Search NASA⌕ Search

SEARCH · Search NASA

Results for “LIGNITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

A deep insight on the coal ash-to-slag transformation behavior during the entrained flow gasification process

Recent research provided deep insight on the coal ash-to-slag transformation characterization during the entrained flow gasification process, with experimentation on a 40 kg/hr (dry basis) coal-fed opposed multi-burner (OMB) entrained flow gasifier and simulation via FactSage™ software. A general mechanism is presented to relate the gasifier design temperature, ash fluid temperature, and operating temperature with the degree of the slag polymerization. The change of the high temperature zone, the corresponding particle residence time in the high temperature zone, and syngas composition have obvious effects on the slag mineral transformation behavior. Mineral types formed on the wall of the gasifier chamber were mainly anorthite (CaAl 2 Si 2 O 8 ), aluminum oxide (Al 2 O 3 ), and calcium sulfide (CaS). These minerals transformed to anorthite and diopside (CaMgSi 2 O 6 ) at the slag hole zone, while the minerals at the lock hopper were anorthite, orthoclase (KAlSi 3 O 8 ), quartz (SiO 2 ), gypsum (CaSO 4 ), calcite (CaCO 3 ), and halite (NaCl). FactSage™ predicted minerals as anorthite, diopside, orthoclase, and albite (NaAlSi 3 O 8 ), etc., where the slag temperature was below the ash fluid temperature and when the ratios of CO/CO 2 and (CO + H 2 )/CO 2 were lower than 1.0 and 2.0, respectively. By simulation, residual carbon was found to be the dominant factor over syngas composition to cause mineral transformation, and this was verified experimentally. The Ca-based crystals, typically anorthite, was shifted to diopside, near the slag hole zone, and a linear relationship was found between the content ratios of diopside/(anorthite + diopside), CaO/SiO 2 , and (CaO + MgO)/SiO 2 . A dimensionless number, θ, was defined to characterize the changing chemical composition and the degree of slag polymerization, with temperature deviation from the design condition. Three zones of θ were identified and related to the deviation between the actual gasification condition from the design condition. Finally, a low slag polymerization degree corresponded with a higher temperature deviation between the actual condition and design condition, and this proved that increased residual carbon content and changing iron valence state increased the mineral types when the slag temperature was below the ash fluid temperature.

01 COAL, LIGNITE, AND PEAT↗

Distribution of rare earth elements in fly ash derived from the combustion of Illinois Basin coals

This study examined rare earth element (REE) trends for Illinois Basin coal-sourced fly ashes, with the goal of understanding the elemental composition and resource potential for various fly ash fractions. Illinois Basin coals have a high volatile C through A bituminous rank with a moderate ash content (slightly>12% ash (dry basis)), about 3% sulfur, and, in general, lower concentrations of hazardous and other trace elements than many Central Appalachian coals. Fly ash from the combustion of Illinois Basin coals tends to have a high Fe 2 O 3 content owing to the amount of pyrite in the feed coals. The rare earth element (REE) concentrations in Illinois Basin coal-sourced fly ashes are less than that for fly ashes from the combustion of Central Appalachian coals. The Upper continental crust-corrected fly ashes show an H-type enrichment, a positive Eu N /Eu N * , and, in some cases, a sharp Gd peak. For comparison, a suite of fly ashes from the combustion of a blend of eastern Kentucky coals had an H-type enrichment, a positive Eu N /Eu N * , but only a minimal Gd peak. In contrast, fly ash from the combustion of the Fire Clay coal, a REE-rich coal, had a negative Eu N /Eu N * and a sharp Gd peak. Finally, these results highlight the importance of feed coal composition on trace element contents of respective combustion fly ash fractions and also the unique REE enrichment patterns of the Illinois Basin fly ashes relative to the better studied fly ashes of eastern Kentucky and Central Appalachia.

