Search NASA⌕ Search

SEARCH · Search NASA

Results for “Finite Element Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Smoothed boundary method for simulating incompressible flow in complex geometries

Simulating flow through porous media with explicit considerations of complex microstructures is very challenging using conventional sharp-interface methods because of the difficulties in generating meshes conformal to complex geometries. In this work, a diffuse interface embedded boundary method known as the Smoothed Boundary Method (SBM) is utilized to facilitate simulations of fluid dynamics involving complex geometries. In diffuse-interface methods, the geometry is described by a domain parameter. The SBM allows the straightforward reformulation of the time-dependent Navier-Stokes equations in terms of this domain parameter, using only algebraic identities. Thus, enforcing the appropriate boundary conditions at the irregular embedded boundary is greatly simplified. Adaptive mesh refinement is used to increase the accuracy of the diffuse interface method by allowing thinner interfacial thickness to be used in the domain parameter. Here, the SBM-formulated Navier-Stokes equations are solved with the Finite Difference Method on refined mesh systems. Sharp-interface Finite Element Method simulations using the commercial software COMSOL on body-conforming meshes are also provided for comparison. Favorable agreement between the two methods is observed. Since it is no longer necessary for the mesh to conform to the complex geometry, the grid system for the SBM simulations can be generated rapidly and without additional manual interventions, making the entire simulation process more expedient.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Numerical Modeling of Ocular Dysfunction in Space

Upon introduction to microgravity, the near-loss of hydrostatic pressure causes a marked cephalic (headward) shift of fluid in an astronaut's body. The fluid shift, along with other factors of spaceflight, induces a cascade of interdependent physiological responses which occur at varying time scales. Long-duration missions carry an increased risk for the development of the Visual Impairment and Intracranial Pressure (VIIP) syndrome, a spectrum of ophthalmic changes including posterior globe flattening, choroidal folds, distension of the optic nerve sheath, kinking of the optic nerve and potentially permanent degradation of visual function. In the cases of VIIP found to date, the initial onset of symptoms occurred after several weeks to several months of spaceflight, by which time the gross bodily fluid distribution is well established. We are developing a suite of numerical models to simulate the effects of fluid shift on the cardiovascular, central nervous and ocular systems. These models calculate the modified mean volumes, flow rates and pressures that are characteristic of the altered quasi-homeostatic state in microgravity, including intracranial and intraocular pressures. The results of the lumped models provide initial and boundary data to a 3D finite element biomechanics simulation of the globe, optic nerve head and retrobulbar subarachnoid space. The integrated set of models will be used to investigate the evolution of the biomechanical stress state in the ocular tissues due to long-term exposure to microgravity.

intraocular pressure↗
NASA NTRS1987

Initial dynamic load estimates during configuration design

This analysis includes the structural response to shock and vibration and evaluates the maximum deflections and material stresses and the potential for the occurrence of elastic instability, fatigue and fracture. The required computations are often performed by means of finite element analysis (FEA) computer programs in which the structure is simulated by a finite element model which may contain thousands of elements. The formulation of a finite element model can be time consuming, and substantial additional modeling effort may be necessary if the structure requires significant changes after initial analysis. Rapid methods for obtaining rough estimates of the structural response to shock and vibration are presented for the purpose of providing guidance during the initial mechanical design configuration stage.

Schiff, Daniel↗
DOE OSTI2023

Effect of sample size on the maximum value distribution of fatigue driving forces in metals and alloys

An analytical framework is presented to predict the effects of sample size on the maximum value distribution (MVD) of the driving forces for fatigue crack formation in metals and alloys. The distribution of the maximum driving force for fatigue crack formation over the domain follows the generalized extreme value theory in the limit as the domain size increases to infinity. Here, a simulation-based analysis of microstructure influences on fatigue resistance for polycrystalline metals and alloys is very costly, and reaching those limits is intractable. This work models the MVD of Fatigue Indicator Parameters (FIPs), which serve as surrogate measures for the driving force for fatigue crack formation, at finite sample sizes prior to their convergence to a limiting extreme value distribution. Large-scale crystal plasticity finite element (CPFE) simulations of FCC Al 7075-T6 with microstructure realizations of various sizes are incorporated to calibrate and evaluate the developed framework, and a total of ∼6.5 million grains of Al 7075-T6 are examined. The calibrated analytical solution agrees well with the brute force Monte Carlo simulation results extracted from the CPFE simulations. Furthermore, the developed formulation can predict the MVD of FIPs for different sample sizes using a size-dependent parameter, and it is capable of accurately extrapolating the MVD of FIPs for much larger microstructure sample sizes than the size used for its calibration.

