Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microscope and microscopy.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Characterization of diamond-like nanocomposite thin films grown by plasma enhanced chemical vapor deposition

Diamond-like nanocomposite (DLN) thin films, comprising the networks of a-C:H and a-Si:O were deposited on pyrex glass or silicon substrate using gas precursors (e.g., hexamethyldisilane, hexamethyldisiloxane, hexamethyldisilazane, or their different combinations) mixed with argon gas, by plasma enhanced chemical vapor deposition technique. Surface morphology of DLN films was analyzed by atomic force microscopy. High-resolution transmission electron microscopic result shows that the films contain nanoparticles within the amorphous structure. Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and x-ray photoelectron spectroscopy (XPS) were used to determine the structural change within the DLN films. The hardness and friction coefficient of the films were measured by nanoindentation and scratch test techniques, respectively. FTIR and XPS studies show the presence of C-C, C-H, Si-C, and Si-H bonds in the a-C:H and a-Si:O networks. Using Raman spectroscopy, we also found that the hardness of the DLN films varies with the intensity ratio I{sub D}/I{sub G}. Finally, we observed that the DLN films has a better performance compared to DLC, when it comes to properties like high hardness, high modulus of elasticity, low surface roughness and low friction coefficient. These characteristics are the critical components in microelectromechanical systems (MEMS) and emerging nanoelectromechanical systems (NEMS).

36 MATERIALS SCIENCE↗

A miniaturized, high frequency mechanical scanner for high speed atomic force microscope using suspension on dynamically determined points

One of the major limitations in the speed of the atomic force microscope (AFM) is the bandwidth of the mechanical scanning stage, especially in the vertical (z) direction. According to the design principles of “light and stiff” and “static determinacy,” the bandwidth of the mechanical scanner is limited by the first eigenfrequency of the AFM head in case of tip scanning and by the sample stage in terms of sample scanning. Due to stringent requirements of the system, simply pushing the first eigenfrequency to an ever higher value has reached its limitation. We have developed a miniaturized, high speed AFM scanner in which the dynamics of the z-scanning stage are made insensitive to its surrounding dynamics via suspension of it on specific dynamically determined points. This resulted in a mechanical bandwidth as high as that of the z-actuator (50 kHz) while remaining insensitive to the dynamics of its base and surroundings. The scanner allows a practical z scan range of 2.1 μm. We have demonstrated the applicability of the scanner to the high speed scanning of nanostructures.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Catalytic synthesis of bamboo-like multiwall BN nanotubes via SHS-annealing process

Bamboo-like multiwall boron nitride (BN) nanotubes were synthesized via annealing porous precursor prepared by self-propagation high temperature synthesis (SHS) method. The as-synthesized BN nanotubes were characterized by the field emission scanning electron microscopy (FE-SEM), transmission electron microscope (TEM), high-resolution TEM (HRTEM), X-ray diffraction (XRD), Raman and Fourier transform infrared (FTIR) spectroscopy. These nanotubes have uniform diameters of about 60 nm and an average length of about 10 {mu}m. Four growth models, including tip, base, based tip and base-tip growth models, are proposed based on the catalytic vapor-liquid-solid (VLS) growth mechanism for explaining the formation of the as-synthesized bamboo-like BN nanotubes. Chemical reactions and annealing mechanism are also discussed. -- Graphical Abstract: A novel and effective annealing porous precursor route to bulk synthesis of bamboo-like multiwall BN nanotubes. Four growth models of VLS growth mechanism for these nanotubes are proposed. Display Omitted Research highlights: {yields} Bulk bamboo-like BN nanotubes were synthesized by SHS-annealing method. {yields} Boron-containing, porous precursor played a crucial role in bulk synthesis process. {yields} Four possible growth models were proposed to explain the formation of the bamboo-like BN nanotubes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Real space soft x-ray imaging at 10 nm spatial resolution

Using Fresnel zone plates made with our robust nanofabrication processes, we have successfully achieved 10 nm spatial resolution with soft x-ray microscopy. The result, obtained with both a conventional full-field and scanning soft x-ray microscope, marks a significant step forward in extending the microscopy to truly nanoscale studies.

