Search NASA⌕ Search

SEARCH · Search NASA

Results for “JET FUEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Applications of endothermic research technology to the high speed civil transport

The success of strategies for controlling emissions and enhancing performance in High Speed Research applications may be increased by more effective utilization of the heat sink afforded by the fuel in the vehicle thermal management system. This study quantifies the potential benefits associated with the use of supercritical preheating and endothermic cracking of jet fuel prior to combustion to enhance the thermal management capabilities of the propulsion systems in the High Speed Civil Transport (HSCT). A fuel-cooled thermal management system, consisting of plate-fin heat exchangers and a small auxiliary compressor, is defined for the HSCT, integrated with the engine, and an assessment of the effect on engine performance, weight, and operating cost is performed. The analysis indicates significant savings due a projected improvement in fuel economy, and the potential for additional benefit if the cycle is modified to take full advantage of all the heat sink available in the fuel.

Glickstein, M. R.↗
DOE OSTI2022

NIR Dataset and Models (Near-Infrared Spectroscopy Calibration Dataset for Butanediol Fermentation and Multivariate Calibration Models) [SWR-22-60]

2,3-butanediol (2,3-BDO) is an economically important platform chemical that can be used in a variety of chemical feedstocks, liquid fuels, and biosynthetic building blocks. While 2,3-BDO can be efficiently produced by fermentation, the fermentation requires continuous monitoring and control to maximize 2,3-BDO yields and minimize inhibitory coproducts. Because of the time required for sampling and at-line measurement of fermentation samples with high pressure liquid chromatography (HPLC), the ability for operators to perform real-time modification to fermentation conditions is limited. To overcome this challenge, researchers from the National Renewable Energy Laboratory (NREL) have developed a calibration model which can predict the concentration of several analytes in real-time using near-infrared (NIR) spectra of the filtered fermentation broth. While significantly reducing the need for off-line sampling, NREL expects this technology to play a critical role in maximizing 2,3-BDO production. 2,3-butanediol (2,3-BDO) is a useful chemical platform that can be used to create a variety of products. For instance, 2,3-BDO can be (1) dehydrated and converted into methyl ethyl ketone, a liquid fuel additive or (2) deoxydehydrated into 1,3-butadiene for synthetic rubber, which can also be oligomerized in high yields to gasoline, diesel, and jet fuel. In order to maximize 2,3-BDO production, frequent measurement of fermentation samples is needed, as small changes in oxygen concentration can drive the fermentation to undesired products. For example, oxygen-deficient conditions result in glycerol production, while excess oxygen concentrations result in acetoin production. This results in the need for measuring dissolved oxygen, glucose, and xylose concentrations in order to optimize the aeration rate of the fermentation. Traditional monitoring methods occurs off-line and can take up to 30 minutes per sample. With multiple fermenters and high-pressure liquid chromatography (HPLC) injectors, resulting in the need for multiple samples, the sampling process can take hours to complete. NREL’s calibration model can predict the glucose, xylose, 2,3-BDO, acetoin, and glycerol concentrations from NIR spectra of filtered fermentation liquor samples. Using a partial least-squares (PLS) calibration model, NREL’s model can monitor the concentration of these analytes during subsequent fermentations at bench- and pilot-scale, demonstrating the utility of NIR spectroscopy combined with chemometrics for real-time, at-line monitoring of 2,3-BDO fermentations.

Wolfrum, Edward↗
DOE OSTI2025

Quantifying health benefits of sustainable aviation fuels: Modeling decreased ultrafine particle emissions and associated impacts on communities near the Seattle-Tacoma International Airport

Exposure to ultrafine particles (UFP, ≤100 nm) is an emerging health concern linked to premature mortality, with jet fuel combustion identified as a significant source of UFPs near airports. Sustainable aviation fuel (SAF) adoption has the potential to reduce aviation-related UFPs and may particularly benefit populations who reside nearby. However, assessing aviation-specific impacts on health remains challenging due to the lack of tools capable of addressing: fine-scale exposure evaluation, novel ambient pollutants, and groups with increased exposure or susceptibility. We develop and apply a method to estimate reductions in mortality associated with aviation-related UFP reductions at the Seattle-Tacoma (SEA-TAC) International Airport under SAF adoption scenarios, with a focus on near-airport communities. Using UFP exposure surfaces generated from AERMOD modeling, flight count data, and UFP measurements, we evaluated UFP reductions under various control scenarios. We estimated mortality reductions by combining this with population data, baseline mortality, and a hazard ratio of 1.012 (95 % confidence interval: 1.010, 1.015) per interquartile range increment of 2723 particles/cm 3 . Our analysis included 412 census tracts representing almost 1.5 million adults. Baseline aviation-related UFP exposures averaged 1145 (SD: 277) particles/cm 3 . The highest baseline concentrations and subsequent reductions under SAF scenarios were near SEA-TAC. Mortality case reductions averaged between 3.1 (95 % range: 2.5–3.7) for a 5 % UFP reduction to 31.0 (24.6–37.4) for a 50 % reduction, with corresponding mortality rate reductions of 0.2 (0.2–0.3) to 2.1 (1.7–2.5) cases per 100,000 people per year. Mortality rate reductions were larger among populations residing closer to SEA-TAC, including those that were Hispanic or Latino, below-poverty, and did not identify as White. Reducing aviation-related UFPs through SAF adoption could lead to lower mortality, particularly in near-airport communities. This reproducible approach can be adapted to other settings to evaluate health benefits from aviation-related UFP reductions.