Crystal plasticity↗
DOE OSTI2025

Quantum State Transfer between Heterogeneous 3D QPUs

We present detailed analyses and microwave simulations of a quantum interconnect architecture that couples two distinct three-dimensional quantum processing units (QPUs): (i) a two-cell superconducting radio-frequency (SRF) cavity coupled to multiple transmon qubits and (ii) a waveguide-based cavity hosting a planar circuit with transmons and resonators. The modules are linked via a low-loss superconducting coaxial cable, which serves as a quantum bus. Finite-element electromagnetic simulations are performed to optimize coupling strengths and mode frequencies for high-fidelity quantum state transfer between cavities. These simulation results provide a comprehensive blueprint for the experimental realization of a flexible quantum interconnect architecture, coupling heterogeneous QPUs.

Yaker, Joey [Fermilab]↗
NASA NTRS2000

Simulation of Aircraft Landing Gears with a Nonlinear Dynamic Finite Element Code

Recent advances in computational speed have made aircraft and spacecraft crash simulations using an explicit, nonlinear, transient-dynamic, finite element analysis code more feasible. This paper describes the development of a simple landing gear model, which accurately simulates the energy absorbed by the gear without adding substantial complexity to the model. For a crash model, the landing gear response is approximated with a spring where the force applied to the fuselage is computed in a user-written subroutine. Helicopter crash simulations using this approach are compared with previously acquired experimental data from a full-scale crash test of a composite helicopter.

Lyle, Karen H.↗
NASA NTRS2008

Efficient Modal Basis Selection Criteria for Reduced-Order Nonlinear Simulation

A modal basis selection technique for a reduced-order nonlinear numerical simulation with application to two-dimensional structures is presented as a two-step procedure. A system identification analysis is first performed using proper orthogonal decomposition. Using these results, a set of load-invariant bases consisting of the normal modes is next selected. Two criteria for making the basis selection are offered; one using the modal assurance criterion and the other using the modal expansion theorem. The quality of the subsequent reduced-order analyses are examined through comparison with computationally intensive finite element nonlinear simulations in physical degrees-of-freedom. A clamped flat isotropic plate under a random acoustic loading is considered to demonstrate the procedure. It is found that the subject procedure enables formation of an accurate and computationally efficient reduced-order system applicable to a broad range of loading conditions.

Przekop, Adam↗
DOE OSTI2020

Simulation Analysis of Geometry and Material Effects for Dropkinson Bar

The reported research is motivated by the need to address a key issue affecting the Dropkinson bar apparatus. This unresolved issue is the interference of the stress wave reflected from the bar-beam boundary with the measurement of the stress-strain response of a material tested in the apparatus. The purpose of the wave beam that is currently connected to the bar is to dissipate the stress wave, but the portion of the wave reflected from the bar-beam boundary is still significant. First, we focused on understanding which parameters affect the reflected wave's arrival time at a strain gauge. Specifically, we used finite-element numerical simulations with the Sierra/SM module to study the effects of various bar-beam connection fixities, alternative wave beam materials, and alternative geometries of the Dropkinson bar system based on a monolithic design. The conclusion of this study is that a partial reflection always occurs at the bar-beam boundary (or, for a monolithic design, at a point where the bar geometry changes). Therefore, given a fixed total length of the bar, it is impossible to increase the reflected wave's arrival time by any significant amount. After reaching this conclusion, we focused instead on trying to minimize the energy of the reflected stress wave circulating up and down through the bar over a relatively long period of time (10 ms). Once again, we used numerical simulations with the Sierra/SM module to investigate the effects of various bar-beam connection fixities, alternative wave beam materials, and parameters of an asymmetric monolithic design of the bar-and-beam system. This study demonstrated that various parameters can significantly affect the energy of the wave reflections, with the difference between best and worst configurations being about one order of magnitude in terms of energy. Based on the obtained results, we conclude with concrete takeaways for Dropkinson bar users and propose potential directions for future research and optimization.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling the 4D discharge of lithium-ion batteries with a multiscale time-dependent deep learning framework

