SEARCH · Search NASA

Results for “EV modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1984

First measurements of supersonic polar wind in the polar magnetosphere

Measurements from the Retarding Ion Mass Spectrometer on the Dynamics Explorer have, for the first time, revealed a supersonic polar wind along polar cap field lines. The observations reported were obtained on the nightside (22:30 to 23:30 MLT) from 65 to 81 deg invariant latitude and at altitudes near 2 earth radii. Fitting the data using a thin-sheath model gives a range of temperatures of 0.1 to 0.2 eV with corresponding flow velocities of 25 to 16 km/s over the estimated range of spacecraft potential of +3 to +5 V. For these values the Mach number ranged from 5.1 to 2.6 (with a most likely value of 3). Characteristics of the H(+) flow are in general agreement with those predicted by 'classical' polar wind theory, but high variabilty of the He(+)/H(+) ratio was observed.

Nagai, T.↗

NASA NTRS1993

The broad-band X-ray spectral variability of Mrk 841

A detailed spectral analysis of five X-ray observations of Mrk 841 with the EXOSAT, Ginga, and ROSAT satellites is reported. Variability is apparent in both the soft (0.1-1.0 keV) and medium (1-20 keV) energy bands. Above, 1 keV, the spectra are adequately modeled by a power law with a strong emission line of equivalent width 450 eV. The large equivalent width of the emission line indicates a strongly enhanced reflection component of the source compared with other Seyferts observed with Ginga. The implications of the results of the analysis for physical models of the emission regions in this and other X-ray bright Seyferts are briefly examined.

George, I. M.↗

NASA NTRS2020

Progress in the Development of Frequency-Domain Multiplexing for the X-ray Integral Field Unit on Board the Athena Mission

Frequency-domain multiplexing (FDM) is the baseline readout system for the X-ray Integral Field Unit on board the Athena mission. Under the FDM scheme, TESs are coupled to a passive LC filter and biased with alternating current (AC bias) at MHz frequencies. Using high-quality-factor LC filters and room-temperature electronics developed at SRON and low-noise two-stage SQUID amplifiers provided by VTT, we have recently demonstrated good performance with the FDM readout of Mo/Au TES calorimeters with Au/Bi absorbers. We have achieved a performance requested for the demonstration model with the single-pixel AC bias ( ΔE = 1.8 eV ) and nine-pixel multiplexing ( ΔE = 2.6 eV ) modes. We have also demonstrated 14-pixel multiplexing with an average energy resolution of 3.3 eV, which is limited by nonfundamental issues related to FDM readout in our laboratory setup.

H. Akamatsu↗

DOE OSTI2020

Improvement of SCALE-XSPROC Multigroup Cross Section Processing Based on the CENTRM Pointwise Slowing Down Calculation

The SCALE-XSProc multigroup (MG) cross section processing procedure based on the CENTRM pointwise slowing down calculation is the primary procedure to process problem-dependent self-shielded MG cross sections and scattering matrices for neutron transport calculations.This procedure supports various cell-based geometries including slab, 1-D cylindrical, 1-D spherical and 2-D rectangular configurations and doubly heterogeneous particulate fuels. Recently, this procedure has been significantly improved to be applied to any advanced reactor analysis covering thermal and fast reactor systems, and to be comparable to continuous energy (CE) Monte Carlo calculations. Some reactivity bias and reaction rate differences have been observed compared with CE Monte Carlo calculations, and several areas for improvement have been identified in the SCALE-XSProc MG cross section processing: (1) resonance self-shielding calculations within the unresolved resonance range, (2) 10 eV thermal cut-off energy for the free gas model, (3) on-the-fly adjustments to the thermal scattering matrix, (4) normalization of the pointwise neutron flux, and (5) fine MG energy structure. This procedure ensures very accurate MG cross section processing for high-fidelity deterministic reactor physics analysis for various advanced reactor systems.

Kim, Kang Seog↗

DOE OSTI2025

Development of a high fidelity CFD model for solvent evaporation and transport in porous structure during battery electrode drying

An efficient battery manufacturing process is the key to the mass production of Electric Vehicles (EV), in which drying is one of the most energy-intensive steps significantly influencing the battery cell performance. An accurate 3D CFD model for drying is essential for predicting the drying mechanism and optimizing its parameters. By optimizing the drying process, it is possible to reduce energy consumption and cost during battery manufacturing, minimize binder loading and maximize active material loading to achieve superior electrochemical performances and facilitate wider and faster public adoption of EV. This project aims to optimize the drying process during electrode manufacturing by leveraging high-fidelity, porous electrode simulations for solvent evaporation. By optimizing this process, we seek to reduce energy consumption during battery manufacturing, while minimizing binder loading and maximizing active material loading, with the overall goal of enhancing electrical vehicle performance.

