Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMBUSTION PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Comparative ignition tests of coal under oxy-fuel conditions in a standardized laboratory test rig

Ignitability is important to characterize pulverized coal combustion, as it is directly related to flame stability. The current paper describes a practical test rig for rapid laboratory analysis of pulverized coal cloud ignition properties. The system has been designed for conventional coal combustion conditions using air as the oxidant. In the current work, the measurement principle of the device is described and its adaption to and applicability for oxy-fuel combustion tests is demonstrated. Four coals with different rank were measured in air and in oxy-fuel atmospheres containing 20–35 vol% O 2 in CO 2 . Finally, the major influencing factors for the investigated samples were found to be the coal rank and the gas-phase oxygen concentration, while a minor influence of particle size was observed.

01 COAL, LIGNITE, AND PEAT↗

Large Eddy Simulation of Lean Mixed-Mode Combustion Assisted by Partial Fuel Stratification in a Spark-Ignition Engine

Partial fuel stratification (PFS) is a promising fuel injection strategy to improve the stability of lean combustion by applying a small amount of pilot injection right before spark timing. Mixed-mode combustion, which makes use of end-gas autoignition following conventional deflagration-based combustion, can be further utilized to speed up the overall combustion. In this study, PFS-assisted mixed-mode combustion in a lean-burn direct injection spark-ignition (DISI) engine is numerically investigated using multi-cycle large eddy simulation (LES). A previously developed hybrid G-equation/well-stirred reactor combustion model for the well-mixed operation is extended to the PFS-assisted operation. The experimental spray morphology is employed to derive spray model parameters for the pilot injection. The LES-based model is validated against experimental data and is further compared with the Reynolds-averaged Navier–Stokes (RANS)-based model. Overall, both RANS and LES predict the mean pressure and heat release rate traces well, while LES outperforms RANS in capturing the cycle-to-cycle variation (CCV) and the combustion phasing in the mass burned space. Liquid and vapor penetrations obtained from the simulations agree reasonably well with the experiment. Detailed flame structures predicted from the simulations reveal the transition from a sooting diffusion flame to a lean premixed flame, which is consistent with experimental findings. LES captures more wrinkled and stretched flames than RANS. Finally, the LES model is employed to investigate the impacts of fuel properties, including heat of vaporization (HoV) and laminar burning speed (SL). Combustion phasing is found more sensitive to SL than to HoV, with a larger fuel property sensitivity of the heat release rate from autoignition than that from deflagration. Moreover, the combustion phasing in the PFS-assisted operation is shown to be less sensitive to SL compared with the well-mixed operation.

fuel property sensitivity↗

FY2017 Materials Annual Progress Report

The Materials Technology subprogram supports the Vehicle Technology Office’s mission to help consumers and businesses reduce their transportation energy costs while meeting or exceeding vehicle performance expectations. The Propulsion Materials research portfolio seeks to develop higher performance materials that can withstand increasingly extreme environments and address the future properties needs of a variety of high efficiency powertrain types, sizes, fueling concepts, and combustion modes. Advanced Lightweight Materials research enables improvements in fuel economy by providing properties that are equal to or better than traditional materials at a lower weight. Because it takes less energy to accelerate a lighter object, replacing cast iron and traditional steel components with lightweight materials such as high-strength steel, magnesium (Mg), aluminum (Al), and polymer composites can directly reduce a vehicle’s fuel consumption. Materials technology activities focus on the following cost and performance targets: (1) enable a 25 percent weight reduction for light-duty vehicles including body, chassis, and interior as compared to a 2012 baseline at no more than a $5/lb-saved increase in cost; and (2) validate a 25 percent improvement in high temperature (300°C) component strength relative to components made with 2010 baseline cast Al alloys (A319 or A356) for improved efficiency light-duty engines.

