Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Design concepts for a high-impedance narrow-band 42 GHz power TWT using a fundamental/forward ladder-based circuit

A low-cost, narrowband, millimeter wave space communications TWT design was studied. Cold test interaction structure scale models were investigated and analyses were undertaken to predict the electrical and thermal response of the hypothetical 200 W TWT at 42 GHz and 21 kV beam voltage. An intentionally narrow instantaneous bandwidth (1%, with the possibility of electronic tuning of the center frequency over several percent) was sought with a highly dispersive, high impedance "forward wave' interaction structure based on a ladder (for economy in fabrication) and nonspace harmonic interaction, for a high gain rate and a short, economically focused tube. The "TunneLadder' interaction structure devised combines ladder properties with accommodation for a pencil beam. Except for the impedance and bandwidth, there is much in common with the millimeter wave helix TWTs which provided the ideal of diamond support rods. The benefits of these are enhanced in the TunneLadder case because of spatial separation of beam interception and RF current heating.

Karp, A.↗
NASA NTRS1983

Recent developments in thermal analysis of large space structures

A numerical procedure for analysis of shadowed space heating of sparse structures, SSQ, is discussed. The SSQ program avoids inordinate computational complexity by confining attention to a single elemental location on a structural member of interest throughout an entire orbital period, proceeding then to similar treatment of individual alternate locations. The procedure considers a spacecraft in circular orbit and assumes fixed-Earth orientation of the spacecraft. Shadow orientation and interval duration, merged shadows, and computation of solar heat flux and thermal response are addressed. The output options of the SSQ FORTRAN 5 program and its efficiency are discussed. Application of the system to the analysis of a parabolic expandable truss antenna is considered.

Oneill, R. F.↗
NASA NTRS1983

Evaluation of Gas-Cooled Pressurized Phosphoric Acid Fuel Cells for Electric Utility Power Generation

Gas cooling is a more reliable, less expensive and a more simple alternative to conventional liquid cooling for heat removal from the phosphoric acid fuel cell (PAFC). The feasibility of gas-cooling was already demonstrated in atmospheric pressure stacks. Theoretical and experimental investigations of gas-cooling for pressurized PAFC are presented. Two approaches to gas cooling, Distributed Gas-Cooling (DIGAS) and Separated Gas-Cooling (SGC) were considered, and a theoretical comparison on the basis of cell performance indicated SGC to be superior to DIGAS. The feasibility of SGC was experimentally demonstrated by operating a 45-cell stack for 700 hours at pressure, and determining thermal response and the effect of other related parameters.

Faroque, M.↗
NASA NTRS1983

Evaluation of gas cooling for pressurized phosphoric acid fuel cell stacks

Gas cooling is a more reliable, less expensive and a more simple alternative to conventional liquid cooling for heat removal from the phosphoric acid fuel cell (PAFC). The feasibility of gas cooling has already been demonstrated in atmospheric pressure stacks. This paper presents theoretical and experimental investigation of gas cooling for pressurized PAFC. Two approaches to gas cooling, Distributed Gas Cooling (DIGAS) and Separated Gas Cooling (SGC) were considered, and a theoretical comparison on the basis of cell performance indicated SGC to be superior to DIGAS. The feasibility of SGC was experimentally demonstrated by operating a 45-cell stack for 700 hours at pressure, and determining thermal response and the effect of other related parameters.

Farooque, M.↗
NASA NTRS1984

Effect of microcracks on the thermal expansion of composite laminates

A finite element analysis was used to quantitatively predict the effect of matrix microcracks in the 90 deg plies of graphite/epoxy composites on the coefficient of thermal expansion in the 0 deg direction, alpha (y) (perpendicular to the cracks). Results were generated for (0m/90n)s, (0/+ or 45/90)s and (0/90/ + or - 45)s graphite/epoxy laminate configurations. Analytical predictions were compared with experimental results for the two quasi-isotropic laminate configurations. Both analytical and experimental results showed that microcracks reduced the effective stiffness of the 90 deg plies, thus causing the laminates, thermal response to be more like that of a (0) laminate. The change in alpha(y) was a function of lamina material properties, microcrack density, fiber orientation, and stacking sequence. A combination of classical lamination theory and finite element analysis was used to predict the effect of microcracks in both the 90 deg and 0 deg plies. Analytical results showed that the addition of microcracks in the 0 deg plies do affect alpha(y), but to a lesser extent than those in the 90 deg plies.

