Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dimensionless Numbers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Noise characteristics of the gas ionization cascade used in low vacuum scanning electron microscopy

The noise characteristics of gas cascade amplified electron signals in low vacuum scanning electron microscopy (LVSEM) are described and analyzed. We derive expressions for each component contributing to the total noise culminating in a predictive, quantitative model that can be used for optimization of LVSEM operating parameters. Signal and noise behavior is characterized experimentally and used to validate the model. Under most operating conditions, the noise is dominated by the excess noise generated in the gas amplification cascade. At high gains, the excess noise increases proportionally with gain such that the signal-to-noise ratio is constant. The effects of several instrument operating parameters, including working distance, gas pressure, beam current, and detector bias, are condensed and presented in the form of a master curve.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Two-photon photodissociation dynamics of H{sub 2}O via the D-tilde electronic state

Photodissociation dynamics of H{sub 2}O via the D-tilde state by two-photon absorption have been investigated using the H-atom Rydberg tagging time-of-flight technique. The action spectrum of the D-tilde<-X-tilde transition band has been measured. The predissociation lifetime of the D-tilde state is determined to be about 13.5 fs. The quantum state-resolved OH product translational energy distributions and angular distributions have also been measured. By carefully simulating these distributions, quantum state distributions of the OH product as well as the state-resolved angular anisotropy parameters were determined. The most important pathway of the H{sub 2}O dissociation via the D-tilde state leads to the highly rotationally excited OH(X,v=0) products. Vibrationally excited OH(X) products (up to v=10) and electronically excited OH(A,v=0,1,2) have also been observed. The OH(A)/OH(X) branching ratios are determined to be 17.9% at 244.540 nm (2{omega}{sub 1}=81 761.4 cm{sup -1}) and 19.9% at 244.392 nm (2{omega}{sub 2}=81 811 cm{sup -1}), which are considerably smaller than the value predicted by the theory. These discrepancies are attributed to the nonadiabatic coupling effect between the B-tilde and D-tilde surfaces at the bent geometry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantitative model for the heterogeneity of atomic position fluctuations in proteins: A simulation study

We propose a simple analytical model for the elastic incoherent structure factor of proteins measured by neutron scattering, which allows extracting the distribution of atomic position fluctuations from a fit of the model to the experimental data. The method is validated by applying it to elastic incoherent structure factors of lysozyme which have been obtained by molecular dynamics simulation and by normal mode analysis, respectively, and for which distributions of the atomic position fluctuations can be generated numerically for direct comparison with the predictions of the model. The comparison shows a remarkable agreement, in particular, concerning the lower limit for the position fluctuations, which is pronounced in the numerical data.

60 APPLIED LIFE SCIENCES↗

Dynamics starting at a conical intersection: Application to the photochemistry of pyrrole

The photochemical ring opening process in pyrrole has been investigated by performing classical on-the-fly dynamics using the multiconfiguration self-consistent field method for the computation of energies and energy gradients. As starting point for the dynamics the conical intersection corresponding to the ring-puckered ring-opened structure, determined previously [Barbatti et al., J. Chem. Phys. 125, 164323 (2006)], has been chosen. Two sets of initial conditions for the nuclear velocities were constructed: (i) nuclear velocities in the branching (g,h) plane of the conical intersection and (ii) statistical distribution for all atoms. Both sets of initial conditions show very similar results. Reactive trajectories are only found in a very limited sector in the (g,h) plane and reaction products are very similar. Within the simulation time of 1 ps, ring opening of pyrrole to the biradical NH=CH-CH-CH=CH chain followed by ring closure to a substituted cyclopropene structure (NH=CH-C{sub 3}H{sub 3}) is observed. The computed structural data correlate well with the experimentally observed dissociation products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ionic debris measurement of three extreme ultraviolet sources

