Search NASA⌕ Search

SEARCH · Search NASA

Results for “Geometric phase analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Integral Twist Actuation of Helicopter Rotor Blades for Vibration Reduction

Active integral twist control for vibration reduction of helicopter rotors during forward flight is investigated. The twist deformation is obtained using embedded anisotropic piezocomposite actuators. An analytical framework is developed to examine integrally-twisted blades and their aeroelastic response during different flight conditions: frequency domain analysis for hover, and time domain analysis for forward flight. Both stem from the same three-dimensional electroelastic beam formulation with geometrical-exactness, and axe coupled with a finite-state dynamic inflow aerodynamics model. A prototype Active Twist Rotor blade was designed with this framework using Active Fiber Composites as the actuator. The ATR prototype blade was successfully tested under non-rotating conditions. Hover testing was conducted to evaluate structural integrity and dynamic response. In both conditions, a very good correlation was obtained against the analysis. Finally, a four-bladed ATR system is built and tested to demonstrate its concept in forward flight. This experiment was conducted at NASA Langley T~ansonic Dynamics Tunnel and represents the first-of-a-kind Mach-scaled fully-active-twist rotor system to undergo forward flight test. In parallel, the impact upon the fixed- and rotating-system loads is estimated by the analysis. While discrepancies are found in the amplitude of the loads under actuation, the predicted trend of load variation with respect to its control phase correlates well. It was also shown, both experimentally and numerically, that the ATR blade design has the potential for hub vibratory load reduction of up to 90% using individual blade control actuation. Using the numerical framework, system identification is performed to estimate the harmonic transfer functions. The linear time-periodic system can be represented by a linear time-invariant system under the three modes of blade actuation: collective, longitudinal cyclic, and lateral cyclic. A vibration minimizing controller is designed based on this result, which implements classical disturbance rejection algorithm with some modifications. The controller is simulated numerically, and more than 90% of the 4P hub vibratory load is eliminated. By accomplishing the experimental and analytical steps described in this thesis, the present concept is found to be a viable candidate for future generation low-vibration helicopters. Also, the analytical framework is shown to be very appropriate for exploring active blade designs, aeroelastic behavior prediction, and as simulation tool for closed-loop controllers.

Shin, SangJoon↗

Fractal nature structure reconstruction method in designing microstructure properties

Highlights: • Structure and material’s properties, within the material’s consolidation triad: Synthesis – Structure – Properties. • The grain prediction methods is based on the measurements of the solid Euclidean geometric fractal characteristics. • The intergranular contacts inside the BaTiO3 -ceramic are responsible for intergranular capacities. • The inner complex geometry of intergrain contacts imposes fractal correction factor for permeability. - Abstract: In the process of predicting materials properties, it is necessary to predict microstructures. This is important for ceramic materials, for the purpose of miniaturization and for a higher level of integration. Although the method of material structure reconstruction is for the first time used on BaTiO{sub 3}-ceramics by these authors, it can also be used for silicate, refractory and other ceramics, and, for any powder-based material. The reconstruction is based on the grain perimeter fractal analysis and the Richardson method. The main contribution of this paper is establishing the relationship between the electronic properties of BaTiO{sub 3}-ceramics and its microstructural fractal nature. Similar relations can be used for any ceramics or even any materials. The samples consolidation includes both powder pressing (cold sintering phase) and sintering in a furnace (hot sintering phase). The fractal nature characterization has a very important role from the powder phase up to the final microstructure, through which structures it directly impacts electro-physical and other ceramics properties. Thereby, the new possibilities in the microstructure characterization applications are directly introduced to an engineering system, providing the new solutions related to computer aided support. This creates new industrial production and application possibilities, especially in the process of ceramics material consolidation, now based on microstructural properties, which is providing a basis for “fractal electronics’’ development.

