Search NASA⌕ Search

SEARCH · Search NASA

Results for “AXIAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Analysis of Turbulent Flow and Heat Transfer in Noncircular Passages

Previous work on turbulent heat transfer and flow in tubes was generalized and applied to flow in non-circular passages of equilateral triangular and square cross section. Expressions for eddy diffusivity that had been verified for flow and heat transfer in tubes were assumed to apply in general along lines normal to a wall. Velocity distributions, wall shear-stress distributions, and friction factors, as well as wall heat-transfer distributions, wall temperature distributions, and average heat-transfer coefficients were calculated. In addition, results from a previous analysis for axial flow between rods were compared with new experimental data. For calculating wall temperature distributions, uniform heat generation in the passage wall and uniform heat transfer at the outer surface were assumed. The application of the results is restricted to moderately small peripheral wall temperature variations. Calculations were made for Reynolds numbers from 20,000 to 900,000 and Prandtl numbers from 0.73 to 300. Results show that velocities, shear stresses, and heat transfer in the region near the corner were lower than average values and were zero at the corner. Friction factors and average Nusselt numbers were lower than in a tube.

Taylor, Maynard F.↗

Nonlinear analysis of laminated fibrous composites

A computerized analysis of the nonlinear behavior of fibrous composite laminates including axial loading, thermal loading, temperature dependent properties, and edge effects is presented. Ramberg-Osgood approximations are used to represent lamina stress-strain behavior and percent retention curves are employed to model the variation of properties with temperature. Balanced, symmetric laminates comprised of either boron/epoxy, graphite/epoxy, or borsic-aluminum are analyzed using a quasi-three-dimensional finite element analysis. Results are presented for the interlaminar stress distributions in cross-ply, angle-ply, and more complex laminates. Nonlinear stress-strain curves for a variety of composite laminates in tension and compression are obtained and compared to other existing theories and experimental results.

Renieri, G. D.↗

The University of Minnesota oscillating flow experiments

Hot-wire anemometry techniques used to document laminar-to-turbulent transition in oscillating flow are discussed, and two transition mechanisms proposed by Seume (1988) are reviewed. Reliable near-wall data, and the convergence of ensemble-averaged velocities and rms velocity fluctuations will aid in evaluating wall shear stresses and calculating various boundary-layer parameters. Special consideration was given to a detailed measurement program which documents transition at different axial positions for the space power research engine (SPRE) operating point. Future work on the effect of entry geometry and measurements of heat transfer are outlined. In order to better simulate flow conditions in actual Stirling engine heat exchangers, the effects of various inflow geometries are investigated. Once the hydrodynamic conditions in the test section are documented, a measurement program to assess the effect of flow oscillation on heat transfer will commence.

Friedman, G. T.↗

Characterization of Damage in Triaxial Braid Composites Under Tensile Loading

Carbon fiber composites utilizing flattened, large tow yarns in woven or braided forms are being used in many aerospace applications. Their complex fiber architecture and large unit cell size present challenges in both understanding deformation processes and measuring reliable material properties. This report examines composites made using flattened 12k and 24k standard modulus carbon fiber yarns in a 0 /+60 /-60 triaxial braid architecture. Standard straight-sided tensile coupons are tested with the 0 axial braid fibers either parallel with or perpendicular to the applied tensile load (axial or transverse tensile test, respectively). Nonuniform surface strain resulting from the triaxial braid architecture is examined using photogrammetry. Local regions of high strain concentration are examined to identify where failure initiates and to determine the local strain at the time of initiation. Splitting within fiber bundles is the first failure mode observed at low to intermediate strains. For axial tensile tests splitting is primarily in the 60 bias fibers, which were oriented 60 to the applied load. At higher strains, out-of-plane deformation associated with localized delamination between fiber bundles or damage within fiber bundles is observed. For transverse tensile tests, the splitting is primarily in the 0 axial fibers, which were oriented transverse to the applied load. The initiation and accumulation of local damage causes the global transverse stress-strain curves to become nonlinear and causes failure to occur at a reduced ultimate strain. Extensive delamination at the specimen edges is also observed.

