Search NASA⌕ Search

SEARCH · Search NASA

Results for “Damage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Effects of moisture, residual thermal curing stresses and mechanical load on the damage development in quasi-isotropic laminates

Classical laminate theory and a finite element model were used to predict stress states prior to the first formation of damage in laminates fabricated from T/300/5208. Crack patterns characteristic of the laminate in a wet or dry condition were also predicted using a shear lag model. Development of edge damage was recorded and observed during the test by transferring an image of the damage from the edge surface on to a thin acetate sheet such that the damage imprinted could be immediately viewed on a microfiche card reader. Moisture was shown to significantly alter the interior and edge dry stress states due to swelling and a reduction of elastic properties and to reduce the transverse strength in 90 deg plies. A model was developed in order to predict changes in first ply failure laminate loads due to differences in stacking sequence together with a wet or dry environmental condition.

Kriz, R. D.↗
NASA NTRS1980

The potential for damage from the accidental release of conductive carbon fibers from aircraft composites

The paper considers the potential for damage from the accidental release of conductive carbon fibers from aircraft composites. The electrical conductivity of carbon and graphite fibers has led to electrical equipment damage from the inadvertent release of virgin fibers into the atmosphere; an accidental release of carbon fibers from filamentary composites from the burning of crashed commercial airliners could damage electrical and electronic equipment. The experimental and analytical results by NASA of the methods of assessing the extent of potential damage in terms of costs is presented; the NASA materials research program to provide alternate or modified composites to overcome electrical hazards of carbon composites in aircraft structures is described.

Bell, V. L.↗
NASA NTRS1979

Dynamic response of damaged angleplied fiber composites

An investigation was conducted to determine the effects of low level damage induced by monotonic load, cyclic load and/or residual stresses on the vibration frequencies and damping factors of fiber composite angleplied laminates. Two different composite systems were studied - low modulus fiber and ultra high modulus fiber composites. The results obtained showed that the frequencies and damping factors of angleplied laminates made from low modulus fiber composites are sensitive to low level damage while those made from ultra high modulus composites are not. Also, vibration tests may not be sufficiently sensitive to assess concentrated local damage in angleplied laminates. And furthermore, dynamic response determined from low-velocity impact coupled with the Fast Fourier Transform and packaged in a minicomputer can be a convenient procedure for assessing low-level damage in fiber composite angleplied laminates.

Chamis, C. C.↗
NASA NTRS1981

Development of an engineering analysis of progressive damage in composites during low velocity impact

A computerized, analytical methodology was developed to study damage accumulation during low velocity lateral impact of layered composite plates. The impact event was modeled as perfectly plastic with complete momentum transfer to the plate structure. A transient dynamic finite element approach was selected to predict the displacement time response of the plate structure. Composite ply and interlaminar stresses were computed at selected time intervals and subsequently evaluated to predict layer and interlaminar damage. The effects of damage on elemental stiffness were then incorporated back into the analysis for subsequent time steps. Damage predicted included fiber failure, matrix ply failure and interlaminar delamination.

Humphreys, E. A.↗
NASA NTRS1982

Effect of lubricant environment on saw damage in silicon wafers

The chemomechanical effect of lubricant environments on the inner diameter (ID) sawing induced surface damage in Si wafers was tested for four different lubricants: water, dielectric oil, and two commercial cutting solutions. The effects of applying different potential on Si crystals during the sawing were also tested. It is indicated that the number and depth of surface damage are sensitive to the chemical nature of the saw lubricant. It is determined that the lubricants that are good catalysts for breaking Si bonds can dampen the out of plane blade vibration more effectively and produce less surface damage. Correlations between the applied potential and the depth of damage in the dielectric oil and one of the commercial cutting solutions and possible mechanisms involved are discussed.