36 MATERIALS SCIENCE↗

Microphase Separation Controlled beta-Sheet Crystallization Kinetics in Fibrous Proteins

Silk is a naturally occurring fibrous protein with a multiblock chain architecture. As such, it has many similarities with synthetic block copolymers, including the possibility for e-sheet crystallization restricted within the crystallizable blocks. The mechanism of isothermal crystallization kinetics of e-sheet crystals in silk multiblock fibrous proteins is reported in this study. Kinetics theories, such as Avrami analysis which was established for studies of synthetic polymer crystal growth, are for the first time extended to investigate protein self-assembly in e-sheet rich Bombyx mori silk fibroin samples, using time-resolved Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and synchrotron real-time wide-angle X-ray scattering (WAXS). The Avrami exponent, n, was close to 2 for all methods and crystallization temperatures, indicating formation of e-sheet crystals in silk proteins is different from the 3-D spherulitic crystal growth found in synthetic polymers. Observations by scanning electron microscopy support the view that the protein structures vary during the different stages of crystal growth, and show a microphase separation pattern after chymotrypsin enzyme biodegradation. We present a model to explain the crystallization of the multiblock silk fibroin protein, by analogy to block copolymers: crystallization of e-sheets occurs under conditions of geometrical restriction caused by phase separation of the crystallizable and uncrystallizable blocks. This crystallization model could be widely applicable in other proteins with multiblock (i.e., crystallizable and noncrystallizable) domains.

43 PARTICLE ACCELERATORS↗

Crystal structures of the new ternary stannides La{sub 3}Mg{sub 4−x}Sn{sub 2+x} and LaMg{sub 3−x}Sn{sub 2}

Synthesis and structural characterization of the two new lanthanum–magnesium–stannides La{sub 3}Mg{sub 4−x}Sn{sub 2+x} (0.12≤x≤0.40) and LaMg{sub 3−x}Sn{sub 2} (0.33≤x≤0.78) are reported. The crystal structures of these intermetallics were determined by single crystal X-ray diffraction analysis and confirmed by Rietveld refinement of powder X-ray diffraction patterns of the corresponding samples. The La{sub 3}Mg{sub 4−x}Sn{sub 2+x} phase crystallizes in the hexagonal Zr{sub 3}Cu{sub 4}Si{sub 2} structure type (P6¯2m, hP9, Z=3, x=0.12(1), a=7.7974(7), c=4.8384(4) Å), which represents an ordered derivative of the hP9-ZrNiAl prototype, ubiquitous among equiatomic intermetallics. The LaMg{sub 3–x}Sn{sub 2} phase is the second representative of the trigonal LaMg{sub 3−x}Ge{sub 2} type, which is a superstructure of the LaLi{sub 3}Sb{sub 2} structure type (P3¯1c, hP34-0.12, Z=6, x=0.35(1), a=8.3222(9), c=14.9546(16) Å). The scheme describing the symmetry reduction/coloring with respect to the parent type is reported here with the purpose to discuss the LaMg{sub 3−x}Sn{sub 2} off-stoichiometry from the geometrical point of view. Structural relationships between the La–Mg–Sn ternary phases, including the already known equiatomic LaMgSn compound (oP12-TiNiSi), are presented in the framework of the AlB{sub 2}-related compounds family and discussed with the aid of group-subgroup relations in the Bärnighausen formalism. - Graphical abstract: Crystal structure of LaMg{sub 3−x}Sn{sub 2} viewed along the (001) direction together with the puckered layer of Mg and Sn atoms hosting Mg2, Mg3 and vacancy □. - Highlights: • Crystal structures of the new La{sub 3}Mg{sub 4−x}Sn{sub 2+x} and LaMg{sub 3−x}Sn{sub 2} phases were determined. • The off-stoichiometry of LaMg{sub 3−x}Sn{sub 2} was discussed from geometrical point of view. • Structural relations between the known La–Mg–Sn phases were established. • The studied compounds are related to the AlB{sub 2} type by symmetry reduction.

