SEARCH · Search NASA
Results for “CRITICAL PRESSURE”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Film condensation with high heat fluxes and scaled experiments using pure steam for reactor containment cooling
Condensation tests were performed using a newly developed test facility for scaling the passive containment cooling system (PCCS) to a small modular reactor (SMR). The PCCS of the SMR plays a pivotal role in ensuring greater safety, reliability, and compactness than what is afforded by traditional reactors. Therefore, a well-designed PCCS is essential to SMRs. However, previous studies and test data were unsuitable for scaling, due to high variation in the test geometry and operating conditions. This study intends to close this research gap by using a novel designed scaled test facility consisting of vertical condensing test sections featuring 1-, 2-, and 4-inch-diameter condensing tubes with annular water cooling, and by applying superheated and saturated steam with different steam mass flow ranges of 5–25 g/s. Further, the primary test data, including axial temperatures, mass flow rates, and pressures, were used in conjunction with a standard data reduction method to estimate critical parameters such as heat fluxes, heat transfer coefficients, and condensation rates. These scaled test data would support improving empirical correlations and validating condensation models to identify scaling distortion for SMR PCCSs.
Implications of real-gas behavior on refractive index calculations for optical diagnostics of fuel–air mixing at high pressures
Three models to compute the refractive index of gaseous mixtures at real gas conditions are presented with the purpose to improve the accuracy of state relationships between refractive index and thermodynamic properties. Models are compared with experimental data to determine one that is applicable to high pressure mixtures with non-ideal thermodynamic behavior near or above a fluids’ critical point. The optimal model is applied to analyze adiabatic thermal mixing of fuel and air at typical diesel engine conditions. Our results show that the ideal gas mixture law is appropriate in the vapor region, assuming it is known, for example, from experimental measurements. Finally, the model is applied for binary fuel-air mixing at supercritical conditions to demonstrate its full potential.
A review of technical and regulatory limits for hydrogen blending in natural gas pipelines
We report there is rising interest globally in the use of hydrogen for the provision of electricity or heat to industry, transport, and other applications in low-carbon energy systems. While there is attention to build out dedicated hydrogen infrastructure in the long-term, blending hydrogen into the existing natural gas pipeline network is also thought to be a promising strategy for incorporating hydrogen in the near-term. However, hydrogen injection into the existing gas grid poses additional challenges and considerations related to the ability of current gas infrastructure to operate with blended hydrogen levels. This review paper focuses on analyzing the current understanding of how much hydrogen can be integrated into the gas grid from an operational perspective and identifies areas where more research is needed. The review discusses the technical limits in hydrogen blending for both transmission and distribution networks; facilities in both systems are analyzed with respect to critical operational parameters, such as decrease in energy density, increased flow speed and pressure losses. Safety related challenges such as, embrittlement, leakage and combustion are also discussed. The review also summarizes current regulatory limits to hydrogen blending in different countries, including ongoing or proposed pilot hydrogen blending projects.
In-Rod Sensor System Overview, Benefits and Recent Irradiation Test Results
Westinghouse is developing an In-Rod Sensor (IRS) System capable of measuring critical fuel rod parameters such as center-line fuel temperature, rod internal pressure and axial fuel pellet stack elongation without having penetrations to the fuel rod. The technology is similar to the Halden Reactor instrumentation, but the IRS system focuses on commercial fuel rod instrumentation. Both systems circumvent fuel rod penetrations, however the IRS system overcomes unique geometric challenges found in commercial fuel rod assemblies. The IRS could also play a key role in accelerated fuel qualification by allowing real-time measurements during separate effects tests, integral fuel testing or during irradiation of lead test rods or lead test assemblies. Combining these measurements with data acquired from targeted separate effects testing and multi-scale modelling could significantly reduce the time required to qualify new fuel and reduce the safety margin uncertainty of operating plants. The IRS is actively in development for Light Water Reactors (LWR) based fuel assemblies but can also be applied to Gen IV reactor designs with minimal modifications.
