Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Exploring the Effects of Piston Bowl Geometry and Injector Included Angle on Dual-Fuel and Single-Fuel RCCI

Abstract Reactivity control compression ignition (RCCI) is a low-temperature combustion technique that has been proposed to meet the current demand for high thermal efficiency and low engine-out emissions. However, its requirement of two separate fuel systems (i.e., a low-reactivity fuel system and a high-reactivity fuel system) has been one of its major challenges in the last decade. This leads to the single-fuel RCCI concept, where the secondary fuel (reformates of diesel) is generated from the primary fuel (diesel) through catalytic partial oxidation reformation. Following the in-depth analysis of the reformate fuel (reformates of diesel) and its benefit as the low-reactivity fuel with diesel, the effects of the start of injection (SOI) timing of diesel and the energy-based blend ratio were also studied in detail. In this study, the effects of piston profile and the injector included angles were experimentally examined using both conventional fuel pairs (gasoline—diesel and natural gas—diesel) and reformate RCCI. A validated computational fluid dynamics (CFD) model was also used for a better understanding of the experimental trends. Comparing a reentrant bowl piston with a shallow bowl piston at a constant compression ratio and SOI, the latter showed better thermal efficiency, regardless of the fuel combination, due to its 10% lower surface area for the heat transfer. Comparing the 150-degree included angle and 60-degree included angle on the shallow bowl piston, the latter showed better combustion efficiency, regardless of the fuel combination, due to its earlier combustion phasing (at constant SOI timing). The effect was particularly prominent on reformate RCCI because of its incredibly high diluent concentration, which retards the combustion further for the 150-deg injector. Later, using convergecfd, seven different injector included angles were studied at a constant SOI. With the change in injector included angle, the region of the cylinder targeted by the fuel spray varies significantly, and it was found to have a significant impact on the combustion efficiency and the engine-out emissions. As the injector included angle changed from 60-deg to 150-deg, the combustion efficiency increased by 15% and the CO, NOx, and HC emissions decreased by 96%, 70%, and 86%, respectively.

Engineering↗

Effect of cooler electrons on a compressive ion acoustic solitary wave in a warm ion plasma — Forbidden regions, double layers, and supersolitons

It is observed that the presence of a minority component of cooler electrons in a three component plasma plays a deterministic role in the evolution of solitary waves, double layers, or the newly discovered structures called supersolitons. The inclusion of the cooler component of electrons in a single electron plasma produces sharp increase in nonlinearity in spite of a decrease in the overall energy of the system. The effect maximizes at certain critical value of the number density of the cooler component (typically 15%–20%) giving rise to a hump in the amplitude variation profile. For larger amplitudes, the hump leads to a forbidden region in the ambient cooler electron concentration which dissociates the overall existence domain of solitary wave solutions in two distinct parameter regime. It is observed that an inclusion of the cooler component of electrons as low as < 1% affects the plasma system significantly resulting in compressive double layers. The solution is further affected by the cold to hot electron temperature ratio. In an adequately hotter bulk plasma (i.e., moderately low cold to hot electron temperature ratio), the parameter domain of compressive double layers is bounded by a sharp discontinuity in the corresponding amplitude variation profile which may lead to supersolitons.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A Planar Biaxial Experiment Platform for In Situ High-Energy Diffraction Studies

In this work, an experimental platform for multiscale studies of materials subjected to plane stress loads is presented. Specifically, a planar biaxial mechanical load frame with four independent hydraulic actuators capable of applying arbitrary loading paths and ratios of tension and compression was designed and built for in situ diffraction experimentation. The load frame is integrated for use at the Argonne National Laboratory Advanced Photon Source (APS) synchrotron, Sector 1, 1-ID-E endstation and the Los Alamos Neutron Science Center (LANSCE) spallation neutron source, Spectrometer for Materials Research at Temperature and Stress (SMARTS) instrument. Cruciform specimen geometries were designed to experience loading ratios in the gauges commensurate with those applied at the grips, and to minimize interference with diffracted X-rays and neutrons. The finite element models used to design the cruciform specimen geometries were experimentally validated using stereo digital image correlation measurements. This complete planar biaxial in situ diffraction platform provides a new capability for studying multiaxial micromechanics of crystalline materials (e.g., elastic, slip, twinning, phase transformation) and their dependencies on grain size, location, texture, and neighborhood characteristics. The coupling with far-field high energy diffraction microscopy (ff-HEDM) for grain-by-grain measurements provides an additional benefit; provided crystal elastic constants of a material are known, it enables the direct measurement of local and average stress tensors in the gauge sections of cruciform specimens, resolving a long outstanding challenge of planar biaxial mechanical testing.

