Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mixing layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Radio frequency mixing modules for superconducting qubit room temperature control systems

As the number of qubits in nascent quantum processing units increases, the connectorized RF (radio frequency) analog circuits used in first generation experiments become exceedingly complex. The physical size, cost, and electrical failure rate all become limiting factors in the extensibility of control systems. We have developed a series of compact RF mixing boards to address this challenge by integrating I/Q quadrature mixing, intermediate frequency/LO (local oscillator)/RF power level adjustments, and direct current bias fine tuning on a 40 × 80 mm 2 four-layer printed circuit board with electromagnetic interference shielding. The RF mixing module is designed to work with RF and LO frequencies between 2.5 and 8.5 GHz. The typical image rejection and adjacent channel isolation are measured to be ~27 dBc and ~50 dB. By scanning the drive phase in a loopback test, the module short-term amplitude and phase linearity are typically measured to be 5 ×10 -4 (V pp /V mean ) and 1 ×10 -3 radian (pk-pk). The operation of the RF mixing board was validated by integrating it into the room temperature control system of a superconducting quantum processor and executing randomized benchmarking characterization of single and two qubit gates. We measured a single-qubit process infidelity of 9.3(3) × 10 -4 and a two-qubit process infidelity of 2.7(1) × 10 -2 .

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Combustion of 10–100 μm aluminum droplets in detonation products gases

Here we describe a two-phase model of combustion effects in aluminized high explosive (HE) charges. It is based on: (i) a Gas Dynamic Model of the expansion of the detonation product gases and their turbulent combustion with air; and (ii) a Heterogeneous Continuum Model of aluminum (Al) droplets and their combustion with the detonation product gases. Initial conditions are based on an analytical similarity solution for a cylindrical Chapman-Jouguet (CJ) detonation propagating at the CJ detonation velocity. The CJ jump conditions are computed at the thermodynamic equilibrium state by the Cheetah code, assuming the Al droplets are inert. We assume that the Al is 10 % of the charge mass and occurs as droplets at the CJ state. Different initial droplet diameters, ranging from 10 to 100 microns, are studied. A hydrodynamic combustion model based on large Damköhler numbers is employed in this study, -3σ(1 + 0.276 $\sqrt{Re}$)/($Kd^2_w$). It has a square-root dependence on the Reynolds number (Re) and inversed-squared dependence on the droplet diameter (d w ). The burnout time (t B ) of the Al droplets has a three-halves dependence on the droplet diameter, t B ~ ($d^0_w$) 3/2 . After burnout, the detonation products act as detonation products of the HE charge with active Al. They turbulently mix with air and form a combustion layer on the outer edge of the fireball. Details of the two-phase model, initial conditions and evolution of the flow field will be described.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Free-spray characteristics and spray-wall interactions of methanol on a gasoline direct injector under flash-boiling and non-flash-boiling conditions

Methanol is considered a promising alternative fuel for internal combustion engines (ICEs) due to its high-octane number, fast laminar flame speed, and elevated latent heat of vaporization, all of which support higher compression ratios and improved thermal efficiency. However, its substantial latent heat of vaporization also poses cold-start challenges, such as misfire and fuel film deposition. This study aims to investigate methanol spray morphology and spray-wall interaction using the Spray M injector from the Engine Combustion Network within a constant-pressure flow vessel. A recently developed unified numerical framework capable of modeling both flash and non-flash boiling sprays is validated against experimental liquid volume fraction data acquired via 3-D computed tomography. Here, the results reveal that flash boiling significantly alters the spray morphology, leading to smaller droplets and spray collapse due to enhanced air-entrainment-induced turbulence. Quantitative agreement between experiments and simulations confirms this behavior. Coupled 0-D equilibrium and 3-D computational fluid dynamics analyses show that flash boiling accelerates evaporation and reduces fuel residence time, while non-flash conditions maintain a persistent liquid core more susceptible to wall wetting. Wall temperature diagnostics reveal that spray collapse alters heat transfer patterns by shifting cooling effects. Mixture fraction analysis indicates that evaporation is primarily governed by shear-layer turbulence, though deviations from adiabatic equilibrium mixing emerge under low-turbulence conditions. Finally, increasing fuel, ambient, and wall temperatures reduces wall wetting and film thickness, mitigating cold-start risks. These findings enhance the understanding of methanol sprays’ behavior and support its adoption as a viable, alternative fuel for ICEs.