A Novel Multiphysics Multiscale Multiporosity Shale Gas Transport Model for Geomechanics/Flow Coupling in Steady and Transient States
Summary A novel multiphysics multiscale multiporosity shale gas transport (M3ST) model was developed to investigate shale gas transport in both transient and steady states. The microscale model component contains a kerogen domain and an inorganic matrix domain, and each domain has its own geomechanical and gas transport properties. Permeabilities of various shale cores were measured in the laboratory using a pulse decay permeameter (PDP) with different pore pressure and confining stress combinations. The PDP-measured apparent permeability as a function of pore pressure under two effective stresses was fitted using the microscale M3ST model component based on nonlinear least squares fitting (NLSF), and the fitted model parameters were able to provide accurate model predictions for another effective stress. The parameters and petrophysical properties determined in the steady state were then used in the transient-state, continuum-scale M3ST model component, which performed history matching of the evolutions of the upstream and downstream gas pressures. In addition, a double-exponential empirical model was developed as a powerful alternative to the M3ST model to fit laboratory-measured apparent permeability under various effective stresses and pore pressures. The developed M3ST model and the research findings in this study provided critical insights into the role of the multiphysics mechanisms, including geomechanics, fluid dynamics and transport, and the Klinkenberg effect on shale gas transport across different spatial scales in both steady and transient states.
Efficiently predicting pressure-composition-temperature diagrams to discover low-stability metal hydrides
Quantitatively accurate computational predictions of metal hydride thermodynamics are challenging but critical for alloy performance optimization across a multitude of technological domains, including hydrogen storage, compression, purification, and getters. Recent machine learning approaches have demonstrated great success in this area, but can potentially suffer from several shortcomings since they rely on imbalanced experimental training data and can have poor out-of-distribution (ood) test performance. Here, in this study, we circumvent such pitfalls by developing a computationally efficient, first principles-based workflow for direct prediction of metal hydride phase equilibrium, i.e., the pressure-composition-temperature (PCT) diagram. We then demonstrate its utility on predicting low stability hydrides derived from compositionally complex C14 Laves phase AB2 alloys. Specifically, we computationally predict and then experimentally validate an AB 2 alloy series (z < 0.6 for Ti 2−z Zr z CrMnFeNi) with ideal hydriding thermodynamics for a two-stage metal hydride-based compressor for pressurizing boil off from liquefied hydrogen. Importantly, this study lays the groundwork for accurate and efficient discovery/optimization of ood, low-stability hydrides for which purely data-driven approaches lack sufficient accuracy.
Performing k eff Validation of As-Loaded Criticality Safety Calculations Using UNF-ST&DARDS: Sensitivity Calculations
The general method for performing validation of as loaded criticality safety calculations using UNF ST&DARDS is presented in a paper by Clarity, which includes a description of the UNF-ST&DARDS system. Proof-of-principle analyses were performed in the summer of 2019 for MPC-32 dual purpose canisters (DPCs) containing pressurized water reactor (PWR) fuel assemblies. Summaries of these results are presented in this and a companion paper for this conference. The current paper describes the TSUNAMI-3D calculations performed to generate sensitivity data, and the companion paper discusses the selection of critical experiments applicable for validation of the 11 MPC-32 DPCs considered. The generation of sensitivity data for as-loaded spent nuclear fuel (SNF) DPCs is a challenge given the detailed model of the fuel compositions generated by UNF ST&DARDS. Each fuel assembly is modeled with its own irradiation history in 18 axial nodes, unless the fuel assembly is damaged and thus considered as fresh by design basis. This results in a set of 576 fuel compositions, each of which must be processed separately in a multigroup (MG) calculation. Therefore, a continuous-energy (CE) TSUNAMI-3D method was chosen to alleviate this challenge. Two CE TSUNAMI-3D methods are available in SCALE 6.2.3: the iterated fission probability (IFP) and contribution-linked eigenvalue sensitivity/uncertainty estimation via track-length importance characterization (CLUTCH). Since the IFP method is not feasible because of memory requirements associated with its implementation in SCALE, the CLUTCH method was selected for these calculations. CLUTCH has been implemented in SCALE in parallel, allowing long calculations to be performed in reasonable timeframes. The two primary user inputs necessary for CLUTCH calculations are the F*(r) mesh and the number of latent generations used in determining the F*(r) function. This F*(r) function is used as the importance function for fission chains originating in a given volume element (voxel), and it is calculated using the IFP method in the skipped generations. A large number of skipped generations is thus required to ensure accurate calculation of this importance function. In these calculations, 500 generations were used to calculate the F*(r) function. For more information regarding the calculation of F*(r), see Jones [4]. The remainder of this paper is focused on the selection of the F*(r) mesh and the number of latent generations.