Littell, Justin D.↗

Structural Integrity of a Wind Tunnel Balance

The National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) has been designing strain-gage balances for utilization in wind tunnels since its inception. The utilization of balances span over a wide variety of aerodynamic tests. A force balance is an inherently critically stressed component due to the requirements of measurement sensitivity. Research and analyses are done in order to investigate the structural integrity of the balances as well as developing an understanding of their performance in order to enhance their capability. Maximum loading occurs when all 6 components of the loads are applied simultaneously with their maximum value allowed (limit load). This circumstance normally does not occur in the wind tunnel. However, if it occurs, is the balance capable of handling the loads with an acceptable factor of safety? LaRC Balance 1621 was modeled and meshed in PATRAN for analysis in NASTRAN. For a complete analysis, it is necessary to consider all the load cases as well as use dense mesh near all the edges. Because of computer limitations, it is not possible to have one model with the dense mesh near all edges. In the present study, a dense mesh is limited to the surface corners where the cage and axial sections meet. Four different load combinations are used for the current analysis. Linear analysis is performed for each load case. In the case where the stress value is above linear elastic region, it is necessary to perform nonlinear analysis. It is also important to investigate the variables limiting the structural integrity of the balances. In order to investigate the possibility of modifying the existing balances to enhance the structural integrity, some modifications are done on this balance. The structural integrity of the balance after modification is investigated.

Karkehabadi, R.↗

Reliability Assessment of Graphite Specimens under Multiaxial Stresses

An investigation was conducted to predict the failure strength response of IG-100 nuclear grade graphite exposed to multiaxial stresses. As part of this effort, a review of failure criteria accounting for the stochastic strength response is provided. The experimental work was performed in the early 1990s at the Oak Ridge National Laboratory (ORNL) on hollow graphite tubes under the action of axial tensile loading and internal pressurization. As part of the investigation, finite-element analysis (FEA) was performed and compared with results of FEA from the original ORNL report. The new analysis generally compared well with the original analysis, although some discrepancies in the location of peak stresses was noted. The Ceramics Analysis and Reliability Evaluation of Structures Life prediction code (CARES/Life) was used with the FEA results to predict the quadrants I (tensile-tensile) and quadrant IV (compression-tension) strength response of the graphite tubes for the principle of independent action (PIA), the Weibull normal stress averaging (NSA), and the Batdorf multiaxial failure theories. The CARES/Life reliability analysis showed that all three failure theories gave similar results in quadrant I but that in quadrant IV, the PIA and Weibull normal stress-averaging theories were not conservative, whereas the Batdorf theory was able to correlate well with experimental results. The conclusion of the study was that the Batdorf theory should generally be used to predict the reliability response of graphite and brittle materials in multiaxial loading situations.

Sookdeo, Steven↗

Aerodynamic Analysis of Multistage Turbomachinery Flows in Support of Aerodynamic Design

This paper summarizes the state of 3D CFD based models of the time average flow field within axial flow multistage turbomachines. Emphasis is placed on models which are compatible with the industrial design environment and those models which offer the potential of providing credible results at both design and off-design operating conditions. The need to develop models which are free of aerodynamic input from semi-empirical design systems is stressed. The accuracy of such models is shown to be dependent upon their ability to account for the unsteady flow environment in multistage turbomachinery. The relevant flow physics associated with some of the unsteady flow processes present in axial flow multistage machinery are presented along with procedures which can be used to account for them in 3D CFD simulations. Sample results are presented for both axial flow compressors and axial flow turbines which help to illustrate the enhanced predictive capabilities afforded by including these procedures in 3D CFD simulations. Finally, suggestions are given for future work on the development of time average flow models.

Adamczyk, John J.↗

Analytical and experimental study of mean flow and turbulence characteristics inside the passages of an axial flow inducer

The inviscid and viscid effects existing within the passages of a three bladed axial flow inducer operating at a flow coefficient of 0.065 are investigated. The blade static pressure and blade limiting streamline angle distributions were determined and the three components of mean velocity, turbulence intensities, and turbulence stresses were measured at locations inside the inducer blade passage utilizing a rotating three sensor hotwire probe. Applicable equations were derived for the hotwire data reduction analysis and solved numerically to obtain the appropriate flow parameters. The three dimensional inviscid flow in the inducer was predicted by numerically solving the exact equations of motion, and the three dimensional viscid flow was predicted by incorporating the dominant viscous terms into the exact equations. The analytical results are compared with the experimental measurements and design values where appropriate. Radial velocities are found to be of the same order as axial velocities within the inducer passage, confirming the highly three dimensional characteristic of inducer flow. Total relative velocity distribution indicate a substantial velocity deficiency near the tip at mid-passage which expands significantly as the flow proceeds toward the inducer trailing edge. High turbulence intensities and turbulence stresses are concentrated within this core region. Considerable wake diffusion occurs immediately downstream of the inducer trailing edge to decay this loss core. Evidence of boundary layer interactions, blade blockage effects, radially inward flows, annulus wall effects, and backflows are all found to exist within the long, narrow passages of the inducer.

