Search NASA⌕ Search

SEARCH · Search NASA

Results for “Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Structure-Property Relationships of Bismaleimides

The purpose of this research was to control and systematically vary the network topology of bismaleimides through cure temperature and chemistry (addition of various coreactants) and subsequently attempt to determine structure-mechanical property relationships. Characterization of the bismaleimide structures by dielectric, rheological, and thermal analyses, and density measurements was subsequently correlated with mechanical properties such as modulus, yield strength, fracture energy, and stress relaxation. The model material used in this investigation was 4,4'-BismaleiMidodIphenyl methane (BMI). BMI was coreacted with either 4,4'-Methylene Dianiline (MDA), o,o'-diallyl bisphenol A (DABA) from Ciba Geigy, or Diamino Diphenyl Sulfone (DDS). Three cure paths were employed: a low- temperature cure of 140 C where chain extension should predominate, a high-temperature cure of 220 C where both chain extension and crosslinking should occur simultaneously, and a low-temperature (140 C) cure followed immediately by a high-temperature (220 C) cure where the chain extension reaction or amine addition precedes BMI homopolymerization or crosslinking. Samples of cured and postcured PMR-15 were also tested to determine the effects of postcuring on the mechanical properties. The low-temperature cure condition of BMI/MDA exhibited the highest modulus values for a given mole fraction of BMI with the modulus decreasing with decreasing concentration of BMI. The higher elastic modulus is the result of steric hindrance by unreacted BMI molecules in the glassy state. The moduli values for the high- and low/high-temperature cure conditions of BMI/MDA decreased as the amount of diamine increased. All the moduli values mimic the yield strength and density trends. For the high-temperature cure condition, the room- temperature modulus remained constant with decreasing mole fraction of BMT for the BMI/DABA and BMI/DDS systems. Postcuring PMR-15 increases the modulus over that of the cured material even though density values of cured and postcured PMR were essentially the same. Preliminary results of a continuous and intermittent stress relaxation experiment for BMI:MDA in a 2:1 molar ratio indicate that crosslinking is occurring when the sample is in the undeformed state. Computer simulation of properties such as density, glass transition temperature, and modulus for the low- temperature cure conditions of BMI/MDA and BMI/DABA were completed. The computer modeling was used to help further understand and confirm the structure characterization results. The simulations correctly predicted the trends of these properties versus mole fraction BMI and were extended to other BMI/diamine systems.

Tenteris-Noebe, Anita D.↗

COMPARISON OF ELASTIC OF POROUS CORDIERITE BY FLEXURE AND DYNAMIC TEST METHODS

Previous work showed differences in apparent elastic modulus between mechanical flexure testing and resonance methods. Flexure tests have been conducted using non-contact optical systems to directly measure deflection for calculation of elastic modulus. Dynamic test methods for elastic modulus measurement were conducted on the same material for comparison. The results show significant difference in the apparent elastic modulus for static flexure versus dynamic methods. The significance of the difference in apparent elastic modulus on thermal stress and the hypotheses for these differences will be discussed. Dynamic measurement (resonance) and static measurement (mechanical) produce different values for elastic modulus of porous cordierite ceramic. The elastic modulus from resonance is a measure of the material response at very low strain which is different from the material response in a mechanical test with relatively large strain. The apparent elastic moduli for dynamic versus static test methods in this study are different by a factor of two. This result has significant impact on calculated stress and life in an aftertreatment component.

