ray absorption spectroscopy. Using coherently strained thin-film La 0.6 Sr 0.4 Fe O3 (LSF) as model systems, we probed their surface defect equilibria at 400 °C in oxygen partial pressures between 1 to 10 -5 Torr. We found that the electron holes on the LSF surfaces have strong oxygen character, regardless of the strain states. Nevertheless, tensile strain makes the LSF surface more reducible than the compressed counterpart. These two observations were then validated using first-principles calculations. Finally, with the aid of thermodynamic analyses, we showed that the strain-dependent surface defect equilibria of LSF can be captured by bulk-like ideal solution defect models with shifted oxygen chemical potentials. The findings and methodology presented in this study enable quantitative determination of the surface defect chemistry, which is crucial to understanding and designing functional surfaces for efficient conversions of energy and fuels.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Moiré-Assisted Strain Transfer in Vertical van der Waals Heterostructures

Strain provides a powerful method to study 2D monolayers and to tune their properties. The same approach also has great potential for van-der-Waals (vdW) heterostructures. However, we need to understand how strain can be applied to vertically stacked vdW structures, for which strain transfer from one layer to the next remains little explored. In our experiment, we fabricated vertical heterostructures consisting of transition metal dichalcogenides (TMDCs) monolayers that were deposited on a flexible substrate. These TMDC heterostructures allowed us to read out separately the strain in each monolayer by photoluminescence measurements. We find that, in TMDC heterostructures with large twist angles (>5°), strain transfer is limited. However, for aligned heterostructures with small twist angles (≤5°), near unity strain transfer efficiency is observed. Here, we correlate this finding with the moiré domains formed in the aligned heterostructures by reconstruction.

2D materials↗