36 MATERIALS SCIENCE↗

Application of spectroscopy and super-resolution microscopy: Excited state

Photophysics of inorganic materials and organic molecules in complex systems have been extensively studied with absorption and emission spectroscopy.1-4 Steady-state and time-resolved fluorescence studies are commonly carried out to characterize excited-state properties of fluorophores. Although steady-state fluorescence measurements are widely used for analytical applications, time-resolved fluorescence measurements provide more detailed information about excited-state properties and the environment in the vicinity of the fluorophore. Many photophysical processes, such as photoinduced electron transfer (PET), rotational reorientation, solvent relaxation, and energy transfer, occur on a nanosecond (10 -9 s) timescale, thus affecting the lifetime of the fluorophores. Moreover, time-resolved microscopy methods, such as lifetimeimaging, combine the benefits of the microscopic measurement and information-rich, timeresolved data. Thus, time-resolved fluorescence spectroscopy combined with microscopy can be used to quantify these processes and to obtain a deeper understanding of the chemical surroundings of the fluorophore in a small area under investigation. This thesis discusses various photophysical and super-resolution microscopic studies of organic and inorganic materials, which have been outlined below.

36 MATERIALS SCIENCE↗

Structural Origin of Overcharge-induced Thermal Instability of Ni-containing Layered-cathodes for High-energy-density Lithium Batteries

Using a combination of time-resolved X-ray diffraction (XRD), in situ transmission electron microscopy (TEM), and first principles calculations, we explore the structural origin of the overcharge induced thermal instability of two cathode materials, LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} and LiNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2}, which exhibit significant difference in thermal stabilities. Detailed TEM analysis reveals, for the first time, a complex core-shell-surface structure of the particles in both materials that was not previously detected by XRD. Structural comparison indicates that the overcharged Li{sub x}Ni{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} (x < 0.15) particles consist of a rhombohedral core, a spinel shell, and a rock-salt structure at the surface, while the overcharged LixNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2} consists of a similar core-shell-surface structure but a very different CdI{sub 2}-type surface structure. The thermal instability of LixNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} can be attributed to the release of oxygen because of the rapid growth of the rock-salt-type structure on the surface during heating. In contrast, the CdI{sub 2}-type surface structure of the overcharged LixNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2} particles delays the oxygen-release reaction to a much higher temperature resulting in better stability. These results gave deep insight into the relationship between the local structural changes and the thermal stability of cathode materials, which is vital to the development of new cathode materials for the next generation of lithium-ion batteries.

25 ENERGY STORAGE↗

Atomic force microscopy of biological samples

The ability to evaluate structural-functional relationships in real time has allowed scanning probe microscopy (SPM) to assume a prominent role in post genomic biological research. In this mini-review, we highlight the development of imaging and ancillary techniques that have allowed SPM to permeate many key areas of contemporary research. We begin by examining the invention of the scanning tunneling microscope (STM) by Binnig and Rohrer in 1982 and discuss how it served to team biologists with physicists to integrate high-resolution microscopy into biological science. We point to the problems of imaging nonconductive biological samples with the STM and relate how this led to the evolution of the atomic force microscope (AFM) developed by Binnig, Quate, and Gerber, in 1986. Commercialization in the late 1980s established SPM as a powerful research tool in the biological research community. Contact mode AFM imaging was soon complemented by the development of non-contact imaging modes. These non-contact modes eventually became the primary focus for further new applications including the development of fast scanning methods. The extreme sensitivity of the AFM cantilever was recognized and has been developed into applications for measuring forces required for indenting biological surfaces and breaking bonds between biomolecules. Further functional augmentation to the cantilever tip allowed development of new and emerging techniques including scanning ion-conductance microscopy (SICM), scanning electrochemical microscope (SECM), Kelvin force microscopy (KFM) and scanning near field ultrasonic holography (SNFUH).

59 BASIC BIOLOGICAL SCIENCES↗

Preface to Special Issue on Neutron Scattering for Catalysis

In the pursuit of understanding the chemical transformations of catalytic reactions and the structural evolution of catalysts at the molecular level, a suite of advanced experimental methods has been developed in the studies of catalysis science. Furthermore, among these methods, neutron scattering not only gives catalytic information that is highly complementary to other microscopic scattering techniques such as electrons (microscopy and diffraction) and photons from visible light to synchrotron X-rays, but also frequently provides unique insights into catalysis regarding the structure and chemical nature of light elements such as hydrogen and oxygen that are either not possible or difficult to study with other approaches.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Interfacial Microstructure and Mechanical Properties of Friction Stir Welded Joints of Commercially Pure Aluminum and 304 Stainless Steel

