Search NASA⌕ Search

SEARCH · Search NASA

Results for “Assist”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Microstructure and Mechanical Properties of the AA7075 Tube Fabricated using Shear Assisted Processing and Extrusion (ShAPE)

Shear Assisted Processing and Extrusion (ShAPE) experimental setup and tooling were adopted for extruding thin-walled AA7075 aluminum tube from as-cast non-homogenized billet material in a single run. The mechanical and microstructural characterizations were performed on the extrudate in the as-extruded condition without subsequent heat treating. It was shown that the ShAPE process developed a significantly refined microstructure with uniform and almost equiaxed grain structure on both hoop and axial cross-sections of the extrudate as well as through the thickness of the material. The pole figures and inverse pole figures of the EBSD data showed an strong shear texture development, and it was found out that axial shear is the dominant deformation mechanism in the regions near the inner surface of the tube, while combined axial and torsional shears are the two dominant modes of deformation near the outer surface of the extrudate. As for the mechanical properties, there was an increase of 150% and 73% in the yield and ultimate strengths of the tube produced using ShAPE process, respectively, and a 18% decrease in maximum uniform plastic elongation compared to the conventionally extruded AA7075-O tube.

Shear Assisted Processing and Extrusion, Friction ↗
DOE OSTI2020

Enhanced visible-light-assisted peroxymonosulfate activation on cobalt-doped mesoporous iron oxide for orange II degradation

Sulfate radical-based advanced oxidation processes (SR-AOP) attracted a lot of attention due to their capability and adaptability in wastewater treatment. Although heterogeneous cobalt-based catalysts have been extensively studied and have emerged superior for peroxymonosulfate (PMS) activation, leaching of cobalt is still a major concern. Herein, we report a photo-assisted PMS activation approach using cobalt doped mesoporous iron oxide with exceptional activity and stability up to 7 cycles with very low cobalt leaching (0.5 ppm). The highest activity was obtained by 1 mol % cobalt doped mesoporous iron oxide. Orange II dye was completely degraded by the reactive oxygen species (ROS) generated under visible light irradiation within 1 min. ROS were evaluated using two distinct techniques (Fluorescence probes and Electron Paramagnetic Resonance (EPR). ROS quenching experiments were also used to highlight the dominant pathway. This study correlates the structural and electronic changes induced with cobalt doping to the exceptional activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Assessing thermal resilience of an assisted living facility during heat waves and cold snaps with power outages

Extreme hot and cold weather events are becoming more frequent, intense, and longer due to climate change. When these events occur coincidentally with power outages, the resulting extreme indoor temperatures pose a severe health hazard for occupants. This study conducted a holistic modeling and analysis of an assisted living facility, where senior residents live, to assess its thermal resilience performance under a six-day heat wave in 2015 and a three-day cold snap in 2021 with power outages. Impacts of 13 energy efficiency measures on thermal resilience and backup power capacity of the facility were evaluated. Three thermal resilience metrics: the SET (standard effective temperature) degree-hours, the Heat Index, and the Hours of Safety, were used and calculated from the EnergyPlus simulation models. Furthermore, major findings are: (1) the facility would suffer from extreme temperatures during the cold and hot events without a power supply, not meeting the passive survivability requirements; (2) most passive envelope measures improve thermal resilience for both hot and cold events, but making the building envelope airtight results in conflicting performance between the hot and cold events; (3) natural ventilation is an effective measure to mitigate summer indoor overheating; and (4) the energy efficiency package can reduce backup power capacity by 19% for the three-day cold snap. It is recommended that building technologies and design strategies be evaluated to consider co-benefits of energy use, thermal resilience, and backup power needs through building energy codes or policies for existing and new buildings, which are transitioning for decarbonization and climate resilience.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Electrical and structural characterization of nano-carbon–aluminum composites fabricated by electro-charging-assisted process

Incorporating nano-carbon phases into metal-matrix composites is a promising strategy for simultaneously enhancing electrical conductivity and mechanical properties of metals. Here, we describe the manufacture of novel nano-carbonaluminum composites by an electro-charge-assisted process (EAP) that show 5.6% ± 1.7% increase in electrical conductivity compared to the base metal alloy. The source of nano-carbon that we used in this study is activated carbon with particle size less than 100 nm. The enhancement is attributed to nano-graphitic structures that extend through the lattice of the metal. Through electron transfer from the metal to the nanostructures the electron density at the interface of nano-crystalline graphite and the metal lattice increases thereby enhancing the bulk electrical conductivity. We identify the important fabrication parameters of the EAP for a reaction system employing a tapered graphite cathode. Here, a high current density of 100 A/cm 2 causes ionization and crystallization of the carbon in the liquid metal. The increase in electrical conductivity of the composite are directly related to the incorporation of the nanocrystalline carbon in the metal lattice. The superior performance of these nano-carbon aluminum composites makes them promising candidates for power transmission lines and other applications.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2026