36 MATERIALS SCIENCE↗

High Temperature Additive Architectures for 65% Efficiency (Final Technical Report)

This project aimed to develop advanced high-temperature additive components that contribute towards the DOE’s goal for advanced gas turbines that are capable of at least 65% efficiency in combined cycle application. The objective was to leverage state-of-the-art additive manufacturing to develop an innovative stage 1 turbine nozzle (S1N) that can provide cooling flow savings while maintaining the component durability expected in today’s gas turbines. The program had two phases. Phase I was a conceptual phase for novel advanced cooling designs enabled by additive manufacturing, as well as proposals for validation. Phase II included execution of the Phase I conceptual design, including manufacturing of prototype hardware and validation within an environment that is similar to engine operation. During Phase I of the program, the team devised a concept to reduce cooling air usage. The cooling air used in the side walls is filmed out along the side walls, while the cooling air used in the airfoil is eventually directed to near-wall channels and exits holes along the airfoil trailing end. During this program, the team performed additive trials to analyze the geometric limitations of additive manufacturing. This helped the team understand minimum wall thicknesses, hole sizes, and cooling channel dimensions among other limits. Phase II of this program pushed GE Vernova beyond its previous experience of designing and manufacturing an additively manufactured hot gas path component. Modern hot gas path components utilize material chemistries that are traditionally hard to weld, such as cast Renè 108, and exhibit solidification cracking when additively manufactured using Direct Metal Laser Melting (DMLM). Note that AM108 is a powder form of Renè 108. A S1N with advanced cooling is larger and more complex than parts previously built by additive manufacturing and required new learnings to resolve risks around solidification cracking. Finally, the team validated the design in a combustion rig that replicated operation in a gas turbine. In order to properly quantify the benefits of the new additive design, a baseline was also tested in the rig and operated under the same conditions. In addition, an uncertainty analysis was done to quantify any sources of error that could impact the results. At the end of the validation effort, it was determined that the additive nozzle exceeded the 15% reduction in cooling flow goal even with the worst-case assumptions for uncertainty.

03 NATURAL GAS↗

A Compact, Tunable Near-UV Source for Quantitative Microgravity Combustion Diagnostics

There is a need for improved optical diagnostic methods for use in microgravity combustion research. Spectroscopic methods with fast time response that can provide absolute concentrations and concentration profiles of important chemical species in flames are needed to facilitate the understanding of combustion kinetics in microgravity. Although a variety of sophisticated laser-based diagnostics (such as planar laser induced fluorescence, degenerate four wave mixing and coherent Raman methods) have been applied to the study of combustion in laboratory flames, the instrumentation associated with these methods is not well suited to microgravity drop tower or space station platforms. Important attributes of diagnostic systems for such applications include compact size, low power consumption, ruggedness, and reliability. We describe a diode laser-based near-UV source designed with the constraints of microgravity research in mind. Coherent light near 420 nm is generated by frequency doubling in a nonlinear crystal. This light source is single mode with a very narrow bandwidth suitable for gas phase diagnostics, can be tuned over several 1/cm and can be wavelength modulated at up to MHz frequencies. We demonstrate the usefulness of this source for combustion diagnostics by measuring CH radical concentration profiles in an atmospheric pressure laboratory flame. The radical concentrations are measured using wavelength modulation spectroscopy (WMS) to obtain the line-of-sight integrated absorption for different paths through the flame. Laser induced fluorescence (LIF) measurements are also demonstrated with this instrument, showing the feasibility of simultaneous WMS absorption and LIF measurements with the same light source. LIF detection perpendicular to the laser beam can be used to map relative species densities along the line-of-sight while the integrated absorption available through WMS provides a mathematical constraint on the extraction of quantitative information from the LIF data. Combining absorption with LIF - especially if the measurements are made simultaneously with the same excitation beam - may allow elimination of geometrical factors and effects of intensity fluctuations (common difficulties with the analysis of LIF data) from the analysis.

