Search NASA⌕ Search

SEARCH · Search NASA

Results for “INDUCTIVE CHARGING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Sudden-Discharge Cycling Characteristics and Millisecond Dynamic Behaviors of a HTS Stainless-Steel Insulated Double-Pancake Coil With Thin Copper Plates

We have tested an intermediate-sized HTS stainless-steel (co-wound) insulated double pancake coil (~132 turns per coil) and discovered dynamic effects during sudden discharge on both millisecond and second scales. For soft break, the power supply is turned off suddenly but the shunt resistor (164 milliohm) is still connected; for hard break, a high voltage contactor is used to suddenly open the circuit so that the leads are completely open. Hard break is dangerous to traditionally insulated LTS magnets, but the SS-insulated HTS DPC retained integrity over ¡80 charge-discharge cycles. Voltage decay curves for soft and hard breaks are studied on short and long timescales. On long timescales, we observe the expected exponential decay and measure the time constant to calculate contact resistance. On short timescales, we observe highly dynamic effects: a hyper-exponential decay suggesting that the inductance or contact resistance is suddenly changing with time, likely an indication of the RL circuit forming. Moreover, peak voltage immediately (ms) after the sudden discharge were collected and compared. It is found that the peak voltage in soft-discharge is proportional to the applied current, while the those in hard-break has a unique pattern and tends to stay flat even though the applied current increases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Altitude Performance of Allison V-1710-93 Engine and Two-Stage Supercharger

Bench tests have been made of an Allison V-1710-93 engine at simulated altitudes of 17,000 and 29,000 feet to determine the performance of the engine, the characteristics of the induction system, and the modifications required in the induction system for the center dot development of 1840 brake horsepower at 17,030 feet and 1200 horsepower at 29,000 feet. With the engine speed maintained at a constant value of 3000 rpm, the tip speed of the auxiliary-stage supercharger was varied from the minimum to the maximum speed. Measurements were made to determine engine power, fuel and air consumptions, and pressure and temperature changes introduced by each component of the induction system. Although the over-all pressure ratios of the superchargers agreed with those determined from previous sea-level bench tests of these units, the over-all temperature rise was -generally much lower than had been anticipated. In order to obtain the desired brake horsepower, some form of charge-air cooling is essential; the carburetor should either be enlarged or removed; and the minimum gear ratios of the engine-stage and the minimum gear ratios of the engine-stage and the auxiliary-stage superchargers should be 8.1:1 and 8.08:1, respectively.

Edward Glodeck↗

2D Model of a Tandem Plasma Source: The Role of the Transport Processes

A 2D fluid-plasma model of a tandem two-chamber plasma source operating in hydrogen gas is presented in the study. The configuration of the source is of the type of the inductively-driven sources developed for neutral beam injection heating of fusion plasmas: the rf power deposition is in the first smaller-radius chamber of the source and the second bigger-radius chamber is a volume for plasma expansion from the driver. Plasma maintenance in the source governed by transport processes--charged-particle and electron-energy fluxes--is the main conclusion stemming from the results. Moreover, the metal walls of the source and its different dimensions in the longitudinal and transverse directions determine a regime of a rf discharge characterized by a dc current in the source: electrons and ions flowing in different directions determine a solenoidal current in the discharge. This is accompanied by a strong drop of electron temperature, charged-particle and hydrogen-atom densities and plasma potential at the transition between the two chambers of the source. In general, the results from the model lead to the conclusion that analysis of the transport processes should be in the basis of the optimization of the tandem-plasma-source operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Quasinormal modes, scattering, and Hawking radiation of Kerr-Newman black holes in a magnetic field

We perform a comprehensive analysis of the spectrum of proper oscillations (quasinormal modes), transmission/reflection coefficients, and Hawking radiation for a massive charged scalar field in the background of the Kerr-Newman black hole immersed in an asymptotically homogeneous magnetic field. There are two main effects: the Zeeman shift of the particle energy in the magnetic field and the difference of values of an electromagnetic potential between the horizon and infinity, i.e. the Faraday induction. We have shown that 'turning on' the magnetic field induces a stronger energy-emission rate and leads to 'recharging' of the black hole. Thus, a black hole immersed in a magnetic field evaporates much quicker, achieving thereby an extremal state in a shorter period of time. Quasinormal modes are moderately affected by the presence of a magnetic field which is assumed to be relatively small compared to the gravitational field of the black hole.