Kuan, T. S.↗
NASA NTRS1982

Pre- and post-annealing of mechanical damage in silicon wafers

Basic properties of mechanical damage in silicon consisting of cracks and abrasion were studied using transmission electron microscopy. The crystallographic structure of mechanical damage was determined before and after high temperature annealing. The main findings include that stresses in silicon around crack tips are not plastically relieved at room temperature and that abrasion at room temperature introduces shear loops into the silicon. It was also found that cracks of micron size can be annealed out, specifically, if cleavage occurs on 111 planes. The healing products of such cracks are 60 deg and 90 deg dislocations. Submicron cracks transform into stacking faults during annealing. Likewise high concentrations of shear loops due abrasion were found to anneal into stacking faults. A one to one correlation between surface areas containing small cracks and stacking faults was made. Measurements of damage removal on silicon surfaces through chemical-mechanical etching techniques are presented. It is shown that silicon dioxide repolishes damaged silicon surfaces most effectively.

Schwottke, G. H.↗
NASA NTRS1980

Behavior of damaged graphite/epoxy laminates under compression loading

The influence of three different resin systems on the damage tolerance of graphite/polymer laminates was evaluated. Testing consisted of both static compression and cyclic compression evaluation of 10.2 by 15.2 by 0.5 cm (4 by 6 by 0.2 in) laminates with circular holes, simulated delaminations, and low velocity impact. Damage growth under steadily increasing compression and cyclic compression loading was monitored. Damage size and impact-induced failures for the three materials were compared. Of the three material systems evaluated, the one most tolerant to impact damage exhibited the least delamination within the cross section due to impact, the highest transverse tension strain to failure, and the largest crack opening force, as determined from double cantilever beam tests.

Byers, B. A.↗
NASA NTRS1981

The effect of lamination-induced stresses on fatigue damage development at internal flaws

The effects of stresses induced by the lamination of off-axis plies to O-deg lamina on the development of damage during the fatigue loading of the O-deg plies are discussed. The transverse normal stresses in the plane of the laminae and the laminate created by the laminating constraints when an axial force is applied to the laminate are calculated in terms of a differential Poisson ratio between the ply in question in the unconstrained and constrained states, and significant differences in the constraint environments of an unnotched specimen joined to plies of 45 and 90 deg inclination are noted which correspond to an increase in longitudinal splitting in the 90 deg case and a marked decrease in longitudinal splitting in the 45 deg case. If a notch is present, shear and crack-opening damage is found to be very effectively suppressed in 45-deg laminates, and less so in the 90-deg case. It is pointed out that whereas the 45-deg laminate represents the least damage situation, it does not have the greatest notched strength. It is concluded that an understanding and prediction of damage development in laminates requires knowledge of the stress fields caused by the lamination constraints.

Reifsnider, K. L.↗
NASA NTRS1981

Enhanced annealing of GaAs solar cell radiation damage

Solar cells are degraded by radiation damage in space. Investigations have been conducted concerning possibilities for annealing this radiation damage in GaAs solar cells, taking into account the conditions favoring such annealing. It has been found that continuous annealing as well as the combination of injection annealing with thermal annealing can lead to recovery from radiation damage under particularly favorable conditions in GaAs solar cells. The damage caused by both electrons and protons in GaAs solar cells can be substantially reduced by annealing at temperatures as low as 150 C, under appropriate conditions. This possibility makes the GaAs solar cells especially attractive for long space missions, or for missions in severe radiation environments. Attention is given to results concerning periodic thermal annealing, continuous annealing, and injection annealing combined with thermal annealing.

Loo, R.↗
NASA NTRS1981

Damage and coefficients and thermal annealing of irradiated silicon and GaAs solar cells

Electron and proton damage coefficients have been measured for several types of silicon cells of recent manufacture using 1 MeV electrons and protons with energies of 8.3, 17.5 and 40 MeV. LPE (AlGa)As-GaAs cells were also irradiated and pseudodamage coefficients derived under the assumption that the irradiation changes the diffusion length in only one of the n- or p-type layers. After irradiation the cells were annealed isochronally up to 450 C. The damage coefficient and annealing data for silicon cells are in substantial agreement with previous work. The GaAs cells have pseudo-damage coefficients which are dependent on fluence, and have about the same energy dependence as Si damage coefficients.