01 COAL, LIGNITE, AND PEAT↗

Geomechanical and flow implications with continued bioconversion of coal to methane: Experiments and modeling

Microbial conversion of coal to methane is a promising technology during transition of coal-based energy from conventional coal mining to natural gas recovery from coal. Significant research advances have been made towards engineering ideal microbial communities and nutrients for bio-stimulation of coal. However, actual field applications require geomechanical and flow behavior characterization of coal during the bioconversion process as well as gas production over the life of the created “biogenic gas reservoirs”. This work presents the results of an experimental investigation to estimate gas/methane production using bioconversion of coal and analyses of variations in bulk modulus, strain and permeability. Bulk modulus of coal demonstrated time-dependent behavior with continued bioconversion of solid coal. The phenomenon was modeled using mass balancing in a closed environment and the logistic equation based biogenic gas production with time. The modeled gas production and changes in modulus of coal showed excellent agreement with the corresponding experimental results. Next, numerical simulation of biogenic conversion of coal in a constant stress in-situ condition, replicating the Huff ‘n Puff method under field conditions, was carried out. The results showed that bioconversion can lead to decrease in effective stress, increase in permeability and decrease in the modulus of coal with time. Repeated recharge of coal with nutrients and recovering the produced gas, that is, sequential cycles of Huff n’ Puff, showed further increase in permeability and decrease in coal strength, potentially leading to coal failure in-situ, further increasing the permeability, thus enhancing the prospect of field application of the technology.

01 COAL, LIGNITE, AND PEAT↗

Distribution of rare earth elements in the pilot-scale processing of fly ashes derived from eastern Kentucky coals: Comparisons of the feed and processed ashes

Beneficiated fly ash from the combustion of Central Appalachian high volatile bituminous coals was extracted with HNO 3 in a pilot-scale processing plant. Several major oxides (notably CaO and SO 3 , but also including Fe 2 O 3 , MgO, K 2 O, and P 2 O 5 ) and minor elements (Mn, As, Sr, Ba, and Pb) are depleted in the post-HNO 3 -extraction spent ash. The total lanthanides, Y, and Sc concentration is reduced by about 20% in the spent ash, with Gd showing the greatest decrease. Along with Gd, Nd and Dy are also well differentiated between the feed and spent ashes, with La and Sm showing minimal partitioning. The Gd decrease is correlated with the depletion of Fe 2 O 3 . The heavy rare earth elements (REE heavier than Eu) and Y are disproportionately concentrated in the HNO 3 -leachate compared to the light REE. For the ashes studied, Sc did not partition between the feed and spent ashes. Pozzolanicity tests show that the compressive strength and strength activity indices of the spent ash + ordinary Portland cement (OPC) mixes are comparable to 100% OPC, indicating that the spent ashes produced in the pilot-scale runs have the potential to be sold as a Class F fly ash. Finally, the beneficiated ash chemistry influences the chemistry of the post-HNO 3 -extraction spent ash and the HNO 3 -leachate. A 500-ppm-REE fly ash will presumably be a more economically favorable feedstock than an ash with a significantly lesser concentration.

01 COAL, LIGNITE, AND PEAT↗

Signatures of rare earth element distributions in fly ash derived from the combustion of Central Appalachian, Illinois, and Powder River basin coals

We report the distribution of Rare Earth elements (REE) in coal-derived fly ashes can have distinctive patterns when fly ashes are produced from different coals within or between basins, such as the Pennsylvanian Class F fly ashes from the Illinois and Central Appalachian basins. Both the Fire Clay coal and a blend of a number of eastern Kentucky coals show strong Gd peaks and an H-type distribution in the Upper Continental Crust-corrected plots. The Fire Clay coal-derived ash has a higher heavy REE concentration than the blended coal-derived ash. The Illinois Basin-derived fly as has an overall lower REE concentration than the latter ashes. Class C fly ash derived from Powder River Basin coals has, with the exception of an Eu peak, a flatter distribution of REE and an overall L-type or indistinct H- versus L-type distribution. The signatures of the REE in fly ashes may be useful in predicting their behavior in the extraction of the REE; simple extrapolations from the basic concentrations and the predicted extraction percentages for ashes from different basins are not necessarily indicative of the actual distribution of the extracted REE.