Peterson, K. A.↗

The Global Albedo of the Moon at 1064 nm from LOLA

The Lunar Orbiter Laser Altimeter (LOLA) measures the backscattered energy of the returning altimetric laser pulse at its wavelength of 1064 nm, and these data are used to map the reflectivity of the Moon at zero-phase angle with a photometrically uniform data set. Global maps have been produced at 4 pixels per degree (about 8 kilometers at the equator) and 2 kilometers resolution within 20 deg latitude of each pole. The zero-phase geometry is insensitive to lunar topography, so these data enable characterization of subtle variations in lunar albedo, even at high latitudes where such measurements are not possible with the Sun as the illumination source. The geometric albedo of the Moon at 1064 nm was estimated from these data with absolute calibration derived from the Kaguya Multiband Imager and extrapolated to visual wavelengths. The LOLA estimates are within 2 sigma of historical measurements of geometric albedo. No consistent latitude-dependent variations in reflectance are observed, suggesting that solar wind does not dominate space weathering processes that modify lunar reflectance. The average normal albedo of the Moon is found to be much higher than that of Mercury consistent with prior measurements, but the normal albedo of the lunar maria is similar to that of Mercury suggesting a similar abundance of space weathering products. Regions within permanent shadow in the polar regions are found to be more reflective than polar surfaces that are sometimes illuminated. Limiting analysis to data with slopes less than 10 deg eliminates variations in reflectance due to mass wasting and shows a similar increased reflectivity within permanent polar shadow. Steep slopes within permanent shadow are also more reflective than similar slopes that experience at least some illumination. Water frost and a reduction in effectiveness of space weathering are offered as possible explanations for the increased reflectivity of permanent shadow; porosity is largely ruled out as the sole explanation. The south polar crater Shackleton is found to be among the most reflective craters in its size range globally but is not the most reflective, so mass wasting cannot be ruled out as a cause for the crater's anomalous reflectance. Models of the abundance of ice needed to account for the reflectance anomaly range from 3 to 14% by weight or area depending on assumptions regarding the effects of porosity on reflectance and whether ice is present as patches or is well mixed in the regolith. If differences in nanophase iron abundances are responsible for the anomaly, the permanently shadowed regions have between 50 and 80% the abundance of nanophase iron in mature lunar soil.

PSR↗

Shape controlled synthesis of Cu{sub 2}O and its catalytic application to synthesize amorphous carbon nanofibers

Octahedral Cu{sub 2}O particles and Cu{sub 2}O nanowires were synthesized by a simple solution-phase route using N{sub 2}H{sub 4}.H{sub 2}O as reducing agent at room temperature. Amorphous carbon nanofibers were synthesized using octahedral Cu{sub 2}O particles and an acetylene gas source at atmospheric pressure. The samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy and thermogravimetric (TG) analysis. SEM and TEM images indicated that most of the obtained octahedral Cu{sub 2}O particles had an edge length of 400-700 nm. The obtained nanowires had uniform diameters of about 15 nm, and the length of the nanowires ranged from 5 to 10 {mu}m. The XRD result revealed the amorphous feature of the nanofibers. IR spectrum revealed that the nanofibers consist of -CH, -CH{sub 2,} -C=C- and -CH{sub 3} groups. The concentrations of N{sub 2}H{sub 4}.H{sub 2}O and NaOH played important roles in controlling the geometric shape of the Cu{sub 2}O.