Engine Combustion Network↗
DOE OSTI2026

Deterministic Fabrication of Large-Area, High-Crystallinity Oxide Moiré Superlattices

Oxide twistronics extends moiré engineering beyond van der Waals materials, offering a promising platform for accessing emergent interfacial phenomena arising from the strong coupling of lattice, charge, and orbital degrees of freedom in complex oxides. However, deterministic fabrication of high-crystallinity oxide moiré superlattices over large lateral dimensions remains challenging due to the three-dimensional bonding network of oxides. Here, we demonstrate a scalable, generalized fabrication strategy that enables the formation of high-crystallinity oxide moiré superlattices with clean, chemically bonded interfaces and precisely controlled twist angles down to nominal values of 0.1°, achieving subdegree twist-angle accuracy across large contiguous lateral dimensions approaching the millimeter scale. Using NaNbO3 as a model system, we show that the resulting interlayer coupling drives pronounced structural reconstruction that modifies both the phase structure and ferroelectric domain configuration. Synchrotron-based X-ray 3D reciprocal space mapping reveals the emergence of a single-phase state in twisted bilayers, in contrast to the mixed-phase structure observed in single-layer membranes prior to twist assembly. The structural signatures are further consistent with gradual lattice rotation distributed along the thickness direction that may accommodate interfacial shear strain, distinct from reconstruction observed in van der Waals moiré systems which primarily occurs through in-plane stacking rearrangement. This collective lattice response is correlated with twist-dependent nanoscale electromechanical modulations observed by piezoresponse force microscopy. These results establish a scalable materials platform for oxide twistronics and support the implementation of twist-engineered functionalities in practical, macroscale device architectures.

Ghanbari, Reza [North Carolina State University (N↗
DOE OSTI2026

Influence of Surface Aerosol Injection on Stratocumulus‐to‐Cumulus Transition: Cloud‐Surface Coupling and Background Aerosol Concentrations

The influence of surface aerosol injection on the stratocumulus‐to‐cumulus transition (SCT) is explored using large‐eddy simulations. We examine how cloud‐surface coupling (or the strength of the marine boundary layer (MBL) stratification that limits vertical turbulent mixing and convection) impacts the vertical transport of aerosols, and how injected aerosols influence cloud properties and associated cloud radiative effects during the SCT. By injecting aerosols at different stages of the SCT, noting that cloud is more decoupled from the surface over time due to entrainment warming, we find that cloud‐surface coupling significantly affects aerosol vertical transport. However, injection timing (before drizzle if any) does not notably affect the SCT and the efficiency of marine cloud brightening, because aerosol number concentrations due to injections at different times rapidly converge before the transition onset. By varying the background aerosol concentration, we find that injected aerosols can significantly extend the persistence of stratocumulus decks by suppressing precipitation in clean environments but have little impact on stratocumulus breakup with higher background aerosol concentrations due to saturated aerosol effects. In clean MBLs, the SCT‐delay‐induced increase in cloud fraction dominates the overall cooling effects in response to aerosols, followed by Twomey effects. These cooling effects are slightly offset by decreased liquid water path (LWP) due to entrainment drying. In polluted MBLs, the Twomey effect is more dominant, followed by cloud fraction adjustments, and these coolings are also partly offset by LWP adjustments. All the simulations are made in relatively small domains in which injected aerosols are homogenized over a short time scale.

Zhang, Haipeng [Univ. of Maryland, College Park, M↗
DOE OSTI2020

Universal and versatile morphology engineering via hot fluorous solvent soaking for organic bulk heterojunction

After explosive growth of efficiency in organic solar cells (OSCs), achieving ideal morphology of bulk heterojunction remains crucial and challenging for advancing OSCs into consumer market. Herein, by utilizing the amphiphobic nature and temperature-dependent miscibility of fluorous solvent, hot fluorous solvent soaking method is developed to optimize the morphology with various donor/acceptor combinations including polymer/small-molecule, all-polymer and all-small-molecule systems. By immersing blend film into hot fluorous solvent which is utilized as liquid medium with better thermal conductivity, the molecular reorganization is accelerated. Furthermore, fluorous solvent can be miscible with the residue of chloroform and chloronaphthalene above upper critical solution temperature. This mixed solvent diffuses around inside the active layer and selectively promotes molecular reorganization, leading to optimized morphology. Compared to widely-used thermal annealing, this approach processed under mild conditions achieves superior photovoltaic performance, indicating the practicality and universality for morphological optimization in OSCs as well as other optoelectronic devices.