36 MATERIALS SCIENCE↗

A study of structural, optical and dielectric properties of crystalline Sr{sub 2}Nb{sub 2}O{sub 7} nanoparticles synthesized by a modified combustion technique

Nanocrystalline Strontium Pyroniobate is synthesized by a novel auto-igniting combustion technique. The X-Ray diffraction studies reveal that Strontium Niobate possesses orthorhombic structure. Phase purity and structure of the nanopowder is further examined using Fourier-Transform Infrared and Raman spectroscopy. The average particle size of the as prepared nanoparticles from the Transmission Electron Microscopy is 30 nm. Sr{sub 2}Nb{sub 2}O{sub 7} is a photoluminescent material and the optical band gap determined from the UV-DRS spectrum is 2.7eV. The sample is sintered at an optimized temperature of 1350°C for 2 hours and obtained maximum density. The dielectric constant and loss factor values obtained at 5MHz for a well-sintered Strontium Niobate pellet is found to be 40 and 3.9×10{sup −3} respectively, at room temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Co-Hydrotreatment of Pyrolytic Lignin and Waste Cooking Oil to Produce Hydrocarbons

The co-hydrotreatment of pyrolysis bio-oils and vegetable oils could facilitate the integration of bioderived fuels into existing fuel infrastructures without significant modifications. Co-hydrotreatment studies with different PL/WCO blend ratios (0, 10, 20, 30, and 40 wt %) were conducted over the NiMo/γ-Al 2 O 3 catalyst. The coke formation value for WCO was 0.7 wt % and ranged between 1.5 and 2.5 wt % with the increase of pyrolytic lignin in the blend. The data suggest that coke is formed from both the sugar- and lignin-derived oligomers since the coke yield reported in this study is comparable with the coke yield obtained by coprocessing the bio-oil fraction without light oxygenate compounds, based on previous studies. All blends are recommended for co-hydrotreatment based on coke yield. The resulting organic phase was distilled into hydrocarbons at <150 °C, 150 to 250 °C, and 250 to 350 °C. The organic product’s overall hydrocarbon distribution was strongly dependent on the pyrolytic lignin concentration. The yield of the distillation cut with a boiling point range between 250 and 350 °C was higher in the hydrotreated samples, with more than 20% during distillation. Two-dimensional GC×GC was used to determine carbon distribution on the combustibles. FTIR and UV fluorescence spectra showed that most feedstocks were converted to potential combustibles for transportation applications after hydrotreatment. The distillation cuts properties, such as density, viscosity, and surface tension, were reported and compared to transportation fuel properties. Hydrocarbon yields reveal the potential of cohydrotreatment to upgrade pyrolytic lignin into valuable products. Furthermore, these findings provide useful insights into utilizing pyrolytic lignin to produce promising combustibles suitable for transportation applications.

co-hydrotreatment↗

The Combustion Phase of Burning Metals

Glassman's hypothesis and burn ratio are examined for their suitability for predicting the phase of combustion of metals. Neither criterion is validated based on either published property values or experimental evidence. Inconsistencies in published property values and definitions are noted. Computer calculations provide a more appropriate descriptions of the compositions of the combustion products and the adiabatic flame temperature of a burning metal at equilibrium. Dissociation temperatures (and product compositions) for 11 metals are computed using a specified quantity of thermal energy and compared with adiabatic flame temperatures.

Steinberg, Theodore A.↗

The PDF method for turbulent combustion

Probability Density Function (PDF) methods provide a means of calculating the properties of turbulent reacting flows. They have been successfully applied to many turbulent flames, including some with finite rate kinetic effects. Here the methods are reviewed with an emphasis on computational issues and their application to turbulent combustion.