In the present investigation, friction stir welding of commercially pure aluminum and 304 stainless steel was carried out at varying tool rotational speeds from 200 to 1000 rpm in steps of 200 rpm using 60 mm/min traverse speed at 2 (degree) tool tilt angle. Microstructural characterization of the interfacial zone was carried out using optical microscope and scanning electron microscope. Energy-dispersive spectroscopy indicated the presence of FeAl{sub 3} intermetallic phase. Thickness of the intermetallic layer increased with the increase in tool rotational speed. X-ray diffraction studies indicated the formation of intermetallic phases like FeAl{sub 2}, Fe{sub 4}Al{sub 13}, Fe{sub 2}Al{sub 5}, and FeAl{sub 3}. A maximum tensile strength of ~ 90% that of aluminum along with ~ 4.5% elongation was achieved with the welded sample at tool rotational speed of 400 rpm. The stir zone showed higher hardness as compared to base metals, heat affected zone, and thermo-mechanically affected zone due to the presence of intermetallics. The maximum hardness value at the stir zone was achieved at 1000 rpm tool rotational speed.

36 MATERIALS SCIENCE↗

Studies on Enhancement of Silt Erosion Resistance of 13/4 Martensitic Stainless Steel by Low-Temperature Salt Bath Nitriding

Low-temperature salt bath nitriding of heat treated and tempered 13/4 Martensitic stainless steel (13/4HTT) was carried at 450 °C (N450) and 500 °C (N500) for 10 h each. The nitrided samples were characterized by using x-ray diffractometer, field emission scanning electron microscope and optical microscope. The nanohardness and elastic modulus of the cross section of nitrided specimen were measured by nanoindentation test using Hysitron TI950 triboindenter. The nitrided 13/4HTT (N450 and N500) and 13/4HTT specimens were subjected to slurry erosion test in a slurry pot tester. The test was conducted for 48 h, and weight loss was measured after every 6 h. The relative speed of slurry with respect to specimen was 4.55 m/s. It was found that the weight loss due to erosion of the N450 is 83% less than that of 13/4HTT and that of N500 was 92% more than that of 13/4HTT. The erosion mechanism is correlated to the phases present in the specimens. The improvement in the slurry erosion resistance of N450 is due to presence of expanded martensite (α{sub N}-Fe). Increasing the temperature of nitriding to 500 °C led to the decrease in the slurry erosion resistance of N500 due to the formation of brittle CrN phase.

36 MATERIALS SCIENCE↗

Effect of Deep Cryogenic Treatment on Mechanical Properties and Microstructure of the Tool Steel CR7V for Hot Stamping

To solve the failure problem of hot stamping tool, the CR7V steel was deep cryogenically treated at different dwelling times with multiple tempering. The hardness, impact toughness and wear resistance of the CR7V steel were examined, and the effects of deep cryogenic treatment on the microstructure of the CR7V steel were studied by means of optical microscope, scanning electron microscope and energy-dispersive spectroscopy. The results show that deep cryogenic treatment has little effect on the hardness of the tempered CR7V steel, but improves its impact toughness and wear resistance. The improvement in mechanical properties is a result of the combination of dissolution of large carbide particles, formation of small-sized and uniformly distributed carbide particles and fine tempered martensite structure. The cryogenic treatment is optimized as follows: vacuum gas quenching, deep cryogenic treatment at − 196 °C for 6 h and triple tempering at 560 °C for 2 h, which improves the wear resistance by 68% and the impact toughness by 58% compared to the conventional heat treatment.

36 MATERIALS SCIENCE↗

Corrosion Behavior of Q235 Steel Exposed in Deepwater of South China Sea

For the first time, the corrosion behavior of Q235 steel in 1200, 2000 and 3000 m deepwater of South China Sea for 0.5 year was reported in this study. The corrosion morphology and corrosion products properties were investigated using different techniques, such as 3D optical microscope, scanning electron microscope, x-ray diffraction analyzer and electrochemical impedance spectroscopy. The main environmental factors influencing the corrosion rate of Q235 in deep sea were discussed by applying gray relational analysis. The results indicated that uniform thinning occurred after exposure. A large number of tiny pits were distributed under the corrosion products with a two-layer structure. The corrosion rate and average pitting depth of samples exposed at 2000 m were lower than those exposed at 1200 and 3000 m, and the main environmental factors determining the variation of corrosion rate at different depths were temperature and dissolved oxygen concentration. Hydrostatic pressure had slight effect on the corrosion rate of Q235 steel, but promoted the formation of a more uniform corrosion morphology.