Bowles, D. E.↗
NASA NTRS1984

Measurement of convective heat transfer to solid cylinders inside ventilated shrouds

The influence of ventilated cylindrical shrouds on the convective heat transfer to circular cylinders has been studied experimentally. Geometries studied were similar to those used in commercially available platinum resistance thermometers. Experiments showed that thermal response (convection) was enhanced when the shroud ventilation factor was approximately 20 percent (80 percent solid), and that maximum enhancement occurred when the ventilation holes were located symmetrically on either side of the stagnation lines.

Daryabeigi, K.↗
NASA NTRS1985

Thermal design of the ACCESS erectable space truss

Thermal design requirements for the erectable truss beam to be assembled in-orbit during extra-vehicular activity as part of the ACCESS experiment to take place in 1985-1986 are formulated and assessed. The coatings, insulation, and materials chosen for the structural elements of the beam are detailed. A combined radiation and conduction thermal model reveals that worst-case thermal gradients within the ACCESS structure over plane-to-sun angles of 0 to 80 deg will be less than 29 F, which is within the allowable limit of 50 F. The individual strut insulation concept using aluminized Kapton is shown to offer significant advantages over white paint or a chromic acid anodized surface for controlling the thermal response.

Bradley, O. H., Jr.↗
NASA NTRS1986

Shadowed Space Heating of Sparse Structures

Complete heat-flux and temperature maps computed. Computer program SSQ developed to address and quantify complex, solar-shadowing conditions inherent in sparse, lattice-type space structures. Analysis procedure one of assessing partial shadowing of structural elements by multiple, similar slender members. Program yields schedules of incident-solar, Earth-thermal, and Earth-albedo radiation throughout complete orbit for elemental locations on selected structural members. Thermal response computed in optional routine. Complete heat-flux and temperature mapping obtained by repeated computations for selected elements of interest.

Oneill, J. L.↗
NASA NTRS1983

Transient thermal modeling of the nonscanning ERBE detector

A numerical model to predict the transient thermal response of the ERBE nonscanning wide field of view total radiometer channel was developed. The model, which uses Monte Carlo techniques to characterize the radiative component of heat transfer, is described and a listing of the computer program is provided. Application of the model to simulate the actual blackbody calibration procedure is discussed. The use of the model to establish a real time flight data interpretation strategy is recommended. Modification of the model to include a simulated Earth radiation source field and a filter dome is indicated.

Mahan, J. R.↗
NASA NTRS1985

Constitutive modelling of lubricants in concentrated contacts at high slide to roll ratios

A constitutive lubricant friction model for rolling/sliding concentrated contacts such as gears and cams was developed, based upon the Johnson and Tevaarwerk fluid rheology model developed earlier. The friction model reported herein differs from the earlier rheological models in that very large slide to roll ratios can now be accommodated by modifying the thermal response of the model. Also the elastic response of the fluid has been omitted from the model, thereby making it much simpler for use in the high slide to roll contacts. The effects of this simplification are very minimal on the outcome of the predicted friction losses (less than 1%). In essence then the lubricant friction model developed for the high slide to roll ratios treats the fluid in the concentrated contact as consisting of a nonlinear viscous element that is pressure, temperature, and strain rate dependent in its shear response. The fluid rheological constants required for the prediction of the friction losses at different contact conditions are obtained by traction measurements on several of the currently used gear lubricants. An example calculation, using this model and the fluid parameters obtained from the experiments, shows that it correctly predicts trends and magnitude of gear mesh losses measured elsewhere for the same fluids tested here.

Tevaarwerk, J. L.↗
NASA NTRS1986

Space Shuttle Orbiter nose cap thermal analysis

The results of a Space Shuttle Orbiter nose cap entry aeroheating assessment, thermal analysis, and correlation of flight data using multidimensional thermal math models (TMM's) and a chemically reacting boundary-layer program are described in this paper. The object of this study was to verify and revise, if required, the nose cap design heating methods and the TMM's used for flight certification. Flight temperature measurements from two Orbiter vehicles, Columbia and Challenger, have been used in this analysis and provide the basis for verification and correlation of the aerothermodynamic environment. Nose cap thermal response predictions, using TMM's verified from certification tests, show that the aerothermodynamic environment can be satisfactorily predicted using accepted analytical methods.

Curry, D. M.↗
NASA NTRS1986

Role of seasonality in the evolution of climate during the last 100 million years

A simple climate model has been used to calculate the effect of past changes in the land-sea distribution on the seasonal cycle of temperatures during the last 100 million years. Modeled summer temperature decreased over Greenland by more than 10 C and over Antarctica by 5 to 8 C. For the last 80 million years, this thermal response is comparable in magnitude to estimated atmospheric carbon dioxide effects. Analysis of paleontological data provides some support for the proposed hypothesis that large changes due to seasonality may have sometimes resulted in an ice-free state due to high summer temperatures rather than year-round warmth. Such 'cool' nonglacials may have prevailed for as much as one-third of the last 100 million years.