79 ASTRONOMY AND ASTROPHYSICS↗

Investigation of Icing Characteristics of Typical Light Airplane Engine Induction Systems

The icing characteristics of two typical light-airplane engine induction systems were investigated using the carburetors and manifolds of engines in the horsepower ranges from 65 to 85 and 165 to 185. The smaller system consisted of a float-type carburetor with an unheated manifold and the larger system consisted of a single-barrel pressure-type carburetor with an oil-jacketed manifold. Carburetor-air temperature and humidity limits of visible and serious Icing were determined for various engine power conditions. Several.methods of achieving ice-free induction systems are discussed along with estimates of surface heating requirements of the various induct ion-system components. A study was also made of the icing characteristics of a typical light-airplane air scoop with an exposed filter and a modified system that provided a normal ram inlet with the filter located in a position to Induce inertia separation of the free water from the charge air. The principle of operation of float-type carburetors is proved to make them inherently more susceptible to icing at the throttle plate than pressure-type carburetors.. The results indicated that proper jacketing and heating of all parts exposed to the fuel spray can satisfactorily reduce or eliminate icing in the float-type carburetor and the manifold. Pressure-type carburetors can be protected from serious Icing by proper location of the fuel-discharge nozzle combined with suitable application of heat to critical parts.

Coles, W. D.↗

Transport of cosmic ray nuclei in various materials

Cosmic-ray heavy ions have become a concern in space radiation effects analyses. Heavy ions rapidly deposit energy and create dense ionization trails as they traverse materials. Collection of the free charge disrupts the operation of microelectronic circuits. This effect, called the single-event upset, can cause a loss of digital data. Passage of high linear energy transfer particles through the eyes has been observed by Apollo astronauts. These heavy ions have great radiobiological effectiveness and are the primary risk factor for leukemia induction on a manned Mars mission. Models of the transport of heavy cosmic-ray nuclei through materials depend heavily on our understanding of the cosmic-ray environment, nuclear spallation cross sections, and computer transport codes. Our group has initiated and pursued the development of a full capability for modeling these transport processes. A recent review of this ongoing effort is presented in Ref. 5. In this paper, we discuss transport methods and present new results comparing the attenuation of cosmic rays in various materials.

NASA Discipline Radiation Health↗

Controlling hollow relativistic electron beam orbits with an inductive current divider

A passive method for controlling the trajectory of an intense, hollow electron beam is proposed using a vacuum structure that inductively splits the beam's return current. A central post carries a portion of the return current (I{sub 1}), while the outer conductor carries the remainder (I{sub 2}). An envelope equation appropriate for a hollow electron beam is derived and applied to the current divider. The force on the beam trajectory is shown to be proportional to (I{sub 2}-I{sub 1}), while the average force on the envelope (the beam width) is proportional to the beam current I{sub b} = (I{sub 2} + I{sub 1}). The values of I{sub 1} and I{sub 2} depend on the inductances in the return-current path geometries. Proper choice of the return-current geometries determines these inductances and offers control over the beam trajectory. Solutions using realistic beam parameters show that, for appropriate choices of the return-current-path geometry, the inductive current divider can produce a beam that is both pinched and straightened so that it approaches a target at near-normal incidence with a beam diameter that is on the order of a few mm.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A New Approach to Reduce Uncertainties in Space Radiation Cancer Risk Predictions

