Search NASA⌕ Search

SEARCH · Search NASA

Results for “Low temperature plasma”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

ICP etching of GaN microstructures in a Cl 2 –Ar plasma with subnanometer-scale sidewall surface roughness

In this work, substrate temperature, RF power, and ICP power were investigated for their effects on GaN micropillar sidewall roughness and etch characteristics. Elevated substrate temperature was shown to improve the sidewall etch morphology at low RF powers (reduced physical bombardment) and low ICP powers (lower plasma densities). Increased lateral etching is observed with both increased ICP power and substrate temperature, which both act to increase the chemical component of the etch. Etch conditions with a high chemical driving force resulted in faceting along the a-plane on the sidewalls. This faceting produced extremely smooth surfaces with root-meansquare roughness (R q ) as low as 0.20 nm which is comparable to typical epitaxy-ready surfaces and smaller than the a-plane lattice spacing of 0.3186 nm. The smooth surfaces produced in this study enable possibilities for laser facets or for new device structures that require high quality surfaces for GaN regrowth.

36 MATERIALS SCIENCE↗
NASA NTRS2001

Low-Latitude Solar Wind During the Fall 1998 SOHO-Ulysses Quadrature

The Fall 1998 SOlar-Heliospheric Observatory (SOHO) - Ulysses quadrature occurred when Ulysses was at 5.2 AU, 17.4 deg South of the equator, and off the West line of the Sun. SOHO coronal observations, at heliocentric distances of a few solar radii, showed that the line through the solar center and Ulysses crossed, over the first days of observations, a dark, weakly emitting area and through the northern edge of a streamer complex during the second half of the quadrature campaign. Ulysses in situ observations showed this transition to correspond to a decrease from higher speed wind typical of coronal hole flow to low speed wind. Physical parameters (density, temperature, flow speed) of the low latitude coronal plasma sampled over the campaign are determined using constraints from what is the same plasma measured later in situ and simulating the intensities of the Hydrogen Lyman-alpha and OVI 1032 and 1037 Angstrom lines, measured by the Ultra Violet Coronagraph Spectrometer (UVCS) on SOHO. The densities, temperatures and outflow speed are compared with the same characteristic flow parameters for high-latitude fast wind streams and typical slow solar wind.

Poletto, G.↗
NASA NTRS1980

New advances in thermal plasma research

Recent measurements obtained of the cold or thermal plasma of the earth's magnetosphere, which is believed to originate in the ionosphere, are reviewed. Consideration is given to the results of ATS 6 measurements which indicated unexpectedly high plasma temperatures and varied pitch-angle distributions, and the data from the low-energy plasma experiments on board GEOS 1 and 2 and ISEE 1, which were intended to clarify the ATS 6 results. These later measurements of ion composition, plasma energy and plasma distribution are noted to have confirmed earlier data and discovered new plasma components (D(+) or He(+2)), an intermixing of cold ionospheric plasma and hot magnetospheric plasma, the ordering of the plasma by the magnetic field rather than the ram direction in the outer magnetosphere, and wave phenomena. Questions remaining concerning the temperature and composition distributions of the plasmasphere and plasma trough, the relative densities of the cold and warmer components of the magnetosphere, plasma energization mechanisms, and the relative mix of the various plasma distributions are indicated.

Chappell, C. R.↗
NASA NTRSDate not supplied

Spacecraft Charging as an Asset to Interplanetary Small Spacecraft

Small spacecraft operate on a far more limited power budget than their larger counterparts, a problem compounded for interplanetary spacecraft in the outer solar system. The reduced solar flux beyond Earth’s orbit makes solar panels less effective for spacecraft exploring the gas giants and can they are susceptible to damage by intense radiation belts. Radioisotope thermoelectric generators are expensive and bulky compared to their power output. Interplanetary small satellite missions benefit from both alternative energy sources and low-power electronics to power their buses and scientific payloads. Traditionally, spacecraft engineers treat the space environment as a hazard, but it nevertheless offers a potential solution. Currents from space plasmas charge spacecraft to high potentials and can cause electrical arcing to occur between differentially charged surfaces. The spacecraft can harvest a small amount of power —<10 mW/m2at Jupiter — from the electric field between these surfaces to do useful work, either by charging a battery or directly powering an instrument or actuator. While using the energy directly has limited use due to the low electron density and temperature of most space plasmas, it can nevertheless be used in situations where solar panels are not desirable, such as high radiation environments. Two applications — a Langmuir probe and an attitude control actuator — exploit the disparate current-voltage characteristics between surfaces with different material properties and require minimal input power to operate.