Generation of debris in extreme ultraviolet (EUV) light sources is an inherent and real threat to the lifetime of collection optics. Debris measurement of these sources is useful to enable source suppliers to estimate collector lifetime. At the Center for Plasma Material Interactions (CPMI) at the University of Illinois, an Illinois calibrated spherical sector electrostatic energy analyzer (ICE) was built to measure the ion debris flux in absolute units. In addition to ion flux, the detector is also capable of identifying different ion species present in the plasma utilizing energy-to-charge ratio discrimination. The lifetime of the collector optics is calculated using the measured ion flux. In the current investigation we compare the measurement of ion debris production in three different EUV sources: the Energetiq EQ-10M, the AIXUV-100, and the XTREME XTS 13-35. In the EQ-10M source, three angular measurements are coupled with three variations in operating pressure to measure consequent effects on debris production. These measurements reveal four predominant ion species in the energetic debris analysis: C{sup +}, Si{sup +}, Xe{sup +}, and Xe{sup 2+}. The amount of debris is reduced as pressure is increased. Various debris mitigation methods are implemented in the AIXUV-100 source and results reveal that four ion species are observed (Ar{sup +}, Xe{sup +}, Xe{sup 2+}, and W{sup +}), though there does not seem to be a dominant species. The first mitigation technique, backstreaming argon toward the source, reduces the amount of Ar{sup +}, Xe{sup 2+}, and W{sup +}, yet increases the amount of Xe{sup +} The increase in Xe{sup +} flux is explained based on charge exchange phenomena. The ICE machine was then attached 1.92 m away from the pinch of XTS 13-35 source, and placed at 25 deg. away from the normal line. The comparison of results reveals that the XTS 13-35 and the EQ-10M sources produced comparable amounts of energetic ion flux per watt of EUV light produced. The AIXUV-100 source generated more ion debris flux per watt of EUV light than the other two sources, though it should be noted that the AIXUV-100 source was capable of producing more than ten times the amount of EUV light power compared to any of the other sources.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

XRD, Photoluminescence and Optical Absorption Investigations of Cobalt-doped ZnO

Zn{sub 1-x}Co{sub x}O(with x = 0, 0.01, 0.10 and 0.20) were synthesized by solid-state reaction method sintered at 600 deg. C for 12 hours. The samples were studied by X-ray diffraction (XRD), optical absorption (UV-Vis) and Photoluminescence (PL). Structural analysis by Rietveld method using XRD showed that the peaks of secondary phase Co{sub 3}O{sub 4} with a cubic structure were visible in the high-doped sample (x = 0.1, 0.2), besides the main peaks of wurtzite-like structure the same as that of ZnO. Shift of the XRD peaks proved the incorporation of Co{sup 2+} into the ZnO lattice. The band gap energy decreased from 3.18 to 3.14 eV with the increasing of cobalt concentration. PL spectra at room temperature showed the blue emission with the peak around 412 nm. In addition, the intensity of the blue emission decreased upon increasing the Co concentration, which indicated their high structural, defects and optical quality in the ZnO.

36 MATERIALS SCIENCE↗

Nonadiabatic reactive scattering in atom+triatom systems: Nascent rovibronic distributions in F+H{sub 2}O{yields}HF+OH

Crossed supersonic jet studies of F+H{sub 2}O{yields}HF+OH({sup 2}{Pi}{sub 3/2},{sup 2}{Pi}{sub 1/2}) have been performed under low density, single collision conditions at E{sub com}=6(2) kcal/mol, yielding rotational, vibrational, and spin-orbit state distributions in the nascent OH product by laser induced fluorescence methods. The lowest reaction barriers on the ground and first excited electronic surfaces are {Delta}E{approx_equal}4 kcal/mol and {Delta}E{approx_equal}25 kcal/mol, correlating with OH({sup 2}{Pi}{sub 3/2}) and OH({sup 2}{Pi}{sub 1/2}), respectively. Although only reactions on the ground state potential are Born-Oppenheimer allowed at the experimental collision energies, both ground and excited spin-orbit OH products are observed in a {sup 2}{Pi}{sub 3/2}:{sup 2}{Pi}{sub 1/2}=69(1)%:31(1)% branching ratio. This indicates the presence of strong nonadiabatic surface hopping interactions, in agreement with previous results for the F+D{sub 2}O{yields}DF+OD reaction. Despite clear differences in the rotational distributions between F+H{sub 2}O and F+D{sub 2}O isotopic reactions, the overall electronic branching into spin-orbit manifolds is nearly identical for both OH and OD products. Furthermore, when plotted versus total electronic+rotational energy, the nascent OH and OD populations each lie on single curves, with pronounced kinks in the Boltzmann plots suggestive of microscopic branching in the reaction dynamics. Such an equivalence of electronic and rotational energy release in the OH/OD products is consistent with predominantly nonadiabatic processes taking place in the immediate post-transition state region rather than asymptotically in the exit channel.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electrical Properties and Phase Transition Behaviors of Sn Doped 0.45PZT-0.55PNN Ceramics

Dielectric properties, and phase transition behaviors of Sn doped 0.45PbZr{sub 1/2}Ti{sub 1/2}O{sub 3}--0.55PbNi{sub 1/3}Nb{sub 2/3}O{sub 3} ceramics has been investigated. The ceramics were prepared by a normal solid-state method and were characterized, using a variety of techniques. For undoped samples, high relative permittivity of >21000 (at 1 k Hz) was found at the transition temperature of 104 deg. C. With increasing Sn concentration, the degree of diffuse phase transition was enhanced and a linear reduction in the transition temperature was produced.