36 MATERIALS SCIENCE↗

Aerodynamic-whistles-based ultrasonic tone generators for bat deterrence

Novel ultrasonic bat deterrents based on aerodynamic whistles are proposed and investigated experimentally and numerically for their ability to generate ultrasound. The baseline deterrent, a single-whistle design inspired by Beeken [“Fluid ultrasonic generator,” U.S. patent 3,432,804 (1969)], is examined first. It consists of two resonating cavities/chambers. The whistle is “powered” by a regulated high-pressure air supply, and the performance of the whistle is examined for a range of supply pressures. Far-field acoustic measurements in the 20 Hz–50 kHz frequency range are made in an anechoic chamber. The noise measurements are supplemented with two- and three-dimensional unsteady Reynolds-averaged Navier–Stokes (uRANS) simulations to investigate the mechanisms of ultrasound generation. The Ffowcs Williams–Hawkings acoustic analogy is used with the three-dimensional uRANS results to predict the far-field radiation. The far-field acoustic predictions are in good agreement with the measurements in the anechoic chamber. The peak frequency (fundamental) of the radiated ultrasound of the baseline deterrent is approximately 23 kHz. Harmonics and a sub-harmonic of the fundamental tone are also observed. The numerical simulations show that the two resonating chambers of the baseline deterrent operate out-of-phase and Helmholtz resonance determines the whistling frequency over the range of supply air pressure considered. A six-whistle deterrent targeting a broad spectral coverage in the 20–50 kHz frequency range is designed, fabricated, and tested in the anechoic chamber. Each whistle in the deterrent is obtained by geometrically scaling the baseline whistle. Measurements show that the six-whistle ultrasound deterrent generates ultrasound with six dominant peaks in the designed frequency range when the supply air pressure exceeds 5 psig. The proposed ultrasound devices can be used for a variety of purposes including bat deterrence at wind turbines.

42 ENGINEERING↗

Phase 1 Specifications and preliminary sensitivity analyses of the OECD-NRC liquid metal fast reactor core thermal-hydraulics benchmark

The developments in wire-wrapped fuel bundle thermal-hydraulics research have become increasingly diverse and this makes comparisons across studies difficult. This paper describes an ongoing benchmark that will address this issue by directly comparing computational results with experimental data from two unique wire-wrapped thermal-hydraulic facilities. Preliminary subchannel sensitivity / uncertainty analyses show largely expected behavior for the presented cases, where rod diameter and friction factor show the greatest sensitivities to geometrical perturbations. Guidelines for computational fluid dynamics evaluations have been prepared and highlight the need for consolidated modeling strategies. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Obstruction and Interference in Low-Energy Models for Twisted Bilayer Graphene

The electronic bands of twisted bilayer graphene (TBLG) with a large-period moiré superlattice fracture to form narrow Bloch minibands that are spectrally isolated by forbidden energy gaps from remote dispersive bands. When these gaps are sufficiently large, one can study a band-projected Hamiltonian that correctly represents the dynamics within the minibands. This inevitably introduces nontrivial geometrical constraints that arise from the assumed form of the projection. Here we show that this choice has a profound consequence in a low-energy experimentally observable signature that therefore can be used to tightly constrain the analytic form of the appropriate low-energy theory. Additionally, we find that this can be accomplished by a careful analysis of the electron density produced by backscattering of Bloch waves from an impurity potential localized on the moiré superlattice scale. We provide numerical estimates of the effect that can guide experimental work to clearly discriminate between competing models for the low-energy band structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Further Evidence in Support of the Universal Nilpotent Grammatical Computational Paradigm of Quantum Physics

