SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Inductive filters against electromagnetic interference are commonly made by winding coils around a magnetic material with high permeability. This permeability should remain high at high frequencies, so that the impedance of the inductor made from it can be large to block off any high frequency EMI signals.
The main purpose of the Avionics Vault is to shield radiation sensitive electronics for the Europa Clipper Spacecraft. The vault is a box structure made out of aluminum panels. The panels are roughly 10 mm thick in order to shield the electronics from the orbital total ionizing radiation around Jupiter. The vault requires an electromagnetic interference (EMI) shielding effectiveness (SE) of at least 70 dB in order to mitigate EMI with the spacecraft radar receiver. Overall, the vault accommodates four main types of penetrations: receptacle connectors, pass-through cables, fluid lines, and vent holes. More than 150 cables penetrate the vault panels to connect to electronic boxes inside. Fluid pipes enter and exit the vault to transfer heat to the rest of the spacecraft. Vent holes provide a path for air to escape from the vault during launch. Several novel penetrations designs were created to meet EMI and radiation shielding requirements. Receptacle connectors interface to the vault panels using 1.3 mm thick Ta10W plates. Pass-through cables penetrate the vault using aluminum clamshells after being wrapped with Teflon cushion tape, Kapton tape, and copper tape. Vent hole penetrations consist of a copper mesh for EMI shielding and an aluminum radiation shield bracket to direct air out of the vault during launch. Fluid lines terminate at the vault wall using mechanical fittings that resemble a nut and bolt interface. In addition, most mechanical seams and penetrations utilize EMI gaskets to ensure proper EMI shielding. To reduce risk and confirm that the vault penetration designs were appropriate for EMI shielding, an EMI chamber at the Jet Propulsion Laboratory (JPL) was used to test a mock-up vault panel with multiple variations of all four main types of vault penetrations. This EMI SE test also incorporated different methods for bundling pass-through cables, and a comparison of flange mounted connectors versus jam nut connectors. A low noise preamplifier and a Rohde & Schwarz spectrum analyzer measured E-field levels transmitting through the mock-up vault panel. The results showed a shielding effectiveness of 77 dB for the mock-up vault panel, which exceeds the 70 dB target for Europa Clipper. Both the flange mounted connectors and jam nut connectors exhibited similar EMI SE results at the measured frequencies, and all variations of vault penetrations showed favorable EMI SE levels. Since the flight panels will be much larger and include many more penetrations, there will be testing of the flight vault to confirm its EMI SE is compliant with environmental requirements.
Spacecraft electronic are affected by the space radiation environment. Among the different types of radiation effects that can affect spacecraft electronics is the single event transient (SET). The space environment is responsible for many of the single event transients which can upset the performance of the spacecraft avionics hardware. In this chapter we first explore the origins of single event transients, then explore the modeling of a single event transient in digital and analog circuit. The chapter also addresses the concept of crosstalk that could develop among digital circuits in the present of a SET event. The chapter also provides a discussion of SET hardening. We then provide a discussion concerning propagation of a single event transient event at the local, subsystem, and system level in a spacecraft using two different models, one of the models developed by the author, known as the state transition model. The final goal of the chapter is to provide a qualitatively methodology for assessing single event transients and its effects so that spacecraft avionics engineers can develop either hardware or software countermeasures in their designs. SET is not a form of electromagnetic interference (EMI) in its origin, but semantically SET is very similar to EMI because they are both caused a current source not previously accounted for. SET has the same effects as EMI and it can cause interference problems in electronic circuits via multiple coupling mechanisms similar to EMI, and therefore makes such circuits incompatible.
Luna has extended the length of its fiber optic shape sensing technology out to a continuous, high-fidelity measurement of a 100-meter sensor, creating a novel concept for a self-monitoring tether for robotic exploration. This tether is capable of measuring its own tension, curvature, and full 3-D shape along its entire length as it is deployed by a robotic rover. Using Optical Frequency Domain Reflectometry (OFDR) and the Rayleigh scatter signature to sense the state of a customized multicore optical fiber, the new technology is lightweight, compact, and immune to electromagnetic interference. Results are presented from tests with a 50-meter tether on the Axel Rover at JPL’s Mars Yard testing ground.
