Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase Transformations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

High-energy synchrotron x-ray study of deformation-induced martensitic transformation in a neutron-irradiated Type 316 stainless steel

An unusual tensile deformation behaviour in the form of a propagating band along the sample gauge was observed in two neutron-irradiated 316 stainless steel samples during room-temperature tests, leading to a combination of high strength and high ductility. These bands were not observed in an unirradiated counterpart. With the help of in situ high-energy synchrotron x-ray diffraction, the phase-specific crystal information was tracked at different deformation levels in each sample. Post-irradiation and post-deformation samples were examined using electron microscopy to characterize various microstructural features. All samples displayed a deformation-induced martensitic phase transformation, which was identified as a second strain-hardening mechanism accompanying the dislocation hardening. The deformation-induced martensitic transformation was rationalized by the effect of applied stress on the effective martensite start temperature. The results showed that the irradiation did not alter the dislocation hardening and the martensitic transformation mechanisms, but the increased yield strength in irradiated materials facilitated the localized phase transformation at the onset of plastic deformation, in contrast to the unirradiated material which required pre-straining. The hardening effect of the martensitic transformation reduced the tendency towards necking and mitigated the loss of ductility in the irradiated material by carrying the deformation in the form of a propagating band. Despite the beneficial effect from the martensitic transformation, this study indicates that this mechanism cannot not be activated at typical operating temperatures of nuclear reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Extended continuous cooling transformation diagram for 410 stainless steel encompassing δ → γ and γ → αʹ transformations determined by dilatometry

In this study, we use dilatometry to construct an extended Continuous Cooling Transformation (CCT) diagram for 410 stainless steel, capturing both δ → γ and γ → αʹ transformations specifically for directed energy deposition (DED) additive manufacturing (AM) applications. To ensure that the findings are representative of AM specific microstructures and compositions, dilatometry coupons were extracted from a wire arc DED wall, thereby preserving the inherent microstructural and compositional variability within the material. The on-heating phase transformations, including A c1 , A c3 , and γ → δ, were found to be essentially location independent, despite the typical heterogeneity associated with AM. Conversely, increasing cooling rates were observed to shift the start and finish temperatures of both δ → γ and γ → αʹ transformations to lower values. The resulting extended CCT diagram offers a more complete depiction of phase transformation behavior in the system, enabling accurate microstructure evolution modeling and residual stress predictions specifically for directed energy deposition additive manufacturing applications.

Additive manufacturing↗
NASA NTRS1992

Evolution of attached and detached slabs and their associated mantle dynamics

Over the two years of the NASA grant, this project has produced a significant amount of research results related to the plate subduction process and the surface crustal deformation at convergent boundaries (i.e., above subduction zones). While some research objectives are completely accomplished, other research tasks remain active and continue to be investigated at present. A steady state analytic thermal model for subducting slabs was used to examine the torques acting on a descending slab. It is found that gravitational torque vanishes when a slab is dipping either vertically or horizontally, unlike previous studies indicating that the magnitude of gravitational torque decreases as dip angle increases. Subsequently, a new time-dependent, analytic thermal model for a subducting slab was developed. The new model enables us to study transient phenomena associated with plate subduction analytically. On the basis of this model, the nature of slab dip angles was evaluated. Slab dip angles are found to be transient features. As they penetrate into the mantle and increase their lengths, the associated gravitational torque also increases resulting in a downward pulling of the slab to the steeper dip angle. This is especially true once a slab penetrates the olivine-spinel phase boundary at about 400 km depth. However, if the phase transformation does not follow the equilibrium condition, the gravitational torque may have a different behavior. This problem was investigated. Except for fast descending slabs, non-equilibrium phase transformation can only slow down the transient increase of slab dip angles discussed earlier. Its effect is not sufficiently strong to reverse the downward pulling for most of the slabs. However, when slabs subducting at 10 cm/yr or faster, a sufficient amount of metastable olivine can exist beneath 400 km. Because of its low density compared with the surrounding spinel, an upward buoyancy is produced resulting in an upward bending of the slab and possibly an upward rotation of the slab such that smaller dip angles are formed. Seismic studies of the Japanese Slab seem to support this interpretation. The development of oroclinal geometries at convergent boundaries was also examined to study plate obduction which is an important ingredient to the initiation of plate subduction. Although the study suggests that surface features are better modeled by block models, the large scale deformation can be adequately studied by viscous models. Such a model is now under development to complete our original objective to study the initiation of plate subduction. Finally, a three-dimensional, finite element, spherical convective model is developed to study dynamic plate subductions. The model development is now complete and it is being tested to ensure its proper operation. The model is able to generate convection results with a viscosity contrast of about 100. Our research continues to push the viscosity contrast to a level that is appropriate for a subducting slab.

