Search NASA⌕ Search

SEARCH · Search NASA

Results for “Performance characteristics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Deformation and Fracture Behavior of Additively Manufactured 316L Stainless Steel

Tensile deformation and fracture behavior of an additively manufactured (AM) 316L stainless steel (SS) in the as-built, stress-relieved, and solution-annealed conditions was investigated using in situ tensile testing in a scanning electron microscope with an electron back scattering diffraction (SEM–EBSD) detector. Analyses were performed to discuss the characteristic deformation and fracture process of the fine-grained AM 316L SS with and without relaxation heat treatment. The as-built 316L showed the highest strength, and both post-build heat treatments lowered the strength of the alloy. Regardless of the post-build processing, the AM 316L SS showed overall higher strength but slightly lower ductility when compared to the wrought (WT) 316L SS. Analysis of EBSD data indicated that the characteristic microstructural features from AM, such as the complex and fine grain morphology, dislocation network, pores, and silicon-rich oxides, evolved and exerted various roles during the tensile deformation and fracture processes. Further, it was obvious that the interaction of dislocation slips with oxide particles and cavities (or pores) resulted in an accelerated cracking in AM 316L SS. Overall, however, their influence on mechanical behavior was limited, as the genuinely high ductility of 316L SS could help avoid any premature or brittle fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Stress relaxation cracking susceptibility evaluation in 347H stainless steel welds

Abstract Stress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.

42 ENGINEERING↗
DOE OSTI2023

Low-carbon fuels for spark-ignited engines: A comparative study of compressed natural gas and liquefied petroleum gas on a CFR engine with exhaust gas recirculation

Decades of work on low-carbon fuels have established their potential for substantial emissions reductions; however, their adoption is still limited by infrastructure concerns and engine efficiency deficits. As infrastructures have begun to evolve, research on strategies that maximize engine efficiency through interactions with fuel properties must also now take center place. This paper compares the performance, emissions, and combustion characteristics of two forefront low-carbon fuels: compressed natural gas (CNG) and liquefied petroleum gas (LPG) in a cooperative fuel research (CFR) engine over a range of compression ratios and engine loads. The effects of exhaust gas recirculation (EGR), end-gas auto-ignition, and a novel combustion control tool, the combustion intensity metric (CIM), were also evaluated at different stoichiometric engine operating conditions. In comparison to LPG, CNG operation demonstrated an extended knock-free regime, allowing engine operation at higher engine loads and compression ratios, but LPG operation exhibited enhanced combustion characteristics with higher peak pressures and faster apparent heat release rates (AHRR). LPG operation achieved higher brake thermal efficiencies and lower equivalent CO 2 emissions compared to CNG operation at the tested engine loads and compression ratios. LPG demonstrated significantly higher EGR tolerance limits compared to CNG, with a maximum of 28% EGR rate, compared to 23% for CNG. This improved EGR dilution tolerance was responsible for a 90% reduction in NOx emissions for LPG compared to a maximum of 70% with CNG. EGR dilution also exhibited more effective knock mitigation potential with LPG, suppressing knock intensity values by up to 98% and transitioning the engine operation towards normal combustion from heavy knocking conditions. As a result, the CIM was found to decrease burn durations and improve the quality of combustion by controlling the desired fraction of end-gas auto-ignition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Influence of fuel ash on the recoverability of copper from the spent material of chemical looping combustion

Chemical looping combustion (CLC) is an advanced energy production technology that inherently separates the CO 2 generated. The oxygen needed for fuel conversion is supplied by the oxygen carrier. When using copper-based oxygen carriers, oxygen carrier attrition is a challenge to the process economics, unless the attrited copper that is mixed with fuel ash in the spent material can be recovered by, for instance, acid leaching. However, fuel ash may transform the attrited copper into certain complexes of low leachability (e.g., CuAl 2 O 4 ), hindering the copper recovery. In this study, the copper content in the spent material was first evaluated. The effects of ash composition and copper content on the occurrence mode of copper in spent material were predicted by thermodynamic modeling. Redox cycles of simulated spent materials based on various coal ashes were performed to reveal the characteristics of CuAl 2 O 4 /CuFe 2 O 4 formation. The CuO-Al 2 O 3 reaction was investigated under the temperatures and solid residence times experienced in CLC. The materials were analyzed by X-ray diffraction. The results suggest that the fuel ash with a high Al/Ca ratio may lower the recoverability of copper when the temperature is above 925 °C. The slow formation of CuFe 2 O 4 is not expected to affect the copper recovery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A carbon molecular sieve membrane-based reactive separation process for pre-combustion CO 2 capture

