SEARCH · Search NASA

Results for “Free surface velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Apollo/Saturn 5 Postflight Trajectory - SA-513 Skylab 1 Mission. Tracking and Flight Reconstruction

The postflight trajectory for the Apollo/Saturn V SA-513 Skylab I flight is presented. An analysis is included of the orbital and powered flight trajectories of the launch vehicle, the orbital trajectory of the spent S-II stage, and the free flight impact trajectory of the expended S-IC stage. Launch vehicle trajectory dependent parameters are provided in earth-fixed launch site, launch vehicle navigation, and geographic polar coordinate systems. The time history of the trajectory parameters for the launch vehicle is presented from guidance reference release to the transfer to ATM control. Tables of significant launch vehicle parameters at engine cutoff, stage separation, and workshop orbit insertion are included. Figures of such parameters as altitude, surface and cross range, and the magnitude of total velocity and acceleration as a function of range time for the powered flight trajectory are given.

Source record↗

NASA NTRS1991

Investigation of nose bluntness and angle of attack effects on slender bodies in viscous hypersonic flows

Hypersonic flows over cones and straight biconic configurations are calculated for a wide range of free stream conditions in which the gas behind the shock is treated as perfect. Effect of angle of attack and nose bluntness on these slender cones in air is studied extensively. The numerical procedures are based on the solution of complete Navier-Stokes equations at the nose section and parabolized Navier-Stokes equations further downstream. The flow field variables and surface quantities show significant differences when the angle of attack and nose bluntness are varied. The complete flow field is thoroughly analyzed with respect to velocity, temperature, pressure, and entropy profiles. The post shock flow field is studied in detail from the contour plots of Mach number, density, pressure, and temperature. The effect of nose bluntness for slender cones persists as far as 200 nose radii downstream.

Sehgal, A. K.↗

NASA NTRS1992

Combined effect of nose bluntness and angle of attack on slender bodies in viscous hypersonic flows

Tiwari, S. N.↗

NASA NTRS1992

Studies of a flat wake rotor theory

A computer code was developed at Princeton University to calculate the velocity components in the flow field near a lifting rotor. The induced velocity components in the rotor flow field predicted by this theory are compared with experiment. It appears that on balance, this relatively simple theory gives a reasonable prediction of the average induced velocities in a rotor flow and is quite suitable for such applications as estimating the influence of the rotor wake on the tail surfaces of rotorcraft. The theory predicts that significant induced velocity components are present in all three flow directions in the wake at a lifting rotor. It should be noted , however, that there are a few experimental measurements of the longitudinal and lateral induced velocity components in the rotor wake. This theory, known as the flat wake theory, is essentially the rotary wing analog of Prandtl's lifting line theory. The theory is described in this report. Calculations based on the theory are presented and compared with a modern free wake theory.

Curtiss, H. C., Jr.↗

NASA NTRS1992

Hot streaks and phantom cooling in a turbine rotor passage. II - Combined effects and analytical modelling

Experimental documentation and analytical correlations demonstrating the effects of hot streak accumulation and phantom cooling on turbine rotor airfoil surface temperature are presented. Results are shown which quantify the impact of a nonuniform temperature profile at the entrance of a turbine due to combustor-generated hot and cold streaks, and cooling air discharged from the trailing edge of the upstream stator. Experimental results are shown for a range of controlling variables to identify where streak accumulation and phantom cooling were most likely to be strongest. These variables include streak-to-free stream density ratio, streak injection location, and coolant-to-free stream density and velocity ratios. Experimental results are shown for the combined effects of hot streak and stator coolant on the adiabatic recovery temperature of the rotor.