Further evidence is presented in favour of the computational paradigm, conceived and constructed by Rowlands and Diaz, as detailed in Rowlands' book Zero to Infinity (2007), and in particular the authors' paper 'The Grammatical Universe: the Laws of Thermodynamics and Quantum Entanglement'. The paradigm, which has isomorphic group and algebraic quantum mechanical language interpretations, not only predicts the well-established facts of quantum physics, the periodic table, chemistry / valence and of molecular biology, whose understanding it extends; it also provides an elegant, simple solution to the unresolved quantum measurement problem. In this fundamental paradigm, all the computational constructs / predictions that emerge, follow from the simple fact, that, as in quantum mechanics, the wave function is defined only up to an arbitrary fixed phase. This fixed phase provides a simple physical understanding of the quantum vacuum in quantum field theory, where only relative phases, known to be able to encode 3+1 relativistic space-time geometries, can be measured. It is the arbitrary fixed measurement standard, against which everything that follows is to be measured, even though the standard itself cannot be, since nothing exists against which to measure it. The standard, as an arbitrary fixed reference phase, functions as the holographic basis for a self-organized universal quantum process of emergent novel fermion states of matter where, following each emergence, the arbitrary standard is re-fixed anew so as to provide a complete history / holographic record or hologram of the current fixed past, advancing an unending irreversible evolution, such as is the evidence of our senses. The fermion states, in accord with the Pauli exclusion principle, each correspond to a unique nilpotent symbol in the infinite alphabet (which specifies the grammar in this nilpotent universal computational rewrite system (NUCRS) paradigm); and the alphabet, as Hill and Rowlands hypothesize on substantial evidence [26], includes that of the RNA / DNA genetic code and, as holographic phase encodings / holograms, the 4D geometries of all living systems as self-organised grammatical computational rewrite machines / machinery. Human brains, natural grammatical (written symbol) languages, 4D geometric self-awareness and a totally new emergent property of matter, human consciousness, can thus with some measure of confidence be postulated as further genetic consequences which follow from this self-organizing fundamental rewrite NUCRS construction. For it, like natural language, possesses a semantics and not just a syntax, where the initial symbol, i.e. the arbitrary fixed phase measurement standard, is able to function as the template for the blueprints of the emergent 4D relativistic real and virtual geometries to come, in a 'from the Self Creation to the creation of the human self' computational rewrite process evolution.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Historical photometric evidence for volatile migration on Triton

Analysis of CCD images of Triton obtained with the 1.5-m telescope on Palomar Mountain shows that in the time period surrounding the Voyager 2 encounter with the satellite (1985-1990), no changes in the satellite's visual albedo or color occurred. The published observations of Triton in the 0.35- to 0.60-micrometer spectral region obtained between 1950 and 1990 were reanalyzed to detect historical variability in both its albedo and visual color. Analysis of the photometry indicates that there is little, if any, change in Triton's visual geometric albedo. This result is consistent with the albedo pattern observed by Voyager and the change in sub-Earth latitude. Two distinct types of color changes are evident: a significant secular increase in the blue region of the visual spectrum since at least the 1950s, and the reported dramatic reddening of Triton's spectrum in the late 1970s. The latter change can be explained only by a short-lived geological phenomenon. Triton's changing pole orientation with respect to a terrestrial observer cannot explain the secular color changes. These changes imply volatile transport on a global scale on Triton's surface during the past 4 decades. We present two models which show that either removal of a red volatile from Triton's polar cap or deposition of a blue volatile in the equatorial regions can explain the secular color changes. A third possibility is that the changes are the result of the alpha-beta phase transition of nitrogen and subsequent fracturing of the polar cap region (N. S. Duxbury and R. H. Brown (1993).