36 MATERIALS SCIENCE↗

Phase evolutions and electrical properties in BaTiO{sub 3}-BaFe{sub 0.5}Nb{sub 0.5}O{sub 3} ceramics

In this work, BaFe{sub 0.5}Nb{sub 0.5}O{sub 3}(BFN) was added to BaTiO{sub 3}(BT) to form the solid solution. The investigation of phase evolution, physical properties and electrical properties of the binary system (1-x)BT-xBFN where x = 0, 0.2, 0.4 and 0.6 was carried out. The BT and BFN powders were prepared separately using a calcination technique with optimum calcinations temperature for producing both BT and BFN powders. XRD results revealed that the BT-BFN ceramics with BFN content of x less than 0.4 contain the ferroelectric tetragonal perovskite phase whereas the composition with BFN content of x 0.6 changes symmety to the cubic phase. From the evidences including phases, microstructures and ferroelectric and dielectric data of the BT-BFN ceramics, it is inferred that the morphotropic phase boundary occurs around the composition ox = 0.4.

36 MATERIALS SCIENCE↗

REVIEW OF THE NATIONAL SPHERICAL TORUS EXPERIMENT RESEARCH RESULTS

The National Spherical Torus Experiment (NSTX) produces plasmas, with toroidal aspect ratio as low as 1.25 and plasma currents up to 1.5 MA, which can be heated by up to 6 MW High-Harmonic Fast Waves and up to 7 MW of deuterium Neutral Beam Injection. With these capabilities, NSTX has already made considerable progress in advancing the scientific understanding of high performance plasmas needed for low-aspect-ratio reactor concepts and for ITER. In transport and turbulence research on NSTX, the role of magnetic shear is being elucidated in discharges in which electron energy transport barriers are observed. Scaling studies indicate a weaker dependence on plasma current than at conventional aspect ratio and a significant dependence on toroidal field (B{sub T}).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Convection in molten pool created by a concentrated energy flux on a solid metal target

During surface evaporation of metals by use of a concentrated energy flux such as electron beam or lasers, a liquid metal pool having a very high temperature gradient is formed around the hot zone created by the beam. Due to temperature dependence of surface tension, density, and depression of the evaporating surface caused by back pressure of the emitted vapor in this molten pool, a strong convective current sets in the molten pool. A proposition is made that this convection may pass through three different stages during increase in the electron beam power depending upon dominance of the various driving forces. To confirm this, convective heat transfer is quantified in terms of dimensionless Nusselt number and its evolution with power is studied in an experiment using aluminum, copper, and zirconium as targets. These experimentally determined values are also compared to the theoretical values predicted by earlier researchers to test the validity of their assumptions and to know about the type of flow in the melt pool. Thus, conclusion about the physical characteristics of flow in the molten pool of metals could be drawn by considering the roles of surface tension and curvature of the evaporating surface on the evolution of convective heat transfer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The Tensor Analysing Power Component T{sub 21} of Exclusive pi{sup -}-meson Photoproduction on Deuteron in the Resonance Region

The experimental data about the tensor analyzing power component T{sub 21} of the pi-meson photo-production on the polarized deuterons are presented here along with the theoretical calculation. The experiment has been performed at the 2 GeV Novosibirsk VEPP-3 electron storage ring using an internal polarized deuterium target by detecting the two protons in coincidence.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Towards High Precision Deuteron Polarimetry

