Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Impact of low reactivity fuel type on low load combustion, emissions, and cyclic variations of diesel-ignited dual fuel combustion

In this study, cyclic variations in dual fuel combustion with diesel ignition of three different low reactivity fuels (methane, propane, and gasoline) are examined under identical operating conditions. Experiments were performed on a single cylinder research engine (SCRE) at a low load of 3.3 bar brake mean effective pressure (BMEP). The start of injection (SOI) of diesel was varied from 280 to 330 absolute crank angle degrees (CAD). Engine speed, rail pressure, and boost pressure were held constant at 1500 rpm, 500 bar, and 1.5 bar, respectively. The energy substituted by the low reactivity fuel was fixed at 80% of the total energy input. It was found that diesel-methane (DM) and diesel-propane (DP) combustion were affected by diesel mixing to a greater extent than diesel-gasoline (DG) combustion due to the higher reactivity of gasoline. The magnitude of low temperature heat release was greatest for DG combustion followed by DM and DP combustion for all SOIs. The ignition delay for DG combustion was the shortest, followed by DM and DP combustion. DM and DP combustion exhibited more cyclic variations than DG combustion. Cyclic variations decreased for DM and DP combustion when SOI was advanced; however, DG combustion cyclic variations remained essentially constant for all SOIs. Earlier SOIs (280, 290, 300, and 310 CAD) for DM and (280, 290, and 300 CAD) for DP combustion indicated some prior-cycle effects on the combustion and IMEP (i.e. some level of determinism).

Engineering↗

Simulation of subnanosecond streamers in atmospheric-pressure air: Effects of polarity of applied voltage pulse

Results of simulation of subnanosecond streamer propagation in corona gap configuration, obtained in the framework of 2D fluid model, are presented. Effects related with the polarity of a voltage pulse applied to the stressed electrode are discussed. It is argued that these effects (dependence of the discharge current and propagation velocity on the polarity of applied voltage) observed in experiments can be attributed to the difference in initial (preceding the streamer formation) distributions of charged species inside the gap. This difference can be caused by preionization (at negative polarity) of the gas inside the discharge gap by runaway electrons. Calculated streamers have large widths (up to 1 cm) and move with velocities in the range of 10{sup 9}–10{sup 10 }cm s{sup −1}, similar to experimental data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Analytical study of a gas of gluonic quasiparticles at high temperature: Effective mass, pressure, and trace anomaly

The thermodynamical properties of a pure Yang-Mills theory SU(N) is described by a gas of gluonic quasiparticles with temperature-dependent mass m(T) and a bag function B(T). The analytic behavior of m(T) and the pressure p in the temperature range 2.5-5T{sub c} are derived and constraints on the parameters defining B(T) are discussed. The trace anomaly {theta}={rho}-3p is evaluated in the high T domain: it is dominated by a quadratic behavior {theta}=nKT{sup 2}, where n=2(N{sup 2}-1) is the number of degrees of freedom and K is an integration constant which does not depend on the bag function B(T). The quadratic rise of {theta} is in good agreement with recent lattice simulations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Pressure-temperature effects on knock with iso-octane and propane at various compression ratios and intake temperatures

Knock remains one of the main limitations for increased internal combustion engine efficiency. Recent trends in light-duty vehicles towards downsized, boosted engines increases the need for improving the understanding between fuel chemistry and thermodynamic effects contributing to knock. Previous studies have shown the importance of end-gas thermodynamic conditions on knock onset and behavior, with relationships to fuel chemistry illustrated. However, a complete understanding of how fuels allow access to higher engine loads and the governing physics behind end-gas knock under a wide range of thermodynamic conditions is still unclear. Experiments in this work improve this understanding with the use of three fuels (1) iso-octane, a low octane sensitivity (OS) fuel (2) a Co-Optima aromatic core fuel, which has similar research octane number (RON) yet significantly higher OS, and (3) propane, known for its knock resistance. Engine load sweeps are conducted with each fuel while maintaining a CA50 of 8 crank angle degrees after top dead center (°CA aTDCf). As load increases and knock onset is observed, spark is delayed to its knock limited spark advance (KLSA) allowing further increases in load until either one of two limits is reached; (1) CA50 retard limit (2) Peak cylinder pressure limit. Experiments are conducted at 40°C and 90°C intake temperature and at two distinct compression ratios (rc) 9.2:1 and 13.6:1. Two-zone zero-dimensional simulations were performed in Chemkin to extract end-gas pressure and temperature conditions through the combustion process for each experimental condition of interest. CA50 response as a function of engine load is compared for all experimental conditions and fuels, and a pressure-temperature (PT) trajectory analysis is conducted using constant volume ignition delay contours to explain the behavior of each fuel.