Pope, S. B.↗

Solution combustion synthesis of iron-based alumina catalysts for dehydrogenation of fossil fuels

Microwave-assisted thermocatalytic dehydrogenation of fossil fuels has been proposed as a method for hydrogen production with no CO2 emissions. The byproduct is carbon, which has a commercial value. Iron-based alumina nanocomposites are promising catalysts for this process as they both absorb microwave radiation and catalyze the dehydrogenation. In addition, they may have magnetic properties, which could be used for their separation from the carbon byproduct. Solution combustion synthesis (SCS) is an attractive technique for the fabrication of iron-based alumina nanocomposites because it can produce high specific surface area oxides in a facile manner. However, the effects of the heating mode, the fuel, and the iron/aluminum ratio on the combustion synthesis behavior and the product properties have not been studied yet. In the present work, the iron-based alumina nanocomposites were obtained by SCS using a hotplate, a muffle furnace, and a microwave oven. The initial mixtures were aqueous solutions of iron nitrate, aluminum nitrate, and an organic fuel. The concentrations of the two nitrates were varied in proportion to Fe:Al molar ratios of 1:2, 1:1, and 2:1. Two fuels were tested: citric acid and glycine. The combustion was less vigorous when citric acid was used as the fuel, which is explained by the lower exothermicity of the reaction. X-ray diffraction analysis of the products confirmed the formation of complex oxides of Fe and Al, specifically it detected hercynite and magnetite phases. Brunauer-Emmett-Teller surface area analysis has shown that the powders obtained using citric acid have specific surface areas as high as 276 m2/g, significantly higher than those obtained using glycine. Muffle furnace and hotplate heating led to comparable specific surface areas, while microwave heating resulted in significantly lower specific surface areas. The magnetic properties of the products increase with increasing the Fe/Al molar ratio from 1:2 (no response to a magnetic field) to 1:1 (weak response) and 2:1 (strong response).

solution combustion synthesis, nanoscale oxides, f↗

Finite-rate water condensation in combustion-heated wind tunnels

A quasi-one-dimensional method for computing finite rate nucleation and droplet growth of water in a supersonic expansion of combustion products is presented. Sample computations are included for the Langley 8 foot High Temperature Tunnel, but the method can also be applied to other combustion heated wind tunnels. The sample results indicate that the free stream static pressure can be in the range of 25 to 60 percent greater than that computed for isentropic nozzle flow without water condensation. The method provides a tool for examining the effects of water condensation on static state properties and velocity of the supersonic stream in combustion heated wind tunnels.

Erickson, Wayne D.↗

A detailed modeling study of radiative heat transfer in a heavy-duty diesel engine

In recent years, the importance of radiative heat transfer in combustion has been increasingly recognized. Detailed models have become available that accurately represent the complex spectral radiative properties of reacting gas mixtures and soot particles, and new methods have been developed to solve the radiative transfer equation (RTE). At the same time, the trends toward higher operating pressures and higher levels of exhaust-gas recirculation in compression-ignition engines, together with the demand for higher quantitative accuracy from in-cylinder CFD models, has led to renewed interest in radiative transfer in engines. In this report an in-depth investigation of radiative heat transfer is performed for a heavy-duty diesel truck engine over a range of operating conditions. Results from 10 different combinations of turbulent combustion models, spectral radiation property models, and RTE solvers are compared to provide insight into the global influences of radiation on energy redistribution in the combustion chamber, heat losses, and engine-out pollutant emissions (NO and soot). Also, the relative importance of the individual contributions of molecular gas versus soot radiation, the spectral model, the RTE solver, and unresolved turbulent fluctuations in composition and temperature (turbulence–radiation interactions – TRI) are investigated. Local instantaneous temperatures change by as much as 100 K with consideration of radiation, but the global influences of radiation on heat losses and engine-out emissions are relatively small (in the 5–10% range). Molecular gas radiation dominates over soot radiation, consideration of spectral properties is essential for accurate predictions of reabsorption, a simple RTE solver (a first-order spherical harmonics – P1 – method) is sufficient for the conditions investigated, and TRI effects are small (less than 10%). While the global influences of radiation are relatively small, it is nevertheless desirable to explicitly account for radiation in in-cylinder CFD. To that end, a simplified CFD radiation model has been proposed, based on the findings reported here.