NASA and Meta Vista have been actively working the development of a new type of cryogenic refrigeration cycle, one that uses hydrogen as the working fluid and compresses this hydrogen using an electrochemical hydrogen compressor. This new cycle has many advantages compared to current state of the art. The electrochemical compressor is more efficient than a mechanical compressor. It is a solid-state device with no moving parts, no vibration, and no lubrication requirements. The compressor is powered by direct current, so there is no Electromagnetic Interference (EMI). The power systems integration will be simpler and more efficient than typical space cryocooler power systems.
A scalable, compact oven testbed system for simultaneously evaluating a multitude of high temperature integrated circuits (ICs) for prolonged operating times of up to 600 °C has been prototyped. The new testbed system enables long-duration high temperature testing in sufficient statistical quantities consistent with standard aerospace electronics engineering standards. This setup is comprised of multiple compact ovens housing chips or packages mounted to ceramic circuit boards. Each oven is a compact 15.2 cm length by 15.2 cm width by 12.7 cm depth with a maximum 400 Watts of heating power. The custom-made silicon oxide ceramic heating block inside each oven is based on a 3D printed design adapted for the easy insertion of the IC device under test (DUT). This innovative design provides the quick insertion of ICs with or without a ceramic package into a 600 °C environment by utilizing a movable 11.43 cm long ceramic substrate with electrical traces extending from the oven hot zone to external standard plastic-based board connectors. Another key oven design feature is the minimization of the DUT exposure to electromagnetic interference (EMI) by utilizing a filtered DC power source to reduce heating element noise. Additionally, the ovens can be configured in a parallel arrangement allowing global data monitoring over a single industrial RS422 serial port. This feature is important for scaling up to test multiple ICs semi-simultaneously. A USB serial port is provided to independently control the operating parameters of each oven such as the oven target temperature and oven ramp rate. The oven temperature can reach up to 600 °C with a confirmed +/- 4 °C maximum deviation across the test zone region. The ramp rate can be programmed from 1 °C/minute up to 10 °C/minute. Furthermore, a programmable switchboard is used to interface with the DUT. This switchboard comprises a National Instruments Peripheral Component Interconnect eXtension for Instrumentation (NI PXI) system and a breakout board to send and receive power, analog or digital test signals. By using this unique oven testbed system, a variety of ICs can now be tested in parallel using the same test components configured for a diverse set of requirements.
Computing capabilities of space systems have in-creased onboard performance by orders of magnitude with the use of radiation-tolerant field-programmable gate arrays (FPGA)and processors. The incorporation of signal and power integrity analysis with printed circuit board (PCB) design in reliable computing architectures for space systems has become critical to enable future mission capabilities. Developers launch high-performance processors into a breadth of orbits and missions, running varying applications that create challenges for designing reliable computing hardware. Specifically, for these designs, academic and industry research has focused on component radiation performance, fault mitigation, and reliable architectures. How-ever, other design parameters including electromagnetic interference (EMI), PCB stackup, signal integrity (SI), voltage regulator module (VRM) design, and power distribution network (PDN)are often deprioritized or disregarded as the design matures. Since these characteristics are becoming more significant in high-performance processor designs, this research presents a hardware design and analysis methodology for high-performance, space-computing systems that focuses on a holistic design approach and PDN reliability. While these challenges exist across all space hardware, the reduced PCB dimensions imposed by SmallSats and CubeSats introduce additional hurdles, specifically to VRM and decoupling design. By examining the relationship between the PDN and radiation performance, an analytical relationship is developed that incorporates Total Ionizing Dose and Single-Event Transients to ensure reliability throughout the mission duration. The presented design methodology is applied to the SpaceCube v3.0 Mini, an FPGA-based on-board science data processing system developed at NASA Goddard Space Flight Center.