36 MATERIALS SCIENCE↗

Properties of mortars made by uncalcined FGD gypsum-fly ash-ground granulated blast furnace slag composite binder

Highlights: Black-Right-Pointing-Pointer The mortar with uncalcined FGD gypsum has suitable workability. Black-Right-Pointing-Pointer The strength of mortar with uncalcined FGD gypsum is higher than that of mortar without uncalcined FGD gypsum. Black-Right-Pointing-Pointer The dry shrinkage of mortar with uncalcined FGD gypsum is lower than that of mortar without uncalcined FGD gypsum. Black-Right-Pointing-Pointer The leaching of sulfate ion of mortar is studied. - Abstract: A series of novel mortars were developed from composite binder of uncalcined FGD gypsum, fly ash (FA) and ground granulated blast furnace slag (GGBFS) for the good utilization of flue gas desulphurization (FGD) gypsum. At a fixed ratio (20%) of GGBFS to the composite binder, keeping consistency of the mortar between 9.5 and 10.0 cm, the properties of the composite mortar were studied. The results show that higher water/binder (W/B) is required to keep the consistency when increasing the percentage of FGD gypsum. No obvious influences of the W/B and content of FGD gypsum on the bleeding of paste were observed which keeps lower than 2% under all experimental conditions tried. The highest compressive and flexural strengths (ratio is 20% FGD gypsum, 20% GGBFS and 60% FA) are 22.6 and 4.3 MPa at 28 days, respectively. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) results indicate that massive ettringite crystals and C-S-H gels exist in the hydration products. At 90 days the mortars with FGD gypsum is dramatically smaller drying shrinkage (563-938 micro strain) than that without FGD gypsum (about 2250 micro strain). The release of the SO{sub 4}{sup 2-} from the mortar was analyzed, indicating that the dissolution of sulfate increases with FGD gypsum. The concentration of SO{sub 4}{sup 2-} releasing from the mortar with 10% FGD gypsum is almost equal to that obtained from the mortar without FGD gypsum. The release of SO{sub 4}{sup 2-} from the mortar with 20% FGD gypsum is 9200 mg{center_dot}m{sup -2}, which is lower than that from the mortar with 95% cement clinker and 5% FGD gypsum.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Synthesis and characterization of two novel chiral-type formate frameworks templated by protonated diethylamine and ammonium cations

Two novel formate frameworks templated by ammonium and diethylammonium (DEtA{sup +}) cations have been synthesized. Chemical analysis as well as optical, Raman and IR studies showed partial substitution of nickel ions by Cr(III) or Fe(III). X-ray diffraction revealed that these compounds crystallize in the chiral-type structure of P6{sub 3}22 symmetry. The oxygen atoms from formate ligands form octahedral coordination around the metal centers and the octahedra are bridged by the formate groups in the anti-anti mode configuration forming the hexagonal structure with large channels expanding along the c direction. The channels are filled with disordered DEtA{sup +} and NH{sub 4}{sup +} ions and they show unusual compression with the c/a ratio of only 0.862 and 0.852 for the iron- and chromium-containing compound, respectively. Magnetic studies revealed that the both compounds order magnetically at low temperatures but the ordering temperature is significantly higher for the iron compound (37 K) compared to the chromium analogue (26 K). - Graphical abstract: Temperature dependence of magnetization M of DEtAFeNi showing magnetic order at 37 K. - Highlights: • Two novel chiral formates of P6{sub 3}22 symmetry were synthesized. • The structures contain strongly compressed hexagonal channels filled with disordered cations. • The obtained compounds exhibit magnetic order at low temperatures. • Raman, IR and absorption spectra prove incorporation of Cr(III) and Fe(III) in the frameworks.