A finite electric dipole moment (EDM) in any fundamental system would constitute a signal for new physics. The deuteron presents itself as an optimal candidate both experimentally and theoretically. A new storage ring technique is being developed for which a small change in the vertical polarization would be a signal of a non-zero EDM. A novel polarimeter concept is under investigation. Besides being highly efficient, this polarimeter should continuously monitor the beam polarization, guaranteeing optimal sensitivity. Detailed studies on systematic error control, in addition to the measurement of cross sections and analyzing powers, were carried out at KVI-Groningen in The Netherlands. Measurements were conducted at COSY-Juelich in Germany yielding high efficiencies. The (statistics limited) ability to track changes in polarization at the level of a few hundred parts-per-million has been demonstrated. Further studies and developments to meet the final goal of sub-part-per-million sensitivity are in progress.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Towards Improved Proton Polarimetry at RHIC

The RHIC polarized proton collider polarimeters employ the analyzing power in p-Carbon elastic scattering in the Coulomb Nuclear Interference region to measure the proton beam polarization. These are calibrated by the polarized hydrogen jet target that measures the absolute beam polarization utilizing the pp elastic scattering process in the CNI region. This paper describes the status of these polarimeters and the efforts employed to improve the performance in terms of better resolution, rate handling capability, and reduced systematic uncertainties.

43 PARTICLE ACCELERATORS↗

Dynamically Polarized Sample for Neutron Scattering At the Spallation Neutron Source

The recently constructed Spallation Neutron Source at the Oak Ridge National Laboratory is quickly becoming the world's leader in neutron scattering sciences. In addition to the world's most intense pulsed neutron source, we are continuously constructing state of the art neutron scattering instruments as well as sample environments to address today and tomorrow's challenges in materials research. The Dynamically Polarized Sample project at the SNS is aimed at taking maximum advantage of polarized neutron scattering from polarized samples, especially biological samples that are abundant in hydrogen. Polarized neutron scattering will allow us drastically increase the signal to noise ratio in experiments such as neutron protein crystallography. The DPS project is near completion and all key components have been tested. Here we report the current status of the project.

36 MATERIALS SCIENCE↗

Precision Polarimetry of Solid HD Photonuclear Targets at LEGS

We have constructed and operated a NMR polarimeter for high-accuracy measurements of hydrogen and deuterium polarization in a frozen-spin solid HD photonuclear physics target. The heart of this polarimeter is a pair of crossed (orthogonal) RF coils that form a transformer that responds only to precessing spins in the sample. We have performed a complete electronic circuit analysis of this crossed coil polarimeter (CC-Meter), and have determined the optimum conditions for its operation. From this analysis, which is confirmed by NMR measurements on hydrogen and deuterium in solid HD, we conclude that the CC-meter can be operated to give a very high signal-to-noise ratio (SNR) for thermal equilibrium polarization while also producing a highly linear response for fully polarized targets. In general, we find that a well-designed and properly constructed CC-Meter can provide a larger SNR at similar nonlinearity, compared to the more commonly used Q-meter. We have used this polarimeter to produce H polarization measurements for a new, high precision determination of the GDH integral for the proton.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

First Experiments with the Polarized Internal Gas Target (PIT) at ANKE/COSY

For future few-nucleon interaction studies with polarized beams and targets at COSY-Juelich, a polarized internal storage-cell gas target was implemented at the magnet spectrometer ANKE. First commissioning of the polarized Atomic Beam Source (ABS) at ANKE was carried out and some improvements of the system have been done. Storage-cell tests to determine the COSY beam dimensions have been performed. Electron cooling combined with stacking and stochastic cooling have been studied. Experiments with N{sub 2} gas in the storage cell to simulate the background produced by beam interaction with the aluminum cell walls were performed to investigate the beam heating by the target gas. The analysis of the d-vectorp-vector->dp and d-vectorp-vector->(dp{sub sp})pi{sup 0} reactions showed that events from different positions of the extended target can be clearly identified in the ANKE detector system. The polarization of the atomic beam of the ABS, positioned close to the strong dipole magnet D2 of ANKE, was tuned with a Lamb-shift polarimeter (LSP) beneath the target chamber. With use of the known analyzing powers of the quasi-free np->dpi{sup 0} reaction, the polarization in the storage cell was measured to be Q{sub y} = 0.79+-0.07 in the vertical stray field of the D2 magnet acting as a holding field. The target thickness achieved was 2x10{sup 13} atoms/cm{sup 2} for one hyperfine state populated in the ABS beam only. With a COSY beam intensity of 6x10{sup 9} stored polarized deuterons in the ring, the luminosity for double polarized experiments was 1x10{sup 29} cm{sup -2} s{sup -1}.

43 PARTICLE ACCELERATORS↗