Search NASA⌕ Search

SEARCH · Search NASA

Results for “test support”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Notched and unnotched fatigue behavior of angle-ply graphite/epoxy composites

The axial fatigue behavior of both notched and unnotched graphite/epoxy composites has been studied as part of a continuing research investigation. In unnotched studies, conducted on an AS/3501 laminate, S-N curves were determined for various stress ratios R using simply supported test specimens. Specimens were fatigue tested up to 5 x 10 to the 6th cycles. Apparent fatigue limits in tension-tension and compression-compression cycling occurred at about 60 percent of the respective static strengths. The overall results were expressed in the form of a constant life diagram (that is, a Goodman diagram) showing the relationship between mean stress and stress amplitude. The diagram shows a linear relationship and illustrates a skew-symmetry in fatigue life caused by the relatively low compressive strength of the unrestrained test specimens used. In effect, a maximum in stress amplitude occurs at a positive value of the mean stress.

Ramani, S. V.↗
NASA NTRS1979

Automated management of power systems

APSM (Automated Power System Management) is a technology readiness program underway to develop, evaluate, and demonstrate various techniques involved in power system monitoring, as well as computational and control functions. The demonstration breadboard consists of the Viking Orbiter '75 power subassembly breadboard modified to incorporate dedicated microprocessors and digital interface circuits, as well as test support equipment for both spacecraft and ground computer simulation, fault simulation, and data acquisition.

Imamura, M. S.↗
NASA NTRS1978

Quiet, Clean, Short-Haul, Experimental Engine (QCSEE) Under-The-Wing (UTW) engine acoustic design

The acoustic considerations involved in the low source noise basic engine design and the design procedures followed in the development of the under-the-wing (UTW) engine boilerplate and composite nacelle acoustic treatment designs are presented. Laboratory experiments, component tests, and scale model and engine tests supporting the UTW engine acoustic design are referenced. Acoustic design features include a near-sonic inlet, low fan and core pressure ratios, low fan tip speed, high and low frequency stacked core treatment, multiple thickness treatment, and fan frame and stator vane treatment.

Sowers, H. D.↗
NASA NTRS1978

Quiet, Clean, Short-Haul Experimental Engine (QCSEE) Over-The-Wing (OTW) engine acoustic design

The acoustic considerations involved in the low source noise basic engine design and the design procedures followed in the development of the over-the-wing (OTW) nacelle acoustic treatment design are presented. Laboratory experiments, component tests, and scale model and engine tests supporting the OTW engine acoustic design are referenced. Acoustic design features include a near-sonic inlet, low fan and core pressure ratios, low fan tip speed, high and low frequency stacked core treatment, multiple thickness treatment, and fan frame and stator vane treatment.

Sowers, H. D.↗
NASA NTRS1980

Control of forebody vortex orientation to alleviate side forces

The paper deals with the salient phenomena of three-dimensional symmetric and asymmetric separated flows about typical forbodies at high angles of attack. Particular consideration is given to pressure, forces, and laser vapor screen measurements carried out on a 5-deg semiangle cone in a Mach 0.6 flow under turbulent conditions and supportive tests using a 16-deg semiangle tangent ogive.

Peake, D. J.↗
NASA NTRS1981

Support services for the automative gas turbine project

Support was provided to DOE and NASA in their efforts to inform industry, the public, and Government on the benefits and purpose of the gas turbine programs through demonstrations and exhibits. Tasks were carried out for maintenance, repair, and retrofit of the experimental gas turbine engines being used by NASA in their gas turbine technology programs and in program demonstrations. Limited support testing was conducted at Chrysler in which data were generated on air bearing rotor shaft dynamics, heavy duty variable sheave rubber belts, high temperature elastomer regenerator drive mounting and graphite regenerator seal friction characteristics.

Golec, T.↗
NASA NTRS1982

Propeller tip vortex - A possible contributor to aircraft cabin noise

Wind tunnel model tests support the hypothesis that a propeller tip vortex may subject a downstream wing surface to greater excitation than would be experienced by the aircraft fuselage side wall exposed to propeller-generated noise, ultimately transmitting this structural response to incident dynamic pressure to the cabin interior. Even if structure-borne excitations are less efficient than airborne excitations in the creation of cabin noise, the higher level of the former could still govern cabin noise levels.

