SEARCH · Search NASA

Results for “Aerodynamic Interference”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Aerodynamics on a transport aircraft type wing-body model

The DFLR-F4 wing-body combination is studied. The 1/38 model is formed by a 9.5 aspect ratio transonic wing and an Airbus A 310 fuselage. The F4 wing geometrical characteristics are described and the main experimental results obtained in the S2MA wind tunnel are discussed. Both wing-fuselage interferences and viscous effects, which are important on the wing due to a high rear loading, are investigated by performing 3D calculations. An attempt is made to find their limitations.

Schmitt, V.↗

NASA NTRS1973

The application of general aerodynamic lifting surface elements to problems in unsteady transonic flow

A study was conducted to investigate the feasibility of using combined subsonic and supersonic linear theory as a means for solving unsteady transonic flow problems in an economical and yet realistic manner. With some modification, existing linear theory methods are combined into a single program and a simple algorithm is derived for determining interference between lifting surface elements of different Mach number. The method is applied to a wide variety of problems for which measured unsteady pressure distributions and Mach number distributions are available. By comparing theory and experiment, the transonic method solutions show a significant improvement over uniform flow solutions. It is concluded that with these refinements the method will provide a means for performing realistic transonic flutter and dynamic response analyses at costs which are compatible with current linear theory based solutions.

Cunningham, A. M., Jr.↗

NASA NTRS1972

Reduction of wave drag by antisymmetric arrangement of wings and bodies.

The wave interference effects for bodies or wings in a mirror-symmetric arrangement, and in an antisymmetric arrangement are discussed. It is shown that while in the case of a mirror-symmetric arrangement large adverse interference effects can be observed, antisymmetric arrangements provide comparatively much smaller wave drags. The single continuous wing panels also adapt themselves more readily to varying angles of obliquity, and hence, to varying flight speeds. A detailed review is presented of the previous work on the aerodynamic properties and flight stability of oblique elliptic wing combinations. A possible mode of application of these combinations to transport aircraft operating at moderate supersonic speeds is suggested.

Jones, R. T.↗

NASA NTRS1982

Wing flap-type control effectiveness and effects of control hinge gap seals for a supercritical wing

Wind-tunnel tests were made to investigate the control effectiveness of wing trailing-edge flap-type aerodynamic controls for a supercritical wing. The tests determined the effects of spanwise flap control location, two different wing transition grit location patterns, magnitude of angular control deflection, control hinge moments and control hinge gap seals. Results show that the inboard flap position deflections caused interference rearward at the vertical tail, and that all flap positions for deflections in one direction only caused interference at the horizontal tail at a higher than design Mach number. Changes in wing transition grit pattern caused significant changes to static longitudinal characteristics and longitudinal control effectiveness.

Anglin, E. L.↗

NASA NTRS1962

Simplified Free-Flight Testing in a Conventional Wind Tunnel

In order to incorporate the advantages of ballistic range testing with the convenience of wind tunnel testing, simplified techniques have been developed at the Jet Propulsion Laboratory (JPL) for free-flight testing of models in a conventional wind tunnel. So far, only a small number of the many possibilities have been investigated, but the preliminary results indicate that such techniques are both practical and useful. The model to be investigated is suspended on a single traverse wire at the upstream end of the test section window, then is released from this position by causing the wire to break within the model. High speed motion pictures taken of the model oscillating during its travel across the viewing area make it possible to determine various aerodynamic parameters such as drag, lift, pitching moment, and pitch damping in much the same manner as is done in ballistic range testing. Also, a spark schlieren photograph can be taken of the model in flight in order to observe details of an undisturbed (from support interference) wake.

FREE FLIGHT↗

NASA NTRS1984

Aerodynamic canard/wing parametric analysis for general aviation applications

Vortex panel and vortex lattice methods have been utilized in an analytic study to determine the two- and three-dimensional aerodynamic behavior of canard and wing configurations. The purpose was to generate data useful for the design of general aviation canard aircraft. Essentially no two-dimensional coupling was encountered and the vertical distance between the lifting surfaces was found to be the main contributor to interference effects of the three-dimensional analysis. All canard configurations were less efficient than a forward wing with an aft horizontal tail, but were less sensitive to off-optimum division of total lift between the two surfaces, such that trim drag could be less for canard configurations. For designing a general aviation canard aircraft, results point toward large horizontal and vertical distance between the canard and wing, a large wing-to-canard area ratio, and with the canard at a low incidence angle relative to the wing.

