Search NASA⌕ Search

SEARCH · Search NASA

Results for “DIFFUSION EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

The chemistry and diffusion of aircraft exhausts in the lower stratosphere during the first few hours after fly-by

An analysis of the hydrogen-nitrogen-oxygen reaction systems in the lower stratosphere as they are initially perturbed by individual aircraft engine exhaust plumes was conducted in order to determine whether any significant chemical reactions occur, either among exhaust chemical species, or between these species and the environmental ozone, while the exhaust products are confined to intact plume segments at relatively high concentrations. The joint effects of diffusive mixing and chemical kinetics on the reactions were also studied, using the techniques of second-order closure diffusion/chemistry models. The focus of the study was on the larger problem of the potential depletion of ozone by supersonic transport aircraft exhaust materials emitted into the lower stratosphere.

Hilst, G. R.↗

Numerical modeling of HgCdTe solidification: Effects of phase diagram, double-diffusion convection and microgravity level

A numerical model of HgCdTe solidification was implemented using finite the element code FIDAP. Model verification was done using both experimental data and numerical test problems. The model was used to evaluate possible effects of double-diffusion convection in molten material, and microgravity level on concentration distribution in the solidified HgCdTe. Particular attention was paid to incorporation of HgCdTe phase diagram. It was found, that below a critical microgravity amplitude, the maximum convective velocity in the melt appears virtually independent on the microgravity vector orientation. Good agreement between predicted interface shape and an interface obtained experimentally by quenching was achieved. The results of numerical modeling are presented in the form of video film.

Bune, Andris V.↗

Solar Wind Implantation into Lunar Regolith: Hydrogen Retention in a Surface with Defects

Solar wind protons are implanted directly into the top 100 nm of the lunar near-surface region, but can either quickly diffuse out of the surface or be retained, depending upon surface temperature and the activation energy, U, associated with the implantation site. In this work, we explore the distribution of activation energies upon implantation and the associated hydrogen-retention times; this for comparison with recent observation of OH on the lunar surface. We apply a Monte Carlo approach: for simulated solar wind protons at a given local time, we assume a distribution of U values with a central peak, U(sub c) and width, U(sub w), and derive the fraction retained for long periods in the near-surface. We find that surfaces characterized by a distribution with predominantly large values of U (greater than 1 eV) like that expected at defect sites will retain implanted H (to likely form OH). Surfaces with the distribution predominantly at small values of U (less than 0.2 eV) will quickly diffuse away implanted H. However, surfaces with a large portion of activation energies between 0.3 eV less than U less than 0.9 eV will tend to be H-retentive in cool conditions but transform into H-emissive surfaces when warmed (as when the surface rotates into local noon). These mid-range activation energies give rise to a diurnal effect with diffusive loss of H at noontime.

regolith↗

Zero-gravity aerosol behavior

The feasibility and scientific benefits of a zero gravity aerosol study in an orbiting laboratory were examined. A macroscopic model was devised to deal with the simultaneous effects of diffusion and coagulation of particles in the confined aerosol. An analytical solution was found by treating the particle coagulation and diffusion constants as ensemble parameters and employing a transformation of variables. The solution was used to carry out simulated zero gravity aerosol decay experiments in a compact cylindrical chamber. The results demonstrate that the limitations of physical space and time imposed by the orbital situation are not prohibitive in terms of observing the history of an aerosol confined under zero gravity conditions. While the absence of convective effects would be a definite benefit for the experiment, the mathematical complexity of the problem is not greatly reduced when the gravitational term drops out of the equation. Since the model does not deal directly with the evolution of the particle size distribution, it may be desirable to develop more detailed models before undertaking an orbital experiment.