14 SOLAR ENERGY↗
DOE OSTI2020

$t_1$-Noise eliminated dipolar heteronuclear multiple-quantum coherence solid-state NMR spectroscopy

Heteronuclear correlation (HETCOR) spectroscopy is one of the key tools in the arsenal of the solid-state NMR spectroscopist to probe chemical and spatial proximities between two different nuclei and enhance spectral resolution. Dipolar heteronuclear multiple-quantum coherence (D-HMQC) is a powerful technique that can be potentially utilized to obtain 1 H detected 2D HETCOR solid-state NMR spectra of any NMR active nucleus. A long-standing problem in 1 H detected D-HMQC solid-state NMR experiments is the presence of t 1 -noise which reduces sensitivity and impedes spectral interpretation. In this contribution, we describe novel pulse sequences, termed t 1 -noise eliminated (TONE) D-HMQC, that minimize t 1 -noise and can provide higher sensitivity and resolution than conventional D-HMQC. Monte-Carlo and numerical simulations confirm that t 1 -noise in conventional D-HMQC primarily occurs because random MAS frequency fluctuations cause variations in the NMR signal amplitude from scan to scan, leading to imperfect cancellation of uncorrelated signals by phase cycling. The TONE D-HMQC sequence uses 1 H π-pulses to refocus the evolution of 1 H CSA across each SR4 2 1 recoupling block, improving the stability of the pulse sequence to random MAS frequency fluctuations. The 1 H refocusing pulses also restore the orthogonality of in-phase and anti-phase magnetization for all crystallite orientations at the end of each recoupling block, enabling the use of 90° flip-back or LG spin-lock trim pulses to reduce the intensity of uncorrelated signals. We demonstrate the application of these methods to acquire 1 H detected 2D 1 H{ 35 Cl} and 1 H{ 13 C} HETCOR spectra of histidine·HCl·H 2 O with reduced t 1 -noise. To show generality, we also apply these methods to obtain 2D 1 H{ 17 O} spectra of 20%- 17 O fmoc-alanine and for the first time at natural abundance, 2D 1 H{ 25 Mg} HETCOR spectra of magnesium hydroxide. The TONE D-HMQC sequences are also used to probe 1 H– 25 Mg and 1 H– 27 Al proximities in Mg–Al layered double hydroxides and confirm the even mixing of Mg and Al in these materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

From hydrogen to helium: the spectral evolution of white dwarfs as evidence for convective mixing

ABSTRACT We present a study of the hypothesis that white dwarfs undergo a spectral change from hydrogen- to helium-dominated atmospheres using a volume-limited photometric sample drawn from the Gaia-DR2 catalogue, the Sloan Digital Sky Survey (SDSS), and the Galaxy Evolution Explorer (GALEX). We exploit the strength of the Balmer jump in hydrogen-atmosphere DA white dwarfs to separate them from helium-dominated objects in SDSS colour space. Across the effective temperature range from 20 000 to 9000 K, we find that 22 per cent of white dwarfs will undergo a spectral change, with no spectral evolution being ruled out at 5σ. The most likely explanation is that the increase in He-rich objects is caused by the convective mixing of DA stars with thin hydrogen layers, in which helium is dredged up from deeper layers by a surface hydrogen convection zone. The rate of change in the fraction of He-rich objects as a function of temperature, coupled with a recent grid of 3D radiation-hydrodynamic simulations of convective DA white dwarfs – which include the full overshoot region – lead to a discussion on the distribution of total hydrogen mass in white dwarfs. We find that 60 per cent of white dwarfs must have a hydrogen mass larger than MH/MWD = 10−10, another 25 per cent have masses in the range MH/MWD = 10−14–10−10, and 15 per cent have less hydrogen than MH/MWD = 10−14. These results have implications for white dwarf asteroseismology, stellar evolution through the asymptotic giant branch and accretion of planetesimals on to white dwarfs.

