Search NASA⌕ Search

SEARCH · Search NASA

Results for “HYPERSONIC BOUNDARY LAYER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Initial operation of the UTA shock tunnel

Initial experience in operating a small UTA (University of Texas at Arlington) shock tunnel at high Reynolds numbers for perfect gas simulation of hypersonic flow and boundary layer studies is described. Particular attention is given to tradeoffs between various constraints for achieving the test requirements, and methods for obtaining precise control of test conditions and protecting low-range pressure transducers from overpressure damage.

Lu, Frank K.↗
NASA NTRS2000

Pegasus(Registered trademark) Wing-Glove Experiment to Document Hypersonic Crossflow Transition: Measurement System and Selected Flight Results

In a recent flight experiment to study hypersonic crossflow transition, boundary layer characteristics were documented. A smooth steel glove was mounted on the first stage delta wing of Orbital Sciences Corporation's Pegasus (R) launch vehicle and was flown at speeds of up to Mach 8 and altitudes of up to 250,000 ft. The wing-glove experiment was flown as a secondary payload off the coast of Florida in October 1998. This paper describes the measurement system developed. Samples of the results obtained for different parts of the trajectory are included to show the characteristics and quality of the data. Thermocouples and pressure sensors (including Preston tubes, Stanton tubes, and a "probeless" pressure rake showing boundary layer profiles) measured the time-averaged flow. Surface hot-films and high-frequency pressure transducers measured flow dynamics. Because the vehicle was not recoverable, it was necessary to design a system for real-time onboard processing and transmission. Onboard processing included spectral averaging. The quality and consistency of data obtained was good and met the experiment requirements.

Bertelrud, Arild↗
NASA NTRS1995

A Numerical Investigation of the Burnett Equations Based on the Second Law

The Burnett equations have been shown to potentially violate the second law of thermodynamics. The objective of this investigation is to correlate the numerical problems experienced by the Burnett equations to the negative production of entropy. The equations have had a long history of numerical instability to small wavelength disturbances. Recently, Zhong corrected the instability problem and made solutions attainable for one dimensional shock waves and hypersonic blunt bodies. Difficulties still exist when attempting to solve hypersonic flat plate boundary layers and blunt body wake flows, however. Numerical experiments will include one-dimensional shock waves, quasi-one dimensional nozzles, and expanding Prandlt-Meyer flows and specifically examine the entropy production for these cases.

Comeaux, Keith A.↗
NASA NTRS2021

Hypersonic Second Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗
NASA NTRS2024

A Summary of the 2023 Joint High-Speed Boundary Layer Transition Workshop

A joint workshop between the Air Force Office of Scientific Research, the Office of Naval Research, and the NASA Hypersonic Technology Project was held in June 2023 on the topic of high-speed boundary-layer transition. The purpose of this workshop was to gather subject matter experts in the areas of supersonic and hypersonic boundary-layer transition in the areas of geometries of interest, computational methods, facilities and diagnostics, flight experiments, flow control, and new approaches and to discuss the current state of the art in the field. As gaps and accomplishments were identified, roadmaps were also created to guide future investments in these areas. The top recommendations are (1) to define relevant common geometries of interest that can be worked by multiple research groups; (2) improve modeling of high-enthalpy flows involving chemistry and ablation, studies of receptivity of freestream disturbances and atmospheric particulates into the boundary layer, surface feature characterization and modeling of changes to geometry; (3) design and determine viable flow control methods; and (4) move towards incorporating boundary layer transition prediction into a standard practice for design of high-speed vehicles. To execute this last recommendation successfully, investments beyond fundamental (basic and early applied) research are needed.

boundary layer transition↗
NASA NTRS1975

Analytical formulas for conditions on blunt wedges in hypersonic flow

An analytical approximation is obtained to the solution of the equation describing the combined effects of bluntness and boundary-layer displacement on the hypersonic flow over a wedge for the case where the constant parameter in the governing equation, which is proportional to the angle of attack, is greater than zero. It is shown that the approximation has good physical accuracy over the entire range of conditions to which the theory is applicable for positive angle of attack.

Bade, W. L.↗
NASA NTRS1957

Exploratory Investigation of Boundary-Layer Transition on a Hollow Cylinder at a Mach Number of 6.9

The Reynolds number for transition on the outside of a hollow cylinder with heat transfer from the boundary layer to the wall has been investigated at a Mach number of 6.9 in the Langley 11-inch hypersonic tunnel. The type of boundary layer was determined from impact-pressure surveys and optical viewing. From a correlation of results obtained from various sources at lower Mach numbers (in the range 2.0 to 4.5) and data from the present tests with variable Reynolds number per inch, leading-edge thickness and free-stream Reynolds number per inch appear to be important considerations in flat-plate transition results. At a given Mach number, it appears that the Reynolds number based on leading-edge thickness is an important parameter that must be considered in comparisons of flat-plate transition data from various installations.

Bertram, Mitchel H↗
NASA NTRS2015

HIFiRE-1 Turbulent Shock Boundary Layer Interaction - Flight Data and Computations

The Hypersonic International Flight Research Experimentation (HIFiRE) program is a hypersonic flight test program executed by the Air Force Research Laboratory (AFRL) and Australian Defence Science and Technology Organisation (DSTO). This flight contained a cylinder-flare induced shock boundary layer interaction (SBLI). Computations of the interaction were conducted for a number of times during the ascent. The DPLR code used for predictions was calibrated against ground test data prior to exercising the code at flight conditions. Generally, the computations predicted the upstream influence and interaction pressures very well. Plateau pressures on the cylinder were predicted well at all conditions. Although the experimental heat transfer showed a large amount of scatter, especially at low heating levels, the measured heat transfer agreed well with computations. The primary discrepancy between the experiment and computation occurred in the pressures measured on the flare during second stage burn. Measured pressures exhibited large overshoots late in the second stage burn, the mechanism of which is unknown. The good agreement between flight measurements and CFD helps validate the philosophy of calibrating CFD against ground test, prior to exercising it at flight conditions.

Turbulence↗
DOE OSTI2020

HTR solver: An open-source exascale-oriented task-based multi-GPU high-order code for hypersonic aerothermodynamics

In this study, the open-source Hypersonics Task-based Research (HTR) solver for hypersonic aerothermodynamics is described. The physical formulation of the code includes thermochemical effects induced by high temperatures (vibrational excitation and chemical dissociation). The HTR solver uses high-order TENO-based spatial discretization on structured grids and efficient time integrators for stiff systems, is highly scalable in GPU-based supercomputers as a result of its implementation in the Regent/Legion stack, and is designed for direct numerical simulations of canonical hypersonic flows at high Reynolds numbers. Additionally, the performance of the HTR solver is tested with benchmark cases including inviscid vortex advection, low- and high-speed laminar boundary layers, inviscid one-dimensional compressible flows in shock tubes, supersonic turbulent channel flows, and hypersonic transitional boundary layers of both calorically perfect gases and dissociating air.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1972

Experimental boundary-layer edge Mach numbers for two space shuttle orbiters at hypersonic speeds

Pitot-pressure profiles and surface pressure measurements have been obtained at four axial stations along the center lines of space shuttle straight-wing and delta-wing orbiters at angles of attack from 20 deg to approximately 60 deg and Mach numbers of 20.3 (helium) and 6.8 (air). The results show that the Mach number at the edge of the boundary layer is best predicted by tangent-cone theory up to shock detachment.

Ashby, G. C., Jr.↗