In this study, we discuss a hybrid system combining a membrane reactor (MR) and an adsorptive reactor (AR), with the MR's reject stream serving as the AR's feed. We apply this system for the water gas shift (WGS) reaction for H 2 generation and simultaneous CO 2 capture in the context of the Integrated Gas Combined Cycle (IGCC) process for power generation from coal and biomass. This MR-AR system attains a high conversion exceeding equilibrium, produces a pure H 2 product for power generation, and delivers a high-pressure CO 2 stream ready for sequestration. Specifically, in our study we use carbon molecular sieve membranes (CMSMs) and a commercial sour-shift WGS catalyst. Lab experiments were carried-out to determine the membrane characteristics, and the MR performance under IGCC-relevant conditions, i.e., for temperatures up to 250 °C and pressures up to 25 bar, employing a model coal gasifier syngas. The CMSM and the catalyst have displayed robust and stable performance during a long-term run (~750 h of syngas exposure). We evaluated the MR-AR system in multi-cycle runs and it has demonstrated superior performance to that of a conventional packed-bed reactor, producing a high-purity H 2 product directly useable in a turbine for power generation. We conclude from the study, that the CMSM-based MR-AR system is a good candidate technology for environmentally-benign power generation. We are currently constructing a pilot-scale system for field demonstration of the technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Evaluation of the CAM6 Climate Model Using Cloud Observations at McMurdo Station, Antarctica

A comparative analysis between observational data from McMurdo Station, Antarctica and the Community Atmosphere Model version 6 (CAM6) simulation is performed focusing on cloud characteristics and their thermodynamic conditions. Ka-band Zenith Radar (KAZR) and High Spectral Resolution Lidar (HSRL) retrievals are used as the basis of cloud fraction and cloud phase identifications. Radiosondes released at 12-hour increments provide atmospheric profiles for evaluating the simulated thermodynamic conditions. Our findings show that the CAM6 simulation consistently overestimates (underestimates) cloud fraction above (below) 3 km in four seasons of a year. Normalized by total in-cloud samples, ice and mixed phase occurrence frequencies are underestimated and liquid phase frequency is overestimated by the model at cloud fractions above 0.6, while at cloud fractions below 0.6 ice phase frequency is overestimated and liquid-containing phase frequency is underestimated by the model. The cloud fraction biases are closely associated with concurrent biases in relative humidity (RH), i.e., high (low) RH biases above (below) 2 km. Frequencies of correctly simulating ice and liquid-containing phase increase when the absolute biases of RH decrease. Cloud fraction biases also show a positive correlation with RH biases. Water vapor mixing ratio biases are the primary contributor to RH biases, and hence, likely a key factor controlling the cloud biases. Finally, this diagnosis of the evident shortfalls of representations of cloud characteristics in CAM6 simulation at McMurdo Station brings new insight in improving the governing model physics therein.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Data mining and computational screening of Rashba-Dresselhaus splitting and optoelectronic properties in two-dimensional perovskite materials

Recent developments highlighting the promise of two-dimensional perovskites have vastly increased the compositional search space in the perovskite family. This presents a great opportunity for the realization of highly performant devices and practical challenges associated with the identification of candidate materials. High-fidelity computational screening offers great value in this regard. In this study, we carry out a multiscale computational workflow, generating a dataset of two-dimensional perovskites in the Dion-Jacobson and Ruddlesden-Popper phases. Our dataset comprises ten B-site cations, four halogens, and over 20 organic cations across over 2000 materials. We compute electronic properties, thermoelectric performance, and numerous geometric characteristics. Furthermore, we introduce a framework for the high-throughput computation of Rashba-Dresselhaus splitting. Finally, we use this dataset to train machine learning models for the accurate prediction of band gaps, candidate Rashba-Dresselhaus materials, and partial charges. The work presented herein can aid future investigations of two-dimensional perovskites with targeted applications in mind.

