SEARCH · Search NASA

Results for “Parametric Design Study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS2011

Numerical Investigation of the Interaction of Counterflowing Jets and Supersonic Capsule Flows

Use of counterflowing jets ejected into supersonic freestreams as a flow control concept to modify the external flowfield has gained renewed interest with regards to potential retropropulsion applications pertinent to entry, descent, and landing investigations. This study describes numerical computations of such a concept for a scaled wind-tunnel capsule model by employing the space-time conservation element solution element viscous flow solver with unstructured meshes. Both steady-state and time-accurate computations are performed for several configurations with different counterflowing jet Mach numbers. Axisymmetric computations exploring the effect of the jet flow rate and jet Mach number on the flow stability, jet interaction with the bow shock and its subsequent impact on the aerodynamic and aerothermal loads on the capsule body are carried out. Similar to previous experimental findings, both long and short penetration modes exist at a windtunnel Mach number of 3.48. It was found that both modes exhibit non-stationary behavior and the former is much more unstable than the latter. It was also found that the unstable long penetration mode only exists in a relatively small range of the jet mass flow rate. Solution-based mesh refinement procedures are used to improve solution accuracy and provide guidelines for a more effective mesh generation procedure for parametric studies. Details of the computed flowfields also serve as a means to broaden the knowledge base for future retropropulsion design studies.

Venkatachari, Balaji Shankar↗

NASA NTRS2014

Power System Overview for the Small RPS Centaur Flyby and the Mars Polar Hard Lander NASA COMPASS Studies

The NASA Glenn Research Center (GRC) Radioisotope Power System Program Office (RPSPO) sponsored two studies lead by their mission analysis team. The studies were performed by NASA GRCs Collaborative Modeling for Parametric Assessment of Space Systems (COMPASS) team. Typically a complete toplevel design reference mission (DRM) is performed assessing conceptual spacecraft design, launch mass, trajectory, science strategy and sub-system design such as, power, propulsion, structure and thermal.

Space Missions↗

NASA NTRSDate not supplied

Model-Based Systems Engineering, Real-Time Operations, and Autonomy

Model-Based Systems Engineering has been enabled by the development of the SysML language and software tools to create systems models. Systems models described in SysML incorporate frames (Diagrams) that represent behaviors (activities, sequences, state machines, use cases), requirements, and structure (definitions, internal structure, parametric formulation, and packaging). The SysML models are, in turn, used by applications to do analysis and studies of the designs and operational capabilities. These uses of the model are based on simulations, and do not include hardware. This paper presents a software environment and processes that enables more comprehensive systems models for MBSE, and use of these rich models for real-time operations. The paper describes a software platform that enables creation of comprehensive models, beyond what is now possible with SysML and related software tools, called the NASA Platform for Autonomous Systems (NPAS). The platform encapsulates a paradigm and infrastructure for creating systems models with complexity levels comparable to the ones handled by SysML software tools, but with additional fidelity that includes detailed design diagrams encompassing sensors, components, and design topologies. Furthermore, NPAS enables incorporation of data, information, and knowledge (DIaK) to implement autonomy and Integrated System Health Management (ISHM) and the inherent integration of content encompassing SysML structure and behavior diagrams throughout the NPAS modelAnd lastly, the NPAS models are used in real-time operations, taking advantage of the fidelity and complexity encompassed in the models in order to implement “thinking” ISHM and/or autonomous operations. . Incorporation of SysML model content into an NPAS model is briefly discussed.

MBSE↗

NASA NTRS1988

Parametric studies of advanced turboprops

The effects of geometric variables (sweep and twist) on the structural performance of advanced turboprops are investigated. The investigation is limited to aerodynamically efficient turboprops using an acceptable design configuration as a baseline. The baseline configuration is modified using a seven by seven array of independently varying sweep and twist parameters while maintaining acceptable aerodynamic efficiency. The turboprop structural performance is evaluated in terms of critical speeds, tip displacements, and vibration frequencies where geometric nonlinearities are included. The results obtained are presented in such a manner as to highlight the effects of sweep and twist on the structural performance of aerodynamically efficient turboprop configurations.