Horner, Jeffrey Scott [Sandia National Laboratorie↗

NASA NTRS2005

The Physical Nature of the Sharp Spectral Feature at 7 keV Detected in 1H0707-495

XMM-Newton acquired data on the accepted target, 1H0707-495, on 2002 October 13 during revolution 0521. The observation was successful, with only about 5% data loss due to background flaring. We compared the data from this observation with earlier data taken on this Narrow-Line Seyfert 1 about two years before, performing interpretation studies in the context of the partial-covering model. Our second longer observation once again displays a sharp (< 200 eV) spectral drop above 7 keV. However, in comparison to the first observation, the edge depth and energy have changed significantly. In addition to changes in the edge parameters, the high-energy spectrum appears steeper. The changes in the high-energy spectrum can be adequately explained in terms of a partial-covering absorber out-flowing from the central region. The low-energy spectrum also shows significant long-term spectral variability, including (1) a substantial increase in the disk temperature, (2) detection of an approx. 0.9 keV emission feature, and (3) the presence of ionized absorption that was detected during the ASCA mission. The large increase in disk temperature, and the more modest rise in luminosity, can be understood if we consider a slim-disk model for 1H0707-495. In addition, the higher disk luminosity could be the driving force behind the outflow and the re-appearance of an ionized medium during the second XMM-Newton observation.

Brandt, Niel↗

NASA NTRS1979

Physical processes in directed ion beam sputtering

The general operation of a discharge chamber for the production of ions is described. A model is presented for the magnetic containment of both primary and secondary or Maxwellian electrons in the discharge plasma. Cross sections were calculated for energy and momentum transfer in binary collisions between like pairs of Ar, Kr, and Xe atoms in the energy range from about 1 eV to 1000 eV. These calculations were made from available pair interaction potentials using a classical model. Experimental data from the literature were fit to a theoretical expression for the Ar resonance charge exchange cross section over the same energy range. A model was developed that describes the processes of conical texturing of a surface due to simultaneous directed ion beam etching and sputter deposition of an impurity material. This model accurately predicts both a minimum temperature for texturing to take place and the variation of cone density with temperature. It also provides the correct order of magnitude of cone separation. It was predicted from the model, and subsequently verified experimentally, that a high sputter yield material could serve as a seed for coning of a lower sputter yield substrate. Seeding geometries and seed deposition rates were studied to obtain an important input to the theoretical texturing model.

Robinson, R. S.↗

DOE OSTI2020

Joint optimal scheduling for electric vehicle battery swapping-charging system based on wind farms

Insufficiencies in charging facilities limit the broad application of electric vehicles (EVs). In addition, EV can hardly represent a green option if its electricity primarily depends on fossil energy. Considering these two problems, this paper studies a battery swapping-charging system based on wind farms (hereinafter referred to as W-BSCS). In a W-BSCS, the wind farms not only supply electricity to the power grid but also cooperate with a centralized charge station (CCS), which can centrally charge EV batteries and then distribute them to multiple battery swapping stations (BSSs). The operational framework of the W-BSCS is analyzed, and some preprocessing technologies are developed to reduce complexity in modeling. Then, a joint optimal scheduling model involving a wind power generation plan, battery swapping demand, battery charging and discharging, and a vehicle routing problem (VRP) is established. Then a heuristic method based on the exhaustive search and the Genetic Algorithm is employed to solve the formulated NP-hard problem. Numerical results verify the effectiveness of the joint optimal scheduling model, and they also show that the W-BSCS has great potential to promote EVs and wind power.

17 WIND ENERGY↗

DOE OSTI2025

X-ray absorption spectroscopy measurements of radiatively ionized argon gas

X-ray absorption spectroscopy is a diagnostic tool that can characterize the temperature and ionization state of a plasma. This technique requires experiments to characterize the platform, careful data calibration, and comparison with atomic models to understand the plasma parameters. We performed ionizing radiation wave experiments at the OMEGA Laser Facility that used an ∼ 80 eV X-ray source to heat an Argon (Ar) gas cell at fill pressures of 3 atm. To diagnose the Ar plasma, we used a capsule backlighter offset 10 mm from the gas cell, to produce X-rays that were absorbed by the ionized Ar gas. The absorption analysis was calibrated using the significant line structure in the backlighter spectrum, which served as independent energy fiducials enabling definitive measurements of a 50-eV shift in the energy of the Ar K-edge due to ionization. We compare the measured absorption spectra to two independent atomic models, PrismSPECT and SCRAM, and show that the observed K-edge shift in the heated gas is consistent with ionization up to Ar 4+ and temperatures of 10 eV.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2000