14 SOLAR ENERGY↗
DOE OSTI2020

Heterogeneous data-processing optimization with CLARA’s adaptive workflow orchestrator

The hardware landscape used in HEP and NP is changing from homogeneous multi-core systems towards heterogeneous systems with many different computing units, each with their own characteristics. To achieve maximum performance with data processing, the main challenge is to place the right computing on the right hardware. In this paper, we discuss CLAS12 charge particle tracking workflow orchestration that allows us to utilize both CPU and GPU to improve the performance. The tracking application algorithm was decomposed into micro-services that are deployed on CPU and GPU processing units, where the best features of both are intelligently combined to achieve maximum performance. In this heterogeneous environment, CLARA aims to match the requirements of each micro-service to the strength of a CPU or a GPU architecture. A predefined execution of a micro-service on a CPU or a GPU may not be the most optimal solution due to the streaming data-quantum size and the data-quantum transfer latency between CPU and GPU. So, the CLARA workflow orchestrator is designed to dynamically assign micro-service execution to a CPU or a GPU, based on the online benchmark results analyzed for a period of real-time data-processing.

Gyurjyan, Vardan↗
DOE OSTI2023

Ageing and quenching through the Ageing Diagram – II. Physical characterization of galaxies

The connection between quenching mechanisms, which rapidly turn star-forming systems into quiescent, and the properties of the galaxy population remains difficult to discern. In this work we investigate the physical properties of MaNGA and SAMI galaxies at different stages of their star formation history. Specifically, we compare galaxies with signatures of recent quenching (Quenched) – Hα in absorption and low D n (4000) – with the rest of the low star-forming and active population (Retired and Ageing, respectively). The analysis is performed in terms of characteristics such as the total stellar mass, half-light radius, velocity-to-dispersion ratio, metallicity, and environment. We find that the Ageing population comprises a heterogeneous mixture of galaxies, preferentially late-type systems, with diverse physical properties. Retired galaxies, formerly Ageing or Quenched systems, are dominated by early-type high-mass galaxies found both at low and dense environments. Most importantly, we find that recently quenched galaxies are consistent with a population of compact low-mass satellite systems, with higher metallicities than their Ageing analogues. We argue that this is compatible with being quenched after undergoing a star-burst phase induced by environmental processes (e.g. ram pressure). However, we also detect a non-negligible fraction of field central galaxies likely quenched by internal processes. This study highlights that, in order to constrain the mechanisms driving galaxy evolution, it is crucial to distinguish between old (Retired) and recently quenched galaxies, thus requiring at least two estimates of the specific star formation rate over different time-scales.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Altermagnetic behavior in OsO 2 : Parallels with RuO 2

We investigate and compare the electronic structure of OsO 2 with the extensively studied RuO 2 . Calculations show that OsO 2 exhibits antiferromagnetism and spin splitting driven by crystal symmetry, a characteristic of altermagnetism and similar to RuO 2 . Examination of the Fermi surface, with and without spin-orbit coupling, reveals that OsO 2 has lower Fermi group velocities compared to RuO 2 , suggesting limited charge carrier mobility in OsO 2 . While this characteristic may constrain its performance in high-speed electronic transport applications, it may also enhance stability for spin-based information storage in spintronics. Additionally, comparison of the vibrational properties of these rutile oxide systems demonstrates dynamical stability, typical mass dependent behaviors, and favorable agreement with measured Raman data. The calculated phonon density of states for RuO 2 also agrees with our neutron scattering data. These observations substantiate the implications of the electronic and vibrational behaviors in OsO 2 and RuO 2 , encouraging further investigation of their potential for emerging technological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Predictive Modeling of Local Film-Cooling Flow on a Turbine Rotor Blade