The lithium-ion battery (LIB) field is moving towards the direction of investigating spatially resolved physical phenomena in the 3D porous microstructure of electrodes. These pore-scale simulations give new insights into the local dynamics of lithiation/de-lithiation and charge transport, Nevertheless, the computational time of these simulations limits the integration of these models in optimization workflows of cycling conditions or electrode manufacturing processes. Machine learning models present a way of assessing in real-time the performance of materials. While several successful techniques for replicating simulations with machine learning have been proposed, this case study presents a more demanding problem, due to the necessity of understanding the behavior of heterogeneous 3D local data, as it evolves in time: this poses both a scientific and a technical challenge. To this end, we propose an autoregressive multiscale convolutional neural network model to predict relevant quantities at the pore-scale in the solid phase: the lithium concentration (in the active material) and potential (in the active material and carbon binder). Here, these are ultimately used to reconstruct the battery discharge curve. 3D images of the electrode microstructures are the input to the network, trained with a dataset of finite element method simulations to predict the discharge behavior of the cathode side in lithium ion batteries. We propose this machine learning model as a proof-of-concept of the applicability of multiscale networks for time-dependent physics problems. The trained model exhibits very high accuracy (with errors lower than 2 %) in forecasting the discharge behavior of new unseen cathodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Modeling Stress-Induced Pore Water Pressures in The Vadose Zone Beneath a Composite-Lined Landfill - 20029

A finite-element model was developed to evaluate mechanisms contributing to positive pore pressures measured with sealed pressure transducers in the geological buffer beneath the Environmental Management Waste Management Facility, a composite-lined mixed waste disposal facility operated by the US Department of Energy. The geological buffer is a 3-m-thick engineered fine-textured layer directly beneath the Environmental Management Waste Management Facility's composite liner, and above the groundwater table. The model accounts for changes in pore water pressure resulting from (i) loading imposed by waste placed on the overlying liner, (ii) moistening of the geological buffer due to equilibration with the underlying geological materials, and (iii) fluctuations in the elevation of the underlying groundwater table. Pore water pressures predicted by the model are in good agreement with pore water pressures measured in the field. The predictions confirm that positive pore water pressures recorded by the sealed pressure transducers in the geological buffer are excess pore water pressures induced by the vertical normal stress imposed by waste placed on the liner, and are not due to a rise in the groundwater table. Simulations also showed that two additional years of filling would further increase the pore water pressure without any change in elevation of the groundwater table. The geological buffer remained unsaturated during the simulation, with a B-coefficient (parameter indicative of the degree of saturation) similar to that computed from the field-measured pore water pressures and waste filling records. Larger increases in pore water pressure were observed when the geological buffer was assumed to have higher initial saturation, as was observed in the field data. Incorporating seasonal fluctuations in the groundwater table beneath the geological buffer in the model resulted in predictions of small seasonal oscillation in the pore water pressure at the measurement location, similar to seasonal oscillations observed in the field. Predictions made with the model indicate that the dissipation of the excess pore water pressures will occur over decades due to the low hydraulic conductivity of the geological buffer material. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Influence of Initial fabric and water-wetting on particle fracture and force chain evolution in natural silica sand

Particle fracture has a significant influence on the engineering behavior of granular materials. However, the combined influence of the initial fabric and wetting on particle fracture and force chain evolution in granular materials, particularly in sands, remains insufficiently explored in the current literature. Here, in this paper, one-dimensional (1D) confined compression experiments were conducted on dry and wet specimens, and particle-level fracture was captured using three-dimensional (3D) in-situ Synchrotron Micro-Computed Tomography (SMT). A quantitative assessment of particle fracture revealed that wet specimens, which have disturbed fabric, exhibited a higher fracture percentage in comparison to dry specimens. Complementary 3D finite element (FE) simulations were performed using dry and wet (only solid fabric was considered and the influence of pore water is not considered) sand assemblies to assess interparticle contact forces and particle-scale stress distributions within the specimens. Force chain analysis was subsequently conducted, encompassing quantification of interparticle forces, characterization of force network structures, and monitoring the dynamic evolution of force chains under different strain levels. The results show that the specimens with disturbed fabric led to a more dynamic and less persistent force network, more fabric instability, and thus more reorganization of force chain structures. In addition, the frequent rearrangement of the force network in the presence of water (with reduced inter-particle contact friction) likely exacerbates localized stress concentrations, promoting failure in previously unengaged or weakly connected particles. The results reported in this paper offer a new insight into how the initial fabric and wetting cause different fracture behavior. The findings can also pave the way for more in-depth future investigations into the mechanics governing particle fracture in granular assemblies.