Cunningham, Tim↗
DOE OSTI2021

Mixed Precision Fermi-Operator Expansion on Tensor Cores from a Machine Learning Perspective

Here we present a second-order recursive Fermi-operator expansion scheme using mixed precision floating point operations to perform electronic structure calculations using tensor core units. A performance of over 100 teraFLOPs is achieved for half-precision floating point operations on Nvidia’s A100 tensor core units. The second-order recursive Fermi-operator scheme is formulated in terms of a generalized, differentiable deep neural network structure, which solves the quantum mechanical electronic structure problem. We demonstrate how this network can be accelerated by optimizing the weight and bias values to substantially reduce the number of layers required for convergence. We also show how this machine learning approach can be used to optimize the coefficients of the recursive Fermi-operator expansion to accurately represent the fractional occupation numbers of the electronic states at finite temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Causes of and Solutions to Wind Speed Bias in NREL's 2020 Offshore Wind Resource Assessment for the California Pacific Outer Continental Shelf

This report provides the results of a detailed analysis into the causes of high wind speed bias in the 20-year wind resource data set for offshore California the National Renewable Energy Laboratory (NREL) released in 2020, herein called CA20. The data set was developed using the state-of-the-art Weather Research and Forecasting (WRF) model. Notably, no floating lidars were available at the time in offshore California to validate offshore hub-height wind speeds. In late 2020, the Pacific Northwest National Laboratory (PNNL) deployed two floating lidars in the California outer continental shelf (OCS), near the Bureau of Ocean Energy Management (BOEM) call areas of Humboldt and Morro Bay. Using these observations through 2021, NREL found considerable bias in modeled hub-height winds at both locations: up to +2 m/s at Humboldt over a 6-month period, and up to +1 m/s at Morro Bay over a one-year period. Upon the discovery of this bias, the Department of Energy (DOE) and BOEM funded NREL and PNNL to investigate the causes of, impacts of, and solutions to the bias in the CA20 data set. This report summarizes the findings of this research. We first investigated whether different WRF model setups could lead to reduced bias. We found that the choice of planetary boundary layer (PBL) scheme - which controls the vertical turbulent mixing of momentum, heat, and moisture in the lowermost part of the atmosphere - greatly affected hub-height wind speeds in the region. Specifically, switching from the Mellor-Yamada-Nakanishi-Niino (MYNN) scheme used in CA20 (and widely used across a range of operational and research weather models) to the less common Yonsei University (YSU) scheme nearly eliminated the bias at both the Humboldt and Morro Bay lidar locations. The large discrepancy between the MYNN- and YSU-modeled hub-height winds pointed towards the role of atmospheric stability. In general, PBL schemes agree well in conditions of high turbulence and mixing, normally referred to as "unstable" conditions. By contrast, PBL schemes start to diverge in "stable" conditions, where turbulence is low and thermal stratification (i.e., higher temperature air sitting on top of colder air) greatly suppresses vertical mixing. Under such conditions, winds aloft can decouple from surface effects and greatly accelerate, causing high wind speeds at hub-height and frequent low-level jets (LLJs). We determined that these stable conditions are in fact dominant in offshore California. The region is characterized by moderate-to-extreme stable stratification with a LLJ on average around 200 meters above sea-level. To our knowledge, no wind energy area globally has as strongly stable stratification as offshore California. Under these extreme conditions, we determined that the MYNN scheme models higher stability than YSU, resulting in less vertical turbulent mixing than YSU, allowing for the acceleration of hub-height winds, more intense LLJs, and higher-amplitude inertial oscillations. Using surface observations, we found that MYNN overestimates near-surface stability, whereas YSU tends to model stability better. We then considered several short-term case studies to assess additional meteorological drivers of the bias at Humboldt. We found that during synoptic scale northerly flows driven by the North Pacific High and inland thermal low, a coastal warm bias in the MYNN case studies contributes to the modeled wind speed bias by altering the boundary layer thermodynamics via a thermal wind mechanism. Given the strong performance of the YSU-based runs in offshore California, NREL has produced and published an updated version of the CA20 data set with YSU as the PBL scheme. This updated data set is now part of NREL's 2023 National Offshore Wind (NOW-23) data set, which covers all the U.S. offshore waters. The development and final validation of the NOW-23 data set in offshore California is documented in this report.