36 MATERIALS SCIENCE↗

Studies on Bio-acceptability of Thermo-Mechanically Processed Mg-4Li-0.5Ca Alloy and Its Microstructural Correlation

In this study, in vitro corrosion behavior of rolled Mg-4Li-0.5Ca (wt.%) alloy at three temperatures (250, 300 and 350 °C) with 75% reduction and subsequent short annealing at 200 °C for 10 min was systematically investigated. Microstructural evaluation, Mg{sub 2}Ca precipitation and defects like twins were characterized by an optical microscope, scanning electron microscope and x-ray diffraction. Micrographs reveal an increase in grain size and comparatively reduction in twins density population with an increase in hot rolling temperature and subsequent short annealing. In vitro corrosion tests like dynamic bio-corrosion immersion test, hydrogen evolution test and electrochemical linear polarization test were carried out in simulated body fluid. From in vitro corrosion tests, it is observed that the alloy rolled at 350 °C and subsequently short-annealed shows better bio-corrosion resistance than other hot-rolled and short-annealed alloys. This is due to low twins density and uniformly dispersed Mg{sub 2}Ca compound throughout the matrix.

36 MATERIALS SCIENCE↗

Effect of Y/Zr Ratio on Inclusions and Mechanical Properties of 9Cr-RAFM Steel Fabricated by Vacuum Melting

This study investigates the inclusions, microstructures, tensile properties, and impact toughness of reduced-activation ferritic/martensitic (RAFM) steels with different Y/Zr ratio contents. An optical microscope and a scanning electron microscope (SEM) were employed to determine the size and number of inclusions, and SEM and transmission electron microscope were employed to examine the inclusion types. The increase in Y/Zr ratio influenced the prior austenite grain size owing to the pinning effect of the inclusions. The result of this examination showed that the mechanical properties of the steel are closely related to the refinement of prior austenite grain size and as well as the fine submicron-sized inclusions. The average prior austenite grain sizes of the alloys were 14.5, 13.5, and 13.4 μm for the steels with different Y/Zr ratio contents (i.e., 1/2, 5/3, and 11/2, respectively). Moreover, the submicron-sized inclusions in the alloys achieved densities of 4.71 × 10{sup 16}, 4.49 × 10{sup 16}, and 3.84 × 10{sup 16}/m{sup 3}. The ductile-to-brittle transition temperature (DBTT) decreases when the Y/Zr ratio increases to 5/3. However, the DBTT increases when the Y/Zr ratio reaches 11/2 owing to inclusion coarsening. The RAFM steel with Y content of approximately 0.005 wt.% and Zr content of 0.002 wt.% was verified to exhibit an optimized combination of microstructures, tensile properties, and impact toughness.

36 MATERIALS SCIENCE↗

Effect of Martensite Content on Failure Behavior of Laser Welded Dual-Phase Steel Joints During Deformation

Laser welding was applied to three types of dual-phase (DP) steel sheets (DP590, DP780, and DP980) with different martensite contents. The microstructure of laser welded joints was observed by optical microscope and scanning electron microscope, and the hardness of welded joints was measured by a microhardness tester. The tensile testing machine and the Erichsen test machine were employed to measure the tensile properties and forming properties of welded joints, respectively. The microstructure model showed that the welded joints of three different materials all contained a hardened zone (HZ) that was composed of a fusion zone, a coarse-grained heat-affected zone, and fine-grained heat-affected zone. The microstructure of the HZ contained mainly martensite such that the average martensite content of welded joints was increased by 1.9-9.8%, and the microhardness of the HZ was 1.2-1.9 times that of the base metal (BM). Moreover, the elongation of welded joints decreased with decreasing martensite content in the BM, and the effect was severe for the DP590 welded joint (21.8%) compared to the other two welded joints. During the Erichsen test, deformation failure varied among the welded joints with different martensite contents, and it was determined by the HZ and softened zone. The fracture occurred in the softened zone and ran parallel along the zone for DP980 welded joints, whereas the fracture occurred in the HZ and ran perpendicular to this zone for the other two welded joints. The Erichsen values of the DP590, DP780, and DP980 welded joints were 81.1, 91.7, and 85.0% of the BM, respectively.

