SEARCH · Search NASA

Results for “Bandwidth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1984

Coherent Digital Demodulation of a Residual Carrier Signal Using IF Sampling

An analysis is presented of a digital technique for the coherent demodulation of a residual carrier signal with a biphase modulated square wave subcarrier. The processing technique employs the concept of intermediate frequencies IF sampling. An optimum Costas loop is used for subcarrier demodulation and data-aided carrier tracking, i.e., combined Costas and residual carrier tracking. It is shown that the loops perform essentially the same as the corresponding analog loops in terms of signal-to-noise ratio and loop bandwidth. The sampling does not introduce biases or other significant effects on the loops, provided that the loop bandwidth is very small compared to the symbol rate, and that the number of samples per symbol is large compared to inverse loop bandwidth.

Sfeir, R.↗

NASA NTRS1985

A sequential decoding performance analysis for International Comet Explorer

The effect of a noisy reference carrier on the performance of International Comet Explorer (ICE) Sequential decoder is analyzed. Ideal reference models for frame deletion probability are given for the Telemetry Processing Assembly (TPA) and the Linkabit (LS4815) sequential decoders. Based on these ideal reference models the deletion probability in the presence of noisy reference carrier is computed for both the high and the low data rate cases. A medium data rate performance model is then derived using an interpolation method. The derived medium rate performance model depends on the phase locked loop bandwidth-integration time product. Results are obtained for frame length 1024 bits, data bit rates of 1024 bps and 512 bps, modulation index of 60 deg, and threshold loop bandwidths of 10 Hz and 3 Hz. The medium rate model agrees with experimental data to within measurement uncertainty. For the 10 Hz loop bandwidth and modulation index of 60 deg at frame deletion rate of 0.0001, the required total received power to noise ratio is 36 dB. The analysis given is general and applicable to any sequential decoder, provided that the ideal reference model of the decoder is available.

Divsalar, D.↗

NASA NTRS1986

EOS radiometer concepts for soil moisture remote sensing

Preliminary work with aperture synthesis concepts for EOS is reported. The effects of nonvanishing bandwidths on image reconstruction in aperture synthesis system was studied. It is found that nonvanishing bandwidths introduce errors in off-axis pixels when naive Fourier processing is used. The net effect is for bandwidth to limit sensor field-of-view. To quantify this effect a computer program was written which is documented. Example runs are included which illustrate the resultant radiometric errors and effective fields-of-view for a plausible simple sensor.

Carr, J.↗

NASA NTRS1985

Fine pointing of the Solar Optical Telescope in the Space Shuttle environment

Instruments requiring fine (i.e., sub-arcsecond) pointing, such as the Solar Optical Telescope (SOT), must be equipped with two-stage pointing devices, coarse and fine. Coarse pointing will be performed by a gimbal system, such as the Instrument Pointing System, while the image motion compensation (IMC) will provide fine pointing. This paper describes work performed on the SOT concept design that illustrates IMC as applied to SOT. The SOT control system was modeled in the frequency domain to evaluate performance, stability, and bandwidth requirements. The two requirements of the pointing control, i.e., the 2 arcsecond reproducibility and 0.03 arcsecond rms pointing jitter, can be satisfied by use of IMC at about 20 Hz bandwidth. The need for this high bandwidth is related to Shuttle-induced disturbances that arise primarily from man push-offs and vernier thruster firings. A block diagram of SOT model/stability analysis, schematic illustrations of the SOT pointing system, and a structural model summary are included.