Roback, Richard J.↗

NASA NTRS2001

Structural and Acoustic Numerical Modeling of a Curved Composite Honeycomb Panel

The finite and boundary element modeling of the curved section of a composite honeycomb aircraft fuselage sidewall was validated for both structural response and acoustic radiation. The curved panel was modeled in the pre-processor MSC/PATRAN. Geometry models of the curved panel were constructed based on the physical dimensions of the test article. Material properties were obtained from the panel manufacturer. Finite element models were developed to predict the modal parameters for free and supported panel boundary conditions up to a frequency of 600 Hz. Free boundary conditions were simulated by providing soft foam support under the four comers of the panel or by suspending the panel from elastic bands. Supported boundary conditions were obtained by clamping the panel between plastic tubing seated in grooves along the perimeter of a stiff and heavy frame. The frame was installed in the transmission loss window of the Structural Acoustic Loads and Transmission (SALT) facility at NASA Langley Research Center. The structural response of the curved panel due to point force excitation was predicted using MSC/NASTRAN and the radiated sound was computed with COMET/Acoustics. The predictions were compared with the results from experimental modal surveys and forced response tests on the fuselage panel. The finite element models were refined and updated to provide optimum comparison with the measured modal data. Excellent agreement was obtained between the numerical and experimental modal data for the free as well as for the supported boundary conditions. Frequency response functions (FRF) were computed relating the input force excitation at one panel location to the surface acceleration response at five panel locations. Frequency response functions were measured at the same locations on the test specimen and were compared with the calculated FRF values. Good agreement was obtained for the real and imaginary parts of the transfer functions when modal participation was allowed up to 3000 Hz. The validated finite element model was used to predict the surface velocities due to the point force excitation. Good agreement was obtained between the spatial characteristics of the predicted and measured surface velocities. The measured velocity data were input into the acoustic boundary element code to compute the sound radiated by the panel. The predicted sound pressure levels in the far-field of the panel agreed well with the sound pressure levels measured at the same location.

Grosveld, Ferdinand W.↗

NASA NTRS1973

Apollo/Saturn 5 postflight trajectory: AS-512

The postflight trajectory is presented for the Apollo/Saturn V AS-512 flight. An analysis is included of the orbital and powered flight trajectories of the launch vehicle and the free flight trajectories of the expended S-IC and S-II stages. Trajectory dependent parameters are provided in earth-fixed launch site, launch vehicle navigation, and geographic polar coordinate systems. The time history of the trajectory parameters for the launch vehicle is presented from guidance reference release to Command Service Module (CSM) separation. Tables of significant parameters at engine cutoff, stage separation, parking orbit insertion, and translunar injection are included. Figures of such parameters as altitude, surface and cross range, and the magnitude of total velocity and acceleration as a function of range time for the powered flight trajectories are presented.

Pinson, G. T.↗

NASA NTRS1991

Reattachment studies of an oscillating airfoil dynamic stall flow field

The reattaching flow over an oscillating airfoil executing large amplitude sinusoidal motion around a mean angle of attack of 10 degrees has been studied using the techniques of stroboscopic schlieren, two component laser Doppler velocimetry and point diffraction interferometry, for a free stream Mach number of 0.3 and a reduced frequency of 0.05. The results show that the dynamically stalled flow reattaches in a process that begins when the airfoil is very close to the static stall angle on its downward stroke and progresses over the airfoil through a large range of angles of attack as the airfoil decreases to about 6 degrees. The airfoil suction peak shows a dramatic rise as the static stall angle is approached and the velocity profiles develop such that the flow near the surface is accelerated. The process completes through the disappearance of a separation bubble that forms over the airfoil.

Ahmed, S.↗

NASA NTRS1975

A generalized hyperbolic marching technique for three-dimensional supersonic flow with shocks

The current paper introduces a generalized, nonorthogonal coordinate system for application to supersonic flows with such large angles between streamlines of the initial Cauchy data and the marching direction that the velocity component in the marching direction is actually subsonic. Finite-difference operators are developed to solve the three-dimensional, steady, inviscid conservation equations of fluid flow referenced to this general frame. Moreover, a new method of aligning the difference mesh to the bow shock wave is presented which eliminates both the necessity for differencing the free-stream flow properties and the spurious fluctuations that often arise in conservative variables when they are differenced across the discontinuity. Results are given for the case of flow past a conical surface.

Rizzi, A. W.↗

NASA NTRS1983

Application of laser anemometry to cryogenic wind tunnels

The installation and tests conducted with the laser Doppler and transit anemometer in the 0.3-Meter Transonic Cryogenic Tunnel are described. Using residual particulates in the flow field, a series of free stream velocity measurements were conducted which agreed to within 1-percent of predicted values for a range of Mach numbers, 0.2 to 0.85, and temperatures, 100 to 250 K. Measurements about a shock wave provided an estimate of scattering particulate size of 4 microns or less. The particle concentration is approximately 3 x 10 to the 5th to 1.6 x 10 to the 6th/cu m. Necessary isolation of the plenum wall windows from ambient air with slightly positive pressure of dry nitrogen gas to prevent condensation on the window surface was achieved. This was accomplished through the use of large enclosures fixed to the tunnel wall. A second method used an additional sheet of thin plate glass to create the dry gas pocket next to the plenum window. The installation of a laser anemometer in the National Transonic Facility is examined. The laser transit anemometer has been tentatively selected for the initial entry because of its compact laser-optics package.