A Generalized Grain-Scale Model for the Non-Plasma and Plasma-Assisted Hydrogen Direct Reduction of Iron Ore

Direct Reduction of Iron ore using hydrogen (H-DRI) is a promising pathway towards efficient steelmaking and accurate predictive models are a necessity for scale-up and optimization of this technology. However, accurate models of this process remain limited because existing models oversimplify grain-scale phenomena, such as nonlinearity inside grain, self-sufficient porosity, surface reactions, and the role of plasma species. These phenomena are important for flash steelmaking and plasma-assisted H-DRI processes. To address this need, we present a phenomenological model for simulating H-DRI at the scale of a single micron-sized grain of the iron ore. We call this the Transient Reactive Grain Model (TRGM). TRGM incorporates key physical process: gas species transport, a chemical kinetics of material conversion, nanopore structural evolution and, adsorption-desorption surface kinetics at the reactive nanopore surface. The important contribution of this work is that the model provides a dependence on different reductant species, specifically hydrogen atoms versus molecules, so that role of hydrogen plasma reduction can be clarified compared to the use of pure hydrogen gas reduction. TRGM predictions agree well with experimental data for both molecular H2 reduction of Fe2O3 and plasma hydrogen reduction of Fe3O4. Results reveal species concentration gradients with a diffuse reaction zone, and enhanced hydrogen diffusion at the grain outer surface due to evolving porosity. These findings challenge common assumptions in existing models, including sharp reaction fronts, quasi-steady diffusion and kinetics, and the neglect of surface chemistry. As a generalized grain-scale model for H-DRI processes, TRGM has practical applications in flash steelmaking and in-flight reduction using both molecular and plasma hydrogen.

08 HYDROGEN↗
DOE OSTI2022

Effect of various post-extrusion tempering on performance of AA2024 tubes fabricated by shear assisted processing and extrusion

In this report aluminum alloy 2024 (AA2024) tubes were extruded using the shear assisted processing and extrusion (ShAPE) method. As a ubiquitous aerospace alloy, AA2024 has reached a high degree of maturity with respect to manufacturing processes, alloy chemistry and heat treatment to maximize material strength. Therefore, over the eight decades since the introduction of this alloy, the mechanical properties have plateaued, and the extrusion speed has reached a 3.5 m/min ceiling using conventional extrusion. The ShAPE technique enabled an extrusion speed of AA2024 up to 7.4 m/min at 480 °C which is surpassing the extrudability chart of this alloy. Variation of the standard T3510 and T8510 post extrusion heat treatments were applied to improve the mechanical performance of the ShAPE extruded AA2024 tube. The ultimate tensile strength and yield strength of AA2024-T8510 ShAPE extruded tube are 522.0 ± 3.3 MPa and 510.7 ± 3.3 MPa, which are respectively 18% and 32% higher than ASM-typical and ASTM minimum values. The elongation at break of ShAPE extruded AA2024-T8510 tubes is two times higher than the ASM-typical and ASTM-minimum values. This improved ductility is attributed to the refinement of grain size and secondary phases as well as due to the uniform dispersion of sub-micron strengthening precipitates formed during the ShAPE process.

42 ENGINEERING↗
DOE OSTI2023

Ground vehicle lane-keeping assistance system via differential flatness output feedback control and algebraic derivative estimation

Vehicle run-off-road is one of the most frequent and fatal traffic accidents in the United States. Various lane-keeping assistance (LKA) systems have been developed in the last decade to help drivers stay on the road. Most of them are built upon linear driver–vehicle–road (DVR) models and treat road curvature as a disturbance. Albeit effective, their control performance would degrade if road curvature varies rapidly. Here, this paper proposes a novel nonlinear DVR model by integrating a driver steering model into vehicle–road kinematics, which explicitly considers road curvature. Particularly, this nonlinear DVR system has been proven to be differentially flat, and a flatness-based LKA system is designed. Additionally, Model-Free Control is introduced to compensate for system modeling errors. Hardware-in-the-loop simulations and diver-in-the-loop experiments validate the proposed control framework and demonstrate the performance enhancement with respect to a representative linear robust LKA system.