Fertis, D. G.↗

NASA NTRS1988

Parametric studies of advanced turboprops

Maser, J. G.↗

NASA NTRS2017

Norton-Thevenin Receptance Coupling (NTRC) as a Payload Design Tool

The NASA Engineering and Safety Center (NESC) is funding a study to develop an alternate method for performing coupled loads analysis called Norton-Thevenin Receptance Coupling (NTRC). NTRC combines Receptance Coupling (RC), a frequency-domain synthesis method and Norton-Thevenin (NT) theory, an impedance based approach for simulating the interaction between dynamic systems. The goal of developing the NTRC method is to provide a tool that payload developers can use to reduce the conservatism in defining preliminary design loads, assess the impact of design changes between formal load cycles, and to perform trade studies for design optimization with a minimum amount of data required from the launch vehicle (LV) provider. NTRC also has the ability to perform parametric loads analysis where many different design configurations can be evaluated. This will result in cost and schedule benefits to the payload developer that are currently not possible under the standard coupled loads analysis (CLA) flow where typically only 2-3 official load cycles are performed by the LV provider over the life of a payload program. NTRC is not envisioned as a replacement for the official load cycles performed by the LV provider but rather as a means to address the types of design issues faced by the payload developer before and between official load cycles.The presentation provides an overview of the NTRC methodology and discusses how NTRC can be used to replicate the results from a standard LV CLA. The presentation covers the benchmarking that has been performed as part of the NESC study to demonstrate the accuracy of the technique for both frequency and time domain dynamic analyses. Future plans for benchmarking the NTRC approach against CLA results for NASAs Space Launch System (SLS) and commercial launch vehicles are discussed and the role that NTRC is envisioned to play in the payload development cycle.

Structural Dynamics↗

NASA NTRS1965

Shielding requirements for manned orbiting space stations

A detailed parametric investigation of radiation shielding requirements was performed for first generation manned orbiting space stations. Two specific space station designs were studied; the results of the shielding analysis are based on the actual geometry of the vehicles, onboard equipment, and supplies. Results are presented for circular orbits ranging from 100 to 600 nautical miles and from 29° to 90° inclination. The effects of the geometry of the space stations, the use of personal shielding, and the use of particular shielding materials are discussed.

MANNED ORBITAL SPACE STATION /MOSS/↗

NASA NTRS1976

Fatigue life analysis for traction drives with application to a toroidal type geometry

A contact fatigue life analysis for traction drives was developed which was based on a modified Lundberg-Palmgren theory. The analysis was used to predict life for a cone-roller toroidal traction drive. A 90-percent probability of survival was assumed for the calculated life. Parametric results were presented for life and Hertz contact stress as a function of load, drive ratio, and size. A design study was also performed. The results were compared to previously published work for the dual cavity toroidal drive as applied to a typical compact passenger vehicle drive train. For a representative duty cycle condition wherein the engine delivers 29 horsepower at 2000 rpm with the vehicle moving at 48.3 km/hr (30 mph) the drive life was calculated to be 19,200 km (11 900 miles).

Coy, J. J.↗

NASA NTRS1978

Ion beam divergence characteristics of two-grid accelerator systems

The first comprehensive experimental investigation of two-grid accelerator systems is presented. A wide range of geometrical grid parameters and grid set operating conditions were investigated for their effect on ion beam divergence. Ion beam divergence was found to depend most strongly on normalized perveance per hole, grid separation ratio, net-to-total accelerating voltage ratio, and discharge-to-total accelerating voltage ratio variations. The graphical results contained herein provide guidelines for the design of ion accelerator systems. A general ion beam divergence angle correlation was developed to permit approximate beam divergence estimates, at parametric values other than those tested, of present grid set designs. Although argon was the main test gas used in this study, it is shown that the results are applicable to other propellants as well.

Aston, G.↗

NASA NTRS1979

Navigation system design for a Halley Flyby/Tempel 2 Rendezvous mission using ion drive

A dual comet (Hall Flyby/Tempel 2 Rendezvous) mission, making use of the solar electric propulsion system, is under consideration for a 1985 launch. This paper describes the preliminary navigation system design for this mission. Orbit determination and guidance strategies for each mission phase are discussed. Navigation accuracy analyses and parametric senstivity studies for the Tempel 2 rendezvous approach phase are presented.

Wood, L. J.↗

NASA NTRS1986

Predicted effect of dynamic load on pitting fatigue life for low-contact-ratio spur gears

How dynamic load affects the surface pitting fatigue life of external spur gears was predicted by using the NASA computer program TELSGE. Parametric studies were performed over a range of various gear parameters modeling low-contact-ratio involute spur gears. In general, gear life predictions based on dynamic loads differed significantly from those based on static loads, with the predictions being strongly influenced by the maximum dynamic load during contact. Gear mesh operating speed strongly affected predicted dynamic load and life. Meshes operating at a resonant speed or one-half the resonant speed had significantly shorter lives. Dynamic life factors for gear surface pitting fatigue were developed on the basis of the parametric studies. In general, meshes with higher contact ratios had higher dynamic life factors than meshes with lower contact ratios. A design chart was developed for hand calculations of dynamic life factors.