Aviation-related air pollution↗
NASA NTRS2003

Coherent Anti-Stokes Raman Scattering (CARS) as a Probe for Supersonic Hydrogen-Fuel/Air Mixing

The dual-pump coherent anti-Stokes Raman spectroscopy (CARS) method was used to measure temperature and the absolute mole fractions of N2, O2 and H2 in a supersonic non-reacting fuel-air mixing experiment. Experiments were conducted in NASA Langley Research Center s Direct Connect Supersonic Combustion Test Facility. Under normal operation of this facility, hydrogen and air burn to increase the enthalpy of the test gas and O2 is added to simulate air. This gas is expanded through a Mach 2 nozzle and into a combustor model where fuel is then injected, mixes and burns. In the present experiment the O2 of the test gas is replaced by N2. The lack of oxidizer inhibited combustion of the injected H2 fuel jet allowing the fuel/air mixing process to be studied. CARS measurements were performed 427 mm downstream of the nozzle exit and 260 mm downstream of the fuel injector. Maps were obtained of the mean temperature, as well as the N2, O2 and H2 mean mole fraction fields. A map of mean H2O vapor mole fraction was also inferred from these measurements. Correlations between different measured parameters and their fluctuations are presented. The CARS measurements are compared with a preliminary computational prediction of the flow.

Danehy, P. M.↗
NASA NTRS1978

Impact of broad-specification fuels on future jet aircraft

The effects that broad specification fuels have on airframe and engine components were discussed along with the improvements in component technology required to use broad specification fuels without sacrificing performance, reliability, maintainability, or safety.

Grobman, J. S.↗
NASA NTRS1973

Thermodynamic and transport properties of air and its products of combustion with ASTMA-A-1 fuel and natural gas at 20, 30, and 40 atmospheres

The isentropic exponent, molecular weight, viscosity, specific heat at constant pressure, thermal conductivity, Prandtl number, and enthalpy were calculated for air, the combustion products of ASTM-A-1 jet fuel and air, and the combustion products of natural gas and air. The properties were calculated over a temperature range from 300 to 2800 K in 100 K increments and for pressures of 20, 30 and 40 atmospheres. The data for natural gas and ASTM-A-1 were calculated for fuel-air ratios from zero to stoichiometric in 0.01 increments.

Poferl, D. J.↗
NASA NTRS2010

Comparing Spray Characteristics from Reynolds Averaged Navier-Stokes (RANS) National Combustion Code (NCC) Calculations Against Experimental Data for a Turbulent Reacting Flow

Developing physics-based tools to aid in reducing harmful combustion emissions, like Nitrogen Oxides (NOx), Carbon Monoxide (CO), Unburnt Hydrocarbons (UHC s), and Sulfur Dioxides (SOx), is an important goal of aeronautics research at NASA. As part of that effort, NASA Glenn Research Center is performing a detailed assessment and validation of an in-house combustion CFD code known as the National Combustion Code (NCC) for turbulent reacting flows. To assess the current capabilities of NCC for simulating turbulent reacting flows with liquid jet fuel injection, a set of Single Swirler Lean Direct Injection (LDI) experiments performed at the University of Cincinnati was chosen as an initial validation data set. This Jet-A/air combustion experiment operates at a lean equivalence ratio of 0.75 at atmospheric pressure and has a 4 percent static pressure drop across the swirler. Detailed comparisons of NCC predictions for gas temperature and gaseous emissions (CO and NOx) against this experiment are considered in a previous work. The current paper is focused on detailed comparisons of the spray characteristics (radial profiles of drop size distribution and at several radial rakes) from NCC simulations against the experimental data. Comparisons against experimental data show that the use of the correlation for primary spray break-up implemented by Raju in the NCC produces most realistic results, but this result needs to be improved. Given the single or ten step chemical kinetics models, use of a spray size correlation gives similar, acceptable results