Dal Forno Chuahy, Flavio↗

Development of a medium-duty stoichiometric diesel micro-pilot natural gas engine

Fueling a compression-ignition engine with premixed natural gas offers the potential to combine a clean-burning, low-carbon fuel with a high compression ratio, high-efficiency engine. This work describes the development of a multi-cylinder 6.7 L diesel engine converted to run stoichiometric diesel micro-pilot/ natural gas premix combustion with a maximum diesel contribution target of 5% of the total fuel energy and a three-way catalyst aftertreatment system. Results are given by comparing the stoichiometric combustion to the diesel baseline operation, showing combustion characteristics differences, including the rapid two stage heat release. A high load output of 23 bar brake mean effective pressure was obtained with diesel-like brake thermal efficiency of 41%. This operating condition enabled a brake specific CO 2 emissions reduction of up to 25% when compared to diesel. It was observed that the low load output is limited by combustion stability when operated at stoichiometric condition. The three-way catalyst is observed to run at peak efficiency with an equivalence ratio of 1.01. Injector fouling was observed through the inspection of the nozzle and its internal parts, indicating carbon build-up similar to that seen in injector coking mechanisms. A comparison of the developed engine to other engine technologies is given, showing that the diesel micro-pilot natural gas engine performance is in good standing among other diesel and gas engines in the market.

Engineering↗

Influence of charge motion and compression ratio on the performance of a combustion concept employing in-cylinder gasoline and natural gas

The present paper represents a small piece of an extensive experimental effort investigating the dual-fuel operation of a light-duty spark ignited engine. Natural gas (NG) was directly injected into the cylinder and gasoline was injected into the intake-port. Direct injection (DI) of NG was used in order to overcome the power density loss usually experienced with NG port-fuel injection (PFI) as it allows an injection after intake valve closing. Having two separate fuel systems allows for a continuum of in-cylinder blend levels from pure gasoline to pure NG operation. The huge benefit of gasoline is its availability and energy density, whereas NG allows efficient operation at high load due to improved combustion phasing enabled by its higher knock resistance. Furthermore, using NG allowed a reduction of carbon dioxide emissions across the entire engine map due to the higher hydrogen-to-carbon ratio. Exhaust gas recirculation (EGR) was used to (a) increase efficiency at low and part-load operation and (b) reduce the propensity of knock at higher compression ratios (CRs) thereby enabling blend levels with greater amount of gasoline across a wider operating range. Two integral engine parameters, CR and in cylinder turbulence levels, were varied in order to study their influence on efficiency, emissions, and performance over a specific speed and load range. Increasing the CR from 10.5 to 14.5 allowed an absolute increase in indicated thermal efficiency of snore than 3% for 7.5% NG (2.5% gasoline) operation at 8 bar net indicated mean effective pressure (IMEP) and 2500 rpm. However, as anticipated, the achievable peak load at CR 14.5 with 100% gasoline was greatly reduced due to its lower knock resistance. The in cylinder turbulence level was varied by means of tumble plates (TPs) as well as an insert for the NG injector that guides the injection "spray" to augment the tumble motion. The usage of TPs showed a significant increase in EGR dilution tolerance for pure gasoline operation, however, no such impact was found for blended operation of gasoline and NG.

Sevik, James↗

Densification and residual stress induced by CO2 laser-based mitigation of SiO2 surfaces

Knowing the ultimate surface morphology resulting from CO{sub 2} laser mitigation of induced laser damage is important both for determining adequate treatment protocols, and for preventing deleterious intensification upon subsequent illumination of downstream optics. Physical effects such as evaporation, viscous flow and densification can strongly affect the final morphology of the treated site. Evaporation is a strong function of temperature and will play a leading role in determining pit shapes when the evaporation rate is large, both because of material loss and redeposition. Viscous motion of the hot molten material during heating and cooling can redistribute material due to surface tension gradients (Marangoni effect) and vapor recoil pressure effects. Less well known, perhaps, is that silica can densify as a result of structural relaxation, to a degree depending on the local thermal history. The specific volume shrinkage due to structural relaxation can be mistaken for material loss due to evaporation. Unlike evaporation, however, local density change can be reversed by post annealing. All of these effects must be taken into account to adequately describe the final morphology and optical properties of single and multiple-pass mitigation protocols. We have investigated, experimentally and theoretically, the significance of such densification on residual stress and under what circumstances it can compete with evaporation in determining the ultimate post treatment surface shape. In general, understanding final surface configurations requires taking all these factors including local structural relaxation densification, and therefore the thermal history, into account. We find that surface depressions due to densification can dominate surface morphology in the non-evaporative regime when peak temperatures are below 2100K.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of Pressure and Temperature on Carbon Dioxide Reduction at a Plasmonically Active Silver Cathode

