SEARCH · Search NASA
Results for “EFFECTIVE MASS”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Reliable density functional calculations for the electronic structure of thermoelectric material ZnSb
In this paper, we present the results of systematic test calculations for the electronic structure of thermoelectric material ZnSb using a first-principles full-potential all electron computational method. We used a linear combination of atomic orbitals (LACO) formalism, based on density functional theory (DFT). The exchange-correlation interaction potential of the many electron system was described by using a generalized gradient approximation (GGA). We compared the calculated indirect and direct band gaps as well as the effective masses of holes and electrons in ZnSb with experimental measurement results. The calculated indirect band gap of ZnSb is 0.56 eV, which agrees very well with the experimentally measured values of 0.50 eV ~ 0.61 eV. The calculated direct band gap at X point is 0.89 eV. The calculated effective masses of electrons and holes in ZnSb also agree with experimental data. The systematical test calculations as well as the comparisons of the calculated results with experimental measurements show that the obtained electronic structure of ZnSb would be reliable. We did not observe a major deficiency of the first-principles DFT calculation for the electronic structure of ZnSb, using full-potential all electron LACO method. The reported electronic structure of single crystal ZnSb from this work may provide a fundamental knowledge base for further research and applications for this important thermoelectric material.
Axis dependent conduction polarity in the air-stable semiconductor, PdSe 2
Axis-dependent conduction polarity (ADCP) is a unique electronic phenomena in which the charge polarity of carrier conduction can differ from p-type to n-type depending on the direction of travel through the crystal. Most materials that exhibit ADCP are metals, and very few semiconducting materials exhibit this effect. Here, in this work, we establish that PdSe 2 , a ~0.5 eV band gap semiconductor that is air- and water-stable, exhibits ADCP, through the growth and characterization of the transport properties of crystals with extrinsic p- and n-type doping levels of Ir and Sb, respectively, in the 10 16 –10 18 cm –3 range. Electron doped PdSe 2 exhibits p-type conduction in the cross-plane direction and n-type conduction along the in-plane directions above an onset temperature of 100–200 K that varies with doping level. Lightly p-doped samples show p-type thermopower in all directions at low temperatures, but above ~360 K the in-plane thermopower turns negative. Density functional theory calculations indicate that the origin of ADCP arises from the complementary effective mass anisotropies in the valence and conduction bands in this material, which facilitate hole transport in the cross-plane direction, and electron transport along the in-plane directions. ADCP occurs at temperatures with sufficient thermal population of both carrier types to overcome the extrinsic doping levels to exploit the effective mass anisotropy. In total, the development of this stable semiconductor in which thermally or optically excited holes and electrons inherently migrate along different directions opens up numerous potential applications in a multitude of technologies.
Solid state cloaking for electrical charge carrier mobility control
An electrical mobility-controlled material includes a solid state host material having a controllable Fermi energy level and electrical charge carriers with a charge carrier mobility. At least one Fermi level energy at which a peak in charge carrier mobility is to occur is prespecified for the host material. A plurality of particles are distributed in the host material, with at least one particle disposed with an effective mass and a radius that minimize scattering of the electrical charge carriers for the at least one prespecified Fermi level energy of peak charge carrier mobility. The minimized scattering of electrical charge carriers produces the peak charge carrier mobility only at the at least one prespecified Fermi level energy, set by the particle effective mass and radius, the charge carrier mobility being less than the peak charge carrier mobility at Fermi level energies other than the at least one prespecified Fermi level energy.
Effect of mass flow rate on gas propagation after vacuum break in a liquid helium cooled tube
Vacuum break in particle accelerators is a major concern due to risks associated with personnel and extensive equipment damage. Continuing research in our lab focuses on the sudden loss of vacuum in the liquid helium cooled beam-line tubes of superconducting particle accelerators. In our previous research, we studied nitrogen gas propagation in a uniform tube system immersed in both normal helium (He I) and superfluid helium (He II). It was observed that He II has a stronger effect in slowing down the gas propagation compared to He I, but this effect was largely due to the variation of the point where condensation and deposition of the nitrogen gas on the tube inner wall. Here, we discuss our modifications to the tube system that now allow us to accurately control the starting location of gas condensation in both the He I and He II experiments. Systematic studies of gas propagation were conducted using this new tube system by varying the nitrogen mass flow rate at the tube inlet.