36 MATERIALS SCIENCE↗

Microstructure and Properties of A356 Alloy Wheels Fabricated by Low-Pressure Die Casting with Local Squeeze

The low-pressure die-casting process (LPDC) is widely used in fabricating aluminum alloy automotive wheels. With good castability and mechanical properties, A356 alloys are important and common materials for LPDC wheels. However, in practical casting process, defects often appear, especially porosities in the wheel thick-walled parts (i.e., spoke) due to inadequate interdendritic feeding, which greatly decreases the mechanical properties. In this investigation, to deal with this problem, local squeeze (LS) was added in conventional LPDC to enhance the interdendritic feeding. The practical A356 alloy wheel castings were fabricated with different LS velocities and times. The quantitative characteristics of α-Al cells, Si particles, and porosities with and without the LS analyzed by optical microscope, scanning electron microscope, and 3D x-ray computed tomography were compared. Their effects on the tensile and impact properties were discussed. The results have shown that the LS can increase the cooling rate and feed shrinkage of spoke parts, hence resulting in finer grains and denser microstructure. In result, the properties of spoke parts were improved with the LS.

36 MATERIALS SCIENCE↗

Influence of Multidirectional Forging on Microstructural, Mechanical, and Corrosion Behavior of Mg-Zn Alloy

Multidirectional forging (MDF) was applied to Mg-6%Zn alloy up to 5 passes successfully at 280 °C. MDF-processed materials were characterized using optical microscope, scanning electron microscope, electron backscatter diffraction, transmission electron microscope, and x-ray diffraction. Obtained results showed a significant reduction in grain size (up to 3.8 μm) having a large fraction of high-angle grain boundaries after 5 passes of MDF process. Maximum tensile strength of 230 MPa was achieved for 5-pass MDF-processed Mg-6%Zn alloy which is about ~ 2.0 times higher in comparison with that of homogenized alloy (117 MPa) and was attributed to higher dislocations density and grain refinement. Corrosion behavior of the alloy was investigated in 0.1 M NaCl solution using potentiodynamic polarization test, electrochemical impedance spectra analysis, and immersion tests. It was found that the corrosion rate of 5-pass MDF sample improved (0.34 mm/year) ~2.5 times in comparison with that of homogenized Mg-6%Zn alloy (0.86 mm/year) due to fine grain structure, which creates more grain boundaries that act as a corrosion barrier.

36 MATERIALS SCIENCE↗

Retained Austenite Attributes and Mechanical Performance of Different Compositions of TRIP Steel Alloys

The main objective of this work is to correlate the different attributes of retained austenite phase in TRIP steel structure with its mechanical properties. Three different chemical compositions were used to produce TRIP steel alloys. The first alloy contains only silicon as a carbide precipitation inhibitor; in the second alloy, silicon is partially replaced with aluminum, while in the third alloy phosphorus is added to the silicon–aluminum alloy. These compositions were proposed in order to avoid the negative effect of silicon during galvanizing. These three steel alloys were cast, homogenized, hot-forged and then subjected to intercritical annealing treatment followed by cooling and isothermal treatment in salt bath with subsequent air-cooling. Microstructural characterization, using optical microscope, SEM and XRD, along with tensile testing was carried out. Retained austenite attributes include volume fraction, carbon content, total carbon content, retained austenite transformable index and its stability coefficient against strain-induced martensite (SIM) transformation. The effect of these attributes on the mechanical properties of the studied TRIP steel alloys was evaluated using tensile test date, i.e., ultimate tensile strength (UTS), ductility, yield strength to UTS ratio, performance index and strain-hardening exponent. The variation of strain-hardening rate and strain-hardening exponent with strain was also considered. The failure behavior of the studied steel alloys was investigated using SEM on tensile-tested specimens. The results show that Si/Al-alloy has the lowest retained austenite transformable index, lowest stability coefficient against SIM transformation, highest performance index and more stable and uniform variation in strain-hardening rate and strain-hardening exponent with strain. These properties satisfy the industrial constrains of the sheets used in automotive industry relating to better mechanical properties and galvanizability.

36 MATERIALS SCIENCE↗