Abstract In the turbine section of a modern gas turbine engine, components exposed to the main gas path flow rely on cooling air to maintain hardware durability targets. Therefore, monitoring turbine cooling flow is essential to the diagnostic and prognostic efficacy of a condition-based operation and maintenance (CBOM) approach. This study supports CBOM goals by leveraging supervised machine learning to estimate relative changes to local film-cooling flowrate using surface temperature measured on the pressure side of a rotating turbine blade operating at engine-relevant aerothermal conditions. Throughout the lifetime of a film-cooled turbine component, characteristics of the film-cooling flow—such as film trajectory and cooling effectiveness—vary as degradation-driven geometry distortions occur, which ultimately affects the relationship between the model input and the model output—film-cooling flowrate predictions. The present study addresses this complication by testing a data-driven model on multiple turbine blades of the same nominal design, but with each blade exhibiting different localized film-cooling flow characteristics. By testing the model in this manner, strategies for mitigating the detrimental effects of film-cooling flow characteristic variations on model performance were investigated, and the corresponding flowrate prediction accuracy was quantified.

Engineering↗
DOE OSTI2024

Effect of Wettability Gradient on the Scale Formation in Falling Film Flow

Mitigation of scale formation and performance degradation remains a vital challenge for falling film evaporators in various industries. In this work, an experimental study of falling film flow on a horizontal tube is conducted to investigate the effects of wettability gradients on thermal, hydraulic, and fouling behavior. It is revealed that certain hydrophobic coating patterns, such as strip, ring, and grid patterns, lead to unwetted heat transfer area, which results in decreased heat transfer compared to fully wetted plain tube. By adjusting the geometry and position of the wettability gradient, the hybrid coating demonstrates improved heat transfer performance. Based on the characteristics of horizontal tube falling film flow, impinging jet, thin film flow, and liquid retention at the tube bottom, a hybrid coating pattern is developed to improve surface wetting and mitigate the scaling coverage. It is revealed that scale deposition is regulated by wettability gradient. Crystals tend to be dense and compact in hydrophilic areas, while they appear scattered or even absent in hydrophobic regions, depending on the dimension of the hydrophobic area. While at the hydrophilic/hydrophobic boundary, a noticeable scale thickness step is observed, which raises the potential for self-cleaning. Furthermore, the balance of minimization of scaling layer coverage and maximization of wetting area requires an optimal design in coating dimensions, for which a systemic study of both flow dynamics and fouling characteristics on the falling film is necessary in the future.

42 ENGINEERING↗
DOE OSTI2023

Microbiome differences in sugarcane and metabolically engineered oilcane accessions and their implications for bioenergy production

Abstract Oilcane is a metabolically engineered sugarcane ( Saccharum spp. hybrid) that hyper-accumulates lipids in its vegetable biomass to provide an advanced feedstock for biodiesel production. The potential impact of hyper-accumulation of lipids in vegetable biomass on microbiomes and the consequences of altered microbiomes on plant growth and lipid accumulation have not been explored so far. Here, we explore differences in the microbiome structure of different oilcane accessions and non-modified sugarcane. 16S SSU rRNA and ITS rRNA amplicon sequencing were performed to compare the characteristics of the microbiome structure from different plant compartments (leaf, stem, root, rhizosphere, and bulk soil) of four greenhouse-grown oilcane accessions and non-modified sugarcane. Significant differences were only observed in the bacterial microbiomes. In leaf and stem microbiomes, more than 90% of the entire microbiome of non-modified sugarcane and oilcane was dominated by similar core taxa. Taxa associated with Proteobacteria led to differences in the non-modified sugarcane and oilcane microbiome structure. While differences were observed between multiple accessions, accession 1566 was notable in that it was consistently observed to differ in its microbial membership than other accessions and had the lowest abundance of taxa associated with plant-growth-promoting bacteria. Accession 1566 is also unique among oilcane accessions in that it has the highest constitutive expression of the WRI 1 transgene. The WRI 1 transcription factor is known to contribute to significant changes in the global gene expression profile, impacting plant fatty acid biosynthesis and photomorphogenesis. This study reveals for the first time that genetically modified oilcanes associate with distinct microbiomes. Our findings suggest potential relationships between core taxa, biomass yield, and TAG in oilcane accessions and support further research on the relationship between plant genotypes and their microbiomes.