Pressure Response Optimization of an Eddy Current-Driven Flyer Plate Valve for the ITER Shattered Pellet Injection System
One technique for mitigating disruptions in a tokamak is shattered pellet injection (SPI). SPI is a process in which a large solid pellet consisting of deuterium, neon, or argon is desublimated in a pipe gun barsrel and launched downstream. Pellets are shattered just before entering the plasma by an impact with an angled tube. Injection of these materials into the plasma radiates stored thermal energy, limits current decay rates, suppresses the generation of runaway electrons, and dissipates runaway electrons if necessary. A critical element of the SPI system is a fast-acting valve that releases high-pressure gas to dislodge and accelerate pellets directly, or indirectly via a mechanical punch. A prototype valve sized for the ITER SPI system has been designed and fabricated. A pulsed high-voltage power supply energizes the valve’s internal magnetic coil, which induces eddy currents in the adjacent flyer plate resulting in a repulsive force between the flyer plate and the coil. The flyer plate action lifts a valve seat, allowing high-pressure gas to flow from the valve plenum to the downstream (breech) location of the pellet or mechanical punch. All of the valve’s internal components are designed to operate in ITER-level static background magnetic fields. Here, a study was conducted to optimize the downstream pressure response for a range of valve sizes and operating pressures. In particular, the study analyzes the breech pressure response associated with varying plenum pressures as well as varying breech volumes. A computational fluid dynamics simulation was built in STAR-CCM+ and validated against data from laboratory experiments. The resulting simulation outputs, in the form of downstream responses for a variety of initial plenum pressures and breech volumes, will be used as a complement to experimental data to ensure the pressure pulse is suitable for pellet survivability. These data, combined with studies on pellet shear strength and shock response, will be applied to optimization of overall operating parameters of the ITER SPI system.
High-pressure CO 2 permeation properties and stability of ceramic-carbonate dual-phase membranes
CO 2 permeation properties and stability of ceramic-carbonate dual-phase membranes at high pressures/temperatures are critical to their CO 2 separation and membrane reactor applications, but such data are not available in the literature. Here, this work aims to study the effect of high transmembrane pressure on CO 2 permeation flux and the stability of molten carbonate in the dual-phase samarium-doped ceria (SDC) and molten-carbonate (MC) membranes. Dead-end porous SDC tubular supports were made by a cold isostatic press (CIP)/sintering method with a low porosity (below 7%), and gas-tight SDC-MC membranes were prepared by direct infiltration of molten lithium and sodium carbonate mixture into SDC pores, with a MC volume fraction less than 7%. CO 2 permeation/separation tests were performed on the SDC-MC membranes using feed gas of equal molar CO 2 /N 2 mixture at feed pressures up to 15 atm and sweep gas of helium at 1 atm. CO 2 permeation flux for the SDC-MC membranes depends logarithmically on feed/permeate CO 2 pressure ratio in 660–810°C. The temperature dependence of CO 2 permeation shows activation energy of 30 kJ/mol. Due to the small MC volume fraction and hence low effective carbonate conductivity, CO 2 permeation of the SDC-MC membranes is dominated by the carbonate ionic conduction in the MC phase. The SDC-MC membranes remain in the same structure, morphology, and gas-tightness after CO 2 separation tests at high feed pressures and temperatures, showing high stability of SDC-MC membranes for high-temperature, high-pressure separation and chemical reaction applications.