36 MATERIALS SCIENCE↗

Atomistic Simulations of the Elastic Compression of Platinum Nanoparticles

Abstract The elastic behavior of nanoparticles depends strongly on particle shape, size, and crystallographic orientation. Many prior investigations have characterized the elastic modulus of nanoscale particles using experiments or simulations; however their reported values vary widely depending on the methods for measurement and calculation. To understand these discrepancies, we used classical molecular dynamics simulation to model the compression of platinum nanoparticles with two different polyhedral shapes and a range of sizes from 4 to 20 nm, loaded in two different crystal orientations. Multiple standard methods were used to calculate the elastic modulus from stress-vs-strain data for each nanoparticle. The magnitudes and particle-size dependence of the resulting moduli varied with calculation method and, even for larger nanoparticles where bulk-like behavior may be expected, the effective elastic modulus depended strongly on shape and orientation. Analysis of per-atom stress distributions indicated that the shape- and orientation-dependence arise due to stress triaxiality and inhomogeneity across the particle. When the effective elastic modulus was recalculated using a representative volume element in the center of a large nanoparticle, the elastic modulus had the expected value for each orientation and was shape independent. It is only for single-digit nanoparticles that meaningful differences emerged, where even the very center of the particle had a lower modulus due to the effect of the surface. These findings provide better understanding of the elastic properties of nanoparticles and disentangle geometric contributions (such as stress triaxiality and spatial inhomogeneity) from true changes in elastic properties of the nanoscale material.

36 MATERIALS SCIENCE↗

The cosmological moduli problem and naturalness

Nowadays, the cosmological moduli problem (CMP) comes in three parts: 1. potential violation of Big-Bang nucleosynthesis (BBN) constraints from late decaying moduli fields, 2. the moduli-induced gravitino problem wherein gravitinos are overproduced and their decays violate BBN or dark matter overproduction bounds and 3. the moduli-induced lightest SUSY particle (LSP) overproduction problem. Also, the CMP may be regarded as either a problem or else a solution to scenarios with dark matter over- or under-production. We examine the cosmological moduli problem and its connection to electroweak naturalness. We calculate the various two-body decay widths of a light modulus field into MSSM particles and gravitinos within general supersymmetric models. We include both phase space and mixing effects. We examine cases without and with helicity suppression of modulus decays to gravitinos (cases 1 & 2) and/or gauginos (cases A & B). For case B1, we evaluate regions of gravitino mass m 3/2 vs. modulus mass mΦ parameter space constrained by BBN, by overproduction of gravitinos and by overproduction of neutralino dark matter, along with connections to naturalness. For this case, essentially all of parameter space is excluded unless mΦ ≳ 2.5 × 10 3 TeV with mΦ< 2m 3/2 For a potentially most propitious case B2 with Φ decay to Higgs and matter turned off, then modulus branching fractions to SUSY and to gravitinos become highly suppressed at large m Φ . But since the modulus number density increases faster than the branching fractions decrease, there is still gross overproduction of neutralino dark matter. We also show that in this scenario the thermally produced gravitino problem is fixed by huge entropy dilution, but non-thermal gravitino production from moduli decay remains a huge problem unless it is kinematically suppressed with m Φ < 2m 3/2 . In a pedagogical appendix, we present detailed calculations of modulus field two-body decay widths.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Effect of Nb Content on Microstructures and Mechanical Properties of Ti-xNb-2Fe Alloys

β-Type Ti-Nb-based alloys exhibit satisfactory biocompatibility and low Young’s modulus for biomedical applications. The microstructure and mechanical properties of a series of Ti-(14, 16, 18, 20, 22, 24)Nb-2Fe alloys fabricated by arc melting were investigated by XRD, optical microscopy, and tensile tests. Both ω and α″ phases existed in the Ti-14Nb-2Fe alloy, while just a single β phase existed in the other alloys. Twinning is an important deformation mechanism that causes work hardening and twinning-induced plasticity. It was found in the Ti-(14, 16, 18, 20)Nb-2Fe alloys and not in the Ti-22Nb-2Fe alloy. The Ti-14Nb-2Fe alloy exhibited the highest tensile strength and the highest Young’s modulus owing to the existence of the ω phase. The tensile strength decreased gradually from 830 MPa (highest) for the Ti-14Nb-2Fe alloy to 540 MPa (lowest) for the Ti-24Nb-2Fe alloy with an increase in the Nb content. The Young’s modulus decreased from 90 GPa for the Ti-14Nb-2Fe alloy to 63 GPa for the Ti-22Nb-2Fe alloy and then increased to 71 GPa for the Ti-24Nb-2Fe alloy. Elongation shows the same trend as the Young’s modulus. The Ti-22Nb-2Fe alloy, with a low Young’s modulus of 63 GPa, tensile strength of 570 MPa, and 15% elongation, was found suitable for biomedical applications. The Ti-20Nb-2Fe alloy also exhibits a high tensile strength, a Young’s modulus ratio of 9.24 × 10{sup −3}, and 18% elongation and is thus considered another valuable Ti alloy for biomedical applications.

