Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fire Response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

In-Space Loads Analysis of SLS/Orion

The Space Launch System and Orion spacecraft experience unique load cases during upper stage flight since the Orion must deploy its solar arrays before the upper stage engine fires. The low frequency bending modes of the deployed arrays have the potential to interact with the slosh modes of the upper stage, and with the upper stage flight steady-state accelerations this can induce high loads in the array mechanisms. A time-domain transient response solution is used to evaluate the array mechanism loads, sensitivities are noted, and the final loads are determined to be within the capability of the mechanism. Section loads and accelerations are also recovered and assessed.

SLS↗
NASA NTRS2009

Implications of Dynamic Pressure Transducer Mounting Variations on Measurements in Pyrotechnic Test Apparatus

Accurate dynamic pressure measurements are often difficult to make within small pyrotechnic devices, and transducer mounting difficulties can cause data anomalies that lead to erroneous conclusions. Delayed initial pressure response followed by data ringing has been observed when using miniaturized pressure transducer mounting adapters required to interface transducers to small test chambers. This delayed pressure response and ringing, combined with a high data acquisition rate, has complicated data analysis. This paper compares the output signal characteristics from different pressure transducer mounting options, where the passage distance from the transducer face to the pyrotechnic chamber is varied in length and diameter. By analyzing the data and understating the associated system dynamics, a more realistic understanding of the actual dynamic pressure variations is achieved. Three pressure transducer mounting configurations (elongated, standard, and face/flush mount) were simultaneously tested using NASA standard initiators in closed volume pressure bombs. This paper also presents results of these pressure transducer mounting configurations as a result of a larger NASA Engineering and Safety Center pyrovalve test project. Results from these tests indicate the improved performance of using face/flush mounted pressure transducers in this application. This type of mounting improved initial pressure measurement response time by approximately 19 s over standard adapter mounting, eliminating most of the lag time; provided a near step-function type initial pressure increase; and greatly reduced data ringing in high data acquisition rate systems. The paper goes on to discuss other issues associated with the firing and instrumentation that are important for the tester to understand.

Dibbern, Andreas↗
NASA NTRSDate not supplied

In-Space Loads Analysis of SLS/Orion

The Space Launch System and Orion spacecraft experience unique load cases during upper stage flight since the Orion must deploy its solar arrays before the upper stage engine fires. The low frequency bending modes of the deployed arrays have the potential to interact with the slosh modes of the upper stage. In combination with the upper stage flight steady-state accelerations this can induce high loads in the array mechanisms. A time-domain transient response solution is used to evaluate the array mechanism loads, sensitivities are noted, and the final loads are determined to be within the capability of the mechanism. Section loads and accelerations are also recovered and assessed.

SLS↗
NASA NTRS1975

Detection of the isotopes of heavy cosmic ray nuclei

A counter telescope designed to detect and resolve the isotopic composition of cosmic ray nuclei heavier than neon is being prepared. The telescope consists of a rather conventional charge measuring array using two scintillator elements and two solid Cerenkov radiators of differing refractive index. The mass measurement is obtained by combining the velocity information from one or both of the Cerenkov radiators operating near their threshold with residual range measured in a block of nuclear emulsion. Path length corrections and particle location in the emulsions is provided by a spark chamber fired in coincidence with potentially suitable particles. The telescope has a geometry factor of 530 sq cm sr roughly. It should be able to resolve the isotopes of iron over the energy range of 300 to 720 Mev/n and those of neon over 300 to 400 MeV/n. The expected response and characteristics of the telescope are described in detail and the sensitivity to rare isotopes discussed.