Lewicki, David G.↗

NASA NTRS1991

Tiltrotor ground noise reduction from rotor parametric changes as predicted by ROTONET

A simple acoustic footprint trend study has been performed to determine the sensitivity of a tiltrotor aircraft to simple rotor design variations. Using the XV-15 aircraft as a baseline, the effects of blade number, rotor RPM, and chord on tone and broadband noise were predicted with the ROTONET noise code. Effects on EPNL, PNLT, and OASPL for level forward flight were considered.

Jumper, Stephen J.↗

NASA NTRS1992

Engine system assessment study using Martian propellants

A top-level feasibility study was conducted that identified and characterized promising chemical propulsion system designs which use two or more of the following propellant combinations: LOX/H2, LOX/CH4, and LOX/CO. The engine systems examined emphasized the usage of common subsystem/component hardware where possible. In support of this study, numerous mission scenarios were characterized that used various combinations of Earth, lunar, and Mars propellants to establish engine system requirements to assess the promising engine system design concept examined, and to determine overall exploration leverage of such systems compared to state-of-the-art cryogenic (LOX/H2) propulsion systems. Initially in the study, critical propulsion system technologies were assessed. Candidate expander and gas generator cycle LOX/H2/CO, LOX/H2/CH4, and LOX/CO/CH4 engine system designs were parametrically evaluated. From this evaluation baseline, tripropellant Mars Transfer Vehicle (MTV) LOX cooled and bipropellant Lunar Excursion Vehicle (LEV) and Mars Excursion Vehicle (MEV) engine systems were identified. Representative tankage designs for a MTV were also investigated. Re-evaluation of the missions using the baseline engine design showed that in general the slightly lower performance, smaller, lower weight gas generator cycle-based engines required less overall mission Mars and in situ propellant production (ISPP) infrastructure support compared to the larger, heavier, higher performing expander cycle engine systems.

Pelaccio, Dennis↗

NASA NTRS2019

A Multi-Physics Study on High-Specific Power Li-O2 Batteries for Electric Aircraft

Commercialization of lithium-air batteries faces many challenges, such as electrolyte decomposition, short cycle life, low energy and power density, etc. However, commercialization of Li-O2 batteries for aeronautics is much more challenging due to additional safety constraints on cyclability and performance (high specific power and specific energy). For this presentation, we will discuss inter-related aspects of physics-based modeling of a pack: cell and battery model calibration. In addition, we will evaluate and present optimal battery designs for high discharge current density, high discharge time, and low battery mass using simulation-based optimization.The Finite Element Model (FEM) used to simulate a Li-O2 cell is based on the work of Bevara [1]. The different aspects of the model are based on: porous electrode theory and concentrated electrolyte theory; quantum tunneling model for the resistance of conformal layer of discharge product (Li2O2) [1]; Butler-Volmer kinetics for electrochemical reaction; Fick's diffusion for oxygen transport; and an oxygen dissolution model is applied at the air/electrolyte interface [2]. The electrolyte properties such as ion conductivity, ion diffusion, oxygen diffusion, and mass density of the electrolyte were taken from Molecular Dynamics (MD) simulations [3]; while the other model parameters, which includes mass of cell components, were calibrated to match experiments at high discharge current densities. The cell mass includes the anode, cathode, separator, electrolyte, and other components (such as current collector). This calibrated model is used to perform parametric studies on cathode thickness, porosity, tortuosity, carbon particle size, electrolyte transport and material properties, partial pressure of oxygen, discharge time, and discharge current density to study optimal designs for high specific power and energy. References:1. Bevara, V. & Andrei, P. (2014), J. Electrochem. Soc. 161 (14), A2068-A2079.2.Mehta, M. & Andrei, P. (2015), J. Power Sources. 286, 299-308.3.Liyana-Arachchi, T.; Haskins, J.; Burke, C.; Diederichsen, K.; McCloskey, B.; & Lawson, J. (2018), J. Phys. Chem. B. 122 (36), 8548 - 8559.4.Choi, W.; Kikumoto, H.; Choudhary, R. & Ooka, R. (2018), Applied Energy, 209, 306-321.