01 COAL, LIGNITE, AND PEAT↗

Numerical analysis of particle dispersion and deposition in coal combustion using large-eddy simulation

High-fidelity modeling provides a useful approach to investigate the particle dispersion and deposition mechanism in pulverized coal combustion. To be able to analyze these detailed mechanisms, this work couples detailed multiphysics models for poly-dispersed turbulent, particle-laden flow, particle and gas phase reaction chemistry, convective, conductive and radiative heat transfer, ash formation and deposition with a Large-Eddy Simulation (LES) approach to numerically simulate coal combustion in a downfired self-sustained oxy-fuel combustor (OFC). It is necessary to explicitly capture all but the highest frequency dynamics of the turbulence and its coupling with each of the other physical phenomena using LES. Effects of subgrid-scale unresolved turbulence on the particle motions are also analyzed by a novel Stokes number analysis. Due to the inherent relation ship between coal combustion and ash deposition, this study integrates the improved ash deposition model into the numerical simulation. Overall simulation results are compared with experimentally measured data from the OFC. The simulation and measured data for the averaged gas temperature and deposition rates agree with 5% and 28%. This study shows that high-fidelity LES coupled with other detailed multiphysics models running on a exascale computing facility can provide a good representation of complex coal combustion and deposition in a laboratory-scale furnace.

multiphysics model↗

Microstructural diversity and digestion yields of select bituminous and subbituminous coals as raw material candidates for carbon fiber precursor production

Here, this work investigates the use of coals as raw materials for carbon fiber precursor production as a new alternative to coal utilization. Coal being a highly complex and heterogeneous material with different macerals and minerals complicates this task. Extensive microstructural characterization as well as preliminary digestion studies are performed on three bituminous coals (Herrin and Springfield from the Illinois Basin and the Blue Gem from the Central Appalachians) and one subbituminous coal from the Powder River Basin (Monarch), as raw material candidates. The subbituminous coal was richer in oxygen, lower in sulfur, and had a higher volatile matter yield. Microstructural investigations were performed using X-ray diffraction, X-ray/neutron computed tomography, scanning electron microscopy with energy dispersive spectroscopy, and petrology. Mild solvent extraction studies were conducted using creosote and decant oil as solvents in microreactors. The extraction yield was sensitive to temperature and time (350 to 450 °C between 30 and 120 mins.) for both creosote and decant oil digestions. While the Blue Gem coal had more desirable microstructural properties with less mineral content and cleaner macerals, it had the lowest coal conversion to quinoline soluble ‘liquid’ (of the bituminous coals). The lower coal conversion yield was hypothesized to be connected to the lack of FeS2 which could act as a catalyst when Fe is liberated from the structure under solvent extraction conditions. The Herrin and Springfield coals revealed similar microstructures and coal conversion efficiencies (higher than Blue Gem). These coals were the most promising candidates for further examination from this first approximations study. The subbituminous Monarch coal, however, was deemed less suitable due to poor coal conversion and less desirable microstructures. Additionally, the presented results with combined microstructural data from multiple length scales established a framework necessary for a first approximations study in this new coal utilization approach.

01 COAL, LIGNITE, AND PEAT↗

Hydrogen-rich syngas production from the steam co-gasification of low-density polyethylene and coal refuse

Gasification provides a promising pathway for transforming waste materials into valuable products, such as fuels and chemicals. Here, this study investigates the steam co-gasification of low-density polyethylene (LDPE) and compressed thickener underflow, representative of coal refuse (CR), in a drop tube reactor. The effects of feed blend ratio (0–100 wt% LDPE) and temperature (800–1000 °C) on syngas composition, tar formation, and process efficiency are examined. The high volatility of LDPE makes it more reactive than CR but also promotes the formation of 2–7 ring aromatic tars. Increasing temperature improves carbon conversion efficiency (CCE), cold gas efficiency (CGE), and syngas yield, although the lower heating value (LHV) of syngas decreases. Hydrogen is the dominant gas product, reaching 59 vol% with the H 2 /CO molar ratio ranging from 2.27 to 4.74. Synergistic effects from alkali and alkali earth metals (AAEMs), particularly K and Ca, in CR ash enhance syngas yield by catalyzing char gasification and tar cracking. Hematite (Fe 2 O 3 ) and ash from sub-bituminous/bituminous coals are explored as tar reforming catalysts. Fe 2 O 3 achieves 100 % tar reforming efficiency, while coal ash, with a lower Fe 2 O 3 content (15 wt%), is less effective at cracking polycyclic aromatic hydrocarbons, particularly naphthalene. These findings demonstrate the flexibility of co-gasification, allowing precise tuning of syngas characteristics for specific downstream applications. Further optimization of waste-derived catalysts could enhance the economic viability of gasification in waste-to-energy processes.