36 MATERIALS SCIENCE↗

Elaborating the phases and mechanical properties of multiphase alloy: Experimental two-dimensional mapping combined with theoretical calculations

Highlights: • Mechanical modulus and hardness distribution mapping is obtained for the first time by NanoBlitz 3D. • Phases mapping and exact element ratio are characterized for the nano multielement carbides by EPMA. • Carbides types are confirmed by acid etching and XRD refinement. • Young's modulus of multiple carbides is verified by DFT calculations and Voigt-Reuss-Hill model. - Abstract: The relationship between types of phases, microstructure and mechanical properties is always a critical challenge for the research and application of multiphase alloys. We report for the first time that NanoBlitz 3D method implemented in iNano is used to investigate the distribution of micro mechanical modulus and hardness for the entire complex multiphase alloy Fe-6.0W-5.0Mo-4.0Cr-2.0V-0.83C by constructing the two-dimensional mapping. In order to build the correlation between the microstructure and properties, the carbides in this tempering state steel are confirmed to be Fe{sub 3}(W, Mo){sub 3}C, Cr{sub 15.58}Fe{sub 7.42}C{sub 6} and V{sub 8}C{sub 7} by acid etching and XRD refinement. The phases mapping is obtained by electron probe micro-analysis. Exact element ratio is characterized for the nano-scale multielement carbides precipitates. The Young's modulus and hardness of the precipitated carbides are up to 330 GPa and 22 GPa, respectively. The distribution range of Young's modulus and hardness is during 150 to 250 GPa and 2.5 to 7.0 GPa for the matrix phases, respectively. The experimental Young's modulus and hardness results are verified by first-principles calculations combined with Voigt-Reuss-Hill approximation. In fact, this work provides a successful demonstration to three-dimensionally characterize the micro mechanical properties for all the ceramics and alloys.

36 MATERIALS SCIENCE↗

Dielectric relaxation of gamma irradiated muscovite mica

Highlights: • The present article reports the effect of gamma irradiation on the dielectric relaxation characteristics of muscovite mica. • Dielectric and electrical relaxations have been analyzed in the framework of dielectric permittivity, electric modulus and Cole–Cole formalisms. • The frequency dependent electrical conductivity has been rationalized using Johnsher’s universal power law. • The experimentally measured electric modulus and conductivity data have been fitted using Havriliak–Negami dielectric relaxation function. - Abstract: In the present research, the dielectric relaxation of gamma irradiated muscovite mica was studied in the frequency range of 0.1 Hz–10 MHz and temperature range of 653–853 K, using the dielectric permittivity, electric modulus and conductivity formalisms. The dielectric constants (ϵ′ and ϵ′′) are found to be high for gamma irradiated muscovite mica as compared to the pristine sample. The frequency dependence of the imaginary part of complex electric modulus (M′′) and dc conductivity data conforms Arrhenius law with single value of activation energy for pristine sample and two values of activation energy for gamma irradiated mica sample. The experimentally assessed electric modulus and conductivity information have been interpreted by the Havriliak–Negami dielectric relaxation explanation. Using the Cole–Cole framework, an analysis of real and imaginary characters of the electric modulus for pristine and gamma irradiated sample was executed which reflects the non-Debye relaxation mechanism.

36 MATERIALS SCIENCE↗

Elastic Properties across the y→α Volume Collapse in Cerium versus Pressure and Temperature

Here, the longitudinal and transverse sound speeds, c L and c T , of polycrystalline cerium were measured isothermally vs pressure up to the critical temperature across the iso-structural γ-α volume collapse (VC) phase transition. We deduce values for the adiabatic bulk modulus BS, the shear modulus G = ρc T 2 , the Poisson’s ratio ν and the Debye temperature, θ D (p). We find that the elastic constant C 12 is solely responsible for the decrease of B S with pressure towards the VC at RT. With increasing temperature, the lattice contribution ΔS vib (γ→α) to the total entropy change across the VC decreases more rapidly to zero than the total entropy itself suggesting that another mechanism, possibly disorder, assists in stabilizing the γ-phase entropically against the α-phase. Also, with increasing temperature, the Poisson’s ratio becomes negative near the VC transition, meaning that cerium metal takes on auxetic characteristics over a small pressure range. At the critical point the Poisson’s ratio ought to be -1, since the isothermal bulk modulus vanishes and the shear modulus remains nonzero.

