SEARCH · Search NASA

Results for “Commonality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Comparison of the NASA Common Research Model European Transonic Wind Tunnel Test Data to NASA Test Data

Experimental aerodynamic investigations of the NASA Common Research Model have been conducted in the NASA Langley National Transonic Facility, the NASA Ames 11-ft wind tunnel, and the European Transonic Wind Tunnel. In the NASA Ames 11-ft wind tunnel, data have been obtained at only a chord Reynolds number of 5 million for a wing/body/tail = 0 degree incidence configuration. Data have been obtained at chord Reynolds numbers of 5, 19.8 and 30 million for the same configuration in the National Transonic Facility and in the European Transonic Facility. Force and moment, surface pressure, wing bending and twist, and surface flow visualization data were obtained in all three facilities but only the force and moment and surface pressure data are presented herein.

Rivers, Melissa↗

NASA NTRS2016

Computational Investigation of a Boundary-Layer Ingesting Propulsion System for the Common Research Model

The present paper examines potential propulsive and aerodynamic benefits of integrating a Boundary-Layer Ingestion (BLI) propulsion system into a typical commercial aircraft using the Common Research Model (CRM) geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment is used to generate engine conditions for CFD analysis. Improvements to the BLI geometry are made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method, and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2 deg for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.4% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from Boundary-Layer Ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.

Blumenthal, Brennan T.↗

NASA NTRS2016

Evolution in Metadata Quality: Common Metadata Repository's Role in NASA Curation Efforts

Metadata Quality is one of the chief drivers of discovery and use of NASA EOSDIS (Earth Observing System Data and Information System) data. Issues with metadata such as lack of completeness, inconsistency, and use of legacy terms directly hinder data use. As the central metadata repository for NASA Earth Science data, the Common Metadata Repository (CMR) has a responsibility to its users to ensure the quality of CMR search results. This poster covers how we use humanizers, a technique for dealing with the symptoms of metadata issues, as well as our plans for future metadata validation enhancements. The CMR currently indexes 35K collections and 300M granules.

metadata quality↗

NASA NTRS2017

Computational Fluid Dynamic Analyses for the High-Lift Common Research Model Using the USM3D and FUN3D Flow Solvers

Two Navier-Stokes codes were used to compute flow over the High-Lift Common Research Model (HL-CRM) in preparation for a wind tunnel test to be performed at the NASA Langley Research Center 14-by-22-Foot Subsonic Tunnel in fiscal year 2018. Both flight and wind tunnel conditions were simulated by the two codes at set Mach numbers and Reynolds numbers over a full angle-of-attack range for three configurations: cruise, landing and takeoff. Force curves, drag polars and surface pressure contour comparisons are shown for the two codes. The lift and drag curves compare well for the cruise configuration up to 10deg angle of attack but not as well for the other two configurations. The drag polars compare reasonably well for all three configurations. The surface pressure contours compare well for some of the conditions modeled but not as well for others.

Rivers, Melissa↗

NASA NTRS2017

Cross-Cutting Risk Framework: Mining Data for Common Risks Across the Portfolio

The National Aeronautics and Space Administration (NASA) defines risk management as an integrated framework, combining risk-informed decision making and continuous risk management to foster forward-thinking and decision making from an integrated risk perspective. Therefore, decision makers must have access to risks outside of their own project to gain the knowledge that provides the integrated risk perspective. Through the Goddard Space Flight Center (GSFC) Flight Projects Directorate (FPD) Business Change Initiative (BCI), risks were integrated into one repository to facilitate access to risk data between projects. With the centralized repository, communications between the FPD, project managers, and risk managers improved and GSFC created the cross-cutting risk framework (CCRF) team. The creation of the consolidated risk repository, in parallel with the initiation of monthly FPD risk managers and risk governance board meetings, are now providing a complete risk management picture spanning the entire directorate. This paper will describe the challenges, methodologies, tools, and techniques used to develop the CCRF, and the lessons learned as the team collectively worked to identify risks that FPD programs projects had in common, both past and present.

risk-informed decision making↗

NASA NTRS2017

Comparison of Commonly-Used Microwave Radiative Transfer Models for Snow Remote Sensing

