SEARCH · Search NASA

Results for “Computer Terminals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Computer graphics application in the engineering design integration system

The computer graphics aspect of the Engineering Design Integration (EDIN) system and its application to design problems were discussed. Three basic types of computer graphics may be used with the EDIN system for the evaluation of aerospace vehicles preliminary designs: offline graphics systems using vellum-inking or photographic processes, online graphics systems characterized by direct coupled low cost storage tube terminals with limited interactive capabilities, and a minicomputer based refresh terminal offering highly interactive capabilities. The offline line systems are characterized by high quality (resolution better than 0.254 mm) and slow turnaround (one to four days). The online systems are characterized by low cost, instant visualization of the computer results, slow line speed (300 BAUD), poor hard copy, and the early limitations on vector graphic input capabilities. The recent acquisition of the Adage 330 Graphic Display system has greatly enhanced the potential for interactive computer aided design.

Glatt, C. R.↗

NASA NTRS1977

The 5th Meeting of the Ad Hoc Panel on Terminal Configured Vehicles

A report of the fifth meeting of the NASA Research and Technology Advisory Council, Ad Hoc panel on Terminal Configured Vehicles is presented. Some of the following topics were discussed; (1) microwave landing systems; (2) whole word computer system status; (3) flight path angle control: (4) VTOL approaches and landing technology; and (5) simulation study in wind shear.

Source record↗

NASA NTRS1986

Algorithm for Fuel-Conservative Airplane Descents

Federal Aviation Administration implementing automated, time-based metering form of air-traffic control (ATC) with profile-descent procedures for arrivals into terminal area. Measures provide fuel savings by matching arrival of airplanes to airport acceptance rate through time-control computations and allowing pilot to descend at his discretion from cruise altitude to designated metering-fix altitude in idle-thrust clean configuration. Airborne descent algorithm developed compatible with time-based metering and profile-descent procedures and designed to improve accuracy of delivering airplane during fuel-efficient descent to metering fix at time designated by the ATC system.

Knox, C. E.↗

NASA NTRS1987

Analysis of the tapered slot antenna

A method for calculating the radiation pattern of end-fire tapered slot antennas with or without dielectric substrate is presented. The method involves a two-step procedure: (1) determine the field distribution of a traveling wave along the tapered slot, and (2) compute the radiation from this slot field by using the half-plane Green's function to account for termination effects. Acceptable estimates of the slot field usually can be obtained from a stepped approximation to the tapered geometry. The method has been verified by comparisons to measured patterns for various dielectric substrates and antenna dimensions. However, the effect of lateral truncation has not yet been successfully modeled. Experimental patterns showing this effect are presented.

Janaswamy, Ramakrishna↗

NASA NTRS1991

Estimating Rain Attenuation In Satellite Communication Links

Attenuation computed with help of statistical model and meteorological data. NASA Lewis Research Center Satellite Link Attenuation Model (SLAM) program QuickBASIC computer program evaluating static and dynamic statistical assessment of impact of rain attenuation on communication link established between Earth terminal and geosynchronous satellite. Application in specification, design, and assessment of satellite communication links for any terminal location in continental United States. Written in Microsoft QuickBASIC.

Manning, R. M.↗

NASA NTRS1993

A prototype to automate the video subsystem routing for the video distribution subsystem of Space Station Freedom

The Video Distribution Subsystem (VDS) for Space Station Freedom provides onboard video communications. The VDS includes three major functions: external video switching; internal video switching; and sync and control generation. The Video Subsystem Routing (VSR) is a part of the VDS Manager Computer Software Configuration Item (VSM/CSCI). The VSM/CSCI is the software which controls and monitors the VDS equipment. VSR activates, terminates, and modifies video services in response to Tier-1 commands to connect video sources to video destinations. VSR selects connection paths based on availability of resources and updates the video routing lookup tables. This project involves investigating the current methodology to automate the Video Subsystem Routing and developing and testing a prototype as 'proof of concept' for designers.