Anspaugh, B. E.↗
NASA NTRS1982

Fracture and crack growth in orthotropic laminates. Part 2: Experimental determination of internal damage growth in unidirectional boron/aluminum composite laminates

The fracture behavior of unidirectional boron/aluminum composite laminates is investigated in order to verify the results of mathematical models. These models predict the stresses and displacements of fibers and the amount of damage growth in a center-notched lamina as a function of the applied remote stress and the matrix and fiber material properties. The damage may take the form of longitudinal yielding and splitting in the matrix as well as stable transverse damage consisting of broken fibers and matrix yielding ahead of the notch. A brittle lacquer coating is used to detect the yielding in the matrix while X-ray techniques are used to detemine the number of broken fibers in the laminate. The notched strengths and the amounts of damage found in the experimental specimens agree well with those predicted by the mathematical model.

Goree, J. G.↗
NASA NTRS1982

Wind-tunnel studies of the effects of stimulated damage on the aerodynamic characteristics of airplanes and missiles

As an aid in assessing the aerodynamic effects of battle damage that might be sustained by military airplanes or missiles, several wind tunnel investigations were performed at the Langley Research Center in which damage was simulated with models by the removal of all or parts of the wing and tails. Results of the investigations indicate that the loss of a major part of the vertical tail will probably result in the loss of an airplane in any speed range. The loss of major parts of the horizontal tail generally results in catastrophic instability in the subsonic range but, at low supersonic speeds, and for some planform configurations at subsonic speeds, may allow stable flight to the extent that the airplane might return to friendly territory before the pilot must eject. The results further indicate that major damage to the wing, up to the point of the complete removal of one wing panel, and major damage to the horizontal tail may be sustained without necessarily causing the loss of the airplane or pilot.

Spearman, M. L.↗
NASA NTRS1982

Radiation damage

The radiation damage workshop considered a variety of topics among which were the need for equivalent electron fluences in gallium arsenide, the possibility of 15 percent end-of-life efficiencies for silicon, increasing radiation resistance in gallium arsenide, annealing of radiation damage and the need for radiation damage studies in cascade cells. The workshop members agreed that a high priority should be assigned to obtaining equivalent electron fluences for gallium arsenide cells. It was suggested that 1 MeV would be a reasonable electron energy for this purpose. Special care should be given to proton irradiations particularly for energies below 1 MeV. In addition, omnidirectional rather than normal incidence protons should be used. It was also agreed that there was a need for obtaining damage coefficients in gallium arsenide. In silicon, there is a requirement for additional flight data, especially in proton dominated orbits. These data are needed to further check the accuracy of the 1 MeV equivalence fluences.

Weinberg, I.↗
NASA NTRS1982

Effects of moisture, residual thermal curing stresses, and mechanical load on the damage development in quasi-isotropic laminates

This investigation demonstrates how moisture absorbed in (0/+ or - 45/90)s and (0/90/+ or - 45)s graphite epoxy laminates significantly alters the stress state and chronology of damage development along the laminate edge during static tension and tension-tension cyclic loading. Emphasis is placed on using reasonable approximations for wet and dry elastic properties, including out-of-plane properties (nu sub 23 and G sub 23), since these properties are required by finite element and shear lag models to predict the stress state at the laminate edge. Moisture was observed to alter the dry edge stress state in the 90-deg plies of the (0/+ or - 45/90)s laminate such that delaminations occurred at a lower load and transverse cracks occurred at a higher load. A model was developed which predicted the differences in loads required to initiate damage in the 90-deg plies of the two laminates in the wet and dry conditions. Although moisture can alter the chronology of damage development, the damage state in each laminate observed prior to fracture appeared to be independent of moisture content.