Influence of fabrication on microstructure and heat affected zone width in weldments of nuclear reactor pressure vessel steel
Advanced manufacturing routes such as electron beam welding and powder metallurgy with hot isostatic pressing are increasingly used across energy and aerospace industries, where the reliable prediction of weld behavior and heat affected zone (HAZ) evolution is critical. This study examines how fabrication routes and post-weld heat treatments influence phase distribution, crystallite size, microstrain, and dislocation density in nuclear reactor pressure vessel steels using synchrotron X-ray diffraction (SXRD). Retained austenite occurs only in samples that did not undergo austenitization, whereas an austenitizing heat treatment fully eliminates retained austenite and produces a more uniform microstructure across the weldment in terms of phase fraction, dislocation density, and microstrain. The Rosenthal solution underestimates the HAZ width for powder metallurgy samples. A newly proposed modified Rosenthal solution, reducing density by accounting for porosity, matches the SXRD-measured HAZ width with a 0.65% error. Structure–property correlations reveal that dislocation density correlates strongly with nanohardness in homogenous microstructures, while in heterogenous weldments nanohardness is further influenced by the presence of dissimilar phase boundaries. These findings provide new insight into the thermal and microstructural response of powder metallurgy fabricated steels and offer a framework for optimizing welding procedures and heat treatments in advanced manufacturing applications.
Detection of thin film phase transformations at high-pressure and high-temperature in a diamond anvil cell
Abstract Quantifying how grain size and/or deviatoric stress impact (Mg,Fe) 2 SiO 4 phase stability is critical for advancing our understanding of subduction processes and deep-focus earthquakes. Here, we demonstrate that well-resolved X-ray diffraction patterns can be obtained on nano-grained thin films within laser-heated diamond anvil cells (DACs) at hydrostatic pressures up to 24 GPa and temperatures up to 2300 K. Combined with well-established literature processes for tuning thin film grain size, biaxial stress, and substrate identity, these results suggest that DAC-loaded thin films can be useful for determining how grain size, deviatoric stress, and/or the coexistence of other phases influence high-pressure phase stability. As such, this novel DAC-loaded thin film approach may find use in a variety of earth science, planetary science, solid-state physics, and materials science applications.
Pressure Evolution of Ultrafast Photocarrier Dynamics and Electron–Phonon Coupling in FeTe 0.5 Se 0.5
Understanding the coupling between electrons and phonons in iron chalcogenides FeTe x Se 1–x has remained a critical but arduous project in recent decades. The direct observation of the electron–phonon coupling effect through electron dynamics and vibrational properties has been lacking. Here, we report the first pressure-dependent ultrafast photocarrier dynamics and Raman scattering studies on an iron chalcogenide FeTe 0.5 Se 0.5 to explore the interaction between electrons and phonons in this unconventional superconductor. The lifetime of the excited electrons evidently decreases as the pressure increases from 0 to 2.2 GPa, and then increases with further compression. The vibrational properties of the A 1g phonon mode exhibit similar behavior, with a pronounced frequency reduction appearing at approximately 2.3 GPa. The dual evidence reveals the enhanced electron–phonon coupling strength with pressure in FeTe 0.5 Se 0.5 . Our results give an insight into the role of the electron–phonon coupling effect in iron-based superconductors.
Stability and distortion of fcc LaH 10 with path-integral molecular dynamics
The synthesis of the high-temperature superconductor LaH 10 requires pressures in excess of 100 GPa, wherein it adopts a face-centered cubic structure. Upon decompression, this structure undergoes a distortion, which still supports superconductivity, but with a lower critical temperature. Previous calculations have shown that quantum and anharmonic effects are necessary to stabilize the cubic structure, but have not resolved the low pressure distortion. Using large scale path-integral molecular dynamics enabled by a machine learned potential, we show that a rhombohedral distortion appears at sufficiently low pressures. Here, we also highlight the importance of quantum zero-point motion in stabilizing the cubic structure.
Calcined Polyethyleneimine Coated Optical Fibers for Distributed pH Monitoring at High Pressures and Temperatures
In the oil and gas, CO2 sequestration, H2 subsurface storage, and geothermal energy sectors, subsurface pH measurements are critical for monitoring the geochemical conditions and estimating potential corrosion rates of wellbore systems. Real-time pH measurements in these conditions are vital for detecting and predicting corrosion deterioration of wellbore components that may jeopardize the safety and continued operation of wellbore systems. Building off of earlier TiO2 based pH sensors and the known pH sensitivity of amine-based polymers, a coating based on the secondary amine polymer polyethyleneimine (PEI) was developed. The sensor coating was treated with a high temperature (500 °C) calcination procedure in air to convert it into a more stable oxidized coating capable of withstanding hot aqueous solutions without dissolving while retaining linear pH sensitivity from pH values between 2 and 11. The sensor performance was measured using optical transmission measurements in solutions of various pHs and using optical backscatter reflectometry for distributed pH sensing demonstration in wellbore-relevant pressures (up to 1000 psi) and temperatures (80 °C). A calibration curve with strong differentiation between acidic and alkaline pH was developed for both transmission-based and distributed pH measurements, using fixed wavelength transmission and integrated linear amplitude of backscattered light for distributed measurements.