36 MATERIALS SCIENCE↗

Comprehensive Studies on Hot Compaction and Vibration-Assisted Compaction Tests of Aluminum Powder

Abstract Aluminum powder compaction was studied using both test and simulation. Cold compaction, hot compaction, and vibration-assisted (cold) compaction tests were conducted to achieve different density ratios. First, the hot compaction test (at 300 °C, compression pressure 140 MPa) improved about 6% compared with cold compaction under the same compression pressure. Second, although the relative density ratio does not obviously improve at a vibration-assisted (cold) compaction, the strength of the specimens made under vibration loading is much better than those of cold compaction. Additionally, finite element models with well-calibrated Drucker–Prager Cap (DPC) material constitutive model were built in abaqus/standard to simulate the powder compaction process. The results of the finite element model have very good correlations with test results up to the tested range, and this finite element model further predicts the loading conditions needed to achieve the higher density ratios. Two exponential equations of the predicted density ratio were obtained by combining the test data and the simulation results. A new analytical solution was developed to predict the axial pressure versus the density ratio for the powder compaction according to DPC material model. The results between the analytical solution and the simulation model have a very good match.

Engineering↗

Utilization of municipal solid waste incineration fly ash for sulfoaluminate cement clinker production

Highlights: > The replacement can be taken up to 30% of MSWI fly ash in the raw mix. > The novelty compositional parameters were defined, their optimum values were determined. > Expansive property of SAC is strongly depended on gypsum content. > Three leaching test methods are used to assess the environmental impact. - Abstract: The feasibility of partially substituting raw materials with municipal solid waste incineration (MSWI) fly ash in sulfoaluminate cement (SAC) clinker production was investigated by X-ray diffraction (XRD), compressive strength and free expansion ratio testing. Three different leaching tests were used to assess the environmental impact of the produced material. Experimental results show that the replacement of MSWI fly ash could be taken up to 30% in the raw mixes. The good quality SAC clinkers are obtained by controlling the compositional parameters at alkalinity modulus (C{sub m}) around 1.05, alumina-sulfur ratio (P) around 2.5, alumina-silica ratio (N) around 2.0{approx}3.0 and firing the raw mixes at 1250 deg. C for 2 h. The compressive strengths of SAC are high in early age while that develop slowly in later age. Results also show that the expansive properties of SAC are strongly depended on the gypsum content. Leaching studies of toxic elements in the hydrated SAC-based system reveal that all the investigated elements are well bounded in the clinker minerals or immobilized by the hydration products. Although some limited positive results indicate that the SAC prepared from MSWI fly ash would present no immediate thread to the environment, the long-term toxicity leaching behavior needs to be further studied.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Different site occupancies in substitution variants of Mo{sub 3}Sb{sub 7}

A series of samples with the initial formula Mo{sub 3–x}Fe{sub x}Sb{sub 7} and Mo{sub 3–x}Ni{sub x}Sb{sub 7} have been prepared by solid state reaction at 873 K, starting from the elements in the stoichiometric ratios. The materials were compressed via hot-pressing, and their thermoelectric properties determined. Single crystal data show that Ni atoms in part occupy the cubic voids of the Mo{sub 3}Sb{sub 7} structure, as well as replace some Mo atoms, in contrast to the Fe analogues, where we found no evidence for Fe in the cubic voids. Supported by electronic structure calculations, replacing Mo with Fe or Ni increases the valence-electron count, thus decreases the numbers of p-type carriers of Mo{sub 3}Sb{sub 7}. On the other hand, filling the holes with Ni atoms appears to have no such effect. As a consequence, the Ni containing samples exhibit higher electrical conductivity than the Fe analogues, and ultimately lower thermoelectric figure-of-merit, as the p-type carrier concentration remains too high. - Graphical abstract: Trying to substitute Ni atoms for Mo in Mo{sub 3}Sb{sub 7} resulted in partial filling of the cubic voids, in contrast to Mo{sub 3–x}Fe{sub x}Sb{sub 7}. Since the Ni atoms in the Sb{sub 8} cubes do not act as electron donors, the Ni-containing materials exhibit very high carrier concentration, and thus high electric conductivity and low Seebeck coefficient. - Highlights: • Various substitution variants of Mo{sub 3}Sb{sub 7} with Fe and Ni were characterized. • While the Fe atoms replace the Mo atoms, the Ni atoms also fill the cubic voids. • Higher Fe/Ni amount on the Mo sites causes a decrease of the charge carriers. • The Ni atoms on the cubic sites do not decrease the charge carriers. • The lower the carrier concentration, the better the thermoelectric properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Isosymmetric pressure-induced bonding increase changes compression behavior of clinopyroxenes across jadeite-aegirine solid solution in subduction zones