01 COAL, LIGNITE, AND PEAT↗

The effect of oxygen-to-fuel stoichiometry on coal ash fine-fragmentation mode formation mechanisms.

Ash particles smaller than 2.5 {micro}m in diameter generated during pulverized coal combustion are difficult to capture and may pose greater harm to the environment and human health than the discharge of larger particles. Recent research efforts on coal ash formation have revealed a middle fine-fragment mode centered around 2 {micro}m. Formation of this middle or fine-fragment mode (FFM) is less well understood compared to larger coarse and smaller ultrafine ash. This study is part of an overall effort aimed at determining the key factors that impact the formation of FFM. This work examined the effects of oxygen-to-fuel stoichiometry (OFS). Pulverized Illinois No.6 bituminous coal was combusted and the ash generated was size segregated in a Dekati low pressure inertial impactor. The mass of each fraction was measured and the ash was analyzed using scanning electron microscopy (SEM) and X-ray microanalysis. The FFM ash types were classified based on the SEM images to evaluate the significant fine-fragment ash formation mechanisms and determine any possible link between stoichiometry and formation mechanism. From the particle size distributions (PSDs), the coarse mode appears unaffected by the change in OFS, however, the OFS 1.05 lowered the fraction of ultrafine ash in relation to the higher OFS settings, and appears to increase the portion of the FFM. An intermediate minimum was found in the FFM at 1.3 {micro}m for the 1.20 and 1.35 OFS tests but was not observed in the 1.05 OFS. SEM analysis also suggests that OFS may contribute to changing formation mechanisms.

01 COAL, LIGNITE, AND PEAT↗

Correlation between the critical viscosity and ash fusion temperatures of coal gasifier ashes

Coal gasification yields synthesis gas, an important intermediate in chemical manufacturing. It is also vital to the production of liquid fuels through the Fischer-Tropsch process and electricity in Integrated Gasification Combined Cycle power generation. Minerals naturally present in coal become molten in entrained-flow slagging gasifiers. Molten coal ash slag penetrates and dissolves refractory bricks, leading to costly plant shutdowns. The extent of coal ash slag penetration and refractory brick dissolution depends on the slag viscosity, the gasification temperature, and the composition of slag and bricks. We measured the viscosity of several synthetic coal ash slags with a high-temperature rotary viscometer and their ash fusion temperatures through optical image analysis. All measurements were made in a carbon monoxide-carbon dioxide reducing atmosphere that approximates coal gasification conditions. Empirical correlation models based on ash fusion temperatures were used to calculate critical viscosity temperatures based on the coal ash compositions. These values were then compared with those obtained from thermodynamic phase-transition models. An understanding of slag viscosity as a function of ash composition is important to reducing refractory wear in slagging coal gasifiers, which would help to reduce the cost and environmental impact of coal for chemical and electricity production.

01 COAL, LIGNITE, AND PEAT↗

CFD-aided benchmark assessment of coal devolatilization one-step models in oxy-coal combustion conditions

Coal devolatilization, as first step in thermochemical processes involving solid fuels, has been targeted in plenty of CFD investigations: despite the variety of models that were developed to define the rate of the process and the amount of volatile matter released, not all of them are suitable for CFD simulations of large-scale coal combustors. Empirical models ensure both simplicity and feasibility, but not full reliability for all coal types and operating conditions. CFD modeling results for coal conversion during devolatilization in an entrained flow reactor and oxy-conditions are presented and compared to experimental data. A benchmark assessment of one-step models on the accuracy of the volatile yield prediction is then performed. It is shown that the heating rate strongly influences the devolatilization process and its modeling, not only in terms of rate but also in terms of yield, which differs significantly from the proximate analysis value. Furthermore, this indicates the need for a model able to predict the variation of coal volatile yield with temperature and heating rate, in addition to the kinetic model.