A hardware fault in aerospace is an undesired response to a designed engineering function in hardware. Therefore, in aerospace systems fault management is of prime importance. An important aspect of hardware faults is fault propagation. Fault propagation (also known as failure propagation) is a condition where a fault will not only produce an undesired hardware response, at its location of origin, but the fault will also propagate to other interfaced hardware and cause additional faults, or failures. Fault containment is necessary to avoid fault propagation. A fault containment region is an electronic or electromechanical region within a given hardware assembly where a fault in that region will not physically propagate to other regions of the assembly, and beyond. Rather, the fault will cause a functional failure of the hardware, where the fault occurred, without causing any additional propagated failures. Electromagnetic Compatibility (EMC) is a desired state in aerospace hardware. Electromagnetic Interference (EMI) in aerospace hardware is a fault condition of EMC. Like other faults EMI can also propagate to other aerospace hardware unless it occurs inside an EMI containment region. The paper addresses the concepts of fault containment region and introduces the concept of EMI containment region with examples of both.
The occurrence of faults in aerospace system hardware and software have consequences ranging from minor effects to catastrophic effects, and such faults can directly affect the safety of hardware and personnel. There are many origins to fault conditions, and the hardware that is capable of still meeting its performance requirements after experiencing itself a fault is said to be fault tolerant. A fault tolerant hardware is capable of detecting, isolating, and recovering from a fault condition; and this is a subfield of control engineering. An aerospace system that has been shown to have electromagnetic compatibility (EMC) in all its subsystems and systems cannot induced faults caused by electromagnetic interference (EMI). It can be proposed that the presence of EMI (or lack of EMC) is analogous to a potential fault initiator and the effects can likewise range from minor to severe. This paper starts by addressing the consequences of hardware failure in aerospace systems from a fault perspective, because the design of fault tolerant system is a major endeavor in aerospace. To arrive to this goal the paper starts with the concepts of fault, fault propagation, and a new concept called fault containment region. The paper then proceeds to provide two very recent examples in the aircraft industry of fault propagation with catastrophic effects. The paper proceeds to introduce the concept of EMI fault containment and a brief introduction to another new concept called the EMI containment region. The paper proceeds with an example of EMI fault containment region. The paper ends with a lesson learned conclusions.
NASA's Mars 2020 Rover—with a launch window opening July 2020, and landing expected February 2021—has mission objectives to look for evidence of habitability, seek biosignatures of past life, collect and cache samples for possible future return to Earth, and prepare for future human missions. The Rover platform is similar to the previous Mars Science Laboratory (MSL) “Curiosity” rover that landed in 2012 but contains a new suite of scientific instruments and upgrades to existing functionality. The scientific payload includes a trio of chemical analysis tools (PIXL, SHERLOC, SuperCam), a ground penetrating radar (RIMFAX), an upgraded weather station (MEDA), upgraded high resolution camera (MastCam-Z), and an oxygen-producing experiment (MOXIE). These changes—along with new efficiency goals to operate more Rover subsystems concurrently and thus collect more science—presented new electromagnetic compatibility (EMC) challenges. In this paper, we will describe the campaign to ensure Mars 2020 mission success from an electromagnetic environment perspective: 1) confirming existing MSL heritage subsystems and EMC requirements were compatible with the new Mars 2020 mission objectives, 2) engaging with engineers and scientists early in the project to identify and evaluate risks before hardware assembly and performing ambitious risk reduction tests, 3) undertaking a comprehensive subsystem qualification test program based on tailored MIL-STD-461F requirements, occasionally leading to redesign, 4) synthesizing the data collected to perform detailed analyses toward the goal of making risk-informed decisions at a system level. The spacecraft has successfully completed all three planned system level tests, demonstrating self-compatibility with minimal impact to operations from electromagnetic interference in all mission phases.