42 ENGINEERING↗
DOE OSTI2022

Comparative techno-economic assessment of osmotically-assisted reverse osmosis and batch-operated vacuum-air-gap membrane distillation for high-salinity water desalination

New developments in pressure- and thermally driven membrane desalination technologies offer the potential to cost-effectively treat high-salinity waters, especially when powered by low-cost solar electricity and thermal energy. This paper presents a comparative techno-economic assessment of the state-of-the-art most promising pressure- and thermally driven membrane technologies for high recovery desalination, namely, osmotically-assisted reverse osmosis (OARO) and batch-operated vacuum-air-gap membrane distillation (batch V-AGMD), to produce potable water while concentrating brine within the range of 140–290 g/L TDS for minimum-liquid-discharge (MLD) and zero-liquid-discharge (ZLD) applications. It is shown that both OARO and batch V-AGMD can treat feedwater and brines with TDS in the range of 30–125 g/L with corresponding fresh water recovery rates of 85–25%. When low cost solar electricity and thermal energy are used, the resulting levelized cost of water (LCOW) from OARO is in the range of 0.70–6.28 $/m 3 , and that from batch-V-AGMD is in the range of 1.74–2.77 $/m 3 . OARO is more cost-effective than batch V-AGMD when feedwater salinity is below 70 g/L and recovery below 75%, whereas batch V-AGMD is more cost-effective at higher recovery rates and salinity levels. Finally, the sensitivity of this comparison on energy prices and module costs is discussed.

42 ENGINEERING↗
DOE OSTI2022

Optimization-based modeling and analysis of brine reflux osmotically assisted reverse osmosis for application toward zero liquid discharge systems

Significant amounts of high-salinity wastewater generated by water-intensive industrial activities such as shale oil and gas production have raised serious environmental concerns in recent years. Existing and emerging desalination technologies offer promise to manage these high salinity wastewater streams while simultaneously producing fresh water that could be diverted for beneficial uses. Osmotically assisted reverse osmosis (OARO) is one such emerging desalination technology capable of handling hypersaline brines and achieving high recoveries. However, rigorous modeling and analysis is needed to evaluate the process performance, energy consumption, and treatment cost of various OARO configurations. Here, this work presents detailed modeling and analysis of brine-reflux OARO (BR-OARO) system and compares it with other commonly discussed configurations, including cascading osmotically mediated reverse osmosis (COMRO), consecutive loop OARO, and split feed counterflow RO, through a cost optimization-based framework. We analyze and compare the treatment costs, membrane area, specific energy consumption, and design parameters of the aforementioned configurations with the ultimate goal of achieving zero liquid discharge (ZLD). The results indicate that the BR-OARO system with treatment cost of 5.1 US $/m 3 of produced water with 10% salinity outperforms other configurations in terms of number of stages needed, treatment cost, membrane area, and energy consumption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Investigation of startup, performance and cycling of a residential furnace integrated with micro-tubular flame-assisted fuel cells for micro-combined heat and power

Solid Oxide Fuel Cells (SOFCs) offer advantages for micro-Combined Heat and Power (μCHP), but currently suffer from slow startup (>1 h) and limited thermal cycling which reduces the applications, energy savings and economics. In this work, a micro-Tubular SOFC stack is integrated into a residential furnace to create a micro-Tubular Flame-assisted Fuel Cell (mT-FFC) μCHP system. A high power density of 202 mW cm -2 is reported operating in synthesis gas generated from fuel-rich combustion of natural gas/air. Unlike previous reports, instabilities in the polarization are attributed to low temperature of the oxygen reduction reaction at the cathode. The mT-FFC stack achieved peak power density in 6 min after ignition. 200 thermal cycles at an average heating rate of 215 °C.min -1 and average cooling rate of 176 °C.min -1 were conducted and a low degradation rate of 0.0325 V per 100 cycles per fuel cell was achieved. Low NO x emissions (10 ppm) and high combined efficiency is reported.