The prediction of space radiation induced cancer risk carries large uncertainties with two of the largest uncertainties being radiation quality and dose-rate effects. In risk models the ratio of the quality factor (QF) to the dose and dose-rate reduction effectiveness factor (DDREF) parameter is used to scale organ doses for cosmic ray proton and high charge and energy (HZE) particles to a hazard rate for γ-rays derived from human epidemiology data. In previous work, particle track structure concepts were used to formulate a space radiation QF function that is dependent on particle charge number Z, and kinetic energy per atomic mass unit, E. QF uncertainties where represented by subjective probability distribution functions (PDF) for the three QF parameters that described its maximum value and shape parameters for Z and E dependences. Here I report on an analysis of a maximum QF parameter and its uncertainty using mouse tumor induction data. Because experimental data for risks at low doses of γ-rays are highly uncertain which impacts estimates of maximum values of relative biological effectiveness (RBE max ), I developed an alternate QF model, denoted QF γAcute where QFs are defined relative to higher acute γ-ray doses (0.5 to 3 Gy). The alternate model reduces the dependence of risk projections on the DDREF, however a DDREF is still needed for risk estimates for high-energy protons and other primary or secondary sparsely ionizing space radiation components. Risk projections (upper confidence levels (CL)) for space missions show a reduction of about 40% (CL~50%) using the QF γAcute model compared the QFs based on RBE max and about 25% (CL~35%) compared to previous estimates. In addition, I discuss how a possible qualitative difference leading to increased tumor lethality for HZE particles compared to low LET radiation and background tumors remains a large uncertainty in risk estimates.

59 BASIC BIOLOGICAL SCIENCES↗

A Kp dependent equatorial electric field model

A new model of the earth's electric field in the equatorial plane has been constructed. While many models have been proposed, most of these have had serious shortcomings. They either have only a few parameters and cannot hope to match even large scale variations in the real field, or they are too complex to be suitable starting points for constructing time dependent three dimensional models which include inductive fields. Also, few previous models have a continuous functional dependence upon magnetic disturbance levels. The new model uses only a dozen parameters and yet fits many of the known dependences upon radial distance, local time, and magnetic disturbance level. One of the roles of electric field models is to predict and understand the motion of charged particles. Models like this one which are based upon a time dependent scalar potential can greatly help in the understanding of the motion of equatorial particles during the time periods between substorms.

Mcilwain, C. E.↗

Induction time of a polymorphic transformation

When a solution is supersaturated with respect to multiple polymorphs, the polymorph with the lowest nucleation barrier will form first. If this is a metastable polymorph, it will persist until the induction of nuclei of a lower free-energy phase, marking the onset of a polymorphic transformation. Induction of a more stable polymorph can occur under two conditions: a.) during steady-state nucleation, or b.) after complete crystal growth of the metastable phase. Using the theory of competing stochastic processes, we derive the rare probability of forming a higher-barrier, more-stable polymorph during steady-state nucleation, and use this to explain variations in crystallization products between repeat experiments, which may underlie the phenomenon of "Disappearing Polymorphs". We also derive the induction time of a stable phase from a solution equilibrated with a metastable phase, and show that once the stable phase nucleates, bulk metastable crystals will spontaneously ripen onto nanoscale nuclei or seeds of a more stable phase, thermodynamically driving dissolution-reprecipitation processes. Existing strategies to prolong or shorten the lifetimes of transient metastable phases are reviewed and interpreted within the context of polymorphic induction. Finally, the analyses in this work are conducted from classical nucleation and crystal growth theories, suggesting that paradigms shifts to 'non-classical' nucleation theories may not be necessary to rationalize multistage crystallization.

36 MATERIALS SCIENCE↗

Induction of a bystander mutagenic effect of alpha particles in mammalian cells

Ever since the discovery of X-rays was made by Rontgen more than a hundred years ago, it has always been accepted that the deleterious effects of ionizing radiation such as mutation and carcinogenesis are attributable mainly to direct damage to DNA. Although evidence based on microdosimetric estimation in support of a bystander effect appears to be consistent, direct proof of such extranuclear/extracellular effects are limited. Using a precision charged particle microbeam, we show here that irradiation of 20% of randomly selected A(L) cells with 20 alpha particles each results in a mutant fraction that is 3-fold higher than expected, assuming no bystander modulation effect. Furthermore, analysis by multiplex PCR shows that the types of mutants induced are significantly different from those of spontaneous origin. Pretreatment of cells with the radical scavenger DMSO had no effect on the mutagenic incidence. In contrast, cells pretreated with a 40 microM dose of lindane, which inhibits cell-cell communication, significantly decreased the mutant yield. The doses of DMSO and lindane used in these experiments are nontoxic and nonmutagenic. We further examined the mutagenic yield when 5-10% of randomly selected cells were irradiated with 20 alpha particles each. Results showed, likewise, a higher mutant yield than expected assuming no bystander effects. Our studies provide clear evidence that irradiated cells can induce a bystander mutagenic response in neighboring cells not directly traversed by alpha particles and that cell-cell communication process play a critical role in mediating the bystander phenomenon.