Spacecraft↗
NASA NTRSDate not supplied

Spacecraft Charging as an Asset to Interplanetary Small Spacecraft

Small spacecraft operate on a far more limited power budget than their larger counterparts, a problem compounded for interplanetary spacecraft in the outer solar system. The reduced solar flux beyond Earth’s orbit makes solar panels less effective for spacecraft exploring the gas giants and they are susceptible to damage by intense radiation belts. Radioisotope thermoelectric generators are expensive and bulky compared to their power output. Interplanetary small satellite missions benefit from both alternative energy sources and low-power electronics to power their buses and scientific payloads. Traditionally, spacecraft engineers treat the space environment as a hazard, but it nevertheless offers a potential solution. Currents from space plasmas charge spacecraft to high potentials and can cause electrical arcing to occur between differentially charged surfaces. The spacecraft can harvest a small amount of power —<10 mW/m2at Jupiter — from the electric field between these surfaces to do useful work, either by charging a battery or directly powering an instrument or actuator. While using the energy directly has limited use due to the low electron density and temperature of most space plasmas, it can nevertheless be used in situations where solar panels are not desirable, such as high radiation environments. Two applications — a Langmuir probe and an attitude control actuator — exploit the disparate current-voltage characteristics between surfaces with different material properties and require minimal input power to operate.

spacecraft charging↗
DOE OSTI2025

Compositionally-driven surface nanostructuring on refractory compositionally complex alloys under low energy helium bombardment

Additive manufacturing enables user-defined control of the compositional complexity, opening new design spaces for complex concentrated alloys (CCAs). Refractory CCAs may offer enhanced performance in the divertor region of a fusion reactor environment where plasma-facing materials will be subject to high temperatures, low energy He and D particles, and 14 MeV neutrons. In this work, specimens with the nominal composition of NbTaMoTi, NbTaMo, NbTaTi, and NbTa were fabricated via directed energy deposition (DED) then bombarded with 40 eV He ions to a fluence of 2x10 26 m −2 at ∼ 1000 K. Post irradiation, the surface morphology and composition were examined with electron microscopy and x-ray photoelectron spectroscopy to offer information on the spatial distribution of surface nano-structuring. Sub-surface He bubbles driving the nano-structuring were examined with electron microscopy techniques. Analysis indicates the local composition directly influences the He bubble and tendril size, while the region with the highest complexity showed the shortest nano-structuring. Molecular Dynamics simulations complement the experimental results, showing comparable helium bubble growth and migration as a function of compositional complexity. This work demonstrates the compositional dependence of surface nanostructure formation of compositionally complex alloys, important for future design of complex plasma facing materials in fusion reactors.

Complex concentrated alloys↗
NASA NTRS1975

The spatial and temperature structure of vacuum spark plasmas

The spatial and temperature structures of the X-ray emitting components of low-inductance vacuum-spark plasmas are investigated. The plasmas produced by low-inductance vacuum sparks show striking resemblances to solar-flare plasmas. High-resolution photographs show that the spark plasmas are composed of hot (about 30 million K) compact sources (less than 20 microns) and cooler (about 10 million K) larger sources (of the order of 100 microns). Both types of sources may be produced by the same plasma at different times. The differences between the solar flare iron-line spectrum near 1.9 A and the spark iron-line spectrum are discussed and interpreted.

Feldman, U.↗
DOE OSTI2020

Lithium splashing from flowing liquid lithium limiter and its effect on high confinement plasma performance in EAST tokamak

To study the potential applications of liquid lithium (Li) as plasma facing material, the third generation of flowing liquid Li (FLiLi) limiter has been designed and successfully tested in EAST tokamak H-mode discharges in the 2018 run campaign. Here, the stability of liquid Li on FLiLi surface, and Li splashing and its effect on the plasma performance are investigated in detail. Li splashing was observed in L-mode and H-mode discharges due to Rayleigh-Taylor (R-T) instability, resulting from electromagnetic forces J → x B → . Li splashing in low-parameter plasma decreased both core and edge electron temperatures, resulting in the degradation of plasma energy confinement and even H-L back transition, however, it almost did not influence plasma confinement performance in high-parameter plasma. These findings indicate that high-parameter plasma has higher tolerance to Li impurities than low-parameter plasma. By contrast, tungsten splashing from the melted layer on the upper divertor was also induced by the R-T instability but generally resulted in plasma disruption, which suggests lower tolerance to tungsten impurities in EAST tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1990