Finite element analysis↗
NASA NTRS2010

Diamond Heat-Spreader for Submillimeter-Wave Frequency Multipliers

The planar GaAs Shottky diode frequency multiplier is a critical technology for the local oscillator (LO) for submillimeter- wave heterodyne receivers due to low mass, tenability, long lifetime, and room-temperature operation. The use of a W-band (75-100 GHz) power amplifier followed by a frequency multiplier is the most common for submillimeter-wave sources. Its greatest challenge is to provide enough input power to the LO for instruments onboard future planetary missions. Recently, JPL produced 800 mW at 92.5 GHz by combining four MMICs in parallel in a balanced configuration. As more power at W-band is available to the multipliers, their power-handling capability be comes more important. High operating temperatures can lead to degradation of conversion efficiency or catastrophic failure. The goal of this innovation is to reduce the thermal resistance by attaching diamond film as a heat-spreader on the backside of multipliers to improve their power-handling capability. Polycrystalline diamond is deposited by hot-filament chemical vapor deposition (CVD). This diamond film acts as a heat-spreader to both the existing 250- and 300-GHz triplers, and has a high thermal conductivity (1,000-1,200 W/mK). It is approximately 2.5 times greater than copper (401 W/mK) and 20 times greater than GaAs (46 W/mK). It is an electrical insulator (resistivity approx. equals 10(exp 15) Ohms-cm), and has a low relative dielectric constant of 5.7. Diamond heat-spreaders reduce by at least 200 C at 250 mW of input power, compared to the tripler without diamond, according to thermal simulation. This superior thermal management provides a 100-percent increase in power-handling capability. For example, with this innovation, 40-mW output power has been achieved from a 250-GHz tripler at 350-mW input power, while the previous triplers, without diamond, suffered catastrophic failures. This breakthrough provides a stepping-stone for frequency multipliers-based LO up to 3 THz. The future work for this design is to apply the high output power from both the 250 and 300 GHz to multiple chains in order to generate milliwatts at 2.3 THz. Using the first generation of results for this innovation, 40 mW of output power were produced from a 240-GHz tripler at 350-mW input power, and 27- mW output power was produced from a 300-GHz tripler at 408-mW input power. This is two times higher than the current state-of-the-art output power capability. A finite-element thermal simulation also shows that 30-microns thick diamond dropped the temperature of the anodes by at least 200 C.

Lin, Robert H.↗
DOE OSTI2025

Large scale polymer toughening of two-dimensional materials revealed by in situ TEM fracture tests and multiscale simulations

Two-dimensional (2D) materials offer significant potential for applications in energy-harvesting devices, batteries, sensors, and transistors. However, their intrinsic brittleness makes them prone to mechanical failure, limiting their practical use. In this work, we perform in situ transmission electron microscopy (TEM) fracture tests on monolayer MoSe2 and uncover an extrinsic toughening effect induced by an ultrathin adsorbed polystyrene adlayer. This adlayer substantially enhances the fracture resistance of the 2D flakes. Through a combination of molecular dynamics simulations and finite element analysis, we elucidate the molecular mechanism behind this toughening effect. Further, it arises from the active crack-bridging behavior of entangled polymer chains and the formation of a fracture process zone that stabilizes crack propagation and increases the energy required for crack extension. The proposed toughening mechanism offers a pathway to improving the mechanical reliability of 2D material-based devices by mitigating the risk of sudden failure.

2D materials↗
DOE OSTI2026

An Anisotropic Yield and Damage Material Model to Improve the Contact Pressure Analysis in a Biomass Shredding System

Size reduction systems used in biomass processing break biomass into smaller pieces by utilizing the kinetic energy from the sharp rotating blades. Abrasive and/or erosive wear caused by biomass comminution results in blade wear of the sharp edged cutters, deteriorating the process efficiency. Here, this study aims to optimize the blade design and improve the system efficiency by attempting to understand the interactions between the blades and biomass particles. Since real-time monitoring of these interactions is impractical during operation, mechanical simulations offer a viable alternative for investigating the shredding process. Yet, the irregular geometry and complex mechanical properties of biomass—such as the anisotropic nature of woodchips and their nonlinear fracture behavior—pose significant challenges for accurately simulating contact pressure. In this work an anisotropic yield material model, along with a damage initiation and evolution function, is applied to the woodchip particle to study the contact pressure on shredder blade, offering a scientific basis for improved blade design and process efficiency. This approach can be extended to other biomass processing systems with similar anisotropic feedstocks, making it a valuable tool for advancing sustainable biomass utilization.