The Low Energy Effective Area of the Chandra Low Energy Transmission Grating Spectrograph

The Chandra X-ray Observatory was successfully launched on July 23, 1999, and subsequently began an intensive calibration phase. We present the preliminary results from the in-flight calibration of the low energy response of the High Resolution Camera spectroscopic readout (HRC-S) combined with the Low Energy Transmission Grating (LETG) aboard Chandra. These instruments comprise the Low Energy Transmission Grating Spectrograph (LETGS). For this calibration study, we employ a pure hydrogen non-LTE white dwarf emission model (T = 25000 K and log g = 9.0) for comparison with the Chandra observations of Sirius B. The pre-flight calibration of the LETGS effective area only covered wavelengths shortward of 44 A (E less than 277 eV). Our Sirius B analysis shows that the HRC-S quantum efficiency (QE) model assumed for longer wavelengths leads to an overestimate of the effective area by an average factor of about 1.6. We derive a correction to the low energy HRC-S QE model to match the predicted and observed Sirius B spectra over the wavelength range of 44-185 A. We make an independent test of our results by the comparison of a Chandra LETGS observation of HZ 43 with pure hydrogen model atmosphere predictions and find good agreement.

Pease, D.↗

DOE OSTI2025

Modeling Structured Electrodes and Graded Porosity for Improving Discharge Rate Capability in Ultra-Thick Graphite|LiNi 0.6 Mn 0.2 Co 0.2 O 2 Batteries

Long-range electric vehicles (EVs) require high-energy-density batteries that also meet the power demands of high current charge and discharge. Ultra-thick (>100 μm) Lithium-ion battery electrodes are critical to enable this need, but slow ion transport in conventional uniform electrodes (UEs) reduces battery capacity at increasing charge/discharge rates. We present a 3D computational analysis on the impact of structured electrode (SE) and graded electrode (GE) geometries on the discharge rate capability of ultra-thick graphite|LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC-622) battery cells based on the footprint of a commercial EV pouch cell. SE cathodes with either a “grid” or “line” geometry and GEs with two layers of porosity were modeled. Based on the results of 230 models, we found that the electrolyte volume fraction is a key parameter that impacts capacity improvements in UEs, GEs, and SEs at 2 C–6 C discharge rates. SEs have the greatest discharge rate capability, outperforming GEs and UEs due to reduced Lithium-ion concentration gradients across the electrode thickness, which mitigates electrolyte depletion at high rates. The best SE model has a “grid” geometry with gravimetric and volumetric energy density improvements of 0.9%–4% at C/2–2 C and 18%–24% at 4 C–6 C relative to UEs.

25 ENERGY STORAGE↗

NASA NTRS1972

Vibrational excitation in CO by electron impact in the energy range 10-90 eV.

The ratio of the scattering intensity for the v double prime = 1 excitation to the elastic scattering intensity at 40- and 80-deg scattering angles has been determined for 10- to 90-eV impact energies for electron scattering by CO. These ratio curves exhibit broad peaks near 20-eV impact energy which cannot be accounted for by plane-wave calculations based on potential scattering models. The peaks are indicative of a resonant excitation process (or processes) in the v double prime = 1 channel in the range from 15 to 25 eV.

Chutjian, A.↗

DOE OSTI2025

Resolving the Coverage Dependence of Surface Reaction Kinetics with Machine Learning and Automated Quantum Chemistry Workflows

Microkinetic models for catalytic systems require estimation of many thermodynamic and kinetic parameters that can be calculated for isolated species and transition states using ab initio methods. However, the presence of nearby coadsorbates on the surface can dramatically alter these thermodynamic and kinetic parameters causing them to be dependent on species coverage fractions. As there are combinatorially many coadsorbed configurations on the surface, computing the coverage dependence of these parameters is far less straightforward. We present a framework for generating and applying machine learning models to predict coverage-dependent parameters for microkinetic models. Our toolkit enables automatic calculation and evaluation of coadsorbed configurations allowing us to sample 2,000 coadsorbed adsorbates and transition states (TSs) for a diverse set of 9 reactions on Cu(111), a challenging surface, with four possible coadsorbates. This dataset was then used to train subgraph isomorphic decision trees (SIDTs) to predict the stability and association energy of configurations. We were able to achieve mean absolute errors (MAEs) of 0.106 eV on adsorbates, 0.172 eV on TSs, and due to natural error cancellation in SIDTs for relative properties, 0.130 eV on reaction energies and 0.180 eV on activation barriers. In conclusion, we describe how to use these models to predict coverage-dependent corrections for adsorbates and TSs and demonstrate on H*, HO*, and O* comparing the generated SIDT model with an iteratively refined version.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Dark Energy Survey Year 3 results: Constraints on extensions to Λ CDM with weak lensing and galaxy clustering