25 ENERGY STORAGE↗
DOE OSTI2020

Techno-economic analysis of cathode material production using flame-assisted spray pyrolysis

The cost of cathode materials contributes approximately 32.7% of the total cell construction cost of lithium-ion batteries, significantly affecting the price of battery packs. To reduce the cathode material manufacturing cost, a flame-assisted spray pyrolysis (FSP) method has been developed to utilize a sustainable solvent of glycerol to manufacture the LiNi 1/3 Mn 1/3 Co 1/3 O 2 (NMC333) cathode materials. The purpose of this study is to evaluate the minimum cathode material selling price (MCSP) of the FSP processes compared with a traditional carbonate co-precipitation pathway. Results show that the MCSP of the FSP is $\$$19.1/kg that is 17% lower than the traditional carbonate co-precipitation pathway as a result of lower fixed operating cost and variable overhead. Sensitivity analysis shows that when the new process is integrated with in-situ sintering and processing, the MCSP can be as low as $\$$15.6/kg. When all the material prices are decreased by 20%, the FSP process can synthesize NMC333 at a price of $\$$2.3/kg lower. According to the simulation result, LiNi 0·8 Mn 0·1 Co 0·1 O 2 (NMC811) has the best potential to meet the U.S. Department of Energy battery price target of $\$$125/kWh, demonstrating that the FSP process is an attractive manufacturing technology for NMC cathode powder material production.

25 ENERGY STORAGE↗
DOE OSTI2020

Electric current–assisted direct joining of silicon carbide

Conventional direct joining technologies are difficult to use with silicon carbide (SiC) materials, especially for fiber composite forms of SiC, because of the harsh conditions required. Therefore, to reduce the temperature and/or process time required for the direct joining process, an electric current–assisted joining (ECAJ) method was studied. Joining of low–resistivity grade, nitrogen doped β-SiC was demonstrated at a relatively low nominal temperature of 1750 °C with a 10 min hold by enhancing the passage of current through the material. The joining mechanism is discussed in terms of localized overheating and accelerated self-diffusion at the interface. In the case of joining at 2160 °C for 1 min, rapid crystal growth of textured SiC was found at the interface. This study indicates that rapid ECAJ-based direct joining is a practical and appropriate method for joining SiC-based materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High speed manufacturing of aluminum alloy 7075 tubing by Shear Assisted Processing and Extrusion (ShAPE)

Shear assisted processing and extrusion (ShAPE) was used to extrude aluminum alloy 7075 tubing at speeds up to 12.2 m/min. This is in comparison to 2.0 m/min which is generally the limit for conventionally extruded 7075. The increased speed is primarily attributed to more extensive shear deformation, compared to conventional extrusion, which results in a high density of low angle grain boundaries that facilitate continued deformation and delay the onset of surface tearing. Mechanical testing after heat treating to the T6 condition gave an ultimate tensile strength of 565.3 ± 4.6 MPa, yield strength of 495.7 ± 8.7 MPa, and elongation of 16.8 ± 0.8%. Strength values exceed the ASTM minimum standard and are on par with ASM typical values, while elongation was substantially improved compared to 7 and 11% for the ASTM and ASM values respectively. Finally, it was observed that low temperature extrusion at 341 °C and 40 rpm gave superior material properties in the T6 condition compared to high temperature extrusion at 441 °C and 120 rpm due to variances in nanoscale second phase size and distribution.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Selective laser melting of oxide dispersion strengthened MA956 alloy and its surface finishing by magnetic field assisted finishing

Selective laser melting (SLM) is a prominent metal additive manufacturing (AM) capable of processing a myriad of engineering materials with high precision and design freedom. However, similar to other AM processes, poor surface finishing has been an omnipresent problem in SLM technology. In this study, magnetic field assisted finishing (MAF) was used to finish SLM fabricated oxide dispersion strengthened (ODS) MA956, an iron-chromium-aluminum alloy. The effect of laser processing parameters on part density and surface roughness was first studied. Using a multi-objective optimization technique, the optimal parameters to obtain the highest density and lowest surface roughness were determined. Finally, MAF was applied to the parts built with the obtained optimal SLM parameters, but without significant improvement on the surfaces of as-printed samples. Hence, the surfaces of as-printed samples were post-processed (ground) to yield better initial surface conditions prior to MAF. The effect of initial roughness, iron particles size, and abrasive size on MAF performance was studied. Initial roughness had the most dominant effect followed by abrasive size. The underlying mechanism behind the dependency on initial roughness on final surface quality was analyzed by studying the change on the surface profiles with different starting initial roughness. The initial roughness required for MAF to be effective was determined. In conclusion, using the optimal processing conditions, MAF was applied to the post-processed samples to attain the final average surface roughness (R a ) as little as 0.36 μm starting from initial average roughness (R a ) of 1.53 μm.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhanced diffusion bonding of alloy 617 using electric field-assisted sintering