The effects of the chemical composition and strain on the electronic properties of GaSb/InAs core-shell nanowires
The effects of the chemical composition and strain on the electronic properties of [111] zinc-blende (ZB) and [0001] wurtzite (WZ) GaSb/InAs core-shell nanowires (NWs) with different core diameters and shell thicknesses are studied using first-principles methods. The band structures of the [111] ZB GaSb/InAs core-shell NWs underwent a noticeable type-I/II band alignment transition, associated with a direct-to-indirect band gap transition under a compressive uniaxial strain. The band structures of the [0001] WZ GaSb/InAs core-shell NWs preserved the direct band gap under either compressive or tensile uniaxial strains. In addition, the band gaps and the effective masses of the carriers could be tuned by their composition. For the core-shell NWs with a fixed GaSb-core size, the band gaps decreased linearly with an increasing InAs-shell thickness, caused by the significant downshift of the conduction bands. For the [111] ZB GaSb/InAs core-shell NWs, the calculated effective masses indicated that the transport properties could be changed from hole-dominated conduction to electron-dominated conduction by changing the InAs-shell thickness.
Condensed Antenna Structural Models for Dynamics Analysis
Condensed degree-of-freedom models are compared with large degree-of-freedom finite-element models of a representative antenna-tipping and alidade structure, for both locked and free-rotor configurations. It is shown that: (1) the effective-mass models accurately reproduce the lower-mode natural frequencies of the finite element model; (2) frequency responses for the two types of models are in agreement up to at least 16 rad/s for specific points; and (3) transient responses computed for the same points are in good agreement. It is concluded that the effective-mass model, which best represents the five lower modes of the finite-element model, is a sufficient representation of the structure for future incorporation with a total servo control structure dynamic simulation.
The Speed of Light and the Hubble parameter: The Mass-Boom Effect
We prove here that Newton's universal gravitation and momentum conservation laws together reproduce Weinberg's relation. It is shown that the Hubble parameter H must be built in this relation, or equivalently the age of the Universe t. Using a wave-to-particle interaction technique we then prove that the speed of light c decreases with cosmological time, and that c is proportional to the Hubble parameter H. We see the expansion of the Universe as a local effect due to the LAB value of the speed of light co taken as constant. We present a generalized red shift law and find a predicted acceleration for photons that agrees well with the result from Pioneer 10/11 anomalous acceleration. We finally present a cosmological model coherent with the above results that we call the Mass-Boom. It has a linear increase of mass m with time as a result of the speed of light c linear decrease with time, and the conservation of momentum mc. We obtain the baryonic mass parameter equal to the curvature parameter, {omega}{sub m} {omega}{sub k}, so that the model is of the type of the Einstein static, closed, finite, spherical, unlimited, with zero cosmological constant. This model is the cosmological view as seen by photons, neutrinos, tachyons etc. in contrast with the local view, the LAB reference. Neither dark matter nor dark energy is required by this model. With an initial constant speed of light during a short time we get inflation (an exponential expansion). This converts, during the inflation time, the Planck's fluctuation length of 10{sup -33} cm to the present size of the Universe (about 10{sup 28} cm, constant from then on). Thereafter the Mass-Boom takes care to bring the initial values of the Universe (about 10{sup 15} gr) to the value at the present time of about 10{sup 55} gr.
Effective photon mass and exact translating quantum relativistic structures
Using a variation of the celebrated Volkov solution, the Klein-Gordon equation for a charged particle is reduced to a set of ordinary differential equations, exactly solvable in specific cases. The new quantum relativistic structures can reveal a localization in the radial direction perpendicular to the wave packet propagation, thanks to a non-vanishing scalar potential. The external electromagnetic field, the particle current density, and the charge density are determined. The stability analysis of the solutions is performed by means of numerical simulations. The results are useful for the description of a charged quantum test particle in the relativistic regime, provided spin effects are not decisive.
Sub-band-gap absorption in Ga 2 O 3
β-Ga 2 O 3 is a transparent conducting oxide that, due to its large bandgap of 4.8 eV, exhibits transparency into the UV. However, the free carriers that enable the conductivity can absorb light. We study the effect of free carriers on the properties of Ga 2 O 3 using hybrid density functional theory. The presence of free carriers leads to sub-band-gap absorption and a Burstein-Moss shift in the onset of absorption. We find that for a concentration of 10 20 carriers, the Fermi level is located 0.23 eV above the conduction-band minimum. This leads to an increase in the electron effective mass from 0.27–0.28 m e to 0.35–0.37 me and a sub-band-gap absorption band with a peak value of 0.6 × 10 3 cm –1 at 3.37 eV for light polarized along the x or z direction. Both across-the-gap and free-carrier absorption depend strongly on the polarization of the incoming light. We also provide parametrizations of the conduction-band shape and the effective mass as a function of the Fermi level. β-Ga 2 O 3 exhibits very good electronic conductivity in spite of its bandgap of 4.8 eV; this large gap makes it transparent into the UV. This combination allows for applications in devices such as deep-UV blind detectors and contacts for solar cells. It also enables high-power devices, such as high-voltage metal-semiconductor field-effect transistors and Schottky barrier diodes.