Gilman, C. M.↗
NASA NTRS1993

An Experimental and Theoretical Study of Radiative Extinction of Diffusion Flames

In a recent paper on 'Observations of candle flames under various atmospheres in microgravity' by Ross et al., it was found that for the same atmosphere, the burning rate per unit wick surface area and the flame temperature were considerably reduced in microgravity as compared with normal gravity. Also, the flame (spherical in microgravity) was much thicker and further removed from the wick. It thus appears that the flame becomes 'weaker' in microgravity due to the absence of buoyancy generated flow which serves to transport the oxidizer to the combustion zone and remove the hot combustion products from it. The buoyant flow, which may be characterized by the strain rate, assists the diffusion process to execute these essential functions for the survival of the flame. Thus, the diffusion flame is 'weak' at very low strain rates and as the strain rate increases the flame is initially 'strengthened' and eventually it may be 'blown out'. The computed flammability boundaries of T'ien show that such a reversal in material flammability occurs at strain rates around 5 sec. At very low or zero strain rates, flame radiation is expected to considerably affect this 'weak' diffusion flame because: (1) the concentration of combustion products which participate in gas radiation is high in the flame zone; and (2) low strain rates provide sufficient residence time for substantial amounts of soot to form which is usually responsible for a major portion of the radiative heat loss. We anticipate that flame radiation will eventually extinguish this flame. Thus, the objective of this project is to perform an experimental and theoretical investigation of radiation-induced extinction of diffusion flames under microgravity conditions. This is important for spacecraft fire safety.

Atreya, Arvind↗
NASA NTRS2013

KINEROS2-AGWA: Model Use, Calibration, and Validation

KINEROS (KINematic runoff and EROSion) originated in the 1960s as a distributed event-based model that conceptualizes a watershed as a cascade of overland flow model elements that flow into trapezoidal channel model elements. KINEROS was one of the first widely available watershed models that interactively coupled a finite difference approximation of the kinematic overland flow equations to a physically based infiltration model. Development and improvement of KINEROS continued from the 1960s on a variety of projects for a range of purposes, which has resulted in a suite of KINEROS-based modeling tools. This article focuses on KINEROS2 (K2), a spatially distributed, event-based watershed rainfall-runoff and erosion model, and the companion ArcGIS-based Automated Geospatial Watershed Assessment (AGWA) tool. AGWA automates the time-consuming tasks of watershed delineation into distributed model elements and initial parameterization of these elements using commonly available, national GIS data layers. A variety of approaches have been used to calibrate and validate K2 successfully across a relatively broad range of applications (e.g., urbanization, pre- and post-fire, hillslope erosion, erosion from roads, runoff and recharge, and manure transport). The case studies presented in this article (1) compare lumped to stepwise calibration and validation of runoff and sediment at plot, hillslope, and small watershed scales; and (2) demonstrate an uncalibrated application to address relative change in watershed response to wildfire.

Erosion↗
NASA NTRS2016

Cross Correlation versus Normalized Mutual Information on Image Registration

This is the first study to quantitatively assess and compare cross correlation and normalized mutual information methods used to register images in subpixel scale. The study shows that the normalized mutual information method is less sensitive to unaligned edges due to the spectral response differences than is cross correlation. This characteristic makes the normalized image resolution a better candidate for band to band registration. Improved band-to-band registration in the data from satellite-borne instruments will result in improved retrievals of key science measurements such as cloud properties, vegetation, snow and fire.