01 COAL, LIGNITE, AND PEAT↗

Collaborative simulations and experiments for a novel yield model of coal devolatilization in oxy-coal combustion conditions

Oxy-coal combustion is an emerging low-cost “clean coal” technology for emissions reduction and Carbon Capture and Sequestration (CCS). The use of Computational Fluid Dynamics (CFD) tools is crucial for the development of cost-effective oxy-fuel technologies and the minimization of environmental concerns at industrial scale. The coupling of detailed chemistry models and CFD simulations is still challenging, especially for large-scale plants, because of the high computational efforts required. The development of scale-bridging models is therefore necessary, to find a good compromise between computational efforts and the physical-chemical modeling precision. This paper presents a procedure for scale-bridging modeling of coal devolatilization, in the presence of experimental error, that puts emphasis on the thermodynamic aspect of devolatilization, namely the final volatile yield of coal, rather than kinetics. The procedure consists of an engineering approach based on dataset consistency and Bayesian methodology including Gaussian-Process Regression (GPR). Experimental data from devolatilization tests carried out in an oxy-coal entrained flow reactor were considered and CFD simulations of the reactor were performed. Jointly evaluating experiments and simulations, a novel yield model was validated against the data via consistency analysis. In parallel, a Gaussian-Process Regression was performed, to improve the understanding of the uncertainty associated to the devolatilization, based on the experimental measurements. Potential model forms that could predict yield during devolatilization were obtained. The set of model forms obtained via GPR includes the yield model that was proven to be consistent with the data. Finally, the overall procedure has resulted in a novel yield model for coal devolatilization and in a valuable evaluation of uncertainty in the data, in the model form, and in the model parameters.

01 COAL, LIGNITE, AND PEAT↗

Waste to worth: A high-temperature water-gas shift magnetite catalyst with encapsulated core-shell structure from coal fly ash

In this paper, we demonstrate the synthesis of magnetite-based, encapsulated catalyst with a core-shell structure from coal fly ash, an industrial solid waste, and its application to industrially important high temperature water-gas shift reaction (HT-WGSR). The catalyst precursor was first synthesized through a leaching-precipitation-hydrothermal process, leading to the formation of a nanosheet-like hematite precursor consisting of Fe 3+ as primary element and minor cations including Al 3+ , Mg 2+ and other cations (e.g. Ca 2+ and Ti 4+ ). During the WGSR, the nanosheets broke into smaller particles with a core of magnetite with a diameter of ~20 nm, whereas the inherent impurity elements were activated and migrated to the outer surface forming a shell with a thickness of ~4 nm. Due to the protection of shell, the as-synthesized catalyst exhibited improved activity, thermal stability and long-term durability for HT-WGSR at 400 °C and 450 °C. Compared to the pure hematite, this catalyst exhibited much higher activity and stability, i.e., increased CO conversion and decreased deactivation rate constant, by a factor of four and three, respectively. Additionally, through a bottom-up reverse synthesis, we have confirmed that Al 3+ functioned as a textual promoter enhancing the interfacial area of the catalyst. On the other hand, the presence of minor impurity elements, in particular 2.58 wt% Mg 2+ and 0.18 wt% Ti 4+ , were found to increase the basicity, and promote the adsorption rate of CO, the redox of catalysts, and the alteration of the reaction mechanism from regenerative to associative with the formation of a strong intermediate formate. Finally, this study not only opens a new direction on the valorization of solid waste into high-value catalysts, promoting the sustainability of solid waste management, but also provides an alternative, cost-effective and scalable approach for the design and fine-tuning of encapsulated catalysts.