Gowrinathan, S.↗

NASA NTRS1986

Review of measurements of the RF spectrum of radiation from lightning

A review is presented of the measurements reported in the literature of the spectrum of electromagnetic radiation from lightning in the frequency range from 1 kHz to 1 GHz. Measurements have been made either by monitoring the power received at individual frequencies using a narrow bandwidth recording device tuned to the frequencies under investigation or by recording the transient (time dependent) radiation with a wide bandwidth device and then Fourier transforming the waveform to obtain a spectrum. Measurements of the first type were made extensively in the 1950’s and 1960’s and several composite spectra have been deduced by normalizing the data of different investigators to common units of bandwidth and distance. The composite spectra tend to peak near 5 kHz and then decrease roughly as (frequency).’ upto nearly 100 MHz where scatter in the data make the behaviour uncertain. Measurements of the second type have been reported for return strokes, the stepped leader and for some intracloud processes. The spectrum of first return strokes obtained in this manner is very similar to the composite spectra obtained from the narrowband measurements.

Lightning Spectrum↗

NASA NTRS1987

Error control techniques for satellite and space communications

During the period June 1, 1986 through November 30, 1986, progress was made in the following areas: undetected error probability and throughput analysis of a concatenated coding scheme; capacity and cutoff rate analysis of concatenated codes; concatenated codes using bandwidth efficient trellis inner codes; bounds on the minimum free Euclidean distance of bandwidth efficient trellis codes; and construction of multidimensional bandwidth efficient trellis codes for use as inner codes in a concatenated coding system.

Costello, Daniel J., Jr.↗

NASA NTRS1987

Channel access schemes and fiber optic configurations for integrated-services local area networks

Local Area Networks are in common use for data communications and have enjoyed great success. Recently, there is a growing interest in using a single network to support many applications in addition to traditional data traffic. These additional applications introduce new requirements in terms of volume of traffic and real-time delivery of data which are not met by existing networks. To satisfy these requirements, a high-bandwidth tranmission medium, such as fiber optics, and a distributed channel access scheme for the efficient sharing of the bandwidth among the various applications are needed. As far as the throughput-delay requirements of the various application are concerned, a network structure along with a distributed channel access are proposed which incorporate appropriate scheduling policies for the transmission of outstanding messages on the network. A dynamic scheduling policy was devised which outperforms all existing policies in terms of minimizing the expected cost per message. A broadcast mechanism was devised for the efficient dissemination of all relevant information. Fiber optic technology is considered for the high-bandwidth transmisison medium.

Nassehi, M. Mehdi↗

NASA NTRS1986

Optical fiber sensors for the non-destructive evaluation of materials

The operation of the modal domain vibration sensor was demonstrated in several simple vibrational systems. Two apparent advantages are the sensors bandwidth and sensitivity. An inherent drawback of standard vibration detection devices is their rapid cost increase with high frequency bandwidth. This sensor showed consistent response in the freqency range of 1.5 to 400 Hz. By imparting very small but measurable excitations in the structures, the sensors ability to respond to very low order vibration induced strain was established. Dynamic ranges on the order of 18 to 22 dB for the CF beam and string systems respectively were observed. The sensor itself represents a very simple system: a coherent source, a single fiber and a low bandwidth detector. The inherent advantages of ruggedness and immunity to external radiation can also be added. Finally, the sensor minimally impairs structural motion through loading, an advantage in monitoring small vibrations or lightweight structures. Some drawbacks of the sensor are also noted.

Source record↗

NASA NTRS1987

Electron cyclotron harmonic wave acceleration

A nonlinear analysis of particle acceleration in a finite bandwidth, obliquely propagating electromagnetic cyclotron wave is presented. It has been suggested by Sprangle and Vlahos in 1983 that the narrow bandwidth cyclotron radiation emitted by the unstable electron distribution inside a flaring solar loop can accelerate electrons outside the loop by the interaction of a monochromatic wave propagating along the ambient magnetic field with the ambient electrons. It is shown here that electrons gyrating and streaming along a uniform, static magnetic field can be accelerated by interacting with the fundamental or second harmonic of a monochromatic, obliquely propagating cyclotron wave. It is also shown that the acceleration is virtually unchanged when a wave with finite bandwidth is considered. This acceleration mechanism can explain the observed high-energy electrons in type III bursts.