Keith, M. W.↗

NASA NTRS1974

The effect of canard leading edge sweep and dihedral angle on the longitudinal and lateral aerodynamic characteristic of a close-coupled canard-wing configuration

A generalized wind-tunnel model, with canard and wing planforms typical of highly maneuverable aircraft, was tested in the Langley high-speed 7- by 10-foot tunnel at a Mach number of 0.30. The test was conducted in order to determine the effects of canard sweep and canard dihedral on canard-wing interference at high angles of attack. In general, the effect of canard sweep on lift is small up to an angle of attack of 16 deg. However, for angles of attack greater than 16 deg, an increase in the canard sweep results in an increase in lift developed by the canard when the canard is above or in the wing chord plane. This increased lift results in a lift increase for the total configuration for the canard above the wing chord plane. For the canard in the wing chord plane, the increased canard lift is partially lost by increased interference on the wing.

Gloss, B. B.↗

NASA NTRS1975

Effect of wing planform and canard location and geometry on the longitudinal aerodynamic characteristics of a close-coupled canard wing model at subsonic speeds

A generalized wind-tunnel model with canard and wing planforms typical of highly maneuverable aircraft was tested in the Langley 7- by 10-foot high-speed tunnel at a Mach number of 0.30 to determine the effect of canard location, canard size, wing sweep, and canard strake on canard-wing interference to high angles of attack. The major results of this investigation may be summarized as follows: the high-canard configuration (excluding the canard strake and canard flap), for both the 60 deg and 44 deg swept leading-edge wings, produced the highest maximum lift coefficient and the most linear pitching-moment curves; substantially larger gains in the canard lift and total lift were obtained by adding a strake to the canard located below the wing chord plane rather than by adding a strake to the canard located above the wing chord plane.

Gloss, B. B.↗

NASA NTRS1976

A quadrilateral vortex method applied to configurations with high circulation

A quadrilateral vortex-lattice method is briefly described for calculating the potential flow aerodynamic characteristics of high-lift configurations. It incorporates an iterative scheme for calculating the deformation of forcefree wakes, including wakes from side edges. The method is applicable to multiple lifting surfaces with part-span flaps deflected, and can include ground effect and wind-tunnel interference. Numerical results, presented for a number of high-lift configurations, demonstrate rapid convergence of the iterative technique. The results are in good agreement with available experimental data.

Maskew, B.↗

NASA NTRS1989

A flow visualization and aerodynamic force data evaluation of spanwise blowing on full and half span delta wings

A wind-tunnel investigation has been performed to quantify the effects of a jet on the leading-edge vortices generated by a 70-deg-sweep sharp-edged delta wing at low Reynolds numbers. Efforts were made ot optimize the jet nozzle position with respect to maximum lift increments. Both half-span force-balance testing and half- and full-span flow visualization tests were conducted. Two angles of attack were investigated, 30 and 35 deg, at Reynolds numbers of 150,000 and 200,000. Aerodynamic enhancement, including lift and drag gains of about 20 and 17 percent respectively, were measured. Results indicate an optimum jet nozzle location to be close to the leading edge, tangent to the upper wing surface, and in a direction aligned parallel to the leading edge. Nozzle interference effects, especially near the apex, were not negligible.

Visser, K. D.↗

NASA NTRS1961

A Wind-Tunnel Investigation of a Transonic-Transport Configuration Utilizing Drag-Reducing Devices at Mach Numbers from 0.20 to 1.03

The static longitudinal stability and control and lateral characteristics of a transonic-transport model, incorporating recent drag-reducing devices, has been investigated in the Langley 8-foot transonic pressure tunnel. The wing was cambered, had a thickened root and a taper ratio of 0.3. Wing sweepback angles of 45 degrees and 40 degrees were investigated with corresponding aspect ratios of 7 and 8, respectively. Modifications to the model for reducing the drag were: a forward fuselage addition and special bodies (four big enough to house jet engines) added to the upper surface of the wing. Other components and changes investigated included an empennage, a wing-tip body, wing fences, wing trailing-edge flaps, horizontal-tail settings, and wing dihedral angle. The investigation covered the Mach number range from 0.20 to 1.03 for the angle-of-attack range from -5 degrees to 15.4 degrees, and a sideslip angle of -5 degrees, in the Reynolds number range from 0.52 times 10(exp 6) to 1.94 times 10(exp 6) based on the wing mean aerodynamic chord. The various fuselage and wing additions delayed the drag-rise Mach number and greatly reduced the drag beyond the drag rise. The wing bodies markedly alleviated unstable pitch tendencies throughout the test Mach number range. At low landing speeds, the wing bodies exhibited little interference with the ability of trailing-edge flaps to increase the lift near maximum lift coefficient; and the use of fences greatly reduced the severe longitudinal instability trend at landing attitudes. The model with a 6 degree dihedral angle exhibited positive lateral and directional stability characteristics in the presence of the fuselage and wing additions. An increase in drag-rise Mach number associated with the fuselage and wing additions on the 40 degree sweptback wing combination was similar to that for the comparable 45 degree combination. These additions did, however, reduce the drag of the 40 degree sweptback configurations more than the 45 degree configurations in the transonic speed range.