band-to-band↗
NASA NTRS1994

Microphysical modeling of cirrus. 1: Comparison with 1986 FIRE IFO measurements

We have used a one-dimensional model of cirrus formation to study the development of cirrus clouds during the 1986 First ISCCP (International Satellite Cloud Climatology Project) Regional Experiment (FIRE) intensive field observations (IFO). The cirrus model includes microphysical, dynamical, and radiative processes. Sulfate aerosols, solution drops, ice crystals, and water vapor are all treated as interactive elements in the model. Ice crystal size distributions are fully resolved based on calculations of homogeneous freezing nucleation, growth by water vapor deposition, evaporation, coagulation, and vertical transport. We have focused on the cirrus observed on November 1, 1986. Vertical wind speed for the one-dimensional simulation is taken from a mesoscale model simulation for the appropriate time period. The mesoscale model simulation suggested that strong upward motions over Wyoming and subsequent horizontal transport of upper level moisture were responsible for the cirrus observed over Wisconsin on this date. We assumed that our one-dimensional model could be used to represent a vertical column moving from Wyoming to Wisconsin over a period of several hours. Ice crystal nucleation occurs in our model in the 8 to 10-km region as a result of the strong updrafts (and cooling) early in the simulation. Growth, coagulation, and sedimentation of these ice crystals result in a broad cloud region (5-10 km thick) with an optical depth of 1-2 after a few hours, in agreement with the FIRE measurements. Comparison with aircraft microphysical measurements made over Wisconsin indicates that the simulation generated reasonable ice water content, but the predicted ice number densities are too low, especially for radii less than about 50 microns. Sensitivity tests suggest that better agreement between simulated and observed microphysical properties is achieved if the nucleation rate is higher or stronger vertical mixing (perhaps associated with multidimensional motions) is present.

Jensen, Eric J.↗
NASA NTRSDate not supplied

UAM Decision Making

NASA, in collaboration with the industry and FAA, is conducting research on Urban Air Mobility (UAM). UAM introduces unique and evolving operational characteristics unaccounted for within current transportation planning tools. This evolving modality requires a unique and comprehensive tool that integrates new and existing planning methodologies to provide a holistic solution for decision makers. NASA has identified a number of barriers and research areas related to aircraft, airspace, and communities as well as infrastructure requirements. The research will identify requirements related to urban capable aircraft and airspace technologies. While civil aviation authorities are responsible for safety and structure of operations through the air, the local and regional authorities are responsible for decisions related to location of vertiports, helipads, and airports. The implementation of UAM vertiports will consider diverse regional system categories such as weather, airspace restrictions, noise acceptability, surface traffic, availability of power, vertipad locations, routes, impact on surface traffic, safety and risks, economic impact, ingress/egress for electric/hybrid VTOL aircraft, applicable fire codes, evacuation strategy, zoning requirements, emergency preparedness, interactions with surface traffic, and community acceptance. Therefore, regional implementation bodies need a decision making tool to assess systemic dependencies in preparation for UAM impact on the region. We are developing a simulation and modeling tool that allows regional authorities to consider many factors while deciding the location of vertiport and UAM operations. The objective of this paper is to present the conceptual design of a comprehensive decision making tool to assist planning bodies in developing UAM infrastructure. Specifically, the UAM planning tool will simultaneously consider all relevant local/regional considerations to identify for vertiport locations and UAM operations for a region.

Parimal Kopardekar↗
NASA NTRS1972

Space simulation experiments on reaction control system thruster plumes.

A space simulation procedure was developed for studying rocket plume contamination effects using a 5-lb bipropellant reaction control system thrustor. Vacuum chamber pressures of 0.00003 torr (70 miles altitude) were achieved with the thrustor firing in pulse trains consisting of eight pulses - 50 msec on, 100 msec off, and seven minutes between pulse trains. The final vacuum was achieved by cooling all vacuum chamber surfaces to liquid-helium temperature and by introducing a continuous argon leak of 48 std. cc/sec into the test chamber. Fast time response liquid flow rate measurements showed that large variations occurred in the ratio of oxidizer to fuel flow for pulse-on times up to 120 msec. These variations could lead to poor combustion efficiency and the production of contamination.

Cassidy, J. F.↗
NASA NTRS1989

Historical perspective - Viking Mars Lander propulsion

This paper discusses the Viking 1 and 2 missions to Mars in 1975-1976 and describes the design evolution of the Viking Terminal Descent Rocket Engines responsible for decelerating the Viking Mars Landers during the final portion of their descent from orbit. The Viking Terminal Descent Rocket Engines have twice the thrust of the largest monopropellant hydrazine engine developed previously but weigh considerably less. The engine has 18 nozzles, the capability of 10:1 throttling, is totally sealed until fired, employs no organic unsealed materials, is 100 percent germ free, utilized hydrazine STM-20 as the propellant, and starts at a temperature more than 45 F below the propellant's freezing point.