Iannetti, Anthony C.↗
NASA NTRS2012

Life-Cycle Assessments of Selected NASA Ground-Based Test Facilities

In the past two years, two separate facility-specific life cycle assessments (LCAs) have been performed as summer student projects. The first project focused on 13 facilities managed by NASA s Aeronautics Test Program (ATP), an organization responsible for large, high-energy ground test facilities that accomplish the nation s most advanced aerospace research. A facility inventory was created for each facility, and the operational-phase carbon footprint and environmental impact were calculated. The largest impacts stemmed from electricity and natural gas used directly at the facility and to generate support processes such as compressed air and steam. However, in specialized facilities that use unique inputs like R-134a, R-14, jet fuels, or nitrogen gas, these sometimes had a considerable effect on the facility s overall environmental impact. The second LCA project was conducted on the NASA Ames Arc Jet Complex and also involved creating a facility inventory and calculating the carbon footprint and environmental impact. In addition, operational alternatives were analyzed for their effectiveness at reducing impact. Overall, the Arc Jet Complex impact is dominated by the natural-gas fired boiler producing steam on-site, but alternatives were provided that could reduce the impact of the boiler operation, some of which are already being implemented. The data and results provided by these LCA projects are beneficial to both the individual facilities and NASA as a whole; the results have already been used in a proposal to reduce carbon footprint at Ames Research Center. To help future life cycle projects, several lessons learned have been recommended as simple and effective infrastructure improvements to NASA, including better utility metering and data recording and standardization of modeling choices and methods. These studies also increased sensitivity to and appreciation for quantifying the impact of NASA s activities.

Sydnor, George Honeycutt↗
DOE OSTI2025

Analysis of soot formation from aviation fuels in laminar counterflow flames

Combustion emissions from aviation contribute to the formation of condensation trail (contrail) that can lead to the formation of anthropogenic cirrus clouds. Ice particles that form contrails are observed to have a linear correlation with soot particle number density. Synthetic aviation fuels (SAFs) offer a promising route to mitigate the production of soot particles while also increasing energy security. Although studies have focused on combustion and spray behavior, the detailed investigation of soot formation processes for different jet fuels and their impact on models for computational fluid dynamics (CFD) applications is not well understood. Moreover, experimental measurements of soot for canonical flames using Synthetic aviation fuels (SAF) for model validation remain scarce. To address this, we use employed the Lawrence Livermore National Laboratory (LLNL) detailed soot model based on the discrete sectional method. Additionally, we develop two reduced chemical mechanisms for Jet-A and Alcohol-to-Jet (C1) that are suitable for turbulent flame simulations and couple them with the Hybrid Method of Moments (HMOM). The detailed and reduced model frameworks are validated against experimental measurements of soot volume fraction (ƒ ν ) from a counterflow burner experiment previously reported in the literature. Given the good agreement between modeling results and experimental measurements for the (1) spatial distribution of ƒ ν and (2) the non-linear variation of peak ƒ ν with strain rate, we further investigate the modeled sub-processes (nucleation, condensation, surface growth, and oxidation) using the LLNL model to analyze the assumptions in the reduced model framework. Furthermore, the results indicate a significant contribution from resonant radicals to the surface growth of soot particles, which are not accounted for in the current implementation of HMOM and could help reconcile soot predictions by the reduced model with observations.

Counterflow↗
NASA NTRS2004

Fuel-Flexible Gas Turbine Combustor Flametube Facility

Facility modifications have been completed to an existing combustor flametube facility to enable testing with gaseous hydrogen propellants at the NASA Glenn Research Center. The purpose of the facility is to test a variety of fuel nozzle and flameholder hardware configurations for use in aircraft combustors. Facility capabilities have been expanded to include testing with gaseous hydrogen, along with the existing hydrocarbon-based jet fuel. Modifications have also been made to the facility air supply to provide heated air up to 350 psig, 1100 F, and 3.0 lbm/s. The facility can accommodate a wide variety of flametube and fuel nozzle configurations. Emissions and performance data are obtained via a variety of gas sample probe configurations and emissions measurement equipment.