Betz, Jessie M. Bethly↗

NASA NTRS2004

Effects of an Approach Spacing Flight Deck Tool on Pilot Eyescan

Oseguera-Lohr, Rosa M.↗

NASA NTRS2002

Evaluation of Operational Procedures for Using a Time-Based Airborne Inter-arrival Spacing Tool

An airborne tool has been developed based on the concept of an aircraft maintaining a time-based spacing interval from the preceding aircraft. The Advanced Terminal Area Approach Spacing (ATAAS) tool uses Automatic Dependent Surveillance-Broadcast (ADS-B) aircraft state data to compute a speed command for the ATAAS-equipped aircraft to obtain a required time interval behind another aircraft. The tool and candidate operational procedures were tested in a high-fidelity, full mission simulator with active airline subject pilots flying an arrival scenario using three different modes for speed control. The objectives of this study were to validate the results of a prior Monte Carlo analysis of the ATAAS algorithm and to evaluate the concept from the standpoint of pilot acceptability and workload. Results showed that the aircraft was able to consistently achieve the target spacing interval within one second (the equivalent of approximately 220 ft at a final approach speed of 130 kt) when the ATAAS speed guidance was autothrottle-coupled, and a slightly greater (4-5 seconds), but consistent interval with the pilot-controlled speed modes. The subject pilots generally rated the workload level with the ATAAS procedure as similar to that with standard procedures, and also rated most aspects of the procedure high in terms of acceptability. Although pilots indicated that the head-down time was higher with ATAAS, the acceptability of head-down time was rated high. Oculometer data indicated slight changes in instrument scan patterns, but no significant change in the amount of time spent looking out the window between the ATAAS procedure versus standard procedures.

Oseguera-Lohr, Rosa M.↗

NASA NTRS1993

A class of hybrid finite element methods for electromagnetics: A review

Integral equation methods have generally been the workhorse for antenna and scattering computations. In the case of antennas, they continue to be the prominent computational approach, but for scattering applications the requirement for large-scale computations has turned researchers' attention to near neighbor methods such as the finite element method, which has low O(N) storage requirements and is readily adaptable in modeling complex geometrical features and material inhomogeneities. In this paper, we review three hybrid finite element methods for simulating composite scatterers, conformal microstrip antennas, and finite periodic arrays. Specifically, we discuss the finite element method and its application to electromagnetic problems when combined with the boundary integral, absorbing boundary conditions, and artificial absorbers for terminating the mesh. Particular attention is given to large-scale simulations, methods, and solvers for achieving low memory requirements and code performance on parallel computing architectures.

Volakis, J. L.↗

NASA NTRS1993

A laboratory system for the investigation of rain fade compensation techniques for Ka-band satellites

The design and performance of a rain fade simulation/counteraction system on a laboratory simulated 30/20 GHz, time division multiple access (TDMA) satellite communications testbed is evaluated. Severe rain attenuation of electromagnetic radiation at 30/20 GHz occurs due to the carrier wavelength approaching the water droplet size. Rain in the downlink path lowers the signal power present at the receiver, resulting in a higher number of bit errors induced in the digital ground terminal. The laboratory simulation performed at NASA Lewis Research Center uses a programmable PIN diode attenuator to simulate 20 GHz satellite downlink geographic rain fade profiles. A computer based network control system monitors the downlink power and informs the network of any power threshold violations, which then prompts the network to issue commands that temporarily increase the gain of the satellite based traveling wave tube (TWT) amplifier. After the rain subsides, the network returns the TWT to the normal energy conserving power mode. Bit error rate (BER) data taken at the receiving ground terminal serves as a measure of the severity of rain degradation, and also evaluates the extent to which the network can improve the faded channel.

Svoboda, James S.↗

NASA NTRS1978

Computerized power supply analysis: State equation generation and terminal models

To aid engineers that design power supply systems two analysis tools that can be used with the state equation analysis package were developed. These tools include integration routines that start with the description of a power supply in state equation form and yield analytical results. The first tool uses a computer program that works with the SUPER SCEPTRE circuit analysis program and prints the state equation for an electrical network. The state equations developed automatically by the computer program are used to develop an algorithm for reducing the number of state variables required to describe an electrical network. In this way a second tool is obtained in which the order of the network is reduced and a simpler terminal model is obtained.

Garrett, S. J.↗

NASA NTRS1982

Use of interactive graphics to analyze QUICK-geometry: Supplement

The advantages of using interactive computer graphics to display aircraft geometry to aid in detection and analysis of errors are described. The QUICK geometry system is reviewed and the Quick Interactive Graphics Analysis (QUIAGA) program is described. This QUIAGA program was developed to exercise the QUICK geometry subroutines to examine in several modes on a graphics terminal. Its use in the detection and analysis of errors in the QUICK geometry definition can be of great assistance in speedily arriving at a correct analytical geometry description for flow field computation. Experience with the program in developing a QUICK geometry model of the NASA Space Shuttle Orbiter is used to show some of its features. Appendixes giving details of program usage and an example session are included.