Study of a cesium plasma as a selective emitter for thermophotovoltaic applications

This experimental study evaluates the potential of a cesium plasma as an emitter for a thermophotovoltaic (TPV) energy conversion system. A cesium plasma, as a result of the ground-state transitions of its single outer-shell electron, produces large amounts of radiation in the 850-890-nm wavelength region. This would provide excellent coupling to silicon, gallium arsenide, and indium phosphide photovoltaic cells. Measurements of the radiative efficiency, the sum of the power at the 852 and 894 nm wavelengths relative to the total emitted power, were made and correlated to the plasma operating variables. It was determined that, for atomic density in the range (3-6) x 10 exp 21/cu cm and electron temperature in the range 2000-3000 K, radiative efficiencies in excess of 70 percent are attainable. This would indicate that a cesium plasma with its selective emission characteristics and low electron operating temperatures of 2000-3000 K would be an excellent candidate as an emitter in a TPV system.

Lowe, R.↗
NASA NTRS1991

Voyager 2 electron observations in the magnetosphere of Neptune

This paper describes electron data obtained during the Neptune encounter by the Voyager 2 plasma science experiment. The densities and temperatures of low-energy (10-5950 eV) electrons and the electrostatic potential of the spacecraft near Neptune are derived. The data indicate that the escape of charged particles from Triton and the local ionization of atoms in the neutral torus originating from Triton are the major plasma sources. It is inferred that this neutral torus of hydrogen atoms has a density of about 300/cu cm and an inner boundary at 8 R(N). The data near Neptune exhibit signatures suggesting that both precipitation into Neptune's atmosphere and ring absorption are important plasma loss mechanisms. Plasma transport in the magnetosphere appears to be very fast; the diffusion coefficient is 1 x 10 exp -7 L exp 3 R(N) exp 2/sec.

Zhang, Ming↗
NASA NTRS1970

High temperature ion source

Modified Nielsen-type ion source produces temperatures up to 1500 degrees C and permits obtaining a plasma from low vapor-pressure materials. Design minimizes thermal stresses. Dual-filament discharge chamber achieves the high temperature and provides independent control of the heating and electron emission functions.

Swift, R.↗
DOE OSTI2022

Multi-harmonic electron cyclotron heating and current drive scenarios for non-inductive start-up and ramp-up in high field ST-40 spherical tokamak

We report non-inductive start-up and ramp-up is an important topic for spherical tokamak reactor design as the central solenoid implementation is highly restrictive particularly for the low-aspect-ratio tokamak configuration. In the high field spherical tokamak (ST), ST-40 with B T0 ≤ 3 T, a preparation is underway for high power ECH and ECCD current start-up/ramp-up experiments utilizing two MW-class 140/105 GHz gyrotrons. Here, we explored various ECH/ECCD scenarios for a low-field-side (LFS) launch-angle steerable waveguide launcher placed near the mid-plane region. Due to the large toroidal field variation of ST configuration, multiple cyclotron harmonic resonance layers could exist within the plasma. In this start-up and ramp-up regime, both fundamental and second harmonic ECH resonances must be considered. We find that even with the presence of X-II resonance layer in the plasma, an efficient X-I ECH and ECCD regime can be accessed for the low electron temperature T e0 as low as 200 eV which is a typical starting temperature of ECH heated plasmas in an open-field-line configuration. The presence of X-II resonance could become significant at higher T e0 as X-II absorption increases with T e0 which could reduce the current ramp-up efficiency as the power reaching X-I is reduced. Finally for the pure X-I regime where the 2Ω e resonance is moved outside the plasma with B T0 ~ 3.4 T, we find that it is possible to reach the full current of I p ~ 1 MA fully non-inductively with the ECH power of ~1 MW at n e0 ~ 1.0 × 10 19 m -3 using 105 GHz frequency gyrotron. By reducing the outer limiter position R L ~ 78 cm to 70 cm, the pure X-I regime is recovered at the rated ST-40 magnetic field of B T0 ~ 3.0 T. This X-I regime is accessible with a relatively broad range of launched n II or the launching angles. A survey of X-mode X-II ECH and ECCD at higher density regimes is also shown for completeness.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1992