09 - BIOMASS FUELS↗
DOE OSTI2023

Identifying crack tip position and stress intensity factors from displacement data

Fracture prognosis and characterization efforts require knowledge of crack tip position and the Stress Intensity Factors (SIFs) acting in the vicinity of the crack. Here, in this work, we present an efficient numerical approach to infer both of these characteristics under a consistent theoretical framework from noisy, unstructured displacement data. The novel approach utilizes the separability of the asymptotic linear elastic fracture mechanics fields to expedite the search for crack tip position and is particularly useful for noisy displacement data. The manuscript begins with an assessment of the importance of accurately locating crack tip position when quantifying the SIFs from displacement data. Next, the proposed separability approach for quickly inferring crack tip position is introduced. Comparing to the widely used displacement correlation approach, the performance of the separability approach is assessed. Cases involving both noisy data and systematic deviation from the asymptotic linear elastic fracture mechanics model are considered, e.g. inelastic material behavior and finite geometries. An open source python implementation of the proposed approach is available for use by those doing field and laboratory work involving digital image correlation and simulations, e.g. finite element, discrete element, molecular dynamics and peridynamics, where the crack tip position is not explicitly defined.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Characterization of Fe-6Si Soft Magnetic Alloy Produced by Laser-Directed Energy Deposition Additive Manufacturing

Abstract Commercial electrical steels, Fe-Si alloys with < 4 wt.% Si, are inexpensive and efficient materials for electrical power conversion. Further efficiency improvements require increasing the silicon concentration to 6 wt.%, at which point the material becomes brittle and difficult to form by conventional rolling and sheet fabrication methods. Additive manufacturing stands to overcome challenges with commercial manufacturing techniques by leveraging near-net-shape fabrication. The wide array of process conditions provides additive manufacturing with increased flexibility, enabling control over the microstructure and mechanical properties. This work explores the microstructures and magnetic properties of ring-shaped Fe-Si alloys produced using concentric and cross-hatch tool paths on a laser-directed energy deposition additive manufacturing system. Concentric-built samples exhibit elongated grain structures while cross-hatch-built samples comprise lower aspect ratio grain structures. Thermal finite element analysis simulations model the stress conditions produced by the different scan path geometries. Microhardness measurements probe the mechanical properties as a function of anneal temperature, providing a qualitative understanding of the intergranular defect density. Soft magnetic properties measured under quasistatic and AC conditions show frequency- and microstructure-dependent coercivity and permeability. Finally, analysis of the core loss quantifies how the build strategies and thermal treatments influence efficiency in electrical power conversion applications. Understanding the influences of scan path geometry and thermal treatment provides a pathway towards application of additively manufactured soft magnetic materials.

Adamczyk, Jesse M.↗
DOE OSTI2023

Contact pressure analysis to allow improved design for the clearing plate in a biomass comminution system

For biomass processing systems, feedstocks with small but equal sizes can improve flowability and thermochemical outputs. The Crumbler rotary shear system was designed to achieve such ideal feedstocks to reduce costs and energy throughout the biomass supply chain. Improving the wear resistance of major components in this system is important to decrease the cost. Accelerating the feedstock flow through the rotary shear machine plays an equivalent role of improving its efficiency. An analytical analysis and a finite-element analysis of the stationary clearing plate are presented in this work. Here, these tools are used to investigate the effect of contact surface curvature on the impact pressure. The optimized new clearing plate design is expected to improve the component’s lifetime and wood chips flowability. The field tests confirm that the trend of the new clearing plate design guided by FEA. The optimization method, model verification, and validation experience applied in this work can also be applied to other static components with similar simple contact wear problems.

09 BIOMASS FUELS↗
DOE OSTI2021

Statistical analysis of spatial distribution of pores in metal additive manufacturing

We report mechanical properties of additively manufactured parts are sensitive to the presence of pores form during the manufacturing process. The impact of pores on the mechanical performance has been investigated extensively with respect to different parameters, such as pore volume fraction, shape, and size. However, statistical investigations focusing on the relationships between the spatial distribution of pores and process parameters; and consequently, the performance of the manufactured parts are scattered and limited. Also, these sparse investigations usually suffer from an ambiguous definition of terminologies. For instance, the required criteria to consider a point pattern as complete spatial randomness (CSR) are generally not clarified. Moreover, no numerical formalism is yet developed to show how much the observed spatial results are statistically significant. To address these shortcomings, the statistical definition of CSR in a point pattern and the procedure to quantitatively determine the deviation of a pattern from CSR were discussed. The explained statistical approach was used to investigate the effect of scanning speed parameter on the spatial distribution of gas pores in laser powder bed fusion manufactured stainless steel parts. Furthermore, and to highlight the impact of the spatial distribution of pores on mechanical properties, fatigue performances of parts with clustered and randomly distributed pores were simulated by finite element analysis. It is shown that by reducing the scanning speed, the spatial distribution of gas pores deviated more from CSR, and correspondingly fatigue performance deteriorated.

36 MATERIALS SCIENCE↗