The newly patented micro-multilayer multifunctional electrical insulation (MMEI) system was developed for future electric aircraft applications which critically require lightweight but high voltage (HV), high temperature, and corona or partial discharge (PD) resistant insulation. During the initial development stages, the concept and practicability of the MMEI system were successfully validated with its exceptionally high dielectric breakdown voltages. The multilayer structures were optimized in terms of material type, individual layer thickness, and overall layer configuration along with potential mechanisms identified for its superior performance. Subsequently, scalability, manufacturability, and commercial applicability of the MMEI system were demonstrated with the 1 meter long, 3-phase HV, high power (HP) bus bar prototypes. Two prototypes, one with the conventional SOA insulation system including Mica sheet and the other with an optimized MMEI, were designed, fabricated, and tested successfully. Both prototypes passed both HiPot and PD tests up to the highest test voltage available, 15 kVAC, although the latter showed a slight increase in PD activities at 12.5 kV. However, the prototype with MMEI was 15% lighter or 12% thinner than the other one. Current efforts to significantly enhance the PD resistance of the MMEI system by employing semiconductive shielding layers, which can be also multifunctional, e.g., electromagnetic interference shielding, moisture blocking, heat dissipation, for various HV applications are also discussed in this paper.
The Exploration Medical Capability (ExMC) element aims to provide astronauts with the means for their own health monitoring, diagnosis, and treatment during exploration missions. As space flight ventures further from earth, the need for autonomous medical care increases under greater constraints on size, mass, and resources. One pillar for diagnosis that crew would be separated from is laboratory analysis. Even now on ISS, blood samples must be collected and returned to earth for testing. In response, ExMC is assessing how assays for hematology, bone health, radiation exposure etc. could be addressed through commercial-off-the-shelf (COTS) and Small Business Innovation Research (SBIR) funded bioanalyzers that are miniaturizing lab technology. Since missions will reach distances where there are no timely replacements, validation on the International Space Station (ISS) is a necessary part of that assessment. In partnership with NASA Johnson Space Center (JSC) Immunology Lab and the Research Operations and Integration (ROI) element, ExMC conducted a technology demonstration on ISS of the rHEALTH ONE, a flow cytometry based bioanalyzer, to assess future devices based on this design. In flow cytometry, there are predominantly three ways to focus the cells (or particles) into a single file stream: hydrodynamic focusing, microcapillary, and acoustic focusing. The rHEALTH ONE utilizes the commercial standard, sheath-based hydrodynamic focusing. rHEALTH itself represents both a company and a suite of medical tools NASA has funded through SBIR grants towards the development of a promising diagnosis instrument for exploration missions. rHEALTH ONE is the interim version of the technology, functional as a benchtop analyzer and test bed for the next generation of rHEALTH in development. Several modifications were made to the rHEALTH ONE analyzer for operation in microgravity. For function, fluid management was key. A sheath-based analyzer uses sheath fluid to flow the sample, cleaning fluid to prevent biological contamination, and a reservoir to collect the liquid waste. The rHEALTH ONE analyzer uses bottles dependent on gravity to separate the air and liquid pathways and keep the liquids contained. It uses only 1 psig of air pressure to directly push the liquid through the device, requiring little-to-no resistance at inlet and outlet. A microtubing assembly with self-sealing luer connectors was designed – featuring 0.014 mm thick durable medical balloons to hold water inside the supply bottles – to create safe containment and easy access for the crew while maintaining the analyzer’s function. For safety, copper tape was added to the interior of the plastic housing to reduce electromagnetic interference, fluid and electrical connections were secured against vibration and leaks, and gaps were further sealed to ensure containment of the optical block and lasers. Water as the sheath and cleaning fluid and TOX 0 samples were used to reduce the biohazard risk to the crew. In May 2022, European Space Agency astronaut Samantha Cristoforetti demonstrated the rHEALTH ONE aboard ISS for its sample loading, flow cytometry, and data collection capability in microgravity. The JSC Immunology Lab provided flow cytometry expertise, designed the sample test protocol, and manufactured and benchmarked the flight samples on a ‘gold-standard’ flow cytometer. The analyzer was primed with water, purged of air, and four calibration solutions of polystyrene microparticles were tested to characterize its performance. Tightly controlled procedures and excellent execution prevented air bubble interference during air/water separation, fluid transfer, sample mixing and loading. Data showed a slight increase in signal noise on 3 of 5 channels and an anomaly of fluorophores migrating in one sample (confirmed by JSC post-flight). Flight results correctly detected the change in sample, matched the analyzer’s ground performance, and were consistent with the gold-standard’s ground results. Although areas were noted for improvement, these outcomes signified complete mission success.