36 MATERIALS SCIENCE↗

Spectral asymmetry of the massless Dirac operator on a 3-torus

Consider the massless Dirac operator on a 3-torus equipped with Euclidean metric and standard spin structure. It is known that the eigenvalues can be calculated explicitly: the spectrum is symmetric about zero and zero itself is a double eigenvalue. The aim of the paper is to develop a perturbation theory for the eigenvalue with smallest modulus with respect to perturbations of the metric. Here the application of perturbation techniques is hindered by the fact that eigenvalues of the massless Dirac operator have even multiplicity, which is a consequence of this operator commuting with the antilinear operator of charge conjugation (a peculiar feature of dimension 3). We derive an asymptotic formula for the eigenvalue with smallest modulus for arbitrary perturbations of the metric and present two particular families of Riemannian metrics for which the eigenvalue with smallest modulus can be evaluated explicitly. We also establish a relation between our asymptotic formula and the eta invariant.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ab initio study of anisotropic mechanical properties of LiCoO{sub 2} during lithium intercalation and deintercalation process

The mechanical properties of Li{sub x}CoO{sub 2} under various Li concentrations and associated anisotropy have been systematically studied using the first principles method. During the lithium intercalation process, the Young's modulus, bulk modulus, shear modulus, and ultimate strength increase with increasing lithium concentration. Strong anisotropy of mechanical properties between a-axis and c-axis in Li{sub x}CoO{sub 2} is identified at low lithium concentrations, and the anisotropy decreases with increasing lithium concentration. The observed lithium concentration dependence and anisotropy are explained by analyzing the charge transfer using Bader charge analysis, bond order analysis, and bond strength by investigating partial density of states and charge density difference. With the decrease of Li concentration, the charge depletion in the bonding regions increases, indicating a weaker Co-O bond strength. Additionally, the Young's modulus, bulk modulus, shear modulus, and toughness are obtained by simulating ab initio tensile tests. From the simulated stress-strain curves, Li{sub x}CoO{sub 2} shows the highest toughness, which is in contraction with Pugh criterion prediction based on elastic properties only.

36 MATERIALS SCIENCE↗

Temperature Dependent Elastic moduli of Lead-Telluride based Thermoelectric Materials

In the open literature, reports of mechanical properties are limited for semiconducting thermoelectric materials, including the temperature dependence of the elastic moduli. In this study, for both cast ingots and hot pressed billets of Ag-, Sb-, Sn-, and S- doped PbTe thermoelectric materials, Resonant Ultrasound Spectroscopy (RUS) was utilized to determine the temperature dependence of elastic moduli including Young's modulus, shear modulus, and Poisson's ratio. This study is the first to determine the temperature-dependent elastic moduli for these PbTe based thermoelectrics and among the few determinations of elasticity of any thermoelectric material for temperatures above 300 K. The Young s modulus and Poisson s ratio measured from room temperature to 773 K during heating and cooling agreed well. Also, the observed Young s modulus, E, versus temperature, T, relationship E(T) = E0(1 bT) is consistent with predictions for materials in the range well above the Debye temperature. A nanoindentation study of Young s modulus on the specimen faces showed that both the cast and hot pressed specimens were approximately elastically isotropic.