Morrisey, Donald C.↗
NASA NTRS1974

Some injector element detail effects on screech in hydrogen-oxygen rockets

An experimental investigation was conducted to learn more about how the specific details of a concentric tube injection element affect the screech characteristics of a hydrogen-oxygen rocket engine. The four variables investigated were (1) impingement angle, (2) oxidizer tube blunt base thickness, (3) oxidizer tube recess and extension, and (4) oxidizer tube-annulus concentricity. Tests were made using a 27.34-cm (10.77-in.) diameter heat sink combustor at nominally 300-psia chamber pressure. All of the test variables were investigated using a 157 element circular pattern injector. Additional oxidizer tube recess tests were made with a 421 element hexagonal pattern injector. Tests were conducted over the oxidant-fuel ratio range of 4 to 6. Stability evaluation for each configuration was made using the hydrogen temperature rating technique. Several element configurations were also cold flow tested using nitrogen and water as simulants. The element detail changes resulted in changes in hydrogen injector pressure drop even though the physical injection area was constant for all similar tests in both hot firing and cold flow tests. These changes in injector pressure drop produced changes in combustion stability. The data were correlated with a modified version of a previously reported injection area ratio correlation. By interpreting changes in injector pressure drop as changes in injector hydrogen flow resistance, the data were compared with a hydrogen flow response stability model and were found to be in agreement.

Hannum, N. P.↗
NASA NTRS1991

German telecommunications satellite (Deutscher fernmelde satellit) (DFS-1 and -2)

The German Telecommunications Satellite (DFS) Program is to provide telecommunications service for high data rate transmission of text and video data to the Federal Republic of Germany within the 11-14 GHz and 20-30 GHz bands. The space segment of this program is composed of three satellites, DFS-1, DFS-2, and DFS-3, which will be located at 23.5 degrees E longitude of the geostationary orbit. The DFS will be launched from the Center Spatial Guyanis in French Giana on an Ariane launch vehicle. The mission follows the typical injection sequence: parking orbit, transfer orbit, and earth orbit. Attitude maneuvers will be performed to orient the spacecraft prior to Apogee Kick Motor (AKM) firing. After AKM firing, drift phase orbital and attitude maneuvers will be performed to place the spacecraft in its final geostationary position. The Deep Space Network (DSN) will support the transfer and drift orbit mission phases. Information is presented in tabular form for the following areas: DSN support, compatibility testing, frequency assignments, telemetry, command, and tracking support responsibilities.

Hiendlmeier, G.↗
NASA NTRS1995

Geostationary Operational Environmental Satellite (GOES)-8 mission flight experience

The Geostationary Operational Environmental Satellite (GOES)-8 spacecraft was launched on April 13, 1994, at 06:04:02 coordinated universal time (UTC), with separation from the Atlas-Centaur launch vehicle occurring at 06:33:05 UTC. The launch was followed by a series of complex, intense operations to maneuver the spacecraft into its geosynchronous mission orbit. The Flight Dynamics Facility (FDF) of the Goddard Space Flight Center (GSFC) Flight Dynamics Division (FDD) was responsible for GOES-8 attitude, orbit maneuver, orbit determination, and station acquisition support during the ascent phase. This paper summarizes the efforts of the FDF support teams and highlights some of the unique challenges the launch team faced during critical GOES-8 mission support. FDF operations experience discussed includes: (1) The abort of apogee maneuver firing-1 (AMF-1), cancellation of AMF-3, and the subsequent replans of the maneuver profile; (2) The unexpectedly large temperature dependence of the digital integrating rate assembly (DIRA) and its effect on GOES-8 attitude targeting in support of perigee raising maneuvers; (3) The significant effect of attitude control thrusting on GOES-8 orbit determination solutions; (4) Adjustment of the trim tab to minimize torque due to solar radiation pressure; and (5) Postlaunch analysis performed to estimate the GOES-8 separation attitude. The paper also discusses some key FDF GOES-8 lessons learned to be considered for the GOES-J launch which is currently scheduled for May 19, 1995.