Optical frequency domain reflectometer (OFDR) systems provide for the interrogation of hundreds of fiber Bragg gratings (FBGs) within a single optical fiber. The coupling of FBG sensors to an OFDR interrogator results in a highly distributed measurement system utilizing sensors that are lightweight, immune to electromagnetic interference, and low-profile. This paper presents and explores a basic derivation of OFDR-FBG signals, the processing of those signals, the assembly of a basic OFDR system, an example measurement scenario, and the effects of specific component and configuration changes on interrogator speed, resolution, and accuracy.
A type of Feed-Through Electromagnetic Interference (EMI) Filter incorporating two discoidal (ring-shaped) capacitors was selected for use in the Europa Clipper spacecraft propulsion systems. Parts reliability specialists were aware of historical problems with the attach materials used to provide mechanical support and electrical contact within these devices, so therefore a screening was desired to ensure the longevity and ruggedness of units intended for the space environment. CT X-ray, a technology which has become more widely available thanks to the compelling depth of information it offers, was selected as the inspection method of choice.
The newly patented micro-multilayer multifunctional electrical insulation (MMEI) system was developed for future electric aircraft applications which critically require lightweight but high voltage (HV), high temperature, and corona or partial discharge (PD) resistant insulation. During the initial development stages, the concept and practicability of the MMEI system were successfully validated with its exceptionally high dielectric breakdown voltages. The multilayer structures were optimized in terms of material type, individual layer thickness, and overall layer configuration along with potential mechanisms identified for its superior performance. Subsequently, scalability, manufacturability, and commercial applicability of the MMEI system were demonstrated with the 1 meter long, 3-phase HV, high power (HP) bus bar prototypes. Two prototypes, one with the conventional SOA insulation system including Mica sheet and the other with an optimized MMEI, were designed, fabricated, and tested successfully. Both prototypes passed both HiPot and PD tests up to the highest test voltage available, 15 kVAC, although the latter showed a slight increase in PD activities at 12.5 kV. However, the prototype with MMEI was 15% lighter or 12% thinner than the other one. Current efforts to significantly enhance the PD resistance of the MMEI system by employing semiconductive shielding layers, which can be also multifunctional, e.g., electromagnetic interference shielding, moisture blocking, heat dissipation, for various HV applications are also discussed in this paper.