Edwards, H. W.↗

Interstellar cyanogen and the temperature of the cosmic microwave background radiation

We present the results of a recently completed effort to determine the amount of CN rotational excitation in five diffuse interstellar clouds for the purpose of accurately measuring the temperature of the cosmic microwave background radiation (CMBR). In addition, we report a new detection of emission from the strongest hyperfine component of the 2.64 mm CN rotational transition (N = 1-0) in the direction toward HD 21483. We have used this result in combination with existing emission measurements toward our other stars to correct for local excitation effects within diffuse clouds which raise the measured CN rotational temperature above that of the CMBR. After making this correction, we find a weighted mean value of T(CMBR) = 2.729 (+0.023, -0.031) K. This temperature is in excellent agreement with the new COBE measurement of 2.726 +/- 0.010 K (Mather et al., 1993). Our result, which samples the CMBR far from the near-Earth environment, attests to the accuracy of the COBE measurement and reaffirms the cosmic nature of this background radiation. From the observed agreement between our CMBR temperature and the COBE result, we conclude that corrections for local CN excitation based on millimeter emission measurements provide an accurate adjustment to the measured rotational excitation.

Roth, Katherine C.↗

Nonlinear restrictions on dynamo action

Astrophysical dynamos operate in the limit of small magnetic diffusivity. In order for magnetic reconnection to occur, very small magnetic structures must form so that diffusion becomes effective. The formation of small-scale fields is accompanied by the stretching of the field lines and therefore by an amplification of the magnetic field strength. The back reaction of the magnetic field on the motions leads to the eventual saturation of the dynamo process, thus posing a constraint on the amount of magnetic flux that can be generated by dynamo action, It is argued that in the limit of small diffusivity only a small amount of flux, many orders of magnitude less than the observed fluxes, can be created by dynamo processes.

Vainshtein, Samuel I.↗

Ages of globular clusters and helium diffusion

Evolutionary tracks have been calculated with alpha-enhanced compositions which cover the entire globular cluster metallicity range and have constructed isochrones which include the effects of microscopic diffusion of helium. The turnoff magnitudes from the isochrones were combined with the theoretical RR Lyrae magnitudes from Lee to determine the ages of 32 Galactic globular clusters using the magnitude difference between the turnoff and horizontal branch. It is found that including the effects of helium diffusion has a negligible effect on the derived ages of globular clusters. Regardless of the inclusion of helium diffusion, a significant age spread of 5 Gyr among the globular clusters is found. The oldest globular clusters studied here are 17 +/- 2 Gyr old.

Chaboyer, Brian↗

Extensions to the classical calculation of the effect of mutual shadowing in diffuse reflection

The classical method for accounting for the mutual shadowing among closely packed particles in multiple scattering calculations is extended in the following ways. (1) By modeling the particle distribution by a Poisson process with a varying density parameter, a 'Van der Waals' type approximation allows extension to a greater fractional volume density, D. In this case it is only required that D squared be much less than 1 instead of D being much less than 1. (2) In the case that the particle distribution is not uniform the classical calculation may be weighted by the pair correlation function of the distribution. (3) The use of the Markov chain formalism for radiative transfer allows inclusion of the effect of shadowing for two orders of scattering. For conditions such as might apply in Saturn's rings, the inclusion of this effect makes less than a 0.1% difference in the calculated phase curves, compared to previous calculations which have included shadowing only in the first scattering. The latter are thus shown to be quite accurate.

Esposito, L. W.↗

Uncertainty Determination for Aeroheating in Uranus and Saturn Probe Entries by the Monte Carlo Method

The 2013-2022 Decaedal survey for planetary exploration has identified probe missions to Uranus and Saturn as high priorities. This work endeavors to examine the uncertainty for determining aeroheating in such entry environments. Representative entry trajectories are constructed using the TRAJ software. Flowfields at selected points on the trajectories are then computed using the Data Parallel Line Relaxation (DPLR) Computational Fluid Dynamics Code. A Monte Carlo study is performed on the DPLR input parameters to determine the uncertainty in the predicted aeroheating, and correlation coefficients are examined to identify which input parameters show the most influence on the uncertainty. A review of the present best practices for input parameters (e.g. transport coefficient and vibrational relaxation time) is also conducted. It is found that the 2(sigma) - uncertainty for heating on Uranus entry is no more than 2.1%, assuming an equilibrium catalytic wall, with the uncertainty being determined primarily by diffusion and H(sub 2) recombination rate within the boundary layer. However, if the wall is assumed to be partially or non-catalytic, this uncertainty may increase to as large as 18%. The catalytic wall model can contribute over 3x change in heat flux and a 20% variation in film coefficient. Therefore, coupled material response/fluid dynamic models are recommended for this problem. It was also found that much of this variability is artificially suppressed when a constant Schmidt number approach is implemented. Because the boundary layer is reacting, it is necessary to employ self-consistent effective binary diffusion to obtain a correct thermal transport solution. For Saturn entries, the 2(sigma) - uncertainty for convective heating was less than 3.7%. The major uncertainty driver was dependent on shock temperature/velocity, changing from boundary layer thermal conductivity to diffusivity and then to shock layer ionization rate as velocity increases. While radiative heating for Uranus entry was negligible, the nominal solution for Saturn computed up to 20% radiative heating at the highest velocity examined. The radiative heating followed a non-normal distribution, with up to a 3x variation in magnitude. This uncertainty is driven by the H(sub 2) dissociation rate, as H(sub 2) that persists in the hot non-equilibrium zone contributes significantly to radiation.