Hunter, W. W., Jr.↗

NASA NTRS1976

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces - A velocity-rate-controlled, pressure-bias-modulated system

During maximum braking the average ratio of drag-force friction coefficient developed by the antiskid system to maximum drag-force friction coefficient available at the tire/runway interface was higher on dry surfaces than on wet surfaces. The gross stopping power generated by the brake system on the dry surface was more than twice that obtained on the wet surfaces. With maximum braking applied, the average ratio of side-force friction coefficient developed by the tire under antiskid control to maximum side-force friction available at the tire/runway interface of a free-rolling yawed tire was shown to decrease with increasing yaw angle. Braking reduced the side-force friction coefficient on a dry surface by 75 percent as the wheel slip ratio was increased to 0.3; on a flooded surface the coefficient dropped to near zero for the same slip ratio. Locked wheel skids were observed when the tire encountered a runway surface transition from dry to flooded, due in part to the response time required for the system to sense abrupt changes in the runway friction; however, the antiskid system quickly responded by reducing brake pressure and cycling normally during the remainder of the run on the flooded surface.

Stubbs, S. M.↗

NASA NTRS2020

Crater Morphometry and Scaling in Coarse, Rubble-Like Targets: Insights from Impact Experiments

Spacecraft images reveal that the asteroids Itokawa, Ryugu, and Bennu are covered with coarse, boulder-rich material [1–3]. Impactors that collide with these bodies encounter a target with extreme physical heterogeneity. Other bodies can also possess significant physical heterogeneity (e.g., megaregolith, layering, etc.). Such heterogeneities establish free surfaces and impedance contrasts that can affect shock propagation and attenuation. Therefore, such heterogeneities may also affect crater formation and excavation [4], melt generation [5–7] and crater scaling [4]. As described by [8,9], the extent to which target heterogeneity affects crater formation likely depends on how the length scale, d, of the heterogeneity (e.g., boulder size on a rubble-pile asteroid) compares to the width of the shock, w, generated by impact. Here we further test this hypothesis using impact experiments across a broad range of impact velocities and target grain sizes to systematically vary the ratio between the width of the shock and the diameter of target grains.

Daly, R. T.↗

DOE OSTI2025

Surface and sub-surface porosity effects on the initial free surface expansion in shocked single crystal aluminum

Defects and roughness at a material’s surface can allow for the formation of a material jet when a shockwave reaches a surface. The formation of a jet can lead to significant material damage of the shocked material, as well as the downstream material that the jet impacts. Here, we utilize planar shocks in single crystal aluminum to assess initial jetting formation for surface notches and sub-surface porosity. In the case of surface notches, we find that changing the width of the notch can cause the shock breakout response to transition from a standard jetting mechanism to an atomic atomization at high velocities. This transition occurs due to the mechanisms associated with lateral relaxations within the notch and how this interacts with the shock focusing event that induces jetting. For sub-surface pores, the pore collapse induces a re-shock, localized near the pore, that is stronger than the initial shock, but unsupported. Changing the pore dimensions and location relative to the surface influences the strength of the shock that emanates from its collapse when it reaches the surface, leading to a variety of different breakout conditions including jetting and localized material failure.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Probing Alkylpolyglycoside Hydrogen Bonding and Its Destabilization by Sulfonate Hydrotropes with X‑ray and Vibrational Spectroscopy

It has been proposed that intersurfactant H-bonding networks can produce highly stable foams, specifically those generated from solutions containing alkylpolyglycoside surfactants. In this work, we aim to characterize the presence and destabilization of these networks by introducing a hydrotrope (sodium p-toluene sulfate) at various concentrations into an alkylpolyglycoside (Glucopon 225 DK) surfactant containing solution. Solution surface properties are probed by using aerosol velocity map imaging X-ray photoelectron spectroscopy (A-VMI-XPS) and tensiometer measurements. Bulk properties below the surface are probed using Fourier transform infrared spectroscopy (FTIR) and C-edge near-edge X-ray fine structure spectroscopy (NEXAFS). The surface measurements provide the framework to describe the destabilization of the solution H-bonding network, while the bulk solution measurements provide hints about the disruption of the hydrogen bonding network upon hydrotrope addition. The collected data support the hypothesis that the destabilization of the intersurfactant H-bonding network frees surfactant molecules from the bulk, increasing surfactant population at the air/water interface. This was quantified through an increase in peak area and width in XPS measurements as well as a decrease in surfactant critical micelle concentration. Three regimes with increasing amounts of hydrotrope addition are suggested, described as (1) a hydrotrope affecting only surfactant surface properties, (2) a hydrotrope affecting surfactant surface and bulk properties, and (3) hydrotrope-dominated surface and bulk properties. Future studies will characterize foam stability across the hydrotrope concentration regimes to better define correlations between intersurfactant H-bonding networks and foam stability.