Gorton, C. A.↗

A Rotary Flow Channel for Shear Stress Sensor Calibration

A proposed shear sensor calibrator consists of a rotating wheel with the sensor mounted tangential to the rim and positioned in close proximity to the rim. The shear stress generated by the flow at the sensor position is simply tau(sub omega) = (mu)r(omega)/h, where mu is the viscosity of the ambient gas, r the wheel radius, omega the angular velocity of the wheel, and h the width of the gap between the wheel rim and the sensor. With numerical values of mu = 31 (mu)Pa s (neon at room temperature), r = 0.5 m, omega = 754 /s (7200 rpm), and h = 50.8 m, a shear stress of tau(sub omega) = 231 Pa can be generated. An analysis based on one-dimensional flow, with the flow velocity having only an angular component as a function of the axial and radial coordinates, yields corrections to the above simple formula for the curvature of the wheel, flatness of the sensor, and finite width of the wheel. It is assumed that the sensor mount contains a trough (sidewalls) to render a velocity release boundary condition at the edges of the rim. The Taylor number under maximum flow conditions is found to be 62.3, sufficiently low to obviate flow instability. The fact that the parameters entering into the evaluation of the shear stress can be measured to high accuracy with well-defined uncertainties makes the proposed calibrator suitable for a physical standard for shear stress calibration.

Zuckerwar, Allan J.↗

GENERAL INSTABILITY OF ORTHOGONALLY STIFFENED CYLINDRICAL SHELLS

Earlier research at the National Aeronautics Research Institute (N.L.R.), Amsterdam, which forms the basis of recent work is reviewed. This early work refers to 2 schemes: the orthotropic shell and, in view of buckling modes where the half wave length is of the order of the ring distance, the shell with continuously distributed stringers and discrete rings. Linear theory is considered to be adequate for these structures, where the imperfections are small in comparison to the height of the ring sections. Recent developments account for pressure difference in addition to axial compression, for the correct stiffness matrix of skin panels in the post-buckling stage and for stringer bending due to hoop stresses in the skin, which are of importance as has been shown by the investigation of the post-buckling behaviour. Numerical data for the stiffness matrix of skin panels have been established. Numerical evaluation of the stability equation has not been performed as yet.

SHELL STABILITY↗

Turbulence characteristics of swirling flowfields

The time mean and turbulence properties of a confined swirling jet using the six orientation, single hot wire technique were obtained. The effect of swirl on a confined, expanding jet is to reduce the size of the corner recirculation zone and generate a central recirculation zone followed by a precessing vortex core. The effect of introducing a contraction nozzle of area ratio four, located two test section diameters downstream of the inlet, is to dramatically reduce the size and shape of the central recirculation zone for the swirling flows considered. The shear stresses are found to increase by an order of magnitude in the region of the contraction nozzle because of large radial gradients of axial velocity. Reduction of the expansion ratio to D/o = 1 causes the time mean flow field to be homogeneous throughout the entire test section with the tangential velocity dominating in the swirling cases. No recirculation zones were observed for these particular flows. Turbulence levels and dissipation rates were found to be low except in the entrance regions and in areas of acceleration in the swirling flow cases.

Jackson, T. W.↗

Time-temperature-stress dependence of boron fiber deformation

The time-dependent deformation of boron fibers over the temperature range from -190 to 800 C is studied by flexural stress relaxation and flexural internal friction techniques on 203-micron diam specimen fibers commercially produced by chemical vapor deposition (CVD) on a 13-micron tungsten substrate. It is shown that up to at least 800 C all nonelastic behavior observed during axial deformation of CVD boron fibers can be explained solely by anelastic mechanisms and that although creep strains are small, boron fiber anelasticity can produce significant mechanical effects which would otherwise be neglected under the elastic approximation. Relations are obtained to demonstrate the considerable effects of anelasticity on such fiber/composite properties as modulus, creep, creep recovery, stress relaxation, and damping capacity. For an elastic-core/anelastic-sheath model, boron fibers on tungsten substrates are shown to have predictable fracture stresses for time-temperature conditions ranging from impact to long-time stress rupture. Possible techniques for altering these stresses are discussed.

Dicarlo, J. A.↗

On the cyclic stress-strain behaviour of a Ni-base superalloy at room temperature

The cyclic stress-strain behavior of Nimonic alloy PE16 was studied at room temperature and at different aging conditions to determine whether the plateau in the cyclic stress-strain curve (CSSC) reported by Arbuthnot (1982) is typical of the room temperature behavior and/or some specific initial microstructural states. Specimen blanks were heat-treated in batches in Ar/H2 (98/2) atmosphere to produce gamma-prime precipitates of different average sizes, but with the volume fraction of gamma-prime precipitates kept constant at about 7 percent at all the heat-treatment conditions. Total axial strain controlled LCF tests were conducted under fully reversed loading (R = -1) at a constant strain rate of 0.004/s, using a servohydraulic machine. The load response in tension and compression was recorded continually, and stress-strain hysteresis loops were recorded at frequent intervals. In the present investigation, the CSSCs of the P16 alloy at room temperature did not display the plateaus reported by Arbuthnot.