Palmer, Grant↗

Analysis of Silver Release from Furnace-Tested TRISO Particles

High temperature testing of intact TRISO particles previously irradiated in the AGR-5/6/7 experiment was performed in the Furnace for Irradiated TRISO Testing (FITT) to directly confirm diffusive release of silver and europium from intact TRISO particles. Testing was conducted from 1,100–1,600°C for exposure times up to 100 h to directly confirm silver through layer release below safety testing temperatures. The FITT analysis showed highest levels of silver release at 1,300–1,400°C which confirms athermal release behaviors previous observed in step-wise and transient safety tests. Additionally, release was non-uniform with some particles releasing a majority of their inventory while others did not appear to release silver under identical testing conditions, which was consistent with historic observations. An assessment of the effective silver diffusion coefficient in the SiC layer was conducted and indicated maximum values in the 1,300–1,400°C range. The magnitude of the calculated diffusion coefficients also exceeded currently accepted diffusion coefficients. The release behavior of europium from intact particles was also analyzed in FITT for at 1,450–1,550°C for 500 h to 750 h. Direct confirmation of europium release below safety testing temperatures was confirmed absent contributions from matrix release. The analysis indicated europium release follows a general Arrhenius behavior and suggests general uniform release and indicates irradiation conditions influence observed release response. Calculated diffusion kinetics agree well with historic experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

On the modelling of non-reactive and reactive turbulent combustor flows

A study of non-reactive and reactive axisymmetric combustor flows with and without swirl is presented. Closure of the Reynolds equations is achieved by three models: kappa-epsilon, algebraic stress and Reynolds stress closure. Performance of two locally nonequilibrium and one equilibrium algebraic stress models is analyzed assuming four pressure strain models. A comparison is also made of the performance of a high and a low Reynolds number model for combustor flow calculations using Reynolds stress closures. Effects of diffusion and pressure-strain models on these closures are also investigated. Two models for the scalar transport are presented. One employs the second-moment closure which solves the transport equations for the scalar fluxes, while the other solves the algebraic equations for the scalar fluxes. In addition, two cases of non-premixed and one case of premixed combustion are considered. Fast- and finite-rate chemistry models are applied to non-premixed combustion. Both show promise for application in gas turbine combustors. However, finite rate chemistry models need to be examined to establish a suitable coupling of the heat release effects on turbulence field and rate constants.

Nikjooy, Mohammad↗

Grain Boundary Effects on Radiation Damage and Tritium Diffusion in Li–Al–O Ceramics from Molecular Dynamics and Experiments

Understanding irradiation damage and tritium transport in LiAlO2 ceramics is essential for their deployment in tritium-producing burnable absorber rods (TPBARs). Grain boundaries (GBs) play an important role in governing radiation response and tritium transport in LiAlO2 and its secondary phase LiAl5O8. Using molecular dynamics simulations, we investigated defect evolution and tritium diffusion during displacement cascades in single-crystal and bicrystal LiAlO2 and LiAl5O8 at 600 K. The results reveal that GBs suppress the damage in the LiAlO2 bicrystals as compared to single crystals, via interstitial emission. The effect is more pronounced for Li defects, than for Al and O. In LiAl5O8 the damage reduction due to introduction of GB is less pronounced overall. Tritium diffusion coefficients at GBs are higher by factors of 2–10 relative to diffusion inside grain bulk. The effect is particularly pronounced in LiAlO2, where S5, S17, and S25 GBs promote rapid tritium transport, whereas LiAl5O8 exhibits slower diffusion due to reduced free volume at its GBs. These findings evince a trade-off that while GBs mitigate radiation damage by absorbing interstitials, they simultaneously provide fast pathways for tritium migration which is not desirable for TPBAR application. The mechanistic insights gained here establish a foundation for microstructural design strategies to balance radiation tolerance and tritium retention in ceramic breeder materials.