09 BIOMASS FUELS↗
DOE OSTI2019

Challenges in Clinical Trial Implementation: Results from a Survey of the National Accreditation Program of Breast Centers (NAPBC)

Background: Although the results of clinical trials often guide best practices, changing clinical practice based on clinical trial results can be challenging. The objective of this study was to examine provider-reported barriers to adopting best clinical practices according to clinical trial data. Methods: A cross-sectional survey was conducted of providers from the National Accreditation Program for Breast Centers about barriers that prevent the incorporation of trial findings. Descriptive analyses and multivariable analyses were performed to determine provider characteristics that were significantly associated with reported barriers. Results: Overall, 383 institutions participated (63.5% response rate), with a total of 1226 physicians responding to the survey (80% response rate). Providers identified national guidelines and meetings as the most compelling way to receive practice-changing information. They reported the following internal barriers to trial implementation: patient preference (45%), strongly held beliefs by partners/colleagues (37%), and insufficient time to discuss new practices (30%). External barriers preventing trial implementation included a lack of agreement from multidisciplinary tumor boards (32%), fear of reimbursement loss (23%), and resistance from clinical staff (20%). Reported barriers differed by provider specialty, with plastic surgeons and radiation oncologists reporting that strongly held beliefs by partners/colleagues and disagreement from multidisciplinary tumor boards were the most significant factors preventing clinical trial implementation. Conclusions: Physician beliefs and patient preferences are the most frequently reported barriers to clinical trial implementation. Tactics to better educate providers about how to explain new clinical trial data to their patients and colleagues are needed.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2024

SQMS science advances impact on Rigetti commercial processors

The collaboration between the Superconducting Quantum Materials and Systems Center (SQMS) and Rigetti Computing produced several advancements in our understanding of the role of materials characteristics in quantum processor performance. This partnership leverages SQMS's extensive characterization infrastructure and cutting-edge research in materials, and Rigetti's expertise in quantum hardware and robust nanofabrication to improve precision and performance of Rigetti's test QPUs. Qubit frequency is determined in large part by the properties of Josephson junctions (JJs) made of amorphous oxide tunnel barriers; the Alternating-Bias Assisted Annealing (ABAA) process allows us to tune JJs to their desired frequency [1]. Work by SQMS researchers in characterizing high-precision JJs post-processed (using ABAA) have yielded crucial information on the nature of the structure and chemical bonding uniformity of the ABAA processed amorphous oxides. Performance has also been improved through a comprehensive series of experiments that tested encapsulation and surface treatment. Encapsulation of the niobium metal layer with tantalum resulted in an T1 improvement of 80%, experimentally confirming the role of Nb surface losses in qubit performance [2]. Pre-treatment of the underlying silicon surface prior to JJ fabrication by replacing a buffered oxide etch (BOE) with hydrofluoric acid (HF) followed by aqueous ammonium fluoride (NH4F) has shown a statistically significant improvement of T1 by 22%, and reduction in the number of strongly-coupled TLS [3]. These examples, as well as many other published and ongoing investigations, demonstrate the mutual benefits that come from Rigetti's involvement in the SQMS collaboration. [1] - Pappas, D.P., et al. (2024). https://doi.org/10.1038/s43246-024-00596-z [2] - Bal, M., et al. (2024). https://doi.org/10.1038/s41534-024-00840-x [3] Kopas, C. J. et al. Preprint at https://doi.org/10.48550/arXiv.2408.02863 (2024).