Miller, B. A.↗
NASA NTRS1983

An experimental study of supersonic jet shock-associated noise

A new method of screech tone reduction in underexpanded supersonic jets is utilized to determine if the amplitude of screech is related to the level of shock-associated broadband noise. Acoustic measurements show that as the screech tone is reduced, the broadband shock-associated noise may be increased by up to 4dB at some locations. Several experiments were conducted with disturbances put into the flow upstream of the final contraction. Results from these tests support the concept of linkage between the broadband shock noise and screech tones. Some interesting preliminary results were obtained with a disturbance of the flow at several locations downstream of the nozzle. These results are also discussed.

Nagel, R. T.↗
NASA NTRS1983

Experimental measurements of material damping in free fall with tuneable excitation

An experimental method of measuring material damping of a specimen in free fall has been developed. An initially simply-supported test specimen was simultaneously excited and lofted into free fall with a spring-mass launcher. The launcher could be tuned to produce varying initial stress amplitude levels in the specimens. Damping information was obtained from the transient response of the specimens while in free fall in a vacuum. A dynamic model of the launch process was developed which indicates the range of frequency and initial specimen stress amplitude over which tests can be performed. To verify the facility, material damping was measured in 2024-T3 aluminum, and (+ or - 45)2s AS1/3501-6 graphite/epoxy. Free-free frequencies ranged from 20-357 Hz in aluminum, and from 18-171 Hz in the (+ or - 45)2s specimens. Damping values in aluminum were found to be close to theoretical values and independent of stress levels below 130 MPa (18.7 Ksi). Damping ratios in the (+ or - 45)2s graphite/epoxy specimens were found to be largely independent of stress levels below 43.8 MPa (6.35 Ksi) and only slightly dependent on frequency. A small dependence of the frequency of free vibration on specimen stress amplitude was also noted.

Crawley, E. F.↗
NASA NTRS1983

The Information Adaptive System - A demonstration of real-time onboard image processing

The Information Adaptive System (IAS) program has the objective to develop and demonstrate, at the brassboard level, an architecture which can be used to perform advanced signal procesing functions on board the spacecraft. Particular attention is given to the processing of high-speed multispectral imaging data in real-time, and the development of advanced technology which could be employed for future space applications. An IAS functional description is provided, and questions of radiometric correction are examined. Problems of data packetization are considered along with data selection, a distortion coefficient processor, an adaptive system controller, an image processing demonstration system, a sensor simulator and output data buffer, a test support and demonstration controller, and IAS demonstration operating modes.

Thomas, G. L.↗
NASA NTRS1984

Numerical optimization of circulation control airfoil at high subsonic speed

A numerical procedure for optimizing the design of the circulation control airfoil for use at high subsonic speeds is presented. The procedure consists of an optimization scheme coupled with a viscous potential flow analysis for the blowing jet. The desired airfoil is defined by a combination of three baseline shapes (cambered ellipse and cambered ellipse with drooped and spiraled trailing edges). The coefficients of these shapes are used as design variables in the optimization process. Under the constraints of lift augmentation and lift-to-drag ratios, the airfoil, optimized at free-stream Mach 0.54 and alpha = -2 degrees can be characterized as a cambered ellipse with a drooped trailing edge. Experimental tests support the performance improvement predicted by numerical optimization.

Tai, T. C.↗
NASA NTRS1985

Rotordynamics

Research activities that can ultimately lead to optimum rotordynamics design for the space shuttle main engine are outlined. Achievements are summarized in: (1) improving analysis and simulation techniques; (2) defining forces which result from the rotor and surroundings; (3) determining the effect of rubbing; (4) improving balancing; (5) developing damping methods, i.e., eddy-current and damping seals; (6) establishing methods to quantify internal friction; and (7) developing supporting test apparatus.