Pyroxenes are among the most important minerals of Earth's crust and upper mantle and play significant role in controlling subduction at convergent margins. In this study, synchrotron-based single-crystal X-ray diffraction experiments were carried out on a natural aegirine [NaFe 3+ Si 2 O 6 ] sample at ambient temperature and high pressures to 60 GPa, simulating conditions within the coldest part of a subduction zone consisting of old lithosphere. The diffraction data reveal no obvious sign of structural phase transition in aegirine within this pressure range; however, several relevant structural parameter trends change noticeably at approximately 24 GPa, indicating the presence of the previously predicted isosymmetric bonding change, related to increase of coordination number of Na + at M2 site. The pressure-volume data, fit with third-order Birch-Murnaghan (BM3) equation of state over the whole pressure range, yields K T0 = 126(2) GPa and K' T0 = 3.3(1), while separate BM3 fits performed for the 0–24.0 GPa and 29.9–60.4 GPa pressure ranges give K T0 = 118(3) GPa, K' T0 = 4.2(3) and K T0 = 133(2) GPa, K' T0 = 3.0(1), suggesting that the structure stiffens as a result of the new bond formation. Aegirine exhibits strong anisotropic compression with unit strain axial ratios ε 1 :ε 2 :ε 3 = 1.00:2.44:1.64. Structural refinements reveal that NaO 8 polyhedron is the most compressible and SiO 4 tetrahedron has the lowest compressibility. Lastly, the consequence of bonding transition is that the compressional behavior of aegirine below ~24 GPa and above that pressure is quite different, with likely consequences for relevant thermodynamic parameters and ion diffusion coefficients.

58 GEOSCIENCES↗

An experimental and kinetic modeling study of the ignition of 2-methyl decane

Ignition delay times (IDTs) of 2-methyl decane (C 11 H 24 -2) are measured in a high-pressure shock tube and in a rapid compression machine at equivalence ratios in the range 0.5–2.0 at 90 % dilution, at temperatures in the range 600–1430 K and at pressures of 15 and 30 bar. To clarify the effect of the branched methyl group on fuel oxidation, IDTs of n-undecane (nC 11 H 24 ) are also measured at similar conditions to those measured for C 11 H 24 -2. A new chemical kinetic mechanism, using C3MechV4.0.1 as the core chemistry, is developed and validated against the new experimental data. The thermodynamic properties of the fuel (RH), alkyl (Ṙ), alkyl peroxy (RȮ 2 ), hydroperoxy-alkyl (Q̇OOH), and peroxy hydroperoxy alkyl (Ȯ 2 QOOH) radicals are updated in both the C 11 H 24 -2 and nC 11 H24 models using THERM25. A reaction path flux analysis for C 11 H 24 -2 at different temperatures was conducted. Compared to nC 11 H 24 , C 11 H 24 -2 shows slower reactivity. At low and intermediate temperatures, the chain propagation pathway Q̇OOH ↔ C 11 cyclic ether + ȮH is favored for C 11 H 24 -2, while the chain branching pathway Q̇OOH ↔ Ȯ 2 QOOH ↔ C 11 carbonyl hydroperoxide (KHP) + ȮH is suppressed, leading to lower reactivity compared to nC 11 H 24 . At high temperatures, the presence of the branched methyl group inhibits the direct decomposition of the fuel, resulting in reduced C 2 H 4 formation, which in turn suppresses the reactivity of the fuel.