01 COAL, LIGNITE, AND PEAT↗

Separation of thorium, uranium, and rare earths from a strip solution generated from coarse coal refuse

This work systematically evaluated the separation performance of thorium, uranium, and rare earths when coal and coal byproduct were utilized as a non-traditional feedstock for rare earth production. A synthetic solution was prepared following the elemental composition of a strip solution generated from coarse coal refuse and used throughout the study. Various separation techniques including selective precipitation, solvent extraction, and a modified experimental protocol incorporating the two were applied to extract rare earths while minimizing the non-selective recovery of thorium and uranium into the product stream. Test results indicate that selective precipitation was effective for the removal of thorium at a pH value approaching 5 while solvent extraction preferentially removed uranium from rare earths. Therefore, a modified experimental protocol consisting of both selective precipitation and solvent extraction was subsequently developed and implemented. The findings following the modified experimental protocol indicate that extractant concentration, solvent extraction feed pH, and organic to aqueous (O/A) ratio all played a significant role in the removal of uranium. Among all the tests conducted, the best separation performance was achieved using a one-stage precipitation at a pH value of 4.8, 50 v% TBP, solvent extraction feed pH of 3.5, and an O/A ratio of 3, which corresponded to an overall rare earth, thorium, and uranium recovery of 79.6%, 0%, and 3.1%, respectively.

01 COAL, LIGNITE, AND PEAT↗

The Potential for Increased Atmospheric CO2 Emissions and Accelerated Consumption of Deep Geologic CO2 Storage Resources Resulting from the Large-Scale Deployment of a CCS-Enabled Unconventional Fossil Fuels Industry in the U.S.

Desires to enhance the energy security of the United States have spurred significant interest in the development of abundant domestic heavy hydrocarbon resources including oil shale and coal to produce unconventional liquid fuels to supplement conventional oil supplies. However, the production processes for these unconventional fossil fuels create large quantities of carbon dioxide (CO2) and this remains one of the key arguments against such development. Carbon dioxide capture and storage (CCS) technologies could reduce these emissions and preliminary analysis of regional CO2 storage capacity in locations where such facilities might be sited within the U.S. indicates that there appears to be sufficient storage capacity, primarily in deep saline formations, to accommodate the CO2 from these industries. Nevertheless, even assuming wide-scale availability of cost-effective CO2 capture and geologic storage resources, the emergence of a domestic U.S. oil shale or coal-to-liquids (CTL) industry would be responsible for significant increases in CO2 emissions to the atmosphere. The authors present modeling results of two future hypothetical climate policy scenarios that indicate that the oil shale production facilities required to produce 3MMB/d from the Eocene Green River Formation of the western U.S. using an in situ retorting process would result in net emissions to the atmosphere of between 3000-7000 MtCO2, in addition to storing potentially 900-5000 MtCO2 in regional deep geologic formations via CCS in the period up to 2050. A similarly sized, but geographically more dispersed domestic CTL industry could result in 4000-5000 MtCO2 emitted to the atmosphere in addition to potentially 21,000-22,000 MtCO2 stored in regional deep geologic formations over the same period. While this analysis shows that there is likely adequate CO2 storage capacity in the regions where these technologies are likely to deploy, the reliance by these industries on large-scale CCS could result in an accelerated rate of utilization of the nation’s CO2 storage resource, leaving less high-quality storage capacity for other carbon-producing industries including electric power generation.

01 COAL, LIGNITE, AND PEAT↗

The Impact of Electric Passenger Transport Technology under an Economy-Wide Climate Policy in the United States: Carbon Dioxide Emissions, Coal Use, and Carbon Dioxide Capture and Storage

Plug-in hybrid electric vehicles (PHEVs) have the potential to be an economic means of reducing direct (or tailpipe) carbon dioxide (CO2) emissions from the transportation sector. However, without a climate policy that places a limit on CO2 emissions from the electric generation sector, the net impact of widespread deployment of PHEVs on overall U.S. CO2 emissions is not as clear. A comprehensive analysis must consider jointly the transportation and electricity sectors, along with feedbacks to the rest of the energy system. In this paper, we use the Pacific Northwest National Laboratory’s MiniCAM model to perform an integrated economic analysis of the penetration of PHEVs and the resulting impact on total U.S. CO2 emissions.