Here, carbon dioxide reduction at a plasmonically active silver cathode was investigated by varying the pressure and temperature at multiple applied potentials under both dark and illuminated conditions to understand the mechanism of selectivity changes driven by plasmon-enhanced electrochemical conversion. Carbon dioxide partial pressures (P Co 2 ) from 0.2 to 1 atm were studied during linear sweep voltammetry and chronoamperometry at -0.7, -0.9, and -1.1 V RHE . At a given applied overpotential the total current density increased with increasing P Co 2 in both the dark and the light, but there were significant differences in the Tafel behavior between dark and illuminated conditions. The reduction of CO 2 to carbon monoxide (CO) was found to have first-order behavior with respect to P Co 2 at all applied potentials in both the dark and the light, likely indicating no change in the rate-determining step upon illumination. Activity for the hydrogen (H 2 ) evolution reaction decreased with increasing P Co 2 at slightly different rates in the dark and the light at each applied potential, making it unclear if light is influencing CO or H 2 intermediate adsorbate coverage. Both formate and methanol production showed no dependence on P Co 2 under any conditions, but the true reaction orders may be masked by the much higher activity for CO and H 2 at the silver cathode. The investigation of product distribution with temperature at 14, 22, and 32°C at -0.7, -0.9, and -1.1 V RHE in both the dark and the light demonstrated that the selectivity changes observed upon illumination are not caused by local heating of the cathode surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of pressure and composition on lattice parameters and unit-cell volume of (Fe,Mg)SiO[subscript 3] post-perovskite

We obtained unit-cell volumes (V) for (Fe{sub 0.2}Mg{sub 0.8})SiO{sub 3} and (Fe{sub 0.4}Mg{sub 0.6})SiO{sub 3} post-perovskite (PPv) over a pressure (P) range of 80-145 GPa by in-situ X-ray diffraction (XRD) measurements in laser-heated diamond anvil cells (DACs). Our study suggests that the PPv structure is highly resistant to back transformation to Pv and (Fe{sub 0.4}Mg{sub 0.6})SiO{sub 3} PPv was preserved down to 80 GPa upon laser heating during decompression before transforming to pure perovskite (Pv). The bulk modulus (K{sub 0}) of PPv was determined to be 215(1) and 198(1) GPa for (Fe{sub 0.2}Mg{sub 0.8})SiO{sub 3} and (Fe{sub 0.4}Mg{sub 0.6})SiO{sub 3} PPv respectively, with a fixed K'{sub 0} = 4. The substitution of Fe for Mg in PPv results in the largest expansion along the b-axis among all three axes and the expansion of the b-axis is nearly independent of pressure whereas the expansion along the a and c directions slightly decreases with increasing pressure. Combining our results with previous studies on (Fe{sub x},Mg{sub 1-x})SiO{sub 3} PPv (x = 0, 0.09, 0.1) shows that the bulk modulus of PPv decreases with increasing Fe content over a composition range x = 0 to 0.4, varying from 231 GPa for x = 0 to 198 GPa for x = 0.4 with zero pressure volumes scaled to composition, V{sub 0} ({angstrom}{sup 3}) = 162.2 + 19.5x and fixed K'{sub 0} = 4.0. The increase of Fe content in PPv from x = 0 to 0.4 results in a 6.3% increase in density and a 5.3% decrease in bulk sound velocity at 130 GPa.

58 GEOSCIENCES↗

Quantifying the effects of pressure management for the Williston basin Brine Extraction and Storage Test (BEST) site using machine learning

Active reservoir management (ARM) through brine extraction can reduce pressure buildup during large-scale implementation of carbon capture and storage (CCS) projects. This study used machine learning (ML)-assisted approaches to analyze bottomhole pressure (BHP) responses to various brine injection and extraction scenarios. Field monitoring data were collected over a 2-year operation period at two injection wells and one extraction well (about 400 meters away) as part of a Brine Extraction and Storage Test (BEST) in the North Dakota portion of the Williston Basin. Injection activities increased the BHPs at the injection wells by around 0.70 MPa (~100 psi) during the operation period. Extraction activities demonstrated the capability to decrease the BHPs at the injection wells by approximately 0.21–0.34 MPa (30–50 psi) depending on the ratio of the extraction and injection well flow rates (the “extraction ratio” – a normalization procedure used in the analysis). The pressure reduction provided by the extraction well equated to 30%–50% of the pressure buildup at the injection well. Furthermore, this work shows how ML analytics can play a key role in estimating reservoir pressure responses for complex injection and extraction activities during pressure management practices of CCS projects.

58 GEOSCIENCES↗

Effect of pressure on f-electron delocalization and oxidation in actinide dioxides

Using rstprinciplescalculations,wehaveinvestigatedf-electrondelocalizationandoxidationintheactinidedioxidesunderpressure.WhilstUO2isfoundonthevergeofaninsulatortometaltransitionattheequilibriumvolume,increasinglylargerpressuresarerequiredtodelocalizef-electronsinNpO2,PuO2,andAmO2,respectively49,112,and191GPa.Comparedtothisbroadrangeofpressures,theexper-imentallyobservedstructuraltransitions,inallfourdioxides,occurbetween30and40GPa,whichleadsustoconcludethattheassociatedvolumecollapseisnotduetof-electrondelocalization.Incontrast,oxi-dationofthedioxidesisfoundtobelinkedtothedegreeoff-electronlocalization,butitemergesthatfornaturallyoccurringpressures(<10GPa),higheroxidesonlyexistforUO2.

Petit, Leon↗