42 ENGINEERING↗

A Modeling Study on Ammonia and Ammonia/Hydrogen Kinetics for Gas Turbine Engines

The use of ammonia as a fuel source in gas turbine engine power cycles represents an attractive means to decarbonize the energy sector due to higher energy density and achieving liquid state at far lower pressures compared to pure hydrogen. However, due to low flammability and a propensity for high NOx emissions, its use is not without challenge. Here, a number of 0D and 1D modeling tools were utilized to study the combustion characteristics of ammonia and ammonia/hydrogen mixtures, examining basic fundamental properties such as laminar flame speed, variability among existing chemical kinetic mechanisms, and considering the use of two-stage rich-lean combustion strategies to achieve low NOx emissions.

42 ENGINEERING↗

Microwave-assisted pyrolysis of liquid hydrocarbons using iron-based alumina catalysts obtained by solution combustion synthesis: The effect of synthesis parameters

The microwave-absorbing and catalytic properties of iron-based alumina (FeAl x O y ) materials have enabled their use as catalysts for the microwave-assisted generation of hydrogen and carbon via pyrolysis of hydrocarbons. Solution combustion synthesis (SCS) is a promising method to fabricate these materials, but the pyrolysis performance still needs to be improved. The present work investigated how altering the SCS parameters affects the pyrolysis of diesel fuel, gasoline, and crude oil. Two fuels (citric acid and glycine), four Fe:Al molar ratios, and two heating modes (hotplate and furnace) were tested. Fe/γ-Al 2 O 3 and Fe/β-SiC catalysts were prepared via incipient wetness impregnation for comparison. Among the three fossil fuels tested, diesel fuel yielded the highest amounts of H 2 and least amounts of CO x . The choice of fuel for the SCS process and the Fe/Al ratio strongly affected pyrolysis performance as they influence properties important for both catalysis and microwave absorption. The use of glycine resulted in catalysts that exhibited high H 2 yield and low CO 2 generation, which is explained by the revealed structural differences. The increase in the Fe:Al molar ratio accelerated microwave heating by adding more magnetic loss but also increased the amount of CO x . When the optimal SCS parameters were used, FeAl x O y catalysts outperformed Fe/γ-Al 2 O 3 and Fe/β-SiC. The high H 2 generation efficiency of the SCS catalysts is explained by their enhanced microwave-absorption properties. Scanning electron microscopy and energy dispersive X-ray spectroscopy revealed the formation of large-diameter CNTs via the tip-growth mechanism. The regeneration of SCS catalysts was demonstrated via the Boudouard reaction.

Carbon nanotubes↗

Experimental Investigation of Low Cost, Low Thermal Conductivity Thermal Barrier Coating on HCCI Combustion, Efficiency, and Emissions

In-cylinder surface temperature is of heightened importance for Homogeneous Charge Compression Ignition (HCCI) combustion since the combustion mechanism is thermo-kinetically driven. Thermal Barrier Coatings (TBCs) selectively manipulate the in-cylinder surface temperature, providing an avenue for improving thermal and combustion efficiency. A surface temperature swing during combustion/expansion reduces heat transfer losses, leading to more complete combustion and reduced emissions. At the same time, achieving a highly dynamic response sidesteps preheating of charge during intake and eliminates the volumetric efficiency penalty. The magnitude and temporal profile of the dynamic surface temperature swing is affected by the TBC material properties, thickness, morphology, engine speed, and heat flux from the combustion process. This study follows prior work of authors with Yttria Stabilized Zirconia, which systematically engineered coatings for HCCI combustion. Herein, a modeling study was used to assess the impacts of various TBC material properties, e.g. density, thickness, and thermal conductivity on the temperature swing effect. Reducing conductivity emerged as a most promising avenue, rather than reducing both the density and effective conductivity by increasing porosity, the current work emphasizes a material with natively low conductivity. A novel TBC formulation was developed, leverages a class of materials that, to the author’s best knowledge, have not been used as a thermal barrier coating previously. Here, a systematic experimental investigation was carried out using single-cylinder research engine. Experimental engine studies utilizing the novel ‘glassy’ low-K coating exhibit advanced ignition phasing and reduced combustion duration relative to the baseline engine. Heat transfer measurements indicate a net reduction in heat flux over the entire cycle, although main effect is felt during expansion, and the reduced heat transfer losses manifest in higher gross indicated thermal efficiency by approximately 5-6% on a relative basis.