We constrain six possible extensions to the Λ cold dark matter (CDM) model using measurements from the Dark Energy Survey’s first three years of observations, alone and in combination with external cosmological probes. The DES data are the two-point correlation functions of weak gravitational lensing, galaxy clustering, and their cross-correlation. We use simulated data vectors and blind analyses of real data to validate the robustness of our results to astrophysical and modeling systematic errors. In many cases, constraining power is limited by the absence of theoretical predictions beyond the linear regime that are reliable at our required precision. The Λ CDM extensions are dark energy with a time-dependent equation of state, nonzero spatial curvature, additional relativistic degrees of freedom, sterile neutrinos with eV-scale mass, modifications of gravitational physics, and a binned σ 8 ( z ) model which serves as a phenomenological probe of structure growth. For the time-varying dark energy equation of state evaluated at the pivot redshift we find ( w p , w a ) = ( - 0.9 9 - 0.17 + 0.28 , - 0.9 ± 1.2 ) at 68% confidence with z p = 0.24 from the DES measurements alone, and ( w p , w a ) = ( - 1.0 3 - 0.03 + 0.04 , - 0. 4 - 0.3 + 0.4 ) with z p = 0.21 for the combination of all data considered. Curvature constraints of Ω k = 0.0009 ± 0.0017 and effective relativistic species N eff = 3.1 0 - 0.16 + 0.15 are dominated by external data, though adding DES information to external low-redshift probes tightens the Ω k constraints that can be made without cosmic microwave background observables by 20%. For massive sterile neutrinos, DES combined with external data improves the upper bound on the mass m eff by a factor of 3 compared to previous analyses, giving 95% limits of ( Δ N eff , m eff ) ≤ ( 0.28 , 0.20 eV ) when using priors matching a comparable Planck analysis. For modified gravity, we constrain changes to the lensing and Poisson equations controlled by functions Σ ( k , z ) = Σ 0 Ω Λ ( z ) / Ω Λ , 0 and μ ( k , z ) = μ 0 Ω Λ ( z ) / Ω Λ , 0 , respectively, to Σ 0 = 0. 6 - 0.5 + 0.4 from DES alone and ( Σ 0 , μ 0 ) = ( 0.04 ± 0.05 , 0.0 8 - 0.19 + 0.21 ) for the combination of all data, both at 68% confidence. Overall, we find no significant evidence for physics beyond Λ CDM .

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2022

Machine learning for impurity charge-state transition levels in semiconductors from elemental properties using multi-fidelity datasets

Quantifying charge-state transition energy levels of impurities in semiconductors is critical to understanding and engineering their optoelectronic properties for applications ranging from solar photovoltaics to infrared lasers. While these transition levels can be measured and calculated accurately, such efforts are time-consuming and more rapid prediction methods would be beneficial. Here, we significantly reduce the time typically required to predict impurity transition levels using multi-fidelity datasets and a machine learning approach employing features based on elemental properties and impurity positions. We use transition levels obtained from low-fidelity (i.e., local-density approximation or generalized gradient approximation) density functional theory (DFT) calculations, corrected using a recently proposed modified band alignment scheme, which well-approximates transition levels from high-fidelity DFT (i.e., hybrid HSE06). Further, the model fit to the large multi-fidelity database shows improved accuracy compared to the models trained on the more limited high-fidelity values. Crucially, in our approach, when using the multi-fidelity data, high-fidelity values are not required for model training, significantly reducing the computational cost required for training the model. Our machine learning model of transition levels has a root mean squared (mean absolute) error of 0.36 (0.27) eV vs high-fidelity hybrid functional values when averaged over 14 semiconductor systems from the II–VI and III–V families. As a guide for use on other systems, we assessed the model on simulated data to show the expected accuracy level as a function of bandgap for new materials of interest. Finally, we use the model to predict a complete space of impurity charge-state transition levels in all zinc blende III–V and II–VI systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Multiprobe constraints on early and late time dark energy