Buratti, Bonnie J.↗

Vibration-Based Data Used to Detect Cracks in Rotating Disks

Rotor health monitoring and online damage detection are increasingly gaining the interest of aircraft engine manufacturers. This is primarily due to the fact that there is a necessity for improved safety during operation as well as a need for lower maintenance costs. Applied techniques for the damage detection and health monitoring of rotors are essential for engine safety, reliability, and life prediction. Recently, the United States set the ambitious goal of reducing the fatal accident rate for commercial aviation by 80 percent within 10 years. In turn, NASA, in collaboration with the Federal Aviation Administration, other Federal agencies, universities, and the airline and aircraft industries, responded by developing the Aviation Safety Program. This program provides research and technology products needed to help the aerospace industry achieve their aviation safety goal. The Nondestructive Evaluation (NDE) Group of the Optical Instrumentation Technology Branch at the NASA Glenn Research Center is currently developing propulsion-system-specific technologies to detect damage prior to catastrophe under the propulsion health management task. Currently, the NDE group is assessing the feasibility of utilizing real-time vibration data to detect cracks in turbine disks. The data are obtained from radial blade-tip clearance and shaft-clearance measurements made using capacitive or eddy-current probes. The concept is based on the fact that disk cracks distort the strain field within the component. This, in turn, causes a small deformation in the disk's geometry as well as a possible change in the system's center of mass. The geometric change and the center of mass shift can be indirectly characterized by monitoring the amplitude and phase of the first harmonic (i.e., the 1 component) of the vibration data. Spin pit experiments and full-scale engine tests have been conducted while monitoring for crack growth with this detection methodology. Even so, published data are extremely limited, and the basic foundation of the methodology has not been fully studied. The NDE group is working on developing this foundation on the basis of theoretical modeling as well as experimental data by using the newly constructed subscale spin system shown in the preceding photograph. This, in turn, involved designing an optimal sub-scale disk that was meant to represent a full-scale turbine disk; conducting finite element analyses of undamaged and damaged disks to define the disk's deformation and the resulting shift in center of mass; and creating a rotordynamic model of the complete disk and shaft assembly to confirm operation beyond the first critical concerning the subscale experimental setup. The finite element analysis data, defining the center of mass shift due to disk damage, are shown. As an example, the change in the center of mass for a disk spinning at 8000 rpm with a 0.963-in. notch was 1.3 x 10(exp -4) in. The actual vibration response of an undamaged disk as well as the theoretical response of a cracked disk is shown. Experiments with cracked disks are continuing, and new approaches for analyzing the captured vibration data are being developed to better detect damage in a rotor. In addition, the subscale spin system is being used to test the durability and sensitivity of new NDE sensors that focus on detecting localized damage. This is designed to supplement the global response of the crack-detection methodology described here.

Gyekenyesi, Andrew L.↗

A switched state feedback law for the stabilization of LTI systems.

Inspired by prior work in the design of switched feedback controllers for second order systems, we develop a switched state feedback control law for the stabilization of LTI systems of arbitrary dimension. The control law operates by switching between two static gain vectors in such a way that the state trajectory is driven onto a stable n - 1 dimensional hyperplane (where n represents the system dimension). We begin by briefly examining relevant geometric properties of the phase portraits in the case of two-dimensional systems to develop intuition, and we then show how these geometric properties can be expressed as algebraic constraints on the switched vector fields that are applicable to LTI systems of arbitrary dimension. We then derive necessary and sufficient conditions to ensure stabilizability of the resulting switched system (characterized primarily by simple conditions on eigenvalues), and describe an explicit procedure for designing stabilizing controllers. We then show how the newly developed control law can be applied to the problem of minimizing the maximal Lyapunov exponent of the corresponding closed-loop state trajectories, and we illustrate the closed-loop transient performance of these switched state feedback controllers via multiple examples.

42 ENGINEERING↗

Curvature distribution and autocorrelations in elliptic cylinders and cones

Not all micro-vessels (MV) are traditionally circular and there are examples of elliptic cylindrical MVs in life sciences, particularly if projected with a slant. Similarly, certain biological structures, ferroelectric liquid crystals, aluminum oxide clusters and witherite crystallites’ crosssection appear to be elliptical cones. We studied the mean curvature (H) distribution of these elliptic morphological structures with geometric parameter such as eccentricity; e (ratio of semi-minor to semi-major axes) and a measure of how much diagonal section deviates from circularity and height (h) in case of cones. By means of topographical cues, we defined the curvature-curvature autocorrelation function (gk) and applied this notion to mean curvature (H) of circular and elliptical cylinders and cones. The Fourier transform of correlation function, i.e. “curvature factor” is analogous to “structure factor (or Patterson function)” in X-ray and neutron scattering intensity. It elucidates critically important information related to surface curvature fluctuation relevant to shape (geometry), network and phase transformation. The latter is induced by cells under mechanical stress, occurring in many soft systems (polymeric liquid crystals, foams, bubbles) and biological tissues, particularly cell walls of primary and branched vessels bed in microvasculature that distributes blood within tissue during hypertension and migraines. This perspective is useful in a sustained release of angiogenic/vasculogenic factors and relevant for precision medicine and engineered microvessels and tissues in vitro and in vivo extended cellular processes. The quantitative analysis carried out in this work facilitates our understanding of the mechanical mechanisms associated with thrombosis during surgery that typically occur in bent or stretched MVs due to microenvironment such as localized shear stresses and biochemical factors.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Mixing of an Airblast-atomized Fuel Spray Injected into a Crossflow of Air