42 ENGINEERING↗

Effect of Unleaded Gasoline—Biofuel Blends on Exhaust Emissions

Biodiesels and biomass EtOH are currently considered the most applicable and essential biomass fuels. Furthermore, MeOH and BuOH are also attracting attention as alternatives. These fuel types can be used to reduce exhaust emissions from gasoline engines because they are renewable oxygenated bioresources. Three biofuel additives, namely, MeOH (10%, M10), EtOH (10%, E10), and BuOH (10%, B10) were used to compare the engine performance properties and exhaust gas emission levels upon combustion of mixed biomass fuels and pure petroleum fuel (clean unleaded gasoline, E0). The engine combustion temperature dropped by 4.32%, O{sub 2} emission increased by 6.67%, NO{sub x} emissions decreased by 13.46%, CO emission decreased by 44%, and hydrocarbon emissions fell by 29% if biomass fuels were used. Therefore, mixed biofuel additives and gasoline could substantially reduce engine exhaust emissions, including oxides of C and N, hydrocarbons, etc., because the biofuels contain higher oxygen contents that facilitate complete combustion.

09 BIOMASS FUELS↗

Laser Additive Manufacturing of (Ti-6Al-4V)/10 wt.% Ag Composite Using Spherical Powders to Reduce Wear and Friction

In order to extend the service lifetime of Ti-6Al-4V-based components, friction and wear behaviors of Ti-6Al-4V alloys needed to be further improved. Laser additive manufacturing with a moving laser beam was used to prepare (Ti-6Al-4V)/10 wt.% Ag samples, on a three-dimensional RC-SLM400 printer with laser powers of 2-10 kW. (Ti-6Al-4V)/10 wt.% Ag samples were successfully printed using spherical powders prepared by gas atomization process (SPGAP) and combustion reaction (SP-CR). The tribological properties of the as-prepared samples sliding against Si{sub 3}N{sub 4} balls were examined using a ball-on-disk tribometer. The results showed that the tribological behavior of (Ti-6Al-4V)/10 wt.% Ag printed by SP-CR was better than that of the sample printed by SPGAP. The low friction and reduced wear were mainly attributed to the formation of the lubrication layer containing large amounts of silver, which can exhibit an excellent deformation and plastic ductility. It effectively reduced the friction resistance and material loss and provided the good lubrication for 0-80 min, resulting in low friction and reduced wear of the samples prepared by SP-CR.

36 MATERIALS SCIENCE↗

Holistic comparison of environmental barrier coating material candidates through design of a figure of merit

The first figure of merit for environmental barrier coating (EBC) materials was designed through a ranking system for material properties pertaining to established EBC failure modes in service. Seven past, present, and novel EBC candidate materials were used in the figure of merit design: SiO 2 , Ba 0.75 Sr 0.25 Al 2 Si 2 O 8 (BSAS), HfSiO 4 , Yb 2 Si 2 O 7 , Yb 2 SiO 5 , Yb 2 O 3 , and YbPO 4 . Utilizing compiled data from the literature, the presented figure of merit verified Yb 2 Si 2 O 7 as the state-of-the-art candidate with optimal EBC properties and inferred that YbPO 4 should be considered as a potentially viable EBC material candidate. Further, the figure of merit allows for a holistic comparison of EBC candidates and informs experimental and computational search efforts for next-generation complex EBCs. Clear knowledge gaps found through this work include CaO–MgO–Al 2 O 3 –SiO 2 (CMAS)-resistant coatings, EBC lifetimes before delamination, and oxidant diffusion rates in relevant EBC microstructures. It was shown that while some materials show promise for solving a single key failure mode for EBCs (i.e., CMAS reactivity), a community-wide goal should be placed on materials development to achieve acceptable resistance against all major failure modes, which are interconnected. Novel compositionally complex EBC materials, in addition to layered EBC architectures, show promise for the optimization of material properties for long-lifetime EBCs in combustion environments.