Noonan, C. H.↗
NASA NTRS2021

The Impacts of Climate and Wildfire on Ecosystem Gross Primary Productivity in Alaska

The increase in wildfire occurrence and severity seen over the past decades in the boreal and Arctic biomes is expected to continue in the future in response to rapid climate change in this region. Recent studies documented positive trends in gross primary productivity (GPP) for Arctic boreal biomes driven by warming, but it is unclear how GPP trends are affected by wildfires. Here, we used satellite vegetation observations and environmental data with a diagnostic GPP model to analyze recovery from large fires in Alaska over the period 2000‐2019. We confirmed earlier findings that warmer‐than‐average years provide favorable climate conditions for vegetation growth, leading to a GPP increase of 1 Tg C/yr, contributed mainly from enhanced productivity in the early growing season. However, higher temperatures increase the risk of wildfire occurrence leading to direct carbon loss over a period of 1‐3 years. While mortality related to severe wildfires reduce ecosystem productivity, post‐fire productivity in moderately burned areas shows a significant positive trend. The rapid GPP recovery following fires reported here might be favorable for maintaining the region’s net carbon sink, but wildfires can indirectly promote the release of long‐term stored carbon in the permafrost. With the projected increase in severity and frequency of wildfires in the future, we expect a reduction of GPP and therefore amplification of climate warming in this region.

Nima Madani↗
NASA NTRS2022

UAV Path Planning for Wildfires - Sustainably Fighting Wildfires with Automated Path Planning for UAVs

As the severity and frequency of wildfires increase, infrastructure, properties, national parks, animal habitats, and human lives (civilians and firefighters) are put at greater risk. This paper examines the possible application of algorithmic path planning for UAV reconnaissance to reduce damage and safety risks, as aforementioned. When the location of a wildfire is known, UAVs are immediately dispatched from an operating base to fly to the fire and support the firefighters as quickly as possible. Then, the algorithm incrementally analyzes different environmental factors to create a path for the UAV to follow. This work focuses on generating a path for the UAV to follow given a set of polygons representing obstacles. The most important features of this algorithm are its fast response time and obstacle maneuverability. The use of an efficient path planning algorithm could potentially save lives, infrastructure, and acres of forest destruction.

UAV↗
NASA NTRS1986

Safety considerations of lithium-thionyl chloride cells

The use of spirally wound lithium-thionyl chloride (Li-SOCl2) cells is currently limited because of their hazardous behavior. Safety hazards have ranged from mild venting of toxic materials to violent explosions and fires. These incidents may be related to both user- and manufacturer-induced causes. Many explanations have been offered to explain the unsafe behavior of the cells under operating and abuse conditions. Explanations fall into two categories: (1) thermal mechanisms, and (2) chemical mechanisms. However, it is quite difficult to separate the two. Both may be responsible for cell venting or explosion. Some safety problems encountered with these cells also may be due to design deficiencies and ineffective quality control during cell fabrication. A well-coordinated basic and applied research program is needed to develop safe Li-SOCl2 cells. Recommendations include: (1) learnig more about Li-SOL2 cell chemistry; (2) modeling cell and battery behavior; (3) optimizing cell design for safety and performance, (4) implementing quality control procedures; and (5) educating users.