Karimabadi, H.↗

NASA NTRS1987

A flight investigation of helicopter low-speed response requirements

A flight experiment has been conducted using the Canadian National Aeronautical Establishment's variable-stability airborne simulator to define the dynamic response requirements for operations at hover and low speeds. Fourteen Attitude Command/Attitude Hold, Rate, and Rate Command/Attitude Hold configurations were evaluated by six pilots using both conventional controls and a four-axis integrated sidestick over a low-speed course consisting of precision hover, landing, sidestep, and dash/quickstop tasks. The results indicate that with conventional controls all three response-types were acceptable as long as their response bandwidth was sufficiently high, and higher bandwidths were required in roll than in pitch. With the four-axis sidestick, there was a preference for the Rate systems. The range of acceptable bandwidths was lower, and the spread in pilot ratings smaller, than were found in a similar ground-based simulation.

Mitchell, David G.↗

NASA NTRS1987

Detection of signals by the digital integrate-and-dump filter with offset sampling

The Integrate and Dump Filter (IDF) is used as a matched filter for the detection of signals in additive white Gaussian noise. The performance of the digital integrate and dump filter is evaluated. The case considered is when symbol times are known and the sampling clock is free running at a constant rate, i.e., the sampling clock is not phase locked to the symbol clock. Degradations in the output signal to noise ratio of the digital implementation due to sampling rate, sampling offset, and finite bandwidth, resulting from the anti-aliasing low pass prefilter, are computed and compared with those of the analog counterpart. It is shown that the digital IDF performs within 0.6 dB of the ideal analog IDF whenever the prefilter bandwidth exceeds four times the symbol rate and when sampling is performed at the Nyquist rate. The loss can be reduced to 0.3 dB by doubling the sampling rate, where 0.2 dB loss results from finite bandwidth and 0.1 dB results from the digital IDF.

Sadr, R.↗

NASA NTRS1988

Transport delay compensation for computer-generated imagery systems

In the problem of pure transport delay in a low-pass system, a trade-off exists with respect to performance within and beyond a frequency bandwidth. When activity beyond the band is attenuated because of other considerations, this trade-off may be used to improve the performance within the band. Specifically, transport delay in computer-generated imagery systems is reduced to a manageable problem by recognizing frequency limits in vehicle activity and manual-control capacity. Based on these limits, a compensation algorithm has been developed for use in aircraft simulation at NASA Ames Research Center. For direct measurement of transport delays, a beam-splitter experiment is presented that accounts for the complete flight simulation environment. Values determined by this experiment are appropriate for use in the compensation algorithm. The algorithm extends the bandwidth of high-frequency flight simulation to well beyond that of normal pilot inputs. Within this bandwidth, the visual scene presentation manifests negligible gain distortion and phase lag. After a year of utilization, two minor exceptions to universal simulation applicability have been identified and subsequently resolved.

Mcfarland, Richard E.↗

NASA NTRS1988

Error control techniques for satellite and space communications

During the period December 1, 1987 through May 31, 1988, progress was made in the following areas: construction of Multi-Dimensional Bandwidth Efficient Trellis Codes with MPSK modulation; performance analysis of Bandwidth Efficient Trellis Coded Modulation schemes; and performance analysis of Bandwidth Efficient Trellis Codes on Fading Channels.