36 MATERIALS SCIENCE↗

Phenomenological aspects of no-scale inflation models

We discuss phenomenological aspects of inflationary models wiith a no-scale supergravity Kähler potential motivated by compactified string models, in which the inflaton may be identified either as a Kähler modulus or an untwisted matter field, focusing on models that make predictions for the scalar spectral index n{sub s} and the tensor-to-scalar ratio r that are similar to the Starobinsky model. We discuss possible patterns of soft supersymmetry breaking, exhibiting examples of the pure no-scale type m{sub 0} = B{sub 0} = A{sub 0} = 0, of the CMSSM type with universal A{sub 0} and m{sub 0} ≠ 0 at a high scale, and of the mSUGRA type with A{sub 0} = B{sub 0} + m{sub 0} boundary conditions at the high input scale. These may be combined with a non-trivial gauge kinetic function that generates gaugino masses m{sub 1/2} ≠ 0, or one may have a pure gravity mediation scenario where trilinear terms and gaugino masses are generated through anomalies. We also discuss inflaton decays and reheating, showing possible decay channels for the inflaton when it is either an untwisted matter field or a Kähler modulus. Reheating is very efficient if a matter field inflaton is directly coupled to MSSM fields, and both candidates lead to sufficient reheating in the presence of a non-trivial gauge kinetic function.

79 ASTRONOMY AND ASTROPHYSICS↗

Thermal Equation of State of Rhenium Diboride by High Pressure-Temperature Synchrotron X-ray Studies

The unit-cell volume of rhenium diboride (ReB{sub 2}) has been measured by synchrotron X-ray diffraction at pressures and temperatures of up to 7.5 GPa and 1100 K with a cubic anvil apparatus. From the pressure (P)-volume (V)-temperature (T) measurements, thermoelastic parameters were derived for ReB2 based on a modified high-T Birch-Murnaghan equation of state and a thermal-pressure approach. With the pressure derivative of the bulk modulus, K{sub O{prime}}, fixed at 4.0, we obtain: the ambient bulk modulus K{sub O}=334(23)GPa, temperature derivative of bulk modulus at constant pressure ({delta}K/{delta}T){sub P}=0.064(6)GPaK{sup -1}, volumetric thermal expansivity {alpha}{sub T}(K{sup -1})=a+bT with a=1.33(25)x10{sup -5}K{sup -1} and b=1.48(64)x10 8K 2, pressure derivative of thermal expansion ({delta}{alpha}/{delta}P){sub T}=5.76(95)x10{sup -7}GPa{sup -1}K{sup -1}and temperature derivative of bulk modulus at constant volume ({delta}K/{delta}T){sub v}=0.049(11) GPaK{sup -1}. The ambient bulk modulus derived from this work is comparable to previous experimental and theoretical results. These results, including the ambient bulk modulus and other thermoelastic parameters determined in present study, extend our knowledge of the fundamental thermophysical properties on ReB{sub 2} and are important to the development of theoretical and computational modelings of hard materials.

43 PARTICLE ACCELERATORS↗

Temperature dependence of mechanical stiffness and dissipation in ultrananocrystalline diamond films grown by the HFCVD techinque.

We have characterized mechanical properties of ultrananocrystalline diamond (UNCD) thin films grown using the hot filament chemical vapor deposition (HFCVD) technique at 680 C, significantly lower than the conventional growth temperature of -800 C. The films have -4.3% sp{sup 2} content in the near-surface region as revealed by near edge x-ray absorption fine structure spectroscopy. The films, -1 {micro}m thick, exhibit a net residual compressive stress of 370 {+-} 1 MPa averaged over the entire 150 mm wafer. UNCD microcantilever resonator structures and overhanging ledges were fabricated using lithography, dry etching, and wet release techniques. Overhanging ledges of the films released from the substrate exhibited periodic undulations due to stress relaxation. This was used to determine a biaxial modulus of 838 {+-} 2 GPa. Resonant excitation and ring-down measurements in the kHz frequency range of the microcantilevers were conducted under ultrahigh vacuum (UHV) conditions in a customized UHV atomic force microscope system to determine Young's modulus as well as mechanical dissipation of cantilever structures at room temperature. Young's modulus is found to be 790 {+-} 30 GPa. Based on these measurements, Poisson's ratio is estimated to be 0.057 {+-} 0.038. The quality factors (Q) of these resonators ranged from 5000 to 16000. These Q values are lower than theoretically expected from the intrinsic properties of diamond. The results indicate that surface and bulk defects are the main contributors to the observed dissipation in UNCD resonators.