Lachman, Ella↗
DOE OSTI2025

Advanced Model Development for Large Eddy Simulation of Oxy-Combustion and Supercritical Carbon Dioxide Power Cycles

A joint experimental and numerical study is performed to observe the characteristics of a supercritical carbon dioxide turbulent mixing layer in the presence of strong nonlinearities in the thermodynamic and transport properties. A bespoke experimental setup is designed and employed for this purpose and provides insight into macroscopic mixing behavior. The mixing is experimentally observed using two techniques: shadowgraphy and spontaneous Raman scattering. Qualitative and quantitative intensity fields obtained via these techniques yield instantaneous and mean density data. Spanwise temperature data is also collected using analogue resistance temperature detectors. These measurements are used to quantify the level of mixed material within the field. The experimental data are supplemented by a companion high-fidelity numerical study. The numerical results are obtained through fully resolved, three-dimensional direct numerical simulation. The numerical dataset permits observation of the near-field mixing characteristics, which are difficult to measure experimentally due to the rapid dynamics and sharp thermophysical gradients in this area. Qualitative field visualizations are presented, followed by quantitative mixed material results and observations regarding thermodynamic property trends at select locations within the field. One-dimensional spectra of the turbulent kinetic energy and solenoidal dissipation are provided to observe the spectral characteristics of the flow. Reynolds stress anisotropy is analyzed graphically through anisotropy invariance maps (Lumley triangles). The mixing quantification, spectral data and anisotropy analysis of a flow at these thermodynamic conditions represent the main outcomes of the work.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Seismic Performance of Conventional and Additively Manufactured U-Shaped Flexural Plates

U-shape flexural plates (UFPs) have gained significant attention in seismic structural design due to their ability to provide stable hysteresis behaviour and serve as effective energy-dissipating devices. Concurrently, Additive Manufacturing (AM) has advanced significantly, enabling the production of metallic components with mechanical properties comparable to those of conventionally manufactured cold-rolled materials. This study aims to explore the seismic response of single and double UFP fabricated through Laser Powder Based Fusion (LPBF) and conventional cold rolled 316L stainless steel (SS). The experimental results are evaluated based on force-displacement hysteresis behaviour, energy dissipation capacity, load-carrying capacity, and stiffness degradation. The findings confirm the efficacy of AM-fabricated UFPs for seismic energy dissipation. Additionally, the results suggest the potential for further improvement through the optimization of AM process parameters, such as laser scan speed, hatch spacing, and layer thickness, to enhance hysteretic performance and energy dissipation characteristics.

Risal, Kshitiz [Idaho State University]↗
DOE OSTI2026

Differences in cluster and internal wake effects from mesoscale and large-eddy simulations off the US East Coast

Mesoscale simulations are increasingly used to estimate wake effects within and between large wind farms, despite limited validation for large-scale wake effects. This study evaluates the capabilities and limitations of mesoscale simulations in capturing wake-induced impacts on wind turbine power production through a direct comparison with large-domain large-eddy simulations (LESs) for three planned offshore wind farms under realistic atmospheric conditions and a range of atmospheric stabilities. We assess mesoscale performance in replicating wake characteristics behind single and multiple turbine clusters and quantify the resulting variability in mean turbine power. Results show that mesoscale Weather Research and Forecasting simulations with the Fitch wind farm parameterization capture key features of the velocity deficit downstream of both single and multiple wind farms, with mean root-mean-square errors near 5 % and good agreement with stability-driven wake behavior. However, in these simulations, the mesoscale Fitch parameterization underestimates power losses from internal wake effects, particularly when turbines align with the prevailing wind direction or under stable stratification. In these conditions, individual wakes persist and dominate downstream power deficits. The coarse resolution of the mesoscale simulations limits their ability to resolve individual wind turbine wakes that drive power fluctuations within wind farms. Nonetheless, mesoscale simulations can yield accurate estimates of combined wake losses from internal and cluster effects across some wind direction sectors, where errors in wake representation may cancel each other out. These findings underscore the strengths of mesoscale simulations for capturing broader wake patterns while highlighting their limitations for modeling turbine-level power losses. Future work should explore hybrid modeling approaches to capture both long-range cluster wake propagation and localized internal wake dynamics.

17 WIND ENERGY↗