Costello, Daniel J., Jr.↗

NASA NTRS1988

Two-Dimensional Sequential and Concurrent Finite Element Analysis of Unstiffened and Stiffened Aluminum and Composite Panels with Hole

The results of a detailed investigation of the distribution of stresses in aluminum and composite panels subjected to uniform end shortening are presented. The focus problem is a rectangular panel with two longitudinal stiffeners, and an inner stiffener discontinuous at a central hole in the panel. The influence of the stiffeners on the stresses is evaluated through a two-dimensional global finite element analysis in the absence or presence of the hole. Contrary to the physical feel, it is found that the maximum stresses from the glocal analysis for both stiffened aluminum and composite panels are greater than the corresponding stresses for the unstiffened panels. The inner discontinuous stiffener causes a greater increase in stresses than the reduction provided by the two outer stiffeners. A detailed layer-by-layer study of stresses around the hole is also presented for both unstiffened and stiffened composite panels. A parallel equation solver is used for the global system of equations since the computational time is far less than that using a sequential scheme. A parallel Choleski method with up to 16 processors is used on Flex/32 Multicomputer at NASA Langley Research Center. The parallel computing results are summarized and include the computational times, speedups, bandwidths, and their inter-relationships for the panel problems. It is found that the computational time for the Choleski method decreases with a decrease in bandwidth, and better speedups result as the bandwidth increases.

Razzaq, Zia↗

NASA NTRS1987

Review of measurements of the RF spectrum of radiation from lightning

A review is presented of the measurements reported in the literature of the spectrum of electromagnetic radiation from lightning in the frequency range from 1 kHz to 1 GHz. Measurements have been made either by monitoring the power received at individual frequencies using a narrow bandwidth recording device or by recording the transient (time dependent) radiation with a wide bandwidth device and then Fourier transforming the waveform to obtain a spectrum. Measurements of the first type were made extensively in the 1950's and 1960's and several composite spectra have been deduced by normalizing the data of different investigators to common units of bandwidth and distance. The composite spectra tend to peak near 5 kHz and then decrease roughly as 1/(frequency) up to nearly 100 MHz where scatter in the data make the behaviour uncertain. The spectrum obtained with measurements of the second type is similar. Recent experiments have extended the frequency range covered to several 10's of MHz and include spectra for return strokes, the stepped leader and for some intracloud processes. The spectrum of first return strokes obtained in this manner is very similar to the spectrum of the composite flash obtained from the narrowband measurements.

Radiation↗

NASA NTRS1988

A flexible on-board demultiplexer/demodulator

Optimization of satellite communications system performance from the point of view of reduced overall system cost per unit of service delivered, requires that economies be exercised at all levels. Introduction of onboard regeneration which necessarily involves on-board demultiplexing and demodulation is an essential ingredient in meeting this goal. To achieve maximum benefit from this approach, the uplink transmission data rate and bandwidth from each earth terminal and consequently uplink EIRP needs to be minimized. This necessarily introduces multiple carriers of different bandwidths on the uplinks and creates an attending need onboard for simultaneous demodulation of many carriers. This paper addresses a digitally implemented bulk demultiplexer/demodulator that processes a large number of carriers having differing carrier bandwidths, bit rates and center rrequencies. The device is programmable from the ground to accommodate changes in the complexion of the carriers.

Campanella, S. Joseph↗

NASA NTRS1989

Control-structure interaction in precision pointing servo loops

The control-structure interaction problem is addressed via stability analysis of a generic linear servo loop model. With the plant described by the rigid body mode and a single elastic mode, structural flexibility is categorized into one of three types: (1) appendage, (2) in-the-loop minimum phase, and (3) in-the-loop nonminimum phase. Closing the loop with proportional-derivative (PD) control action and introducing sensor roll-off dynamics in the feedback path, stability conditions are obtained. Trade studies are conducted with modal frequency, modal participation, modal damping, loop bandwidth, and sensor bandwidth treated as free parameters. Results indicate that appendage modes are most likely to produce instability if they are near the sensor rolloff, whereas in-the-loop modes are most dangerous near the loop bandwidth. The main goal of this paper is to provide a fundamental understanding of the control-structure interaction problem so that it may benefit the design of complex spacecraft and pointing system servo loops. In this framework, the JPL Pathfinder gimbal pointer is considered as an example.

Spanos, John T.↗

NASA NTRS1988

Transport delay compensation for computer-generated imagery systems

Mcfarland, Richard E.↗