Candidate Inorganic Photovoltaic Materials from Electronic Structure-Based Optical Absorption and Charge Transport Proxies
Approximately 33,000 valence-precise, ordered inorganic compounds tabulated in the Inorganic Crystal Structure Database have been screened for their potential as photovoltaic (PV) absorbers. This has been accomplished through the use of proxies for charge carrier mobilities and optical absorption properties from electronic structure calculations, in addition to constraints on thermodynamic stability. Preliminary screening of computed properties tabulated in the Materials Project Database, with subsequent high(er)-fidelity electronic structure calculations of optical properties and band gap corrections, indicates ≈200 known compounds on or near the convex hull which exhibit spectroscopic limited maximum efficiency (SLME) in excess of 25% for a 500 nm thin film, in addition to possessing low effective masses for both electrons and holes. Among the predicted high performers are nearly all the typical commercial inorganic thin-film PV materials and several previously unexplored candidates. The new candidates are drawn from a diverse set of chemical and structural families, including many chalcogenides and pnictides as well as antiperovskites, skutterudites, and semiconducting intermetallics. Here, carrier effective masses, SLME, corrected band gaps, and other relevant information for ≈800 compounds are made available for further analyses via the Materials Project MPContribs Framework.
High-pressure phase of CrS b 2 : A new quasi-one-dimensional itinerant magnet with competing interactions
We have synthesized the high-pressure form of CrSb 2 with CuAl 2 -type structure under 7 GPa and 700 °C, and characterized its structural, transport, and magnetic properties by a suite of measurement techniques over a broad range of temperature, magnetic field, and pressure. In addition to previously reported ferromagnetic (FM) transition at T C ≈160 K, we determine another antiferromagnetic spin-density-wave (SDW) transition at T s ≈90 K, which is characterized by FM sheets of spins in the ab plane that vary along the c axis as determined by neutron powered diffraction. Pronounced anomalies around these two magnetic transitions are visible only in the lattice parameter c, signaling a strong spin-lattice coupling along the -Cr-Cr-Cr- infinite linear chain. We infer that the application of magnetic field can suppress the SDW phase and stabilize the FM state down to the lowest temperature above μ 0 H c ≈3 T, around which a peculiar non-Fermi-liquid behavior with reduced effective mass emerges. However, the application of high pressure induces complex evolution of the magnetic states, i.e., the FM order is lowered while the SDW order is enhanced quickly until they merge together into a single antiferromagnetic transition, which is suppressed completely at P c ≈9 GPa. We observe near Pc non-Fermi-liquid behavior and enhancement of effective mass, which indicates the possible occurrence of magnetic quantum critical point. No superconductivity was observed down to 2 K around Pc.
Radiation response of inorganic scintillators: Insights from Monte Carlo simulations
The spatial and temporal scales of hot particle thermalization in inorganic scintillators are critical factors determining the extent of second- and third-order nonlinear quenching in regions with high densities of electron-hole pairs, which, in turn, leads to the light yield nonproportionality observed, to some degree, for all inorganic scintillators. Therefore, kinetic Monte Carlo simulations were performed to calculate the distances traveled by hot electrons and holes as well as the time required for the particles to reach thermal energy following γ-ray irradiation. CsI, a common scintillator from the alkali halide class of materials, was used as a model system. Two models of quasi-particle dispersion were evaluated, namely, the effective mass approximation model and a model that relied on the group velocities of electrons and holes determined from band structure calculations. Both models predicted rapid electron-hole pair recombination over short distances (a few nanometers) as well as a significant extent of charge separation between electrons and holes that did not recombine and reached thermal energy. However, the effective mass approximation model predicted much longer electron thermalization distances and times than the group velocity model. Comparison with limited experimental data suggested that the group velocity model provided more accurate predictions. Nonetheless, both models indicated that hole thermalization is faster than electron thermalization and thus is likely to be an important factor determining the extent of third-order nonlinear quenching in high-density regions. The merits of different models of quasi-particle dispersion are also discussed.
The effects of mass flow on the temperature and abundance structure of the solar transition region
The density and temperature structure of a multicomponent plasma consisting of electrons, protons, ionized helium, and a trace minor ion species are computed. The equations of force and energy balance for this model are developed and solved. It is found that in the case of downflows the minor ion temperature can be significantly hotter than the electron temperature, and significant abundance enhancements are possible due to the slowdown of the minor species from the effect of the thermal force. A simple physical picture of the source of the thermal force is given.