This paper reviews four commonly-used microwave radiative transfer models that take different electromagnetic approaches to simulate snow brightness temperature (T(sub B)): the Dense Media Radiative Transfer - Multi-Layer model (DMRT-ML), the Dense Media Radiative Transfer - Quasi-Crystalline Approximation Mie scattering of Sticky spheres (DMRT-QMS), the Helsinki University of Technology n-Layers model (HUT-nlayers) and the Microwave Emission Model of Layered Snowpacks (MEMLS). Using the same extensively measured physical snowpack properties, we compared the simulated T(sub B) at 11, 19 and 37 GHz from these four models. The analysis focuses on the impact of using different types of measured snow microstructure metrics in the simulations. In addition to density, snow microstructure is defined for each snow layer by grain optical diameter (Do) and stickiness for DMRT-ML and DMRT-QMS, mean grain geometrical maximum extent (D(sub max)) for HUT n-layers and the exponential correlation length for MEMLS. These metrics were derived from either in-situ measurements of snow specific surface area (SSA) or macrophotos of grain sizes (D(sub max)), assuming non-sticky spheres for the DMRT models. Simulated T(sub B) sensitivity analysis using the same inputs shows relatively consistent T(sub B) behavior as a function of Do and density variations for the vertical polarization (maximum deviation of 18 K and 27 K, respectively), while some divergences appear in simulated variations for the polarization ratio (PR). Comparisons with ground based radiometric measurements show that the simulations based on snow SSA measurements have to be scaled with a model-specific factor of Do in order to minimize the root mean square error (RMSE) between measured and simulated T(sub B). Results using in-situ grain size measurements (SSA or D(sub max), depending on the model) give a mean T(sub B) RMSE (19 and 37 GHz) of the order of 16-26 K, which is similar for all models when the snow microstructure metrics are scaled. However, the MEMLS model converges to better results when driven by the correlation length estimated from in-situ SSA measurements rather than D(sub max) measurements. On a practical level, this paper shows that the SSA parameter, a snow property that is easy to retrieve in-situ, appears to be the most relevant parameter for characterizing snow microstructure, despite the need for a scaling factor.

Snow↗

NASA NTRS2017

Noise Simulations of the High-Lift Common Research Model

The PowerFLOW(TradeMark) code has been used to perform numerical simulations of the high-lift version of the Common Research Model (HL-CRM) that will be used for experimental testing of airframe noise. Time-averaged surface pressure results from PowerFLOW(TradeMark) are found to be in reasonable agreement with those from steady-state computations using FUN3D. Surface pressure fluctuations are highest around the slat break and nacelle/pylon region, and synthetic array beamforming results also indicate that this region is the dominant noise source on the model. The gap between the slat and pylon on the HL-CRM is not realistic for modern aircraft, and most nacelles include a chine that is absent in the baseline model. To account for those effects, additional simulations were completed with a chine and with the slat extended into the pylon. The case with the chine was nearly identical to the baseline, and the slat extension resulted in higher surface pressure fluctuations but slightly reduced radiated noise. The full-span slat geometry without the nacelle/pylon was also simulated and found to be around 10 dB quieter than the baseline over almost the entire frequency range. The current simulations are still considered preliminary as changes in the radiated acoustics are still being observed with grid refinement, and additional simulations with finer grids are planned.

Lockard, David P.↗

NASA NTRS2017

Harvesting NASA's Common Metadata Repository (CMR)

As part of NASA's Earth Observing System Data and Information System (EOSDIS), the Common Metadata Repository (CMR) stores metadata for over 30,000 datasets from both NASA and international providers along with over 300M granules. This metadata enables sub-second discovery and facilitates data access. While the CMR offers a robust temporal, spatial and keyword search functionality to the general public and international community, it is sometimes more desirable for international partners to harvest the CMR metadata and merge the CMR metadata into a partner's existing metadata repository. This poster will focus on best practices to follow when harvesting CMR metadata to ensure that any changes made to the CMR can also be updated in a partner's own repository. Additionally, since each partner has distinct metadata formats they are able to consume, the best practices will also include guidance on retrieving the metadata in the desired metadata format using CMR's Unified Metadata Model translation software.