The development of compact heat exchangers (CHXs) has gained increasing interest in many industries owing to their high thermal efficiency and reduced size. Diffusion bonding (DB) is an advantageous technique for fabricating CHXs. Alloy 617 is a candidate for manufacturing CHXs for high-temperature advanced nuclear reactors due to its elevated-temperature properties. Previous endeavors in DB of Alloy 617 were conducted by hot pressing (HP), which reported precipitates at the diffusion-bond interface, limited grain boundary (GB) migration, and significantly reduced high-temperature mechanical properties. To overcome these challenges, this study investigated DB of Alloy 617 using electric field-assisted sintering (EFAS). Stacks composed of three sheets were bonded with EFAS using different temperatures, pressures, and hold times. DB using HP as the zero-current analog of EFAS was also performed for comparison. The result shows that Cr- and Mo-rich precipitates were formed at the interface of the hot-pressed samples. The electric current and temperature in EFAS play a significant role in precipitation and GB migration. The electric current coupled with correct temperatures can effectively prevent precipitate formation at the interface and achieve excellent GB migration. Nanoscale Al-rich oxide was formed at the interface of the samples made by both HP and EFAS, but grain boundaries can ignore the nanoscale Al-oxide and migrate across the interface. The temperature, pressure, and hold time also affected diffusion. The temperature is a prerequisite for a successful GB migration, and GB migration can be enhanced by increasing pressure and hold time.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Fabrication of thin-walled tubes from alloy 602 CA using shear assisted processing and extrusion

Thin-walled tube is usually produced seamlessly via an expensive multi-step process or via welding of thin sheets but at reduced performance. To overcome the current process and performance inefficiencies, advanced manufacturing methods need to be investigated. In this investigation, shear assisted processing and extrusion (ShAPE) was used to fabricate thin-walled Inconel 602 tube in a single-step. Tubes measuring 0.83 m length with a 12 mm outer diameter and 1 mm wall thickness were fabricated with an average surface roughness, Ra of 1.6 µm and Rz of 15 µm. Tensile testing of tubes in the as-fabricated condition showed strength increases of 4-35% over current offerings while maintaining or improving elongation. Electron microscopy analysis revealed the recrystallized microstructure with refined inter- and intra-granular carbides. Preliminary results obtained in this investigation shows the feasibility of producing thin-wall high temperature tube in single-step via ShAPE. This achievement marks a significant step towards manufacturing larger diameter nickel alloy tubes for the U.S. Department of Energy’s Waste Treatment and Immobilization Plant.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High performance porous Si anode enabled by an organic-solvent assisted etching process

Silicon (Si) is a promising anode for the next generation of lithium-ion batteries, but its large volume changes (~300 %) during cycling hindered its practical applications. One method to improve its stability is to etch micron sized Si/SiO 2 particles to form porous Si (p-Si) and accommodate volume changes internally. However, the conventional HF etching method generates excess gas/heat and is difficult to scale up. Herein, we developed an organic-solvent-assisted HF etching process (O-HF) using a mixture of benzene and saturated HF aqueous solution. The organic solvent can be preferentially absorbed on the surface of Si/SiO 2 powder so etching rate of SiO 2 can be controlled to avoid rapid gas/heat generation. This method can also prevent over-etching of Si by minimizing direct contact/react between water and newly exposed Si. Si||NMC622 cells using carbon coated p-Si particles prepared by optimized O-HF etching process demonstrate a capacity retention of 82.0 % after 500 cycles, which is much better than those prepared by conventional HF etching (73.7 %). The thickness of Si anode increases only ~10 % during the initial lithiation, which is comparable with those of graphite anode. In conclusion, the O-HF etching strategy developed in this work can also be applied to the etching of a broad range of materials.

HF etching↗
DOE OSTI2020

Effect of Co 2 N impurity on the superconducting properties of δ-MoN thin films grown by polymer assisted deposition

We report the effect of Co 2 N impurity on the superconducting properties of δ-MoN thin films grown by polymer-assisted deposition on c-cut sapphire (Al 2 O 3 ). The films show a superconducting transition temperature of 10.4 K and an upper critical field H c2 (0) perpendicular to the film surface around 3 T. The latter corresponds to a relatively large coherence length ξ, which enhances the two-dimensional limit when the magnetic field is applied parallel to the film surface. In comparison with pure δ-MoN films, the inclusion of Co 2 N impurity in the δ-MoN films could significantly modify the critical current density at the vortex-free state. In conclusion, the ability to tune the superconducting properties of metal-nitride superconductors by introducing chemically and structurally compatible impurity may find potential applications for superconducting single-photon detectors.

36 MATERIALS SCIENCE↗