36 MATERIALS SCIENCE↗

Intermediate-Term Thermal Aging Effect Evaluation for Grade 92 and 316L at The LWR Relevant Temperature

Life extension of the existing nuclear reactors imposes accumulated damages, such as higher fluences and longer period of corrosion, to structural materials, which would result in significant challenges to the traditional reactor materials such as type 304 and 316 stainless steels. Advanced alloys with superior radiation resistance will increase safety margins, design flexibility, and economics for not only the life extension of the existing fleet but also new builds with advanced reactor designs. The Electric Power Research Institute (EPRI) teamed up with Department of Energy (DOE) on the Advanced Radiation Resistant Materials (ARRM) program, aiming to develop and test degradation resistant alloys from current commercial alloy specifications by 2021 to a new advanced alloy with superior degradation resistance in light water reactor (LWR)-relevant environments by 2024. Based on a comprehensive microstructure and property screening performed in Phase-1 of the ARRM program, a total of five alloys, together with 316L and X-750 as references, were down-selected for Phase-2 neutron irradiation studies. Because thermal aging could exert a synergistic effect on neutron irradiation due to the low neutron damage rate on the order of 10 –7 displacements per atom per second (dpa/s), Grade 92 (one of the five down-selected alloys) and two heats of 316L were selected in this task to study the effect of aging at 350°C for 12.5–12.7 kh on microstructure and mechanical properties. The aging time is approximately corresponding to 5 dpa neutron irradiation, which can be served as a reference for the 5-dpa-irradiated samples of the alloys to help understand the independent neutron damage influence on microstructure and mechanical properties. Optical microscopy and scanning electron microscopy were used for microstructural characterization. Hardness, tensile, Charpy impact toughness, and fracture toughness in the ductile regime of the aged samples were examined. The aging of Grade 92 led to the formation of many Laves phase in sizes of ~100–200 nm and resulted in some reduction in hardness and yield/ultimate tensile strength with some increases in uniform and total plastic elongations, which may have helped the enhancement of Charpy impact toughness, e.g., ~4 J increase in upper-shelf energy and 20.5°C reduction in ductile-brittle transition temperature compared with the unaged condition. The fracture toughness of the aged Grade 92 showed decent toughness of ~303 MPa√m (K Jq ) with ~87 tearing modulus at 22°C, which reduced to ~241 MPa√m (~20% reduction) with ~75 tearing modulus at 300°C. The two heats of 316L are differentiated by their amounts of δ-ferrite, i.e., ~1 vol% in heat T1103 and ~4 vol% in heat N5B8. The two heats of 316L were subjected to 15% cold work (CW) as this condition is often used in nuclear reactors to help trapping radiation-induced defects and thus postpone the steady state swelling stage. The aging did not result in any noticeable microstructure changes, except for possible segregations at grain boundaries that need to be further investigated. The aging resulted in slight reduction in hardness of 316L-T1103 and slight increase in hardness of 316L-N5B8, which is consistent with their tensile testing results. The 15%CW might have introduced some inhomogeneity, resulting in large standard deviations in hardness, which were reduced after the aging. The aged 316L followed the same trend as the unaged condition for the strength and elongation results from the tensile testing. Minimum elongations appeared within ~300–600°C, above which the elongations seem to increase. Unlike the negligible or minor changes in microstructure, hardness and tensile results of the two heats of 316L, their fracture toughness showed noticeable difference. The aged 316L-T1103 showed good toughness of ~350 MPa√m with ~80 tearing modulus at 22°C, which reduced to ~271 MPa√m (~23% reduction) with ~83 tearing modulus at 300°C. In contrast, the aged 316L-N5B8 showed lower toughness of ~244 MPa√m with ~53 tearing modulus at 22°C, which reduced to ~180 MPa√m (~26% reduction) with ~31 tearing modulus at 300°C. The preliminary results indicate that the presence of high volume of δ-ferrite would noticeable impair fracture toughness although it may not influence hardness and tensile properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