Surviving Under Pressure: The Role of Solvent, Crystal Size, and Morphology During Pelletization of Metal–Organic Frameworks
As metal–organic frameworks (MOFs) gain traction for applications, such as hydrogen storage, it is essential to form the as-synthesized powder materials into shaped bodies with high packing densities to maximize their volumetric performance. Mechanical compaction, which involves compressing the materials at high pressure, has been reported to yield high monolith density but often results in a significant loss in accessible porosity. Herein, we sought to systematically control (1) crystal size, (2) solvation, and (3) compacting pressure in the pelletization process to achieve high packing density without compromising the porosity that makes MOFs functional. It was determined that solvation is the most critical factor among the three factors examined. Solvation that exceeds the pore volume prevents the framework from collapsing, allowing for porosity to be maintained through pelletization. Higher pelletization pressure results in higher packing density, with extensive loss of porosity being observed at a higher pressure if the solvation is below the pore volume. Lastly, we observed that the morphology and size of the MOF particles result in variation in the highest achievable packing efficiency, but these numbers (75%) are still greater than many existing techniques used to form MOFs. Furthermore, we concluded that the application of pressure through pelletization is a suitable and widely applicable technique for forming high-density MOF-monoliths.
Molecular Origin of Wettability Alteration of Subsurface Porous Media upon Gas Pressure Variations
Upon extraction/injection of a large quantity of gas from/into a subsurface system in shale gas production or carbon sequestration, the gas pressure varies remarkably, which may significantly change the wettability of porous media involved. Mechanistic understanding of such changes is critical for designing and optimizing a related subsurface engineering process. Using molecular dynamics simulations, in this work we have calculated the contact angle of a water droplet on various solid surfaces (kerogen, pyrophyllite, calcite, gibbsite, and montmorillonite) as a function of CO 2 or CH 4 gas pressure up to 200 atm at a temperature of 300 K. The calculation reveals a complex behavior of surface wettability alteration by gas pressure variation depending on surface chemistry and structure, and molecular interactions of fluid molecules with surfaces. As the CO 2 gas pressure increases, a partially hydrophilic kerogen surface becomes highly hydrophobic, while a calcite surface becomes more hydrophilic. Considering kerogen and calcite being the major components of a shale formation, we postulate that the wettability alteration of a solid surface induced by a gas pressure change may play an important role in fluid flows in shale gas production and geological carbon sequestration.
A workflow to assess the efficacy of brine extraction for managing injection-induced seismicity potential using data from a CO 2 injection site near Decatur, Illinois
Injection of CO 2 for storage in a geologic formation increases pore pressure and alters in situ stresses. Depending on the orientation of any existing fault and fracture planes, such as critically stressed planes, this stress alteration will modify normal stresses acting on planes and could result in frictional sliding and release stored energy in the form of seismicity. Brine extraction (BE) is a technique that can be applied prior to, or during, CO 2 injection to reduce pore pressure for increasing storage capacity and, potentially, for reducing the likelihood of frictional sliding. Here a workflow is described to assess the efficacy of BE for mitigating frictional sliding (i.e., seismicity) during injection and entails: site characterization, stress calculations and failure assessment, static and dynamic modeling, and BE operational planning. Site characterization describes the stress field used to calculate the Coulomb Failure Function (CFF) that constrains allowable pore pressure changes and injection rates in the numerical simulation of CO 2 injection scenarios. The inclusion of BE in the workflow allows for determination of the potential need for pressure reduction, and evaluation of the effectiveness of this operation. Example application of the workflow using an injection field dataset near Decatur, IL, provides insight on fracture planes and stresses at the site, formation properties and the impact of variable CO 2 injection-rate targets on whether BE plans are required. The study workflow indicates that BE could enhance CO 2 injection rate by 39% and correspondingly reduce the potential for injection-induced seismicity as indicated by a reduction in CFF.