17 WIND ENERGY↗
DOE OSTI2020

Microscopy Studies of the Catalyst Inks for PEM Fuel Cells

The microstructure of the catalyst layer in proton exchange membrane fuel cells (PEMFC) is one of the key factors that determine fuel cell performance. The ink preparation, including dispersion solvent, mixing time, and mixing power, are among the less reported parameters that would influence the ionomer distribution on the catalyst surface and the continuity of the carbon network. In this work, novel characterization approaches have been used to investigate the effect of the Pt/C catalyst ink preparation conditions on the morphology and structures of the catalyst layer. Microscopy analysis revealed that longer mixing time led to better performing electrode structures than shorter mixing time. The longer mixing time enabled improved continuity of the ionomer network and high porosity in the cathode layer that contributes to improved proton conductivity and mass transport. This has been reflected in performance and durability tests, where the electrode made from a 5-day catalyst ink displayed improved performance compared to the one made from a 3-day ink. Durability studies showed 26% and 43% loss of the initial mass activity for 5 days and 3 days mixing, respectively. Finally, in addition, the catalyst layer prepared with ethylene glycol as the dispersion solvent showed better durability than water/1-propanol based solution.

25 ENERGY STORAGE↗
DOE OSTI2024

Contribution of expanded marine sulfur chemistry to the seasonal variability of dimethyl sulfide oxidation products and size-resolved sulfate aerosol

Marine emissions of dimethyl sulfide (DMS) and the subsequent formation of its oxidation products methanesulfonic acid (MSA) and sulfuric acid (H 2 SO 4 ) are well-known natural precursors of atmospheric aerosols, contributing to particle mass and cloud formation over ocean and coastal regions. Despite a long recognized and well-studied role in the marine troposphere, DMS oxidation chemistry remains a work in progress within many current air quality and climate models, with recent advances exploring heterogeneous chemistry and uncovering previously unknown intermediate species. With the identification of additional DMS oxidation path ways and intermediate species that influence the eventual fate of DMS, it is important to understand the impact of these pathways on the overall sulfate aerosol budget and aerosol size distribution. In this work, we update and evaluate the DMS oxidation mechanism of the chemical transport model GEOS-Chem by implementing expanded DMS oxidation pathways in the model. These updates include gas- and aqueous-phase reactions, the formation of the intermediates dimethyl sulfoxide (DMSO) and methanesulfinic acid (MSIA), and cloud loss and aerosol uptake of the recently quantified intermediate hydroperoxymethyl thioformate (HPMTF). We find that this updated mechanism collectively decreases the global mean surface-layer gas-phase sulfur dioxide (SO 2 ) mixing ratio by 40 % and enhances the sulfate aerosol ($SO^{2-}_{4}$) mixing ratio by 17 %. We further perform sensitivity analyses exploring the contribution of cloud loss and aerosol uptake of HPMTF to the overall sulfur budget. Comparing modeled concentrations to available observations, we find improved biases relative to previous studies. To quantify the impacts of these chemistry updates on global particle size distributions and the mass concentration, we use the TwO-Moment Aerosol Sectional (TOMAS) aerosol microphysics module coupled to GEOS-Chem and find that changes in particle formation and growth affect the size distribution of aerosol. With this new DMS-oxidation scheme, the global annual mean surface-layer number concentration of particles with diameters smaller than 80 nm decreases by 16.8 %, with cloud loss processes related to HPMTF being mostly responsible for this reduction. However, the global annual mean number of particles larger than 80 nm (corresponding to particles capable of acting as cloud condensation nuclei, CCN) increases by 3.8 %, suggesting that the new scheme promotes seasonal particle growth to these sizes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Effective medium approximation for the refractive index of stratified metal oxide composites synthesized by atomic layer deposition