Subbarao, Surampudi↗
NASA NTRS2021

Air Pollution Scenario over Pakistan: Characterization and Ranking of Extremely Polluted Cities using Long-Term Concentrations of Aerosols and Trace Gases

Pakistan ranks third in the world in terms of mortality attributable to air pollution, with aerosol mass concentrations (PM2.5) consistently well above WHO (World Health Organization) air quality guidelines (AQG). However, regulation is dependent on a sparse network of air quality monitoring stations and insufficient ground data. This study utilizes long-term observations of aerosols and trace gases to characterize and rank the air pollution scenarios and pollution characteristics of 80 selected cities in Pakistan. Datasets used include (1) the Aqua and Terra (AquaTerra) MODIS (Moderate Resolution Imaging Spectroradiometer) Level 2 Collection 6.1 merged Dark Target and Deep Blue (DTB) aerosol optical depth (AOD) retrieval products; (2) the CAMS (Copernicus Atmosphere Monitoring Service) reanalysis PM1, PM2.5, and PM10 data; (3) the MERRA-2 (Modern-Era Retrospective analysis for Research and Applications, Version 2) reanalysis PM2.5 data, (4) the OMI (Ozone Monitoring Instrument) tropospheric vertical column density (TVCD) of nitrogen dioxide (NO2), and VCD of sulfur dioxide (SO2) in the Planetary Boundary Layer (PBL), (5) the VIIRS (Visible Infrared Imaging Radiometer Suite) Nighttime Lights data, (6) MODIS Collection 6 Version 2 global monthly fire location data (MCD14ML), (7) population density, (8) MODIS Level 3 Collection 6 land cover types, (9) AERONET (AErosol RObotic NETwork) Version 3 Level 2.0 data, and (10) ground-based PM2.5 concentrations from air quality monitoring stations. Potential Source Contribution Function (PSCF) analyses were performed by integrating with ground-based PM2.5 concentrations and the NOAA (National Oceanic and Atmospheric Administration) HYSPLIT (Hybrid Single-Particle Lagrangian Integrated Trajectory) air parcel back trajectories to identify potential pollution source areas which are responsible for extreme air pollution in Pakistan. Results show that the ranking of the top polluted cities depends on the type of pollutant considered and the metric used. For example, Jhang, Multan, and Vehari were characterized as the top three polluted cities in Pakistan when considering AquaTerra DTB AOD products; for PM1, PM2.5, and PM10 Lahore, Gujranwala, and Okara were the top three; for tropospheric NO2 VCD Lahore, Rawalpindi, and Islamabad and for PBL SO2 VCD Lahore, Mirpur, and Gujranwala. The results demonstrate that Pakistan’s entire population has been exposed to high PM2.5 concentrations for many years, with a mean annual value of 54.7 μg/cu. m, over all Pakistan from 2003 to 2020. This value exceeds Pakistan’s National Environmental Quality Standards (Pak-NEQS, i.e., <15 μg/cu. m annual mean) for ambient air defined by the Pakistan Environmental Protection Agency (Pak-EPA) as well as the WHO Interim Target-1 (i.e., mean annual PM2.5 <35 μg/cu. m). The spatial analyses of the concentrations of aerosols and trace gases in terms of population density, nighttime lights, land cover types, and fire location data, and the PSCF analysis indicate that Pakistan’s air quality is strongly affected by anthropogenic sources inside of Pakistan, with contributions from surrounding countries. Statistically significant positive (increasing) trends in PM1, PM2.5, PM10, tropospheric NO2 VCD, and SO2 VCD were observed in ~89%, ~67%, ~48%, 91%, and ~88% of the Pakistani cities (80 cities), respectively. This comprehensive analysis of aerosol and trace gas levels, their characteristics in spatio-temporal domains, and their trends over Pakistan, is the first of its kind. Results will be helpful to the Ministry of Climate Change (Government of Pakistan), Pak-EPA, SUPARCO (Pakistan Space and Upper Atmosphere Research Commission), policymakers, and the local research community to mitigate air pollution and its effects on human health.

Muhammad Bilal↗