Schutzenhofer, L. A.↗
NASA NTRS1982

JPL preferred parts list: Reliable electronic components

The JPL Preferred Parts List was prepared to provide a basis for selection of electronic parts for JPL spacecraft programs. Supporting tests for the listed parts were designed to comply with specific spacecraft environmental requirements. The list tabulates the electronic, magnetic, and electromechanical parts applicable to all JPL electronic equipment wherein reliability is a major concern. The parts listed are revelant to equipment supplied by subcontractors as well as fabricated at the laboratory.

Covey, R. E.↗
NASA NTRS1988

Service offerings and interfaces for the ACTS network of Earth stations

The Advanced Communications Satellite (ACTS) is capable of two modes of communication. Mode 1 is a mesh network of Earth stations using baseband-switched, time-division multiple-access (BBS-TDMA) and hopping beams. Mode 2 is a mesh network using satellite-switched, time-division multiple-access (SS-TDMA) and fixed (or hopping) beams. The purpose of this paper is to present the functional requirements and the design of the ACTS Mode 1 Earth station terrestrial interface. Included among the requirements are that: (1) the interface support standard telecommunications service offerings (i.e., voice, video and data at rates ranging from 9.6 kbps to 44 Mbps); (2) the interface support the unique design characteristics of the ACTS communications systems (e.g., the real time demand assignment of satellite capacity); and (3) the interface support test hardware capable of validating ACTS communications processes. The resulting interface design makes use of an appropriate combination of T1 or T3 multiplexers and a small central office (maximum capacity 56 subscriber lines per unit).

Coney, Thom A.↗
NASA NTRS1989

Protoflight photovoltaic power module system-level tests in the space power facility

Work Package Four, which includes the NASA-Lewis and Rocketdyne, has selected an approach for the Space Station Freedom Photovoltaic (PV) Power Module flight certification that combines system level qualification and acceptance testing in the thermal vacuum environment: The protoflight vehicle approach. This approach maximizes ground test verification to assure system level performance and to minimize risk of on-orbit failures. The preliminary plans for system level thermal vacuum environmental testing of the protoflight PV Power Module in the NASA-Lewis Space Power Facility (SPF), are addressed. Details of the facility modifications to refurbish SPF, after 13 years of downtime, are briefly discussed. The results of an evaluation of the effectiveness of system level environmental testing in screening out incipient part and workmanship defects and unique failure modes are discussed. Preliminary test objectives, test hardware configurations, test support equipment, and operations are presented.

Rivera, Juan C.↗
NASA NTRS1989

The dynamics of global positioning system orbits and the determination of precise ephemerides

The suggestion made on the basis of the analytical orbit perturbation theory that the errors in the ephemerides of the GPS satellites are due mostly to resonant effects that can be corrected by adjusting a few parameters in a empirical acceleration formula is tested using simulations and actual data analysis. Data from the Spring 1985 Experiment were used to calculate improved ephemerides, and these ephemerides were used in the estimation of the coordinates of GPS stations within the continental United States, previously positioned with VLBI. The results of this test support the idea that the errors are mostly of a resonant nature and can be corrected.

Colombo, Oscar L.↗
NASA NTRS1989

Protoflight photovoltaic power module system-level tests in the Space Power Facility

Work Package Four, which includes the NASA-Lewis and Rocketdyne, has selected an approach for the Space Station Freedom Photovoltaic (PV) Power Module flight certification that combines system level qualification and acceptance testing in the thermal vacuum environment: the 'protoflight' vehicle approach. This approach maximizes ground test verification to assure system level performance and to minimize risk of on-orbit failures. The preliminary plans for system level thermal vacuum environmental testing of the protoflight PV Power Module in the NASA-Lewis Space Power Facility (SPF) are addressed. Details of the facility modifications to refurbish SPF, after 13 years of downtime, are briefly discussed. The results of an evaluation of the effectiveness of system level environmental testing in screening out incipient part and workmanship defects and unique failure modes are discussed. Preliminary test objectives, test hardware configurations, test support equipment, and operations, are presented.

Rivera, Juan C.↗