Roy, Ankit↗

NASA/DOD Aerospace Knowledge Diffusion Research Project. Use of Communications Sources: An Intercultural Investigation of Practices in the US and Russia

The purpose of this paper is to investigate the impact of U.S./Russian cultural differences in communications among scientists and engineers in applied technology industries. This is important because the advent of perestroika, the breakup of the Soviet Union, and massive moves toward privatization make Russia a potential partner in economic endeavors and, at the same time, a possible competitor in the international arena. Unfortunately the results of U.S./Soviet collaborative endeavors have not always met with expectations. Since 1987, when the former USSR adopted a law on joint ventures, evidence has emerged as to the causes of many failures of these cooperative arrangements. While international strategic alliances face many structural barriers, failures of these cooperative ventures have often resulted from a lack of understanding of the more intangible barrier of major differences in cultural environments between the partners (Cattaneo, 1992). Cultural differences not only affect business operations but also raise questions for scholars and practitioners who have advocated that U.S. management theories apply abroad. Boyacigiller and Adler (1991), Doktor, Tung, and Von Glinow (1991), and Hofstede (1993) observed that most U.S. scholars have continued to export management concepts and practices abroad assuming the concepts were universally valid despite the fact that Western organizational theory has placed little emphasis on factors such as history, social setting, culture, and government (Boyacigiller & Adler, 1991). High technology industries such as aerospace, which includes the cormmercial aviation segment, have characteristics that make the industry an excellent platform to study cultural implications for technical communications. The investigation of this group is worthwhile for several reasons. First, high technology industries are becoming more international and more engaged in collaborative endeavors. Second, the industries are highly dependent on effective innovation diffusion which, according to Fischer (1979), is essentially information exchange. And, third, studies of innovative project management have found that information availability was a critical factor in project success or failure (e.g., Link & Zmud, 1987; Tushman, 1978, 1979). We propose that a gap in the literature exists that centers on whether U.S. paradigms of commnunications behavior apply to other cultures. First, we will explore early findings in the U.S. that held that the choice of an information source was a function of the 'law of least effort' rather than quality (e.g., Allen, 1977; Cuinan, 1983; DeWhirst, 1971; Hardy, 1982; O'Reilly, 1982; Rosenberg, 1967). Second, we will explore the contingency approaches such as that of Tushman (1979) and the later work of Daft and Lengel (1984, 1987), Huber and Daft (1987) and Lengel and Daft (1988) who held that information choice was a function of the nature of the task at hand. A third issue to be addressed is the confounding problem of presumed differences between scientists and engineers in information gathering behavior (Allen, 1977). Finally, we will investigate whether cultural differences cast doubt on the applicability of findings from U.S. situations to other cultures.

Pinelli, Thomas E.↗

Adaptive grid relocation algorithms for transonic full potential calculations using one-dimensional or two-dimensional diffusion equation

The effect of solution-adaptive grids using an interpolative grid relocation algorithm on two-dimensional transonic full potential flow calculations is studied with extensions to three dimensions in mind. One-dimensional or two-dimensional diffusion equation is solved to obtain the grid density control function for generating adaptive grids. The results of flow solution for NACA-0012 and Gates-Leajet airfoils show a significant improvement of accuracy in the CP distributions. However, further studies are recommended on the questions (1) what information from the initial flow solution should be passed on to the solution-adaptive grid generation scheme, and (2) how to optimize the accuracy of the solution through the use of adaptive grids.