Non-NASA Center↗

Plasma Physics found in JT-60 Tokamak over the Last 20 years

This paper summarizes major plasma physics obtained during the period of JT-60 operation for 23 years with special emphasis on research towards steady-state operation of tokamak. Topics included are observation of large bootstrap current fraction, negative shear scenario, demonstration of efficient beam and EC current drive, discovery of current hole, stabilization of the RWM, discovery of ITB (internal transport barrier).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spatial calibration of a tokamak neutral beam diagnostic using in situ neutral beam emission

Neutral beam injection is used in tokamaks to heat, apply torque, drive non-inductive current, and diagnose plasmas. Neutral beam diagnostics need accurate spatial calibrations to benefit from the measurement localization provided by the neutral beam. A new technique has been developed that uses in situ measurements of neutral beam emission to determine the spatial location of the beam and the associated diagnostic views. This technique was developed to improve the charge exchange recombination (CER) diagnostic at the DIII-D tokamak and uses measurements of the Doppler shift and Stark splitting of neutral beam emission made by that diagnostic. These measurements contain information about the geometric relation between the diagnostic views and the neutral beams when they are injecting power. This information is combined with standard spatial calibration measurements to create an integrated spatial calibration that provides a more complete description of the neutral beam-CER system. The integrated spatial calibration results are very similar to the standard calibration results and derived quantities from CER measurements are unchanged within their measurement errors. The methods developed to perform the integrated spatial calibration could be useful for tokamaks with limited physical access.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Transuranium Sulfide via the Boron Chalcogen Mixture Method and Reversible Water Uptake in the NaCu T S 3 Family

The behavior of 5f electrons in soft ligand environments makes actinides, and especially transuranium chalcogenides, an intriguing class of materials for fundamental studies. Due to the affinity of actinides for oxygen, however, it is a challenge to synthesize actinide chalcogenides using non-metallic reagents. Using the Boron Chalcogen Mixture (BCM) method, we achieved the synthesis of the transuranium sulfide NaCuNpS 3 starting from the oxide reagent, NpO 2 . Via the same synthetic route, the isostructural composition of NaCuUS 3 was synthesized and the material contrasted with NaCuNpS 3 . Single crystals of the U-analog, NaCuUS 3 , were found to undergo an unexpected reversible hydration process to form NaCuUS 3 ·xH 2 O (x ≈ 1.5). Here, a large combination of techniques was used to fully characterize the structure, hydration process, and electronic structures, specifically a combination of single crystal, powder, high temperature powder X-ray diffraction, extended X-ray ab-sorption fine structure, infrared, and inductively coupled plasma spectroscopies, thermogravimetric analysis, and density functional theory calculations. The outcome of these analyses enabled us to determine the composition of NaCuUS 3 ·xH 2 O and obtain a structural model that demonstrated the retention of the local structure within the [CuUS 3 ] – layers throughout the hydration-dehydration process. Band structure, density of states, and Bader charge calculations for NaCuUS 3 , NaCu-US 3 ·xH 2 O, and NaCuNpS 3 along with X-ray absorption near edge structure, UV-vis-NIR and work function measurements on ACuUS 3 (A = Na, K, and Rb) and NaCuUS 3 ·xH 2 O samples were carried out to demonstrate that electronic properties arise from the [CuTS 3 ] – layers and show surprisingly little dependence on the interlayer distance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Differential etching behavior between semi-insulating and n-doped 4H-SiC in high-density SF{sub 6}/O{sub 2} inductively coupled plasma

The author investigated the etching characteristics of semi-insulating (SI) and n-doped (n-) 4H-SiC substrates at a high etch rate of about 2 {mu}m/min using high-density SF{sub 6}/O{sub 2} inductively coupled plasma. The etch rate of SI-SiC was found to be lower than that of n-SiC, and the etching profile of SI-SiC showed retrograde features with a larger sidewall angle and a rounder etched bottom compared to n-SiC. These characteristics are attributed to the difference in wafer heating and negative charging of the sidewall during plasma etching between both substrates. The temperature of n-SiC increases by radiative heating from the high-density plasma during etching because of the higher free-carrier absorption compared to SI-SiC. Furthermore, the negative charge buildup at the sidewall of SI-SiC becomes stronger because of the lower electrical conductivity compared to n-SiC.