Experimental measurement of the effective contact angle for solvent/packing interactions in a structured packed column for CO 2 capture
The contact angle is a critical factor for determining the effective mass transfer area for carbon dioxide (CO 2 ) capture via the chemical absorption process in a packed column, and thus the overall capture efficiency of the packed column. Many widely used commercial packings involve microscale features (perforation, corrugation, etc.) that may also affect the wetting behavior. This study proposes a systematic method of using a modified Wilhelmy plate to measure the effective contact angle to characterize the solvent and featured packing interaction. In lieu of computational efforts relying on assumptions guided by semi-informed correlation, the proposed method directly measures the effective contact angle as a function of the solvent and packing thermophysical and hydrodynamic properties. The characterization of the effective contact angle is then integrated in the computational fluid dynamics modeling to reduce uncertainty in the prediction of effective mas transfer area. Experiments were conducted for stainless steel coupons using water and aqueous sodium hydroxide (NaOH) solvent for verification of the proposed experimental protocol. The surface tension of the aqueous NaOH solvent was altered using surfactant and antifoam. The effective contact angle increases with the increased value of the surface tension for flat stainless steel sheets. On the other hand, effective contact angles do not vary in Mellapak coupons for aqueous monoethanolamine (MEA) and NaOH solvent. In this case, surface textures and sheet design play a dominant role in the surface tension of solvents. Furthermore, CO 2 loading has a significant effect on the contact angle for Mellapak coupons. As expected, the contact angle decreases with the increasing temperature of CO 2 capture solvents (MEA, EEMPA). The effective contact angle measurement using the Wilhelmy plate method can provide more accurate and efficient solvents for characterizing the solvent-packing surface interactions. Subsequently, the present method enhances the accuracy of the prediction of the effective mass transfer area in carbon capture by solvent absorption.
An Impulse-Momentum Method for Calculating Landing-Gear Contact Conditions in Eccentric Landings
An impulse-momentum method for determining impact conditions for landing gears in eccentric landings is presented. The analysis is primarily concerned with the determination of contact velocities for impacts subsequent to initial touchdown in eccentric landings and with the determination of the effective mass acting on each landing gear. These parameters determine the energy-absorption requirements for the landing gear and, in conjunction with the particular characteristics of the landing gear, govern the magnitude of the ground loads. Changes in airplane angular and linear velocities and the magnitude of landing-gear vertical, drag, and side impulses resulting from a landing impact are determined by means of impulse-momentum relationships without the necessity for considering detailed force-time variations. The effective mass acting on each gear is also determined from the calculated landing-gear impulses. General equations applicable to any type of eccentric landing are written and solutions are obtained for the particular cases of an impact on one gear, a simultaneous impact on any two gears, and a symmetrical impact. In addition a solution is presented for a simplified two-degree-of-freedom system which allows rapid qualitative evaluation of the effects of certain principal parameters. The general analysis permits evaluation of the importance of such initial conditions at ground contact as vertical, horizontal, and side drift velocities, wing lift, roll and pitch angles, and rolling and pitching velocities, as well as the effects of such factors as landing gear location, airplane inertia, landing-gear length, energy-absorption efficiency, and wheel angular inertia on the severity of landing impacts. -A brief supplementary study which permits a limited evaluation of variable aerodynamic effects neglected in the analysis is presented in the appendix. Application of the analysis indicates that landing-gear impacts in eccentric landings can be appreciably more severe than impacts in symmetrical landings with the same sinking speed. The results also indicate the effects of landing-gear location, airplane inertia, initial wing lift, side drift velocity, attitude, and initial rolling velocity on the severity of both initial and subsequent landing-gear impacts. A comparison of the severity of impacts on auxiliary gears for tricycle and quadricycle configurations is also presented.
Chemical potential and compressibility of quantum Hall bilayer excitons,.
I consider a system of two parallel quantum Hall layers with total filling factor 0 or 1. When the distance between the layers is small enough, electrons and holes in opposite layers can form inter-layer excitons, which have a finite effective mass and interact via a dipole-dipole potential. I present results for the chemical potential u of the resulting bosonic system as a function of the exciton concentration n and the interlayer separation d. I show that both u and the interlayer capacitance have an unusual nonmonotonic dependence on d, owing to the interplay between an increasing dipole moment and an increasing effective mass with increasing d. Finally, I discuss the transition between the superfluid and Wigner crystal phases, which is shown to occur at d x n-1/10. Results are derived first via simple intuitive arguments, and then verified with more careful analytic derivations and numeric calculations.
Intersubband absorption of silicon-based quantum wells for infrared imaging
The 10-micron intersubband absorption in quantum wells made of the silicon-based system, Si/Si(1-x)Ge(x), has been calculated. The necessary details of the effective-mass anisotropy are included in the present analysis. It is found that it is readily possible to achieve an absorption constant of order of 10,000/cm in Si quantum wells with current doping technology. For 110-line and 111-line growth directions, a further advantage of Si quantum wells is pointed out, namely, an allowed absorption at normal incidence due to the anisotropic effective mass in Si.