Little, James E.↗
NASA NTRS1974

Bibliography on aircraft fire hazards and safety. Volume 1: Hazards. Part 1: Key numbers 1 to 817

Ignition temperatures of n-hexane, n-octane, n-decane, JP-6 jet fuel, and aircraft engine oil MIL-7-7808 (0-60-18) were determined in air using heated Pyrex cylinders and Nichrome wires, rods, or tubes. Ignition temperature varied little with fuel-air ratio, but increased as the size of the heat source was decreased. Expressions are given which define the variation of the hot surface ignition temperatures of these combustibles with the radius and the surface area of the heat source. The expressions are applicable to stagnant or low velocity flow conditions (less than 0.2 in./sec.). In addition, the hot gas ignition temperatures of the combustible vapor-air mixtures were determined with jets of hot air. These ignition temperatures also varied little with fuel-air ratio and increased as the diameter of the heat sources was decreased.

Pelouch, J. J., Jr.↗
NASA NTRS1978

Characteristics and combustion of future hydrocarbon fuels

Dwindling supply of high-quality crude is beginning to manifest itself in the form of crude oils containing higher percentages of aromatic compounds, sulfur, nitrogen, and trace constituents. In the present paper, problems which have arisen with regard to the hydrogen content in jet fuels derived from these crude oil sources are discussed, with particular reference to the effects of varying the fuel properties on the combustion and thermal stability characteristics of a fuel. The importance of knowing how severe the effects of variations in hydrogen content, fuel-bound-nitrogen content, and boiling range are on such combustion phenomena as soot and carbon formation, emissions, and ignition is pointed out.

Rudey, R. A.↗
NASA NTRS1927

High-speed Oil Engines for Vehicles. Part II

Further progress toward the satisfactory solution of the difficult problem of the distribution and atomization of the injected fuel was made by extensive experimentation with various fuel valves, nozzles, and atomizing devices. Valuable information was also obtained through numerous experimental researches on the combustion of oils and the manner of introducing the combustion air into the cylinder, as well as on the physical processes of atomization, the determination of the size of drops, etc. These researches led to the conclusion that it is possible, even without producing great turbulence in the combustion chamber and at moderate pump pressure, if the degree of atomization and the penetrative power of the fuel jet are adapted to the shape of the combustion chamber and to the dimensions of the cylinder.

ENGINES, OIL↗
DOE OSTI2024

High Performance Metal-Supported SOFC System for Range Extension of Commercial Aviation

The DOE ARPA-E REEACH program [1] has enabled this Phase 1 study that conceptualizes a commercial 154 passenger electric aircraft using renewable aviation fuel for range extension while meeting similar mission performance levels as current commercial aircraft. Commercial aviation accounts for about 2.5% of global CO2 emissions, and close to 5% of overall anthropogenic climate change due to the added accounting of contrail’s effects [2]. The sector has adopted a goal of carbon neutrality by 2050 [3]. 110 nations, and recently the new US administration, have embarked on work to address this important challenge. The US DOE has released a roadmap to enable the further development of sustainable aviation fuel (SAF) in the hopes that it could meet all of aviation’s fuel needs by 2050 [4]. However, SAF fuel price and sufficient future feedstock availability remains a concern [5]. Considering the first commercial biofuel flight demonstration 14 years ago [6] and that SAF still only comprises less than 0.1% of jet fuel use, the question arises as how it can ramp up to 100% use in the next 27 years. One option that has the potential to substantially reduce the need for SAF is to implement light-weight Solid Oxide Fuel Cells (SOFCs) that can efficiently utilize SAF or other sulfur-free hydrocarbon fuels. As opposed to lower temperature PEM (Proton Exchange Membrane) fuel cells that can use high-purity hydrogen, SOFC’s fuels are very flexible, ranging from low cost liquefied natural gas (LNG), renewable liquefied natural gas (RLNG), to SAF, to generate clean electrical power for use in aviation propulsion and auxiliary power units [7] [8]. Research progress is needed to enable SOFCs to achieve 3.0 kW/kg power density, making them viable for aviation [9]. The DOE’s Advanced Research Projects Agency – Energy (ARPA-E) has therefore initiated an aviation SOFC R&D program that is anticipated to dramatically reduce aircraft fuel use though the implementation of “Range Extenders for Electric Aviation with low Carbon and High efficiency” (REEACH) [1] for medium range commercial aircraft. This report summarizes the progress during phase 1 of the REEACH program.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS2000

Ensemble Diffraction Measurements of Spray Combustion in a Novel Vitiated Coflow Turbulent Jet Flame Burner