Kriz, R. D.↗
NASA NTRS1983

Residual strength assessment of low velocity impact damage of graphite-epoxy laminates

This report contains the study of Low Velocity Transverse Impact Damage of graphite-epoxy T300/5208 composite laminates. The specimen, 100 mm diameter clamped plates, were impact damaged by a cantilever-type instrumented 1-inch diameter steel ball. Study was limited to impact velocity 6 m/sec. Rectangular strips, 50 mm x 125 mm, were cut from the impact-damage specimens so that the impact damage zone was in the center of the strips. These strips were tested in tension to obtain their residual strength. An energy dissipation model was developed to predict the residual strength from fracture mechanics concepts. Net energy absorbed I(a) was evaluated from coefficient of restitution concepts based on shear dominated theory of fiber-reinforced materials, with the modification that during loading and unloading the shear deformation are respectively elastic-plastic and elastic. Delamination energy I(d) was predicted by assuming that the stiffness of the laminate dropped due to debonding. Fiber-breakage energy, assumed to be equal to the difference of I(a) and I(d), was used to determine the residual strength. Predictions were compared with test results.

Lal, K. M.↗
NASA NTRS1983

The damage equivalence of electrons, protons, alphas and gamma rays in rad-hard MOS devices

This paper reports on a study of damage equivalence in rad-hard MOS devices with 100,000 rads (SiO2) capability. Damage sensitivities for electrons of 1, 2, 3, 5, and 7 MeV, protons of 1, 3, 7, 22, and 40 MeV, 3.4-MeV alphas, and Co-60 gammas were measured and compared. Results indicated that qualitatively the same charge recombination effects occurred in hard oxide devices for doses of 100,000 rads (SiO2) as in soft oxide parts for doses of 1 to 4 krads (SiO2). Consequently, damage equivalency or non-equivalency depended on radiation type and energy. However, recovery effects, both during and after irradiation, controlled relative damage sensitivity and its dependency on total dose, dose rate, supply bias, gate bias, radiation type, and energy. Correction factors can be derived from these data or from similar tests of other hard oxide type, so as to properly evaluate the combined effects of the total space environment.

Stassinopoulos, E. G.↗
NASA NTRS1982

Effect of resin on impact damage tolerance of graphite/epoxy laminates

Twenty-four different epoxy resin systems were evaluated by a variety of test techniques to identify materials that exhibited improved impact damage tolerance in graphite/epoxy composite laminates. Forty-eight-ply composite panels of five of the material systems were able to sustain 100 m/s impact by a 1.27-cm-diameter aluminum projectile while statically loaded to strains of 0.005. Of the five materials with the highest tolerance to impact, two had elastomeric additives, two had thermoplastic additives, and one had a vinyl modifier; all the five systems used bisphenol A as the base resin. An evaluation of test results shows that the laminate damage tolerance is largely determined by the resin tensile properties, and that improvements in laminate damage tolerance are not necessarily made at the expense of room-temperature mechanical properties. The results also suggest that a resin volume fraction of 40 percent or greater may be required to permit the plastic flow between fibers necessary for improved damage tolerance.

Williams, J. G.↗
NASA NTRS1984

Compression failure characteristics of + or - 45-deg-dominated laminates with a circular hole or impact damage

An investigation of the compression failure characteristics of + or - 45-deg-dominated laminates with a circular hole or impact damage was conducted. Graphite-epoxy laminates consisting of all + or - 45-deg plies and of + or - 45-deg and 90-deg plies were evaluated. Inplane shearing between the fibers and matrix (i.e., matrix shearing) was found to be the primary compression failure mechanism for an all + or - 45-deg laminate with a hole. The failure mechanism for the + or 45-deg-dominated laminates with a hole appeared to be a combination of delamination and matrix shearing. The compression failure stresses and strains for both the all + or - 45-deg laminate and the + or - 45-deg-dominated laminates were unaffected by impact damage at an energy level of 5.5 J when compared to results for undamaged control specimens. The failure stresses and strains for all laminates with impact damage at an energy level of 17.0 J or of 34.3 J were significantly lower than the corresponding data for the undamaged control specimens. The failure stresses and strains for these impact-damaged specimens were independent of the percentage of 90-deg plies in the laminate.

Shuart, M. J.↗