Loving, Donald L.↗

NASA NTRS1973

Heat transfer phase change paint test (OH-42) of a Rockwell International SSV orbiter in the NASA/LRC Mach 8 variable density wind tunnel

Phase change paint tests of a Rockwell International .00593-scale space shuttle orbiter were conducted in the Langley Research Center's Variable Density Wind Tunnel. The test objectives were to determine the effects of various wing/underbody configurations on the aerodynamic heating rates and boundary layer transition during simulated entry conditions. Several models were constructed. Each varied from the other in either wing cuff radius, airfoil thickness, or wing-fuselage underbody blending. Two ventral fins were glued to the fuselage underside of one model to test the interference heating effects. Simulated Mach 8 entry data were obtained for each configuration at angles of attack ranging from 25 to 40 deg, and a Reynolds number variation of one million to eight million. Elevon, bodyflap, and rudder flare deflections were tested. Oil flow visualization and Schlieren photographs were obtained to aid in reducing the phase change paint data as well as to observe the flow patterns peculiar to each configuration.

Jones, R.↗

NASA NTRS1977

Self streamlining wind tunnel: Low speed testing and transonic test section design

Comprehensive aerodynamic data on an airfoil section were obtained through a wide range of angles of attack, both stalled and unstalled. Data were gathered using a self streamlining wind tunnel and were compared to results obtained on the same section in a conventional wind tunnel. The reduction of wall interference through streamline was demonstrated.

Wolf, S. W. D.↗

NASA NTRS1956

Supersonic flow past nonlifting bumped and indented bodies of revolution

Linear-theory values of the supersonic pressure field and wave drag of nonlifting bumped and indented bodies of revolution are presented and compared with the corresponding properties of a smooth body. The comparisons indicate that relatively small surface irregularities cause large pressure disturbances and changes in wave drag. The interference drag produced by bumps and indentations is discussed and a correction for the curvature of the characteristics is applied.

FLOW, SUPERSONIC↗

NASA NTRS1976

Some recent developments in the aerodynamics of wings for high speeds

The items discussed are: (1) a recently proposed correction formula for the effect of compressibility in two dimensional subsonic flow; (2) the equivalence rule and the area rule for transonic speeds; (3) reciprocal relations in linearized wing theory; and (4) some general results connected with the problem of minimum wave resistance. The paper concludes with an example showing indentation of the fuselage to obtain favorable interference with the wing at supersonic speeds.

Jones, R. T.↗

NASA NTRS1981

The NTF as a national facility

The future evolution of the NTF as a national facility was discussed. The aerodynamic test facility is charged with maintaining the test data and operating the facility with maximum productivity to increase the utility as well as to minimize the test costs. Efforts are under way to increase productivity of the wind tunnels. The future developments needed include: (1) the elimination of wall interference uncertainties; (2) the elimination of minimization of sting interference; and (3) the achievement of free air quality low turbulence airflow. Research in the wall interference area, smart walls, is reported.

Brown, C. E.↗

NASA NTRS1989

Coupled fluid-thermal-structural analysis for aerodynamically heated structures

A finite element approach for integrated fluid-thermal-structural analysis of aerodynamically heated structures is described. The approach is used to solve: (1) the Navier-Stokes equations for the aerodynamic flow, (2) the energy equation of the structure for the temperature response, and (3) the quasi-static equilibrium equations of the structure for the structural response. Coupling between the three disciplines is demonstrated using two applications: Mach 7 flow over a panel and Mach 8 shock-shock interference on a cylinder.

Dechaumphai, Pramote↗

NASA NTRS1990

Supersonic aircraft drag reduction

This paper reviews aerodynamic drag reduction for friction, wave and vortex drag associated with supersonic cruise aircraft and suggests approaches and research directions. Suction laminar flow control may also enable improved low-speed, high-lift systems, improved lift-to-drag ratio for subsonic cruise, reduced parasitic viscous drag for favorable interference wave drag reduction approaches, and turbulent skin friction reduction via slot injection. Flow separation control at cruise proffers opportunities for increased leading-edge thrust, increased lift increment from upper surface, increased fuselage lift/camber for wave drag-due-to-lift reduction, improved performance of various favorable interference wave drag reduction schemes, as well as possibly better low-speed, high-lift systems and wing cruise performance.

Bushnell, D. M.↗