Atomic layer deposition (ALD) is a unique method for synthesizing conformal layers with precise composition. It is especially useful for the synthesis of mixed metal oxides for functional materials. One application of interest is the use of ALD for tailoring the refractive index of coatings. In homogeneously distributed composites of metal oxides, the refractive properties can be approximated as the average of the indices of the components. This is known as an effective medium approximation (EMA) and can be used to design the macroscopic properties of composites. ALD produces layered, anisotropic films, so the validity of an EMA in describing these films is not clear. Here, we use optical simulations and experimental characterization of stratified composites of TiO 2 and Al 2 O 3 to study the application of an EMA to the transmission and reflection behavior of ALD-prepared mixed metal oxide thin films. We found that when the characteristic layer thickness is smaller than roughly 10 nm, the optical spectra of theoretical and experimental ALD films match the equivalent theoretical spectra for a material with a refractive index calculated from a simple, compositionally weighted EMA. Hence, this EMA could describe the transmission and reflectance spectra in ALD-derived TiO2–Al 2 O 3 nanolaminates when the films were sufficiently stratified even without thorough characterization of the real layers in the films. As a result, we demonstrated that ALD can be used to prepare effectively homogenous mixed metal oxide films with a predictable, tailorable refractive index of any value between those of the TiO 2 and Al 2 O 3 component materials.

42 ENGINEERING↗
DOE OSTI2023

Control of Host-Matrix Morphology Enables Efficient Deep-Blue Organic Light-Emitting Devices

Mixing a sterically bulky, electron-transporting host material into a conventional single host–guest emissive layer is demonstrated to suppress phase separation of the host matrix while increasing the efficiency and operational lifetime of deep-blue phosphorescent organic light-emitting diodes (PHOLEDs) with chromaticity coordinates of (0.14, 0.15). Here, the bulky host enables homogenous mixing of the molecules comprising the emissive layer while suppressing single host aggregation; a significant loss channel of nonradiative recombination. By controlling the amorphous phase of the host-matrix morphology, the mixed-host device achieves a significant reduction in nonradiative exciton decay, resulting in 120 ± 6% increase in external quantum efficiency relative to an analogous, single-host device. In contrast to single host PHOLEDs where electrons are transported by the host and holes by the dopants, both charge carriers are conducted by the mixed host, reducing the probability of exciton annihilation, thereby doubling of the deep-blue PHOLED operational lifetime. These findings demonstrate that the host matrix morphology affects almost every aspect of PHOLED performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Generalized Brunauer–Emmett–Teller Isotherm for Mixed-Gas Multilayer Adsorption Equilibria

Here, this work presents a rigorous thermodynamic framework to calculate mixed-gas multilayer adsorption equilibria from single-component isotherms and vapor–liquid equilibria. Named the generalized Brunauer–Emmett–Teller (gBET) isotherm, the newly formulated isotherm considers adsorbent surface heterogeneity, competitive adsorption on the monolayer, condensation–evaporation on the subsequent layers, and adsorbed phase nonideality for the monolayer and the subsequent layers. The monolayer adsorbed phase nonideality is tracked by using an area-based adsorption nonrandom two-liquid activity coefficient model. The adsorbed phase composition and corresponding nonideality in the subsequent layers are calculated at the dew point condition of the mixed gas with either an equation of state or an activity coefficient model for the vapor–liquid equilibria. The proposed model is validated with six single and three binary multilayer adsorption equilibrium systems, and the model results are compared against those from the classical BET isotherm for single-component adsorption and ideal adsorbed solution theory for mixed-gas adsorption equilibria.

09 BIOMASS FUELS↗
DOE OSTI2024

Simulating Mixed‐Phase Open Cellular Clouds Observed During COMBLE: Evaluation of Parameterized Turbulence Closure