01 COAL, LIGNITE, AND PEAT↗

Large-Scale Utilization of Biomass Energy and Carbon Dioxide Capture and Storage in the Transport and Electricity Sectors under Stringent CO2 Concentration Limit Scenarios

This paper examines the potential role of large scale, dedicated commercial biomass energy systems under global climate policies designed to meet atmospheric concentrations of CO2 at 400ppm and 450ppm by the end of the century. We use an integrated assessment model of energy and agriculture systems to show that, given a climate policy in which terrestrial carbon is appropriately valued equally with carbon emitted from the energy system, biomass energy has the potential to be a major component of achieving these low concentration targets. A key aspect of the research presented here is that the costs of processing and transporting biomass energy at much larger scales than current experience are explicitly incorporated into the modeling. From the scenario results, 120-160 EJ/year of biomass energy is produced globally by midcentury and 200-250 EJ/year by the end of this century. In the first half of the century, much of this biomass is from agricultural and forest residues, but after 2050 dedicated cellulosic biomass crops become the majority source, along with growing utilization of waste-to-energy. The ability to draw on a diverse set of biomass based feedstocks helps to reduce the pressure for drastic large-scale changes in land use and the attendant environmental, ecological, and economic consequences those changes would unleash. In terms of the conversion of bioenergy feedstocks into value added energy, this paper demonstrates that biomass is and will continue to be used to generate electricity as well as liquid transportation fuels. A particular focus of this paper is to show how climate policies and technology assumptions - especially the availability of carbon dioxide capture and storage (CCS) technologies - affect the decisions made about where the biomass is used in the energy system. The potential for net-negative electric sector emissions through the use of CCS with biomass feedstocks provides an attractive part of the solution for meeting stringent emissions constraints; we find that at carbon prices above 150$/tCO2, over 90% of biomass in the energy system is used in combination with CCS. Despite the higher technology costs of CCS, it is a very important tool in controlling the cost of meeting a target, offsetting the venting of CO2 from sectors of the energy system that may be more expensive to mitigate, such as oil use in transportation. CCS is also used heavily with other fuels such as coal and natural gas, and by 2095 a total of 1530 GtCO2 has been stored in deep geologic reservoirs. The paper also discusses the role of cellulosic ethanol and Fischer-Tropsch biomass derived transportation fuels as two representative conversion processes and shows that both technologies may be important contributors to liquid fuels production, with unique costs and emissions characteristics.

01 COAL, LIGNITE, AND PEAT↗

A $70/tCO2 greenhouse gas mitigation backstop for China’s industrial and electric power sectors: insights from a comprehensive CCS cost curve

As one of the world's fastest growing economies with abundant coal reserves, China's carbon dioxide (CO2) emissions have doubled in the last decade and are expected to continue growing for the foreseeable future. While the Central Government has been promoting development and growth of cleaner and more efficient energy systems, efforts to reduce carbon emissions from the heavily coal-based economy may require continued and increased development and deployment of carbon dioxide capture and storage (CCS) technologies. This paper presents the first detailed, national-scale assessment of CCS potential across the diverse geographic, geologic, and industrial landscape of China, through the lens of an integrated CCS cost curve. It summarizes the development of a cost curve representing the full chain of components necessary for the capture and geologic storage of CO2 from China's power generation and industrial sectors. Individual component cost estimates are described, along with the optimized source-sink matching of over 1,600 large stationary CO2 sources and 2300 gigatons of CO2 storage capacity within 90 major deep geologic onshore sedimentary sub-basins, to develop a cost curve incorporating CO2 capture, compression, transport, and storage. Results suggest that CCS can provide an important greenhouse gas mitigation option for most regions and industrial sectors in China, able to store more than 80% of emissions from these large CO2 sources (2900 million tons of CO2 annually) at costs less than $70/tCO2 for perhaps a century or more.

01 COAL, LIGNITE, AND PEAT↗