The injection of a spray of fuel droplets into a crossflow of air provides a means of rapidly mixing liquid fuel and air for combustion applications. Injecting the liquid as a spray reduces the mixing length needed to accommodate liquid breakup, while the transverse injection of the spray into the air stream takes advantage of the dynamic mixing induced by the jet-crossflow interaction. The structure of the spray, formed from a model plain-jet airblast atomizer, is investigated in order to determine and understand the factors leading to its dispersion. To attain this goal, the problem is divided into the following tasks which involve: (1) developing planar imaging techniques that visualize fuel and air distributions in the spray, (2) characterizing the airblast spray without a crossflow, and (3) characterizing the airblast spray upon injection into a crossflow. Geometric and operating conditions are varied in order to affect the atomization, penetration, and dispersion of the spray into the crossflow. The airblast spray is first characterized, using imaging techniques, as it issues into a quiescent environment. The spray breakup modes are classified in a liquid Reynolds number versus airblast Weber number regime chart. This work focuses on sprays formed by the "prompt" atomization mode, which induces a well-atomized and well-dispersed spray, and which also produces a two-lobed liquid distribution corresponding to the atomizing air passageways in the injector. The characterization of the spray jet injected into the crossflow reveals the different processes that control its dispersion. Correlations that describe the inner and outer boundaries of the spray jet are developed, using the definition of a two-phase momentum-flux ratio. Cross-sections of the liquid spray depict elliptically-shaped distributions, with the exception of the finely-atomized sprays which show kidney-shaped distributions reminiscent of those obtained in gaseous jet in crossflow systems. A droplet trajectory analysis overpredicts the liquid mass penetration, and indicates a need for a more rigorous model to account for the three-dimensional mixing field induced by the jet-crossflow interaction. Nonetheless, the general procedures and criteria that are outlined can be used to efficiently assess and compare the quality of sprays formed under different conditions.

Leong, May Y.↗

UNDERSTANDING TRENDS ASSOCIATED WITH CLOUDS IN IRRADIATED EXOPLANETS

Unlike previously explored relationships between the properties of hot Jovian atmospheres, the geometric albedo and the incident stellar flux do not exhibit a clear correlation, as revealed by our re-analysis of Q0-Q14 Kepler data. If the albedo is primarily associated with the presence of clouds in these irradiated atmospheres, a holistic modeling approach needs to relate the following properties: the strength of stellar irradiation (and hence the strength and depth of atmospheric circulation), the geometric albedo (which controls both the fraction of starlight absorbed and the pressure level at which it is predominantly absorbed), and the properties of the embedded cloud particles (which determine the albedo). The anticipated diversity in cloud properties renders any correlation between the geometric albedo and the stellar flux weak and characterized by considerable scatter. In the limit of vertically uniform populations of scatterers and absorbers, we use an analytical model and scaling relations to relate the temperature-pressure profile of an irradiated atmosphere and the photon deposition layer and to estimate whether a cloud particle will be lofted by atmospheric circulation. We derive an analytical formula for computing the albedo spectrum in terms of the cloud properties, which we compare to the measured albedo spectrum of HD 189733b by Evans et al. Furthermore, we show that whether an optical phase curve is flat or sinusoidal depends on whether the particles are small or large as defined by the Knudsen number. This may be an explanation for why Kepler-7b exhibits evidence for the longitudinal variation in abundance of condensates, while Kepler-12b shows no evidence for the presence of condensates despite the incident stellar flux being similar for both exoplanets. We include an 'observer's cookbook' for deciphering various scenarios associated with the optical phase curve, the peak offset of the infrared phase curve, and the geometric albedo.

79 ASTRONOMY AND ASTROPHYSICS↗