2-methyl decane↗

Effects of carbon nanotubes on twin and texture evolution of magnesium matrix composite during compression process

Highlights: • The CNTs existing at grain boundaries lead to stress concentration, and stimulate the formation of twins. • Crystal rotation and non-basal slip alternately dominate the deformation of the CNTs/Mg composite. • The texture changes from random texture to strong basal texture, strong non-basal texture at the three corresponding stages. • Crystal rotation and non-basal slip system are the main toughening mechanisms of the CNTs/Mg composite. - Abstract: A compression test is performed to investigate the effects of carbon nanotubes (CNTs) on twin and texture evolution of the 1.0 wt.% CNTs reinforced magnesium matrix (CNTs/Mg) composite. The compression process consists of elastic, yield and hardening stages, and the number of twin significantly increases at the yield stage. During the compression process, the crystal rotation and non-basal slip caused by twin shear alternately dominate the deformation of the 1.0 wt.% CNTs/Mg composite. The CNTs existing at grain boundaries lead to stress concentration, and the stress concentration stimulates the formation of twins at the yield stage. The formed twins interact with dislocations, result in crystal rotation and promotion of the non-basal slip system at the hardening stage under the effect of twin shear, thus, improve the toughness of the CNTs/Mg composite.

36 MATERIALS SCIENCE↗

Negative compressibility observed in graphene containing resonant impurities

We observed negative compressibility in monolayer graphene containing resonant impurities under different magnetic fields. Hydrogenous impurities were introduced into graphene by electron beam (e-beam) irradiation. Resonant states located in the energy region of {+-}0.04 eV around the charge neutrality point were probed in e-beam-irradiated graphene capacitors. Theoretical results based on tight-binding and Lifshitz models agreed well with experimental observations of graphene containing a low concentration of resonant impurities. The interaction between resonant states and Landau levels was detected by varying the applied magnetic field. The interaction mechanisms and enhancement of the negative compressibility in disordered graphene are discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evaluation of the effect of organic pro-degradant concentration in polypropylene exposed to the natural ageing

The production and consumption of plastics in the last decade has recorded a remarkable increase in the scientific and industrial interest in environmentally degradable polymer (EDPs). Polymers wastes are deposited improperly, such as dumps, landfills, rivers and seas, causing a serious problem by the accumulation in the environment. The abiotic processes, like the photodegradation, are the most efficient occurring in the open environmental, where the polymers undergo degradation from the action of sunlight that result from direct exposure to solar radiation, however depend of the type of chemical ageing, which is the principal component of climatic ageing. The subject of this work is to study the influence of concentration of organic pro-degradant (1, 2 and 3 % w/w) in the polypropylene (PP) exposed in natural ageing. PP samples with and without the additive were processed in plates square form, obtained by thermal compression molding (TCM) using a press at 200°C under 2 tons for 5 min, and then were exposed at natural ageing during 120 days. The presence of organic additive influenced on PP degradability, this fact was assessed by changes in the thermal and morphology properties of the samples after 120 days of natural ageing. Scanning Electronic Microscopy (SEM) results of the morphological surface of the modified PP samples showed greater degradation photochemical oxidative when compared to neat PP, due to increase of rugosity and formation of microvoids. PP samples with different pro-degradant concentration under natural ageing presented a degree of crystallinity, obtained by Differential Scanning Calorimeter (DSC) increases in comparing the neat PP.

36 MATERIALS SCIENCE↗

Properties of water surface discharge at different pulse repetition rates

The properties of water surface discharge plasma for variety of pulse repetition rates are investigated. A magnetic pulse compression (MPC) pulsed power modulator able to deliver pulse repetition rates up to 1000 Hz, with 0.5 J per pulse energy output at 25 kV, was used as the pulsed power source. Positive pulse with a point-to-plane electrode configuration was used for the experiments. The concentration and production yield of hydrogen peroxide (H₂O₂) were quantitatively measured and orange II organic dye was treated, to evaluate the chemical properties of the discharge reactor. Experimental results show that the physical and chemical properties of water surface discharge are not influenced by pulse repetition rate, very different from those observed for under water discharge. The production yield of H₂O₂ and degradation rate per pulse of the dye did not significantly vary at different pulse repetition rates under a constant discharge mode on water surface. In addition, the solution temperature, pH, and conductivity for both water surface and underwater discharge reactors were measured to compare their plasma properties for different pulse repetition rates. The results confirm that surface discharge can be employed at high pulse repetition rates as a reliable and advantageous method for industrial and environmental decontamination applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Acoustical, morphological and optical properties of oral rehydration salts (ORS)