Townsend, J. C.↗

NASA NTRS1973

Liquid rocket propellant feedline dynamics

An analytical and experimental study of liquid rocket propellant feedline dynamics has been performed. The analytical model, which includes the effects of turbulent flow, distributed and local compliances, bellows, side branches, and structural mounting stiffness, was verified by an experimental program. Water was used as the internal fluid and the dynamic perturbations in pressure and flow were created by a piston pulser. Measurements were made to determine the pressure perturbation amplitude and phase at the line terminal due to a sinusoidal pulser excitation. The frequency response of the various line configurations tested were compared with the computed theoretical results.

Holster, J. L.↗

NASA NTRS1979

Operator performance and localized muscle fatigue in a simulated space vehicle control task

Fourier transforms in a special purpose computer were utilized to obtain power spectral density functions from electromyograms of the biceps brachii, triceps brachii, brachioradialis, flexor carpi ulnaris, brachialis, and pronator teres in eight subjects performing isometric tracking tasks in two directions utilizing a prototype spacecraft rotational hand controller. Analysis of these spectra in general purpose computers aided in defining muscles involved in performing the task, and yielded a derived measure potentially useful in predicting task termination. The triceps was the only muscle to show significant differences in all possible tests for simple effects in both tasks and, overall, was the most consistently involved of the six muscles. The total power monitored for triceps, biceps, and brachialis dropped to minimal levels across all subjects earlier than for other muscles. However, smaller variances existed for the biceps, brachioradialis, brachialis, and flexor carpi ulnaris muscles and could provide longer predictive times due to smaller standard deviations for a greater population range.

Lewis, J. L., Jr.↗

NASA NTRS1980

Iterative solutions for one-dimensional diffusion with time varying surface composition and composition-dependent diffusion coefficient

Solutions are given for one-dimensional diffusion problems with a time varying surface composition and also a composition dependent diffusion coefficient. The most general solution does not require special mathematical functions to fit the variation in surface composition or D(C). In another solution, a series expansion may be used to fit the time dependent surface concentration. These solutions make use of iterative calculations that converge rapidly and are highly stable. Computer times are much shorter than that required for finite difference calculations and can efficiently make use of interactive graphics terminals. Existing gas carburization data were used to provide an illustration of an iterative approach with a time varying carbon composition at the free surface.

Chow, M.↗

NASA NTRS1981

Television broadcast from space systems: Technology, costs

Broadcast satellite systems are described. The technologies which are unique to both high power broadcast satellites and small TV receive-only earth terminals are also described. A cost assessment of both space and earth segments is included and appendices present both a computer model for satellite cost and the pertinent reported experience with the Japanese BSE.

Cuccia, C. L.↗

NASA NTRS1990

Freedom Station wall design using hydrodynamic modelling

The paper outlines selected outputs from an ongoing Marshall Space Flight Center/US Army Corps of Engineers parametric study of the effects of meteoroid/space debris impacts on Space Station Freedom module wall protection structures. The advantages and limitations of HULL hydrocode computer simulation are discussed, and examples of meteoroid/ debris impacts on various wall structural designs are presented. Trends in the terminal effects of particle sizes, velocities, shapes, and impact angles upon structural design parameters (wall and bumper thickness and spacing) are summarized and depicted through selected simulation runs. Throughout the paper, proposed structural modifications to the baseline module protection structure will be examined which are capable of mitigating damage from particle impacts.

Williamsen, Joel E.↗

NASA NTRS2018

Dual Rotating Rake Measurements of Higher-Order Duct Modes: Validation Using Experimental and Numerical Data

A rotating rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. After analysis of the measured data, the mode coefficient amplitudes and phases were quantified. Early studies using this system found that mode power levels computed from rotating rake measured data would agree with the far-field power levels. However, this agreement required that the sound from the noise sources within the duct propagated outward from the duct exit without reflection and previous studies suggested conditions could exist where significant reflections could occur. This paper shows that mounting a second rake to the rotating system, with an offset in both the axial and the azimuthal directions, measures the data necessary to determine the modes propagating in both directions within a duct. The rotating rake data analysis technique was extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode coefficients at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode coefficients for the modes propagating in both directions within the duct while accounting for the presence of evanescent modes. The validation of the dual-rotating-rake measurements was conducted using data from a combination of experiments and numerical calculations to compute reflection coefficients and other mode coefficient ratios. Compared to results from analytical and numerical computations, the results from dual-rotating-rake measured data followed the expected trends when frequency, mode number, and duct termination geometry were changed.

Validation↗