HTV Post Irradiation Examination (PIE) Results and Analysis

This report is responsive to 2017 Idaho National Laboratory (INL) Memorandum Purchase Order No. 00181805, statement of work 13687 “HTR Graphite R&D – FY ORNL 2017 MPO”, Deliverable 12A “issue final report on the HTV PIE to INL”, due June 15 th 2017.The HTV (High Temperature Vessel) was a HFIR (High Flux Isotope Reactor) high temperature target rod capsule in support of the DOE’s (Department of Energy) High Temperature Reactor (HTR) program. The HTV capsule contained eight sub-capsules, each with nine graphite specimens. The sub-capsules were designed to operate at ~900°C, ~1200°C or ~1600°C. The actual irradiation temperature was established by interrogating SiC and graphite TMs during PIE (post-irradiation examination. The capsule dose ranged from 1.49 dpa to 3.34 dpa, and varied with specimen position within the capsule the maximum dose occurring at the reactor mid-plane and the minimum dose occurring at the core periphery. The irradiated graphite specimens were examined during PIE to establish their high temperature dimensional and elastic (Young’s) modulus changes. The PIE results are reported and analyzed here. The dimensional and modulus changes were shown to have a strong thermal dependence. The dimensional changes were small, being of the order of a few percent or less, ranging from a maximum shrinkage of -3.1% (PCEA WG, T irr =1500°C at 3.3 dpa) to +0.131% (2114 AG, T irr = 869 at 3.2 dpa). The specimen volume shrinkages varied from –0.81 (2114, T irr = 840 at 3.1 dpa) to -9.15% (PCEA, T irr =1500°C at 3.3 dpa). The volume changes were larger at higher Irradiation temperatures. Of the six grades examined, only 2114 moved into the net positive dimensional swelling situation. Significantly, the volume change for 2114 remained negative at the doses and temperature tested here. Dimensional and volume changes were explained in terms of the temperature dependence of the crystal growth rate, the anisotropy of the crystal growth (crystallographic c-axis growth and crystallographic a-direction shrinkage) and the thermal closure of aligned micro-porosity. The modulus changes were much larger, being of the order of a few tens of percent. A trend of lesser fractional increases of Young’s Modulus with an increasing T irr was noted. The minimum increase in Young’s Modulus was 20% (H-451 WG, T irr =1500°C at 3.3 dpa) and the maximum 71% (IG-110, T irr = 840(actual) at 3.3 dpa). The rise in Young’s modulus is attributed to dislocation pinning by lattice defects produced by neutron irradiation and the temperature dependency is related to the irradiation temperature influence on the number of defect available to pin dislocations.

36 MATERIALS SCIENCE↗

Elastic constant versus temperature behavior of three hardened maraging steels

Elastic constants of three maraging steels were determined by measuring ultrasonic velocities. Annealed steels show slightly lower bulk moduli and considerably lower shear moduli than hardened steels. All the elastic constants (Young's modulus, shear modulus, bulk modulus and Poisson's ratio) show regular temperature behavior between 76 and 400 K. Young's modulus and the shear modulus increase with increasing yield strength, but the bulk modulus and Poisson's ratio are relatively unchanged. Elastic anisotropy is quite small.

Ledbetter, H. M.↗

Adhesion in ceramics and magnetic media

When a ceramic is brought into contact with a metal or a polymeric material such as a magnetic medium, strong bonds form between the materials. For ceramic-to-metal contacts, adhesion and friction are strongly dependent on the ductility of the metals. Hardness of metals plays a much more important role in adhesion and friction than does the surface energy of metals. Adhesion, friction, surface energy, and hardness of a metal are all related to its Young's modulus and shear modulus, which have a marked dependence on the electron configuration of the metal. An increase in shear modulus results in a decrease in area of contact that is greater than the corresponding increase in surface energy (the fond energy) with shear modulus. Consequently, the adhesion and friction decrease with increasing shear modulus. For ceramics in contact with polymeric magnetic tapes, environment is extremely important. For example, a nitrogen environment reduces adhesion and friction when ferrite contacts polymeric tape, whereas a vacuum environment strengthens the ferrite-to-tape adhesion and increases friction. Adhesion and friction are strongly dependent on the particle loading of the tape. An increase in magnetic particle concentration increases the complex modulus of the tape, and a lower real area of contact and lower friction result.

Miyoshi, Kazuhisa↗