We perform a multiprobe analysis combining cosmic microwave background (CMB) data from Planck and the Atacama Cosmology Telescope (ACT), ACT CMB lensing, and large-scale structure (LSS) measurements from the Dark Energy Spectroscopic Instrument (DESI), including DESI Legacy Imaging Survey (LS) galaxies and baryon acoustic oscillations (BAOs). We present the first 5×2 pt analysis of ACT DR6 lensing, DESI LS, and Planck Integrated Sachs-Wolfe (ISW). Within Λ⁢CDM, this yields 𝑆 8 =𝜎 8 ⁢(Ω 𝑚 /0.3) 0.5 =0.819 ±0.016, in good agreement with primary CMB inferences and provides a sound-horizon-free Hubble constant constraint of 𝐻 0 =70.0±4.4 km s −1 Mpc −1 . Then, combining with CMB primary and BAO, we reconfirm a CMB–BAO discrepancy in the Ω 𝑚 –$\frac{𝐷𝑣}{𝑟𝑑}$ plane, which is heightened when combining BAO with the 5 ×2 pt data vector. We explore two dark-energy extensions that may reconcile this: an early-time modification, early dark energy (EDE), and late-time dynamical dark energy (DDE) parametrized by 𝑤 0 ⁢𝑤 𝑎 . For CMB primary +BAO +5 ×2 pt, we find a 3.3⁢𝜎 preference for DDE over Λ⁢CDM, while EDE is modestly favored at 2.3⁢𝜎. The models address different shortcomings of Λ⁢CDM: DDE relaxes the neutrino mass bound (𝑀 𝜈 <0.17 eV vs <0.050 eV under Λ⁢CDM), making it compatible with neutrino oscillation measurements, while EDE raises the Hubble constant to 𝐻 0 =70.5±1.2 km s −1 Mpc −1 , easing the discrepancy with SH0ES. However, neither model resolves both issues simultaneously. Our analysis indicates that both DDE and EDE remain viable extensions of Λ⁢CDM within current uncertainties and demonstrates the capacity of combined probes to place increasingly stringent constraints on cosmological parameters.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2023

A Finite-Time Ensemble Method for Mixed Layer Model Comparison

Here, this work evaluates the fidelity of various upper-ocean turbulence parameterizations subject to realistic monsoon forcing and presents a finite-time ensemble vector (EV) method to better manage the design and numerical principles of these parameterizations. The EV method emphasizes the dynamics of a turbulence closure multimodel ensemble and is applied to evaluate 10 different ocean surface boundary layer (OSBL) parameterizations within a single-column (SC) model against two boundary layer large-eddy simulations (LES). Both LES include realistic surface forcing, but one includes wind-driven shear turbulence only, while the other includes additional Stokes forcing through the wave-average equations that generate Langmuir turbulence. The finite-time EV framework focuses on what constitutes the local behavior of the mixed layer dynamical system and isolates the forcing and ocean state conditions where turbulence parameterizations most disagree. Identifying disagreement provides the potential to evaluate SC models comparatively against the LES. Observations collected during the 2018 monsoon onset in the Bay of Bengal provide a case study to evaluate models under realistic and variable forcing conditions. The case study results highlight two regimes where models disagree 1) during wind-driven deepening of the mixed layer and 2) under strong diurnal forcing.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

EVI-EnSitePy (Electric Vehicle Infrastructure – Energy Estimation and Site Optimization Tool in Python) [EVI-X Modeling Suite] [SWR-25-07]

EVI-EnSitePy is a comprehensive agent-based tool designed for the analysis and design of high-power charging sites, encompassing a wide array of site agents including Electric Vehicles (EVs), chargers, energy storage units (ESS), renewable energy resources (DER), and loads. This versatile tool offers diverse functionalities and a modular modeling approach, allowing detailed configuration of agents based on power ratings, port numbers, energy capacities, demand requirements, charger interfaces, and flexibility to customize the tool for project specific goals. By simulating agent interactions and employing various metrics, EVI-EnSitePy enables the assessment of site performance, exploration of energy management systems (EMS), and implementation of innovative EV charging policies. Utilizing EV charge schedules and arrival states, the tool performs thorough charging site simulations, with outputs consisting of agent and site-level power profiles and statistical metrics. Employing a tree graph structure, EVI-EnSitePy supports nested site structures and power distribution modeling. The tool's ability to generate charging schedules deterministically or via stochastic analysis further enhances its versatility. Through its features and capabilities, EVI-EnSitePy offers a powerful platform for informed decision-making in the realm of high-power charging site design and operation.

Jackson, Derek [National Renewable Energy Laborato↗