Mehta, Mohit↗

NASA NTRSDate not supplied

Recent Langley Aerothermodynamic Laboratory Testing (2019-2022)

In support of flight programs, multiple wind tunnel entries were conducted on reentry vehicle configurations to investigate blunt body aeroheating environments. Blunt body block thermal protection system (TPS) roughness, the Low-Earth Orbit Flight Test of an Inflatable Decelerator aeroshell scalloping, and a woven TPS all were tested to determine the effects of those parameters on increased surface heating to the vehicle. Commercial Crew Program studies also utilized the speed and ease of testing in the LAL to analyze parametric databases of low-earth reentry configurations, like the Boeing CST-100, and vehicles designed to travel to the moon or Mars, such as the SpaceX Starship. LAL wind tunnel investigations also supported several DoD and AFRL flight projects, such as HIFiRE 6 and BOLT. External customers leveraged the LAL testing capability to advance their research programs, including UPSTAR, RocketLab, and Lawrence Livermore National Laboratory. Academia groups benefitted from the inexpensive cost to test in the tunnels for many university collaborations, such as studies conducted in partnership with the University of Maryland on a flat plate, using a pressure rake and investigating fluid structure interactions. Multiple studies in collaboration with Purdue considered boundary layer transition on various cone configurations. Another study was conducted using a cone with shaped roughness elements borrowed from the Arnold Engineering Development Complex. Internal testing included studies using a phosphor thermography system that can measure higher temperatures than the current LAL phosphor capability and a characterization study of the noise in the wind tunnel flow. The breadth of testing across research and commercial paradigms, both internal and external to NASA, different configurations, a variety of test techniques and aerodynamic and aerothermal environments will be discussed in this overview presentation of the recent work conducted in the LAL.

wind tunnel test↗

NASA NTRS1990

Entry vehicle performance analysis and atmospheric guidance algorithm for precision landing on Mars

Future missions to Mars may require pin-point landing precision, possibly on the order of tens of meters. The ability to reach a target while meeting a dynamic pressure constraint to ensure safe parachute deployment is complicated at Mars by low atmospheric density, high atmospheric uncertainty, and the desire to employ only bank angle control. The vehicle aerodynamic performance requirements and guidance necessary for 0.5 to 1.5 lift drag ratio vehicle to maximize the achievable footprint while meeting the constraints are examined. A parametric study of the various factors related to entry vehicle performance in the Mars environment is undertaken to develop general vehicle aerodynamic design requirements. The combination of low lift drag ratio and low atmospheric density at Mars result in a large phugoid motion involving the dynamic pressure which complicates trajectory control. Vehicle ballistic coefficient is demonstrated to be the predominant characteristic affecting final dynamic pressure. Additionally, a speed brake is shown to be ineffective at reducing the final dynamic pressure. An adaptive precision entry atmospheric guidance scheme is presented. The guidance uses a numeric predictor-corrector algorithm to control downrange, an azimuth controller to govern crossrange, and analytic control law to reduce the final dynamic pressure. Guidance performance is tested against a variety of dispersions, and the results from selected tests are presented. Precision entry using bank angle control only is demonstrated to be feasible at Mars.

Dieriam, Todd A.↗

NASA NTRS1990

Concepts and analysis for precision segmented reflector and feed support structures

Several issues surrounding the design of a large (20-meter diameter) Precision Segmented Reflector are investigated. The concerns include development of a reflector support truss geometry that will permit deployment into the required doubly-curved shape without significant member strains. For deployable and erectable reflector support trusses, the reduction of structural redundancy was analyzed to achieve reduced weight and complexity for the designs. The stiffness and accuracy of such reduced member trusses, however, were found to be affected to a degree that is unexpected. The Precision Segmented Reflector designs were developed with performance requirements that represent the Reflector application. A novel deployable sunshade concept was developed, and a detailed parametric study of various feed support structural concepts was performed. The results of the detailed study reveal what may be the most desirable feed support structure geometry for Precision Segmented Reflector/Large Deployable Reflector applications.

Miller, Richard K.↗

NASA NTRS1992

Buckling behavior of long symmetrically laminated plates subjected to combined loadings

A parametric study is presented of the buckling behavior of infinitely long, symmetrically laminated anisotropic plates subjected to combined loadings. The loading conditions considered are axial tension and compression transverse tension and compression, and shear. Results obtained using a special-purpose analysis, well-suited for parametric studies, are presented for clamped and simply supported plates. Moreover, results are presented for some common laminate constructions, and generic buckling design charts are presented for a wide range of parameters. The generic design charts are presented in terms of useful nondimensional parameters, and the dependence of the nondimensional parameters on laminate fiber orientation, stacking sequence, and material properties is discussed. An important finding of the study is that the effects of anisotropy are much more pronounced in shear-loaded plates than in compression-loaded plates. In addition, the effects of anisotropy on plates subjected to combined loadings are generally manifested as a phase shift of self-similar buckling interaction curves. A practical application of this phase shift is that the buckling resistance of long plates can be improved by applying a shear loading with a specific orientation. In all cases considered in the study, the buckling coefficients of infinitely long plates are found to be independent of the bending stiffness ratio (D sub 11/D sub 22)(1/4).

Nemeth, Michael P.↗