Marine cold-air outbreaks, or CAOs, are airmass transformations whereby relatively cold boundary layer (BL) air is transported over relatively warm water. To more deeply understand BL and mixed-phase cloud properties during CAO conditions, the Cold-Air Outbreaks in the Marine Boundary Layer Experiment (COMBLE) took place from late 2019 into early 2020. During COMBLE, the U.S. Department of Energy's first Atmospheric Radiation Measurement Mobile Facility (AMF1) was deployed to Andenes, Norway, far downstream (~1,000 km) from the Arctic pack ice. This study examines the two most intense CAOs sampled at the AMF1 site. The observed BL structures are open cellular with high (~3–5 km) and cold (–30 to –50 °C) cloud tops, and they often have pockets of high liquid water paths (LWPs; up to ~1,000 g m –2 ) associated with strong updrafts and enhanced turbulence. We use a high-resolution mesoscale model to explore how well four turbulence closure methods represent open cellular clouds. After applying a radar simulator to model outputs for direct evaluation, cloud top properties agree well with AMF1 observations (within ~10%), but radar reflectivity and LWP agreement is more variable. Results suggest that the turbulent Prandtl number may play an important role for the simulated BL and cloud properties. All simulations produce enhanced precipitation rates that are well-correlated with a cloud transition. Finally, the eddy-diffusivity/mass-flux approach produces the deepest cloud layer and therefore the largest and most coherent cellular structures. Furthermore, we recommend the use of a non-local turbulence closure approach to better capture turbulent processes in intense CAOs.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Cost-effective Manufacturing and Morphological Stabilization of Nanostructured Cathodes for Commercial Solid Oxide Fuel Cells (SOFCs) [Slides]

The overall goals of the program were to develop methods for preparing and stabilizing SOFC electrodes by infiltration that can be manufactured on a practical scale, then transfer those methods to cells in stacks. Cathodes prepared by infiltration of nanoparticles into a porous scaffold of the electrolyte have demonstrated outstanding electrochemical performance and mechanical strength but are difficult to manufacture due to the large number of infiltration steps required to produce a conductive composite and show poor stability due to sintering of the nanoparticles. At Penn, the main goal was to develop a fabrication method that uses only a small number of infiltration steps. Infiltration with molten salts and electrodeposition were pursued but deemed impractical. A method in which an electronically conductive scaffold consisted of a composite of a mixed conductor, LSF (La 0.9 Sr 0.1 FeO 3 ), with yttria-stabilized zirconia (YSZ) was found to be promising. While some cation mixing between LSF and YSZ was observed during calcination, there was no evidence for new phases in XRD and incorporation of Zr into the perovskite could be minimized by reducing the Sr content of the LSF. To stabilize nanoparticles infiltrated into the LSF-YSZ composite scaffold, the USC team examined the effects of Atomic Layer Deposition with ZrO 2 and infiltrated nanoparticles. Significantly enhanced stability was observed with the infiltrated nanoparticles. The FuelCell Energy team prepared 4”x4” cells in which an LSF-YSZ composite scaffold was cofired with the YSZ electrolyte and infiltrated with LSCF nanoparticles. Apparently because the LSF-YSZ scaffold layer was very thin in this case, the cation mixing that occurred during calcination resulted in a poor scaffold-electrolyte interface which caused reduced performance.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Ambient pressure x-ray photoelectron spectroscopy study of water formation and adsorption under two-dimensional silica and aluminosilicate layers on Pd(111)

Ambient pressure x-ray photoelectron spectroscopy (AP-XPS) supported by density functional theory (DFT) calculations was used to characterize the interaction of water with two-dimensional (2D) silica and aluminosilicate bilayers on Pd(111). Starting with oxygen adsorbed at the SiO2/Pd interface, exposure to water caused the SiO 2 -derived XPS peaks to shift to higher binding energy and the removal of an O 1s feature associated with interfacial adsorbed oxygen. These observations were attributed to the formation of a mixed water–hydroxyl interface, which eliminates the interfacial dipolar layer, and its associated electrostatic potential, created by adsorbed oxygen. Interfacial oxygen also reacted with H 2 to produce adsorbed water which also caused an upward binding energy shift of the SiO 2 peaks. Spectra recorded under 0.5 Torr water revealed additional water adsorption and a further shift of the overlayer peaks to higher binding energy. Incorporating Al into the 2D material caused the bilayer peaks to shift to lower binding energy which could be explained by electron donation from the metal to the bilayer. Although the stronger interaction between the bilayer and Pd substrate should restrict interfacial adsorption and reaction, similar trends were observed for water and hydrogen exposure to interfacial adsorbed oxygen. Less water adsorption was observed at the aluminosilicate interface which is a consequence of Al strengthening the bond to the metal substrate. The results reveal how the sensitivity of XPS to interfacial dipoles can be exploited to distinguish reactions taking place in confined spaces under 2D layers and how tuning the composition of the 2D layer can impact such reactions.

Density functional theory↗