Plasma reactor waste management systems

The University of North Dakota is developing a plasma reactor system for use in closed-loop processing that includes biological, materials, manufacturing, and waste processing. Direct-current, high-frequency, or microwave discharges will be used to produce plasmas for the treatment of materials. The plasma reactors offer several advantages over other systems, including low operating temperatures, low operating pressures, mechanical simplicity, and relatively safe operation. Human fecal material, sunflowers, oats, soybeans, and plastic were oxidized in a batch plasma reactor. Over 98 percent of the organic material was converted to gaseous products. The solids were then analyzed and a large amount of water and acid-soluble materials were detected. These materials could possibly be used as nutrients for biological systems.

Ness, Robert O., Jr.↗
DOE OSTI2025

Sensitivities of time-dependent temperature profile predictions for NSTX with the multi-mode model

The Multi-Mode Model (MMM) for turbulent transport was applied to a large set of well-analyzed discharges from the National Spherical Torus Experiment (NSTX) in order to evaluate its sensitivities to a wide range of plasma conditions. MMM calculations were performed for hundreds of milliseconds in each discharge by performing time-dependent predictive simulations with the 1.5D tokamak integrated modeling code TRANSP. A closely related study (Lestz et al 2025 Plasma Phys. Control. Fusion 67 105029) concluded that MMM predicted electron and ion temperature profiles that were in reasonable agreement with NSTX observations, generally outperforming a different reduced transport model, TGLF. This finding motivates the more thorough investigation of the characteristics of the MMM predictions conducted in this work. The simulations with MMM have electron energy transport dominated by electron temperature gradient modes in the examined discharges with relatively low plasma β (ratio of kinetic plasma pressure to magnetic field pressure) and high collisionality, transitioning to a mixture of different modes for higher β and lower collisionality. The thermal ion diffusivity predicted by MMM is much smaller than the neoclassical contribution, in line with previous experimental analysis of NSTX. Nonetheless, the electron and ion temperature profiles are coupled via collisional energy exchange and thus sensitive to which transport channels are predicted. The time-dependent simulations with MMM are robust to the simulation start time, converging to remarkably similar temperature profiles later during the discharge. MMM typically overpredicts confinement relative to NSTX observations, leading to the prediction of overly steep temperature profiles. Plasmas with spatially broader temperature profiles, higher plasma β, and longer energy confinement times tend to be predicted by MMM with better agreement with the experiment. As a result, these findings provide useful context for understanding the regime-dependent tendencies of MMM in anticipation of self-consistent, time-dependent predictive simulations of NSTX-U discharges with these same modeling tools.

MMM↗
NASA NTRS1980

Photonitride passivating coating for IC's

Increased reliability and simplified fabrication result from postassembly preencapsulation passivation process. Photonitride reaction chamber receives silane, ammonia, and mercury from mixing manifold to form passivating coating on IC's. Photonitride layer is barrier to moisture and penetration by mobile ions, and helps to protect IC devices subjected to severe mechanical handling or circuit repair procedures. Process is compatible with variety of wire-bonded lead frame assemblies. Advantages over plasma and sputtering deposition processes are low deposition temperature and zero stray radiation and ion levels.

Hall, T. C.↗
NASA NTRS1995

Cosmic dust synthesis by accretion and coagulation

The morphology of grains grown by accretion and coagulation is revaled by a new laboratory method of synthesizing cosmic dust analogs. Submicron carbon particles, grown by accretion of carbon atoms from a gas, have a spherical shape with a cauliflower-like surface and an internal micro-structure of radial columns. This shape is probably common for grains grown by accretion at a temperature well below the melting point. Coagulated grains, consisting of spheres that collided to form irregular strings, were also synthesized. Another shape we produced had a bumpy non- spherical morphology, like an interplanetary particle collected in the terrestrial stratosphere. Besides these isolated grains, large spongy aggregates of nanometer-size particles were also found for various experimental conditions. Grains were synthesized using ions to sputter a solid target, producing an atomic vapor at a low temperature. The ions were provided by a plasma, which also provided electrostatic levitation of the grains during their growth. The temporal development of grain growth was studied by extinguishing the plasma after various intervals.

Praburam, G.↗