Nakamura, S.↗

Validation of a comprehensive first-principles-based framework for predicting the performance of future stellarators

This paper presents the validation of the GENE-KNOSOS-Tango framework for recovering both the steady-state plasma profiles in the considered radial domain and selected turbulence trends in a stellarator. This framework couples the gyrokinetic turbulence code GENE, the neoclassical transport code KNOSOS, and the transport solver Tango in a multi-timescale simulation feedback loop. Ion-scale kinetic-electron and electron-scale adiabatic-ion flux-tube simulations were performed to evolve the density and temperature profiles for four OP1.2b W7-X scenarios. The simulated density and temperature profiles showed good agreement with the experimental data using a reasonable set of boundary conditions. Equally important was the reproduction of observed trends for several turbulence properties, such as density fluctuations and turbulent heat diffusivities. Key effects were also touched upon, such as electron-scale turbulence and the neoclassical radial electric field shear. The validation of the GENE-KNOSOS-Tango framework enables credible predictions of physical phenomena in stellarators and reactor performance based on a given set of edge parameters.

Gyrokinetic simulations↗

Topology optimization for the full-cell design of porous electrodes in electrochemical energy storage devices

In this paper, we introduce a density-based topology optimization framework to design porous electrodes for maximum energy storage. We simulate the full cell with a model that incorporates electronic potential, ionic potential, and electrolyte concentration. The system consists of three materials, namely pure liquid electrolyte and the porous solids of the anode and cathode, for which we determine the optimal placement. We use separate electronic potentials to model each electrode, which allows interdigitated designs. As a result, a penalization is required to ensure that the anode and cathode do not touch, i.e., causing a short circuit. We compare multiple 2D designs generated for different fixed conditions, e.g. material properties. A 3D design with complex channel and interlocked structure is also created. All optimized designs are far superior to the traditional monolithic electrode design with respect to energy storage metrics. We observe up to a 750% increase in energy storage for cases with slow effective ionic diffusion within the porous electrode.

25 ENERGY STORAGE↗

A snapshot of high-entropy alloy processing techniques and their effects on resulting mechanical properties

High-entropy alloys (HEAs) exhibit exceptional strength, corrosion resistance, and thermal stability, making them promising candidates for nuclear, aerospace, and other extreme applications. While most prior work has focused on compositional design, manufacturing techniques themselves can alter microstructure and mechanical properties as dramatically as alloy chemistry. This review compiles and compares the effects of processing routes—including arc melting, induction melting, mechanical alloying with spark plasma sintering, and additive manufacturing—on the structure and properties of HEAs. Quantitative comparisons highlight, for example, that SPS-processed alloys can achieve ∼20–45 % higher yield and tensile strength than arc-melted counterparts, while Bridgman solidification produces nearly single-crystal structures with elongation to failure exceeding 80 %. Additive manufacturing routes such as selective laser melting offer fine microstructures but also introduce anisotropy and porosity, leading to yield strengths spanning 100–600 MPa for the same composition. By synthesizing such results, this review provides actionable insight into how processing routes interact with HEA core effects (high entropy, lattice distortion, sluggish diffusion, and cocktail effect) to determine performance, thereby offering a practical guide for optimizing manufacturing strategies.

36 MATERIALS SCIENCE↗

Impact of temperature variations on BISON predictions of Ag release in AGR-1 and AGR-2 experiments

Understanding and quantifying the release of fission products like silver (Ag) from TRistructural ISOtropic (TRISO) fuel particles is important to assess the safe operation of advanced high temperature reactors. Although the silicon carbide (SiC) layer of TRISO particles is effective as the main fission product barrier, Ag can be released from intact TRISO particles. A mechanistic model for the effective Ag diffusivity, D eff , was previously developed as a function of temperature and microstructure variables informed by atomistic modeling of Ag diffusivity on the mesoscale. Here in this study, we use this model to explore how experimental temperature uncertainties impact the overall predicted Ag release. This analysis shows that temperature uncertainties have a significant impact on the overall Ag release predictions. Furthermore, we show that the time average volume average temperature (TAVA) temperature is not an appropriate proxy for temperature histories to predict fission product release. We attribute this to the Arrhenius dependence of Ag diffusivity with respect to temperature. The detailed temperature histories, therefore, provide the most accurate results are are of most importance for modeling efforts. Overall, this work shows the importance of considering the experimental uncertainty of the temperature on computational predictions of fission product transport and release and the need for more accurate temperature histories from future experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