An experimental investigation is presented of a novel vitiated coflow spray flame burner. The vitiated coflow emulates the recirculation region of most combustors, such as gas turbines or furnaces; additionally, since the vitiated gases are coflowing, the burner allows exploration of the chemistry of recirculation without the corresponding fluid mechanics of recirculation. As such, this burner allows for chemical kinetic model development without obscurations caused by fluid mechanics. The burner consists of a central fuel jet (droplet or gaseous) surrounded by the oxygen rich combustion products of a lean premixed flame that is stabilized on a perforated, brass plate. The design presented allows for the reacting coflow to span a large range of temperatures and oxygen concentrations. Several experiments measuring the relationships between mixture stoichiometry and flame temperature are used to map out the operating ranges of the coflow burner. These include temperatures as low 300 C to stoichiometric and oxygen concentrations from 18 percent to zero. This is achieved by stabilizing hydrogen-air premixed flames on a perforated plate. Furthermore, all of the CO2 generated is from the jet combustion. Thus, a probe sample of NO(sub X) and CO2 yields uniquely an emission index, as is commonly done in gas turbine engine exhaust research. The ability to adjust the oxygen content of the coflow allows us to steadily increase the coflow temperature surrounding the jet. At some temperature, the jet ignites far downstream from the injector tube. Further increases in the coflow temperature results in autoignition occurring closer to the nozzle. Examples are given of methane jetting into a coflow that is lean, stoichiometric, and even rich. Furthermore, an air jet with a rich coflow produced a normal looking flame that is actually 'inverted' (air on the inside, surrounded by fuel). In the special case of spray injection, we demonstrate the efficacy of this novel burner with a methanol spray in a vitiated coflow. As a proof of concept, an ensemble light diffraction (ELD) optical instrument was used to conduct preliminary measurements of droplet size distribution and liquid volume fraction.

Cabra, R.↗
DOE OSTI2021

Process Intensification for the Biological Production of the Fuel Precursor Butyric Acid from Biomass

The production of fuels from lignocellulosic biomass is key to reduce our reliance on petroleum and to promote a sustainable bioeconomy. Butyric acid (BA) is a promising chemical precursor for the production of renewable diesel and jet fuels. BA can be biologically produced from lignocellulosic sugars. However, challenges associated with product selectivity and recovery must be overcome to achieve industrially relevant metrics. Here, we evaluate various fermentation configurations and demonstrate near-homo-butyrate production by using the biocatalyst Clostridium tyrobutyricum. We also develop an advanced in situ product recovery process based on hybrid extraction-distillation (HED-ISPR) and conduct techno-economic analyses and life cycle assessments. We demonstrate that the HED-ISPR process lowers the overall capital and operating expenses and environmental impact compared to other traditional fermentation processes. Overall, BA minimum product selling price from biomass is 55% of the current BA selling price from petroleum, a significant decrease toward viable renewable fuel production.

09 BIOMASS FUELS↗
NASA NTRS2000

Buoyancy Effects on Flow Transition in Hydrogen Gas Jet Diffusion Flames

Experiments were performed in earth-gravity to determine how buoyancy affected transition from laminar to turbulent flow in hydrogen gas jet diffusion flames. The jet exit Froude number characterizing buoyancy in the flame was varied from 1.65 x 10(exp 5) to 1.14 x 10(exp 8) by varying the operating pressure and/or burner inside diameter. Laminar fuel jet was discharged vertically into ambient air flowing through a combustion chamber. Flame characteristics were observed using rainbow schlieren deflectometry, a line-of-site optical diagnostic technique. Results show that the breakpoint length for a given jet exit Reynolds number increased with increasing Froude number. Data suggest that buoyant transitional flames might become laminar in the absence of gravity. The schlieren technique was shown as effective in quantifying the flame characteristics.

Albers, Burt W.↗
NASA NTRS2004

Structure of Propagating and Attached Hydrocarbon Flames

Direct numerical simulations with C3-chemistry and radiative heat-loss models have been performed to reveal the internal structure of propagating and attached flames in an axisymmetric fuel jet of methane, ethane, ethylene, acetylene, or propane in air under normal and zero gravity. Observations of the flames were also made at the NASA Glenn 2.2-Second Drop Tower. In computations, the fuel issued into quasi-quiescent air for a fixed mixing time before it was ignited along the centerline at stoichiometry. The edge of the flame propagated through a flammable layer at the laminar flame speed of the stoichiometric fuel-air mixture independent of gravity. For all cases, a peak reactivity spot, i.e., reaction kernel, was formed in the flame base, thereby holding a trailing diffusion flame. The location of the reaction kernel in the attached flames depended inversely on the reactivity. The reaction-kernel correlations between the reactivity and the velocity were developed further using variables related to local Damkahler and Peclet numbers.

Takahashi, Fumiaki↗