Earth Resources↗

NASA NTRS2018

Air Traffic Management Technology Demonstration - 3 (ATD-3) Multi-Flight Common Route (MFCR) Concept of Operations Version 1.0

NASA's Multi Flight Common Route (MFCR) automation represents one element of those technologies focusing primarily on delay recovery in the en route phase of flight. Delay recovery is an attenuation of flight-time delay, accomplished by periodically revising weather-avoidance routing as the convective weather system evolves. MFCR is intended for use by Traffic Management Coordinators (TMCs) in Air Route Traffic Control Centers (ARTCCs, or Centers) and traffic management specialists (TMSs) in the Air Traffic Control System Command Center (ATCSCC). MFCR leverages existing weather, airspace, and traffic data, as well as improvements in navigation, surveillance, communication, and digital information technologies, to build on existing ATM automation and address some of the shortcomings associated with strategic traffic flow management initiatives and weather forecasting uncertainties. These capabilities provide significant potential benefits in the form of time, fuel, and cost savings. The concept of operations described in this document describes MFCR functionality as delivered by NASA to the FAA in December 2017, including a list of potential enhancements that may be realized when the system is fielded.

conops↗

NASA NTRS2018

Common-Mode Digital Holographic Microscope

A lens-less digital holographic microscope, a reflective digital holographic microscope, and a digital holographic microscope including a plurality of lenses. In one example, the digital holographic microscope includes a single mode fiber collimated light source which provides illumination for both the `science` and `reference` arms, a pair of microscope objectives located side-by side, and illuminated by the common beam, a relay lens whose center is between the two objectives, and a focal plane element where the interference pattern is measured.

Wallace, James K.↗

NASA NTRS2019

Multi-Objective Optimal Control of the 6-DoF Aeroservoelastic Common Research Model with Aspect Ratio 13.5 Wing

A new 6-DoF aeroservoelastic (ASE) Common Research Model (CRM) provided by The Boeing Company with aspect ratio 13.5 and 17 control surfaces per wing is utilized to demonstrate combined tracking and optimal multi-objective control. The multi-objective controller is derived on the closed loop tracking controller, and utilizes state and gust estimates provided by an extended state observer. Various methods of model reduction useful for control and estimation are presented. A computationally efficient MATLAB/Simulink simulation is presented which includes actuator dynamics, rate and deflection saturation limits, and gust disturbance inputs. The platform is used to demonstrate excellent 6-DoF tracking control performance coupled with the multi-objective controller, which is shown to effectively reduce structural mode movement, wing root bending moment, and drag. State and gust estimation is also shown to perform well, even when derived and/or implemented with significantly fewer states than the original full-sized model.

Drew, Michael C.↗

NASA NTRS2018

A Common Probe Design for Multiple Planetary Destinations

Atmospheric probes have been successfully flown to planets and moons in the solar system to conduct in situ measurements. They include the Pioneer Venus multi-probes, the Galileo Jupiter probe, and Huygens probe. Probe mission concepts to five destinations, including Venus, Jupiter, Saturn, Uranus, and Neptune, have all utilized similar-shaped aeroshells and concept of operations, namely a 45° sphere cone shape with high density heatshield material and parachute system for extracting the descent vehicle from the aeroshell. The current paradigm is to design a probe to meet specific mission requirements and to optimize mass, volume, and cost for a single mission. However, this methodology means repeated efforts to design an aeroshell for different destinations with minor differences. A new paradigm has been explored that has a “common probe” design that could be flown at these different destinations and could be assembled in advance with multiple copies, properly stored, and made available for future NASA missions. Not having to re-design and rebuild an aeroshell could potentially result in cost and schedule savings and reduce the risk of losing technologies and skills difficult to sustain over decades.

Hwang, Helen H.↗

NASA NTRS2018

A Common Probe Design for Multiple Planetary Destinations

Introduction: Atmospheric probes have been successfully flown to planets and moons in the solar system to conduct in situ measurements. They include the Pioneer Venus multiprobes, the Galileo Jupiter probe, and Huygens probe. Probe mission concepts to five destinations, including Venus, Jupiter, Saturn, Uranus, and Neptune, have all utilized similarshaped aeroshells and concept of operations, namely a 45° sphere cone shape with high density heatshield material and parachute system for extracting the descent vehicle from the aeroshell. The current paradigm is to design a probe to meet specific mission requirements and to optimize mass, volume, and cost for a single mission. However, this methodology means repeated efforts to design an aeroshell for different destinations with minor differences. A new paradigm has been explored that has a "common probe" design that could be flown at these different destinations and could be assembled in advance with multiple copies, properly stored, and made available for future NASA missions.

Hwang, Helen H.↗

NASA NTRS2016

Effect of Solar Array Plume Interactions on Hall Thruster Cathode Common Potentials

In typical implementations of spacecraft electric propulsion (EP) systems the electrical ground of the EP power processing units are resistively isolated from the main spacecraft electrical ground. Telemetry measuring the potential difference between EP power processing unit and the spacecraft electrical ground is usually referred to as the “cathode common” potential. In this paper we review flight and laboratory data on natural and EP generated plasma interactions with solar arrays, present the theory of spacecraft floating potentials, show how this theory is consistent with flight data, and extend this theory to spacecraft with high power Hall effect thrusters.