36 MATERIALS SCIENCE↗

Integral inverter/battery charger for use in electric vehicles

The design and test results of a thyristor based inverter/charger are discussed. A battery charger is included integral to the inverter by using a subset of the inverter power circuit components. The resulting charger provides electrical isolation between the vehicle propulsion battery and ac line and is capable of charging a 25 kWh propulsion battery in 8 hours from a 220 volt ac line. The integral charger employs the inverter commutation components at a resonant ac/dc isolated converter rated at 3.6 kW. Charger efficiency and power factor at an output power of 3.6 kW are 86% and 95% respectively. The inverter, when operated with a matching polyphase ac induction motor and nominal 132 volt propulsion battery, can provide a peak shaft power of 34 kW (45 ph) during motoring operation and 45 kW (60 hp) during regeneration. Thyristors are employed for the inverter power switching devices and are arranged in an input-commutated topology. This configuration requires only two thyristors to commutate the six main inverter thyristors. Inverter efficiency during motoring operation at motor shaft speeds above 450 rad/sec (4300 rpm) is 92-94% for output power levels above 11 KW (15 hp). The combined ac inverter/charger package weighs 47 kg (103 lbs).

Thimmesch, D.↗

Multiport Control with Partial Power Processing in Solid-State Transformer for PV, Storage, and Fast-Charging Electric Vehicle Integration

This article proposes a multiport control method to enable partial power processing (PPP) in a medium-voltage (MV) multiport solid-state transformer (SST). MV multiport SSTs are promising in integrating low-voltage DC sources or loads such as solar photovoltaic, energy storage, and electric vehicles into smart grids without bulky line-frequency transformers. Compared to voltage-source SST, current-source (CS) SST features single-stage isolated bidirectional AC/AC, AC/DC, or DC/DC conversion using an inductive DC link. For a multiport CS SST, it is revealed in this article that the PPP capability can be enabled through the proposed control without extra hardware, different from the case of voltage-source converters where special hardware architecture is required for the PPP. With the PPP, most power exchange between LV ports is processed by only a fraction of the entire conversion stage, leading to reduced DC-link current, volume, loss, and improved efficiency. The proposed multiport PPP control scheme is analyzed to verify the advantages across a wide voltage and power range against conventional full power processing (FPP) multiport control, using the soft-switching solid-state transformer (S4T) with reduced conduction loss as an example. Comparative experimental results based on a SiC three-port S4T prototype verify the effectiveness of the proposed PPP scheme against the FPP scheme under both steady state and dynamic conditions. Here, the DC-link current reduction is measured to be more than 36%. Significantly, the proposed multiport PPP control scheme is generic and applicable to any hard-switching or soft-switching CS SSTs without extra hardware.

14 SOLAR ENERGY↗

Heating and current drive requirements towards steady state operation in ITER

Steady state scenarios envisaged for ITER aim at optimizing the bootstrap current, while maintaining sufficient confinement and stability to provide the necessary fusion yield. Non-inductive scenarios will need to operate with Internal Transport Barriers (ITBs) in order to reach adequate fusion gain at typical currents of 9 MA. However, the large pressure gradients associated with ITBs in regions of weak or negative magnetic shear can be conducive to ideal MHD instabilities, reducing the no-wall limit. The E × B flow shear from toroidal plasma rotation is expected to be low in ITER, with a major role in the ITB dynamics being played by magnetic geometry. Combinations of H/CD sources that maintain weakly reversed magnetic shear profiles throughout the discharge are the focus of this work. Time-dependent transport simulations indicate that, with a trade-off of the EC equatorial and upper launcher, the formation and sustainment of quasi-steady state ITBs could be demonstrated in ITER with the baseline heating configuration. However, with proper constraints from peeling-ballooning theory on the pedestal width and height, the fusion gain and the maximum non-inductive current are below the ITER target. Upgrades of the heating and current drive system in ITER, like the use of Lower Hybrid current drive, could overcome these limitations, sustaining higher non-inductive current and confinement, more expanded ITBs which are ideal MHD stable.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