Crowley, T. J.↗
NASA NTRS1987

Microstructure and Aging of Powder-Metallurgy Al Alloys

Report describes experimental study of thermal responses and aging behaviors of three new aluminum alloys. Alloys produced from rapidly solidified powders and contain 3.20 to 5.15 percent copper, 0.24 to 1.73 percent magnesium, 0.08 to 0.92 percent iron, and smaller amounts of manganese, nickel, titanium, silicon, and zinc. Peak hardness achieved at lower aging temperatures than with standard ingot-metallurgy alloys. Alloys of interest for automobile, aircraft, and aerospace applications.

Blackburn, L. B.↗
NASA NTRS1986

Temperature distribution in the crust and mantle

In an attempt to understand the temperature distribution in the earth, experimental constraints on the geotherm in the crust and mantle are considered. The basic form of the geotherm is interpreted on the basis of two dominant mechanisms by which heat is transported in the earth: (1) conduction through the rock, and (2) advection by thermal flow. Data reveal that: (1) the temperature distributions through continental lithosphere and through oceanic lithosphere more than 60 million years old are practically indistinguishable, (2) crustal uplift is instrumental in modifying continental geotherms, and (3) the average temperature through the Archean crust and mantle was similar to that at present. It is noted that current limitations in understanding the constitution of the lower mantle can lead to significant uncertainties in the thermal response time of the planetary interior.

Jeanloz, R.↗
NASA NTRS1987

Critical fluid light scattering

Thermal fluctuations give rise to a host of thermodynamic anomalies near critical points. The background for these phenomena is presented, and an experiment design on STS flight experiment called 'Zeno' described. The objective is to measure the decay rates of critical density fluctuations in a simple fluid (xenon) very near its liquid-vapor critical point using laser light-scattering and photon-correlation spectroscopy. Such experiments have been limited on earth by the presence of gravity, which causes large density gradients in the sample. Fluctuation decay rates in xenon will be measured at least 100 times closer to the critical point than is possible on earth. This will require taking data as close as 145 microK to the critical temperature (Tc = 289.72 K), after locating it to + or - 10 microK. The minimum mission time of 100 hours will allow a complete range of temperature points to be covered, limited by the thermal response of the sample. An essential part of the apparatus is the thermostat. Its design principles and key features are given together with some observed performance characteristics of a prototype: + or - 20 microK stability for 18 hours, and one minute programmed step response for steps less than 10 mK.

Gammon, Robert W.↗
NASA NTRS1988

Critical fluid light scattering

The objective is to measure the decay rates of critical density fluctuations in a simple fluid (xenon) very near its liquid-vapor critical point using laser light scattering and photon correlation spectroscopy. Such experiments were severely limited on Earth by the presence of gravity which causes large density gradients in the sample when the compressibility diverges approaching the critical point. The goal is to measure fluctuation decay rates at least two decades closer to the critical point than is possible on earth, with a resolution of 3 microK. This will require loading the sample to 0.1 percent of the critical density and taking data as close as 100 microK to the critical temperature. The minimum mission time of 100 hours will allow a complete range of temperature points to be covered, limited by the thermal response of the sample. Other technical problems have to be addressed such as multiple scattering and the effect of wetting layers. The experiment entails measurement of the scattering intensity fluctuation decay rate at two angles for each temperature and simultaneously recording the scattering intensities and sample turbidity (from the transmission). The analyzed intensity and turbidity data gives the correlation length at each temperature and locates the critical temperature. The fluctuation decay rate data from these measurements will provide a severe test of the generalized hydrodynamic theories of transport coefficients in the critical regions. When compared to equivalent data from binary liquid critical mixtures they will test the universality of critical dynamics.

Gammon, Robert W.↗
NASA NTRS1988

Tersail - A numerical model for combined analysis of vegetation canopy bidirectional reflectance and thermal emissions

A modification of the Tergra model (Soer, 1977) is presented, which incorporates the scattering from arbitrarily inclined leaves canopy reflectance model (Verhoef and Bunnik, 1981) for the calculation of albedo and canopy resistance. The combined model, known as Tersail, is capable of simulating the relationship between the bidirectional reflectance and the thermal response of a canopy. The accuracy of the model is tested using data over wheat canopies in Phoenix, Arizona, showing that the model is a good simulator of canopy temperatures under a variety of conditions.

Hope, Allen S.↗