Katz, Ira↗

NASA NTRS2019

An Evaluation and Recommendations for Further CFD Research Based on the NASA Common Research Model (CRM) Analysis from the AIAA Drag Prediction Workshop (DPW) Series

The six Drag Prediction Workshops (DPW) have drawn a total of 125 participants submitting 225 data entries. Over half of these occurred in the last three workshops dealing with the NASA Common Research Model (CRM). Participants have ranged from North America, Europe, Asia, and South America, representing Government, Industry, Academia, and Commercial/Vendors. The DPW Series has generated a tremendous amount of CFD data, freely available to the public domain. A continuous improvement of the results as measured by: the reduction of the spread of drag predictions for the specified “nominal” cruise point, accuracy of drag increment, and the angle-of-attack sweep behavior, has been noted. Although it has been difficult separating out the parts and pieces that contribute to errors in CFD drag predictions, part of the improvements over the years can be attributed to grid resolution. The scatter in predicted drag in the continuum has been reduced dramatically from plus or minus 50 counts in DPW-I to around plus or minus 5 counts for DPW-V and - VI. During the six workshops, the grid size has grown dramatically. The average size of the medium wing-body meshes in DPW-I through DPW-IV have been 3.2, 5.4, 7.8 and 10.9 million, respectively. This represents a growth rate of approximately 17 percent per year during the eight years between DPW-I and DPW-IV. For DPW-VI, this number has grown from 25 to 50 million points for the various families of grids available. The finest level grids have increased steadily, from just over 3 million grid points in DPW-I to 225 million for the WBNP (Wing-Body-Nacelle-Pylon) in DPW-VI. While progress has been made, persistent problems with grid generation and separated flow prediction continue. The experiences and recommendations presented here are consistent with those espoused in the “CFD Vision 2030 Study: A Path to Revolutionary Computational Aerosciences,” NASA/CR-2014-218178.

Tinoco, Edward N.↗

NASA NTRS2017

Compendium of Single Event Transient (SET) and Total Ionizing Dose (TID) Test Results for Commonly Used Voltage Comparators

This data compendium reports single event transient (SET) and total ionizing dose (TID) test results for commonly used commercial-off-the-shelf (COTS) and radiation hardened voltage comparators targeted for possible use in space-based missions. Interesting trends in the variability of the radiation performance of these devices due to differences in lot date codes, manufacturers, circuit design, and test conditions are analyzed herein.

Bozovich, Amanda↗

NASA NTRS2018

A Qualitative Study on the Effects of Mesh Guideline Modification for Unstructured Mesh Generation of the NASA High Lift Common Research Model (HL-CRM)

As part of the 1st Geometry and Mesh Generation Workshop, unstructured tetrahedral and unstructured hybrid Computational Fluid Dynamics meshes were generated according to the meshing guidelines supplied by the 3rd High Lift Prediction Workshop. During this process, it was noted that application of some meshing guidelines became a bottleneck in the process and negatively impacted the quality of the meshes. A study is performed to compare the FUN3D simulation from the baseline medium-resolution workshop unstructured mesh with those on meshes resulting from guideline variations to the baseline. Recommendations on the elimination or reduction of meshing guidelines for high lift aerodynamic cases like the High Lift Common Research Model are based on the resulting data.

Jones, William T.↗

NASA NTRS2019

Experimental Investigation of the NASA Common Research Model with a Natural Laminar Flow Wing in the NASA Langley National Transonic Facility

A test of the new NASA Common Research Model with a Natural Laminar Flow (CRMNLF) semispan wing in the NASA Langley National Transonic Facility (NTF) was completed in October 2018. The main focus of this test was the evaluation of the extent of laminar flow on the CRM-NLF wing at various Reynolds numbers and test conditions. During this test, data were acquired at chord Reynolds numbers from 10 to 30 million and at Mach numbers ranging from 0.84 to 0.86. This investigation provided valuable insight into the necessary procedures for laminar flow testing in the NTF. It also significantly advanced the new carbonbased heating layer technique to improve the quality of transition visualization data from temperature sensitive paint (TSP) in a cryogenic wind tunnel.

Rivers, Melissa B.↗