Singh, Vakil↗

A novel design for a hybrid space manipulator

Described are the structural design, kinematics, and characteristics of a robot manipulator for space applications and use as an articulate and powerful space shuttle manipulator. Hybrid manipulators are parallel-serial connection robots that give rise to a multitude of highly precise robot manipulators. These manipulators are modular and can be extended by additional modules over large distances. Every module has a hemispherical work space and collective modules give rise to highly dexterous symmetrical work space. Some basic designs and kinematic structures of these robot manipulators are discussed, the associated direct and inverse kinematics formulations are presented, and solutions to the inverse kinematic problem are obtained explicitly and elaborated upon. These robot manipulators are shown to have a strength-to-weight ratio that is many times larger than the value that is currently available with industrial or research manipulators. This is due to the fact that these hybrid manipulators are stress-compensated and have an ultralight weight, yet, they are extremely stiff due to the fact that force distribution in their structure is mostly axial. Actuation is prismatic and can be provided by ball screws for maximum precision.

Shahinpoor, MO↗

Turbulence measurements of high shear flow fields in a turbomachine seal configuration

The mean velocity and Reynolds stress tensor throughout a whirling annular seal are presented. The data was collected with a three dimensional laser Doppler velocimeter using phase averaging. Two axial flow conditions (Re = 12,000 and 24,000) were studied at one shaft speed (Ta = 6,600). The eccentricity and whirl ratios were 50 and 100 percent, respectively. There is a region of high axial momentum in this region is higher in the low Reynolds number case due to an axial recirculation zone that occurs on the suction side of the rotor at the inlet. The recirculation zone does not occur in the high Reynolds number case. At both Reynolds numbers, there is a recirculation zone on the rotor surface in the pressure side of the inlet. This recirculation zone extends from 20 to 200 degrees rotor zenith in the tangential direction, and is one third of a clearance wide radially. The high Reynolds number recirculation zone is 1.5 mean clearances long, while the low Reynolds number zone extends 2 mean clearances downstream. When compared to previous studies, it is apparent that the tangential momentum is no greater for a seal with whirl than for one without if other parameters are constant. Areas of high tangential momentum occur in the clearance where the axial momentum is low. Average exit plane tangential velocities in the high Reynolds number case are 1.5 times greater than those in the other flow case. These results are in general agreement with predictions made by other investigators.

Morrison, Gerald L.↗

Three-component velocity measurements in an axisymmetric jet using LDV

A three-component laser Doppler velocimeter (LDV) has been used to acquire three-dimensional mean and fluctuating velocity measurements in a low-speed air jet entering a stagnant ambient, over the first 16 jet exit diameters along the jet centerline trajectory. These data are consistent with previous measurements in axisymmetric, turbulent jets. A comparison between radial traverses through the jet centerline in two orthogonal directions is also self-consistent. Mean velocity and Reynolds stress data approach a self-preserving behavior by x/D = 16. However, the RMS turbulence fluctuations were not yet self-preserving at this axial location, as expected based upon previous experimental studies. These data confirm the ability to obtain reliable three-dimensional velocity data using the present three-dimensional LDV system.

Kuhlman, John M.↗

An Improved Analysis of the Thermal Buckling of Silicon Sheet

Buckling problems on the production of wide and thin silicon sheet are discussed. Buckling occurs in all of the processes which are investigated for their potential in mass producing wide silicon sheet for use in making solar cells. It is a fact that the processes which produce good ribbon 2 cm in width do not yield the same quality product at 10 cm in width. Buckling develops precisely because the sheets are wide and very very thin. The buckling of very thin cantilever plates due to temperature variations in the axial direction is considered. The temperature variation in the width direction was determined. Axial temperature variations which cause very thin plates to buckle in a torsional mode are demonstrated. It is assumed that the particular variation of the stress function in the width direction and thereafter the analysis is exact.

Dillon, O. W., Jr.↗

Free edge effects in laminated composites

The fundamental mechanics of free-edge effects in laminated fiber-reinforced composites is examined, reviewing the results of recent experimental and analytical investigations. The derivation of the governing equations for the basic problem is outlined, including the equilibrium and mismatch conditions and the elasticity formulation, and experimental data on axial displacement and shear strain in angle-ply laminates are summarized. Numerical predictions of free-edge deformation and interlaminar and through-thickness stress distributions are presented for cross-ply, angle-ply, and quasi-isotropic laminates, and the mechanisms of edge damage and failure in angle-ply laminates are briefly characterized. Extensive diagrams, drawings, graphs, and photographs are provided.

Herakovich, C. T.↗