Ultrasonic velocity, density and viscosity were measured in different concentrations of oral rehydration salts (ORS) at room temperature 303 k. From the experimental data other related thermodynamic parameters, viz adiabatic compressibility, intermolecular free length, acoustic impedence, relaxation time are calculated. The experimental data were discussed in the light of molecular interaction existing in the liquid mixtures. The results have been discussed in terms of solute-solvent interaction between the components. Structural characterization is important for development of new material. The morphology, structure and grain size of the samples are investigated by SEM. The optical properties of the sample have been studied using UV Visible spectroscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of cooling rate on the properties of high density polyethylene/multi-walled carbon nanotube composites

High density polyethylene (HDPE)/multi-walled carbon nanotube (MWCNT) nanocomposites were prepared by melt mixing using twin-screw extrusion. The extruded pellets were compression moulded at 200°C for 5min followed by cooling at different cooling rates (20°C/min and 300°C/min respectively) to produce sheets for characterization. Scanning electron microscopy (SEM) shows that the MWCNTs are uniformly dispersed in the HDPE. At 4 wt% addition of MWCNTs composite modulus increased by over 110% compared with the unfilled HDPE (regardless of the cooling rate). The yield strength of both unfilled and filled HDPE decreased after rapid cooling by about 10% due to a lower crystallinity and imperfect crystallites. The electrical percolation threshold of composites, irrespective of the cooling rate, is between a MWCNT concentration of 1∼2 wt%. Interestingly, the electrical resistivity of the rapidly cooled composite with 2 wt% MWCNTs is lower than that of the slowly cooled composites with the same MWCNT loading. This may be due to the lower crystallinity and smaller crystallites facilitating the formation of conductive pathways. This result may have significant implications for both process control and the tailoring of electrical conductivity in the manufacture of conductive HDPE/MWCNT nanocomposites.

36 MATERIALS SCIENCE↗

Distributed Neural Representation for Reactive In Situ Visualization

Implicit neural representations (INRs) have emerged as a powerful tool for compressing large-scale volume data. This opens up new possibilities for in situ visualization. However, the efficient application of INRs to distributed data remains an underexplored area. Here, in this work, we develop a distributed volumetric neural representation and optimize it for in situ visualization. Our technique eliminates data exchanges between processes, achieving state-of-the-art compression speed, quality and ratios. Our technique also enables the implementation of an efficient strategy for caching large-scale simulation data in high temporal frequencies, further facilitating the use of reactive in situ visualization in a wider range of scientific problems. We integrate this system with the Ascent infrastructure and evaluate its performance and usability using real-world simulations.

Wu, Qi↗

Magnetocaloric effect in La(Fe{sub x}Si{sub 1-x}){sub 13} ferromagnets

The isothermal changes in the magnetic entropy and the lattice entropy and the adiabatic temperature change in La(Fe{sub 0.88}Si{sub 0.12}){sub 13} and La(Fe{sub 0.86}Si{sub 0.14}){sub 13} ferromagnets in a magnetic field are calculated. The calculations are performed with a generalized magnetostriction model of a ferromagnet; the calculation results are compared to experimental data. It is shown that the change in the lattice entropy decreases the magnetocaloric effect and makes it possible to explain the experimental data obtained for La(Fe{sub x}Si{sub 1-x}){sub 13} (x = 0.86, 0.88) ferromagnets. The temperature dependences of the bulk compression moduli of these ferromagnets are calculated, and these dependences indicate a strong lattice softening in the vicinity of the magnetic phase transition in them. The thermal expansion coefficient and some magnetic properties of the ferromagnet with x = 0.86 are measured to determine the numerical values of the parameters entering into calculation formulas.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