36 MATERIALS SCIENCE↗

Tests to Reduce TorreCat™ Technology to Practice

Torrefaction is the thermal treatment of materials in the absence of oxygen in the temperature range of 200 to 300 °C and has been shown to improve handling and grinding properties, hydrophobicity, volatiles content, energy density, and combustion performance of renewable energy biomass feedstock materials. The disadvantages of torrefaction are its relative high cost compared to the low value input feedstock material and the energy that can be lost to volatized gases. This work will demonstrate a new technology developed by Advanced Torrefaction Systems (ATS), known as TorreCat™ Technology, that uses an oxidation catalyst in a closed system to combust and destroy volatile organic compounds (VOCs) and other byproducts produced in the torrefaction process. An oxidation catalyst is a substance, or a combination of substances, that accelerate the rate of a chemical reaction without being consumed by the reaction. Catalytic combustion is a reaction that occurs at temperatures 50% lower than traditional combustion, such that essentially no NOx is created. The output of the oxidation catalyst (flue gas) consists mainly of superheated steam and inert gases (carbon dioxide and nitrogen), which can be used for heat in the thermal treatment process. INL has previously developed a pilot-scale Continuous-Feed Thermal Treatment System (CFTTS) that has 10 kg/hr capacity but does not reform the flue gas to reduce environmental concerns or capture all available heat from the biomass material. Using the TorreCat™ technology in INL’s thermal treatment system will demonstrate increased thermal efficiencies during the treatment process as well as reduced environmental impact and clean-up costs. The objective of this project is to determine the effectiveness of the Torrecat™ technology to reform the flue gas and capture as much of its heat content as possible.

36 MATERIALS SCIENCE↗

Final Report: Utilizing Alternative Fuel Ignition Properties to Improve SI and CI Engine Efficiency

Experimental and modeling studies were completed to explore leveraging physical and chemical fuel properties for improved thermal efficiency of internal combustion engines. Fundamental studies of the ignition chemistry of ethanol and iso-octane blends and constant volume spray chamber studies of gasoline and diesel sprays supported the core research effort which used several reciprocating engine platforms. Single cylinder spark ignition (SI) engine studies were carried out to characterize the impact of ethanol/gasoline, syngas (H 2 and CO)/gasoline and other oxygenate/gasoline blends on engine performance. The results of the single-cylinder engine experiments and other data from the literature were used to train a GT Power model and to develop a knock criteria based on reaction chemistry. The models were used to interpret the experimental results and project future performance. Studies were also carried out using a state of the art, direct injection (DI) turbocharged multi- cylinder engine with piezo-actuated fuel injectors to demonstrate the promising spray and spark timing strategies from single-cylinder engine studies on the multi-cylinder engine. Key outcomes and conclusions of the studies were: 1. Efficiency benefits of ethanol and gasoline fuel blends were consistent and substantial (e.g. 5-8% absolute improvement in gross indicated thermal efficiency (GITE)). 2. The best ethanol/gasoline blend (based on maximum thermal efficiency) was determined by the engine hardware and limits based on component protection (e.g. peak in-cylinder pressure or maximum turbocharger inlet temperature) – and not by knock limits. Blends with <50% ethanol delivered significant thermal efficiency gains with conventional SI hardware while maintain good safety integrity to the engine hardware. 3. Other compositions of fuel blends including syngas (H 2 and CO) and other dilution strategies provided significant efficiency gains as well (e.g. 5% absolute improvement in ITE). 4. When the combination of engine and fuel system is not knock limited, multiple fuel injection events maintain thermal efficiency while improving engine-out emissions (e.g. CO, UHC, and particulate number).

33 ADVANCED PROPULSION SYSTEMS↗