Molecules↗

DOE OSTI2019

Surface Temperature Effect on Convective Heat Transfer Coefficients for Jet Impingement Cooling of Electric Machines with Automatic Transmission Fluid: Preprint

In this study, the results of NREL's continued work on experimental characterization of the thermal performance of free-surface jets of automatic transmission fluid impinged on a heated target surface are presented. The measured heat transfer coefficients are useful for understanding factors influencing performance of driveline fluid-based cooling systems for electric machines and help designers in developing high-performance, power-dense and reliable machines. Experiments were carried out for different fluid and target surface temperatures (50 degrees C, 70 degrees C, and 90 degrees C for the fluid and 90 degrees C, 100 degrees C, 110 degrees C, and 120 degrees C for the target surface). Impinging jet velocities (0.5 m/s to 7.5 m/s) and the jet position on the target surface (center versus edge) were also varied. The impinging angle was kept at 90 degrees relative to the target surface. It was found that higher target surface temperature increased heat transfer coefficients, namely, increasing surface temperature from 90 degrees C to 120 degrees C enhanced heat transfer coefficient values at higher impinged jet velocities (7.5 m/s) by up to 15%.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS1975

Wind tunnel investigation of the wake near the trailing edge of a distributed upper-surface-blown flap

An investigation of the flow field near the trailing edge of a distributed upper-surface-blown propulsive-lift transport was conducted in the Langley V/STOL tunnel. This model used blowing slots across the entire wing span to produce a thin jet efflux near the leading edge and at the knee of the flap. Velocity surveys of the flow field were taken near the trailing edge of the model, and are presented as plots of the individual velocity vectors. The test conditions include an angle-of-attack range from 4 deg to 16 deg and a thrust coefficient range from 0 to 1.3 at a free-stream dynamic pressure of 814 Newton per square meter (17 pounds per square foot).

Forsyth, D. R.↗

NASA NTRS1993

Steady induction effects in geomagnetism. Part 1B: Geomagnetic estimation of steady surficial core motions: A non-linear inverse problem

The problem of estimating a steady fluid velocity field near the top of Earth's core which induces the secular variation (SV) indicated by models of the observed geomagnetic field is examined in the source-free mantle/frozen-flux core (SFI/VFFC) approximation. This inverse problem is non-linear because solutions of the forward problem are deterministically chaotic. The SFM/FFC approximation is inexact, and neither the models nor the observations they represent are either complete or perfect. A method is developed for solving the non-linear inverse motional induction problem posed by the hypothesis of (piecewise, statistically) steady core surface flow and the supposition of a complete initial geomagnetic condition. The method features iterative solution of the weighted, linearized least-squares problem and admits optional biases favoring surficially geostrophic flow and/or spatially simple flow. Two types of weights are advanced radial field weights for fitting the evolution of the broad-scale portion of the radial field component near Earth's surface implied by the models, and generalized weights for fitting the evolution of the broad-scale portion of the scalar potential specified by the models.

Voorhies, Coerte V.↗

NASA NTRS1994

Turbulent Heat Transfer Characteristics in the Shear Layer of a Separated Flow

Experiments were performed to study the evolution of the heat transfer structure in a separated free shear layer region of an incompressible separated turbulent boundary layer flow behind a backward-facing step. While there is an abundance of velocity field measurements of separated flows, heat transfer measurements are rather scarce, thus limiting assessment of the heat transfer physics and its accurate modeling. The purpose of the paper is twofold: to improve an understanding of effects of flow separation on heat transfer characteristics, and to provide data for turbulence modeling and computation. The boundary layer upstream of the step was turbulent and fully developed. A constant temperature surface boundary condition was imposed upstream and downstream of the step for the heat transfer study. An internal mixing-layer like flow forms and grows from the step lip within the original boundary layer. The turbulent structure of the flow evolving downstream, however, does not switch immediately to that of a mixing layer over the entire shear layer thickness. Measurements of mean and fluctuating velocity and temperature fields indicate that the internal layer spreads gradually in the transverse direction while the outer part of the original boundary layer is effectively unperturbed. The results in this paper have not been previously reported.

Jovic, S.↗