(16) Psyche is a metallic asteroid located in the asteroid belt between Mars and Jupiter. The composition of Psyche is unknown, but the scientific community believes it is composed primarily of iron, nickel, and silicates. The Psyche mission will be the first space mission to study this asteroid in close proximity, and as such, determining the elemental composition of the asteroid is one of the primary objectives of this mission. The spacecraft measures this elemental composition using the Gamma Ray Spectrometer (GRS), which detects cosmic-ray induced gamma rays from Psyche’s surface. In addition to gamma rays from Psyche, the GRS will also detect background gamma rays from spacecraft material nearby the GRS. Because Ni is such a key element for achieving the mission science objectives, a special effort has been made to minimize background gamma rays from Ni, thus maximizing sensitivity to the Ni gamma rays from Psyche. The Psyche mission approached this potential Ni background issue with two methods, locating the GRS away from the spacecraft/source of Ni and setting a threshold requirement against the total Ni mass of the spacecraft. Verifying that the total amount of Ni on the spacecraft is within this threshold is thus a key part of ensuring the GRS can meet its science objectives. Ni alloys are commonly used on spacecraft, but the mass and location of elemental Ni is not typically accounted for. Ni can be found in many materials all over the spacecraft – in fasteners, optical assemblies, magnetic shields, electromagnetic interference (EMI) tape, under gold plating, in connectors, and so on. The task proved further challenging because of the distributed nature of the build of this spacecraft and the use of vendors external to JPL. While the analysis was atypical and source information difficult to cull, the approach described in this paper used tools and data available to the project in some form to achieve this goal. For Psyche, current analysis shows there is margin in meeting the Ni mass requirement. This paper explains the systematic approach used to accurately and precisely record Ni content on the Psyche spacecraft. While this approach was defined for Ni on the Psyche mission, it can be used for any future project with the need to accurately estimate the total mass of a single element or material on a spacecraft.
(16) Psyche is a metallic asteroid located in the asteroid belt between Mars and Jupiter. The composition of Psyche is unknown, but the scientific community believes it is composed primarily of iron, nickel, and silicates. The Psyche mission will be the first space mission to study this asteroid in close proximity, and as such, determining the elemental composition of the asteroid is one of the primary objectives of this mission. The spacecraft measures this elemental composition using the Gamma Ray Spectrometer (GRS), which detects cosmic-ray induced gamma rays from Psyche’s surface. In addition to gamma rays from Psyche, the GRS will also detect background gamma rays from spacecraft material nearby the GRS. Because Ni is such a key element for achieving the mission science objectives, a special effort has been made to minimize background gamma rays from Ni, thus maximizing sensitivity to the Ni gamma rays from Psyche. The Psyche mission approached this potential Ni background issue with two methods, locating the GRS away from the spacecraft/source of Ni and setting a threshold requirement against the total Ni mass of the spacecraft. Verifying that the total amount of Ni on the spacecraft is within this threshold is thus a key part of ensuring the GRS can meet its science objectives. Ni alloys are commonly used on spacecraft, but the mass and location of elemental Ni is not typically accounted for. Ni can be found in many materials all over the spacecraft – in fasteners, optical assemblies, magnetic shields, electromagnetic interference (EMI) tape, under gold plating, in connectors, and so on. The task proved further challenging because of the distributed nature of the build of this spacecraft and the use of vendors external to JPL. While the analysis was atypical and source information difficult to cull, the approach described in this paper used tools and data available to the project in some form to achieve this goal. For Psyche, current analysis shows there is margin in meeting the Ni mass requirement. This paper explains the systematic approach used to accurately and precisely record Ni content on the Psyche spacecraft. While this approach was defined for Ni on the Psyche mission, it can be used for any future project with the need to accurately estimate the total mass of a single element or material on a spacecraft.
Advanced Air Mobility (AAM) Air Mobility and Urban Air Mobility (UAM) require aircraft surveillance and monitoring for safety and security. Persistent tracking of flying objects provides Air Traffic Control (ATC) and Air Traffic Management (ATM) continuous coverage and knowledge of the national airspace (NAS). Since there are numerous more AAM and UAM aircraft than commercial aircraft, it will be challenging to utilize the same ATC/ATM architectures. A first step in creating a similar ATC/ATM architecture for AAM/UAM will require ground-based and airborne-based sensors to provide monitoring, which will be difficult in urban environments due to GPS degradation. This paper proposes a vision-based tracking method with static cameras by utilizing image subtraction and blob detection, which avoids adding additional electromagnetic interferences in the environment with sensors such as radar. The ground-based vision tracker (GBVT) outputs the detected objects' azimuth and elevation angles from unmanned aerial system (UAS) flight tests. Future and ongoing work includes sending the detected objects' azimuth and elevation angles as inputs for an extended Kalman filter (EKF) to estimate the position and velocity of the detected object.