Hsui, Albert T.↗
DOE OSTI2022

Synthesis and Photonic Sintering of Proton Conducting Lanthanide Nickelates

Lanthanide nickelate perovskites are known proton conductors at intermediate temperatures (350-600°C). They are attractive targets for proton conducting fuel cells and electrolyzers due to their operational temperature range and their stability in the presence of CO 2 . These materials have the formula LNiO 3 , with the lanthanide L = La, Ce, Pr, Nd, or Sm. Sintering is challenging due to phase transformations that occur at lower temperatures than those required for sintering. In this project, a series of lanthanide nickelate perovskites was synthesized via both a precursor solid solution method and the glycine nitrate process. Powders derived from the precursor solid solution method for LaNiO 3 and NdNiO 3 were sintered at Utility Global Inc. at various temperatures utilizing fast photonic sintering. LaNiO 3 was successfully sintered while maintaining the perovskite phase. NdNiO 3 underwent a phase transformation at all the conditions tested. The stability of the perovskite phase decreases moving right across the lanthanides in the periodic table, while the expected proton conductivity increases. These results will inform further investigations into lanthanide nickelate perovskites toward the goal of producing a free-standing, sintered, proton-conducting membrane.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Processability and Material Behavior of NiTi Shape Memory Alloys Using Wire Laser-Directed Energy Deposition (WL-DED)

Utilizing additive manufacturing (AM) techniques with shape memory alloys (SMAs) like NiTi shows great promise for fabricating highly flexible and functionally superior 3D metallic structures. Compared to methods relying on powder feedstocks, wire-based additive manufacturing processes provide a viable alternative, addressing challenges such as chemical composition instability, material availability, higher feedstock costs, and limitations on part size while simplifying process development. This study presented a novel approach by thoroughly assessing the printability of Ni-rich Ni55.94Ti (Wt. %) SMA using the wire laser-directed energy deposition (WL-DED) technique, addressing the existing knowledge gap regarding the laser wire-feed metal additive manufacturing of NiTi alloys. For the first time, the impact of processing parameters—specifically laser power (400–1000 W) and transverse speed (300–900 mm/min)—on single-track fabrication using NiTi wires in the WL-DED process was examined. An optimal range of process parameters was determined to achieve high-quality prints with minimal defects, such as wire dripping, stubbing, and overfilling. Building upon these findings, we printed five distinct cubes, demonstrating the feasibility of producing nearly porosity-free specimens. Notably, this study investigated the effect of energy density on the printed part density, impurity pick-up, transformation temperature, and hardness of the manufactured NiTi cubes. The results from the cube study demonstrated that varying energy densities (46.66–70 J/mm3) significantly affected the quality of the deposits. Lower to intermediate energy densities achieved high relative densities (>99%) and favorable phase transformation temperatures. In contrast, higher energy densities led to instability in melt pool shape, increased porosity, and discrepancies in phase transformation temperatures. These findings highlighted the critical role of precise parameter control in achieving functional NiTi parts and offer valuable insights for advancing AM techniques in fabricating larger high-quality NiTi components. Additionally, our research highlighted important considerations for civil engineering applications, particularly in the development of seismic dampers for energy dissipation in structures, offering a promising solution for enhancing structural performance and energy management in critical infrastructure.

Dabbaghi, Hediyeh↗
DOE OSTI2024

Additively Manufacturing Nitinol Shape Memory Alloys for Advanced Actuator Designs

The objective of this research was to understand the role of feedstock production in the phase transformation behavior of additively manufactured Ni-Ti alloys for advanced actuator design. Industrial adoption of additively manufactured Ni-Ti alloys depends on the ability to produce repeatable phase transformation behavior, quantified here by the austenite to martensite transformation on heating. Small variations in the alloy composition may have a significant effect on the temperature at which this transformation occurs. This project showed that the powder characteristics play an important role in determining this behavior. Increases in the surface area per unit volume of the powder, either as a function of size distribution or morphology, have the effect of reducing the Ti content in the alloy through the formation of Ti-rich oxides on the powder surface, which has the effect of depressing the transformation temperature. Preferential Ni vaporization during additive manufacturing can partially offset this effect. To achieve repeatable results, it is important to understand the effect of powder oxidation, and to control the powder characteristics.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Fabrication and characterization of Si3N4 ceramics without additives by high pressure hot pressing

High pressure hot-pressing of Si3N4 without additives was performed using various kinds of Si3N4 powder as starting materials, and the relation between densification and alpha-beta phase transformation was studied. The temperature dependences of Vickers microhardness and fracture toughness were also examined. Densification of Si3N4 was divided into three stages, and it was found that densification and phase transformation of Si3N4 under pressure were closely associated. The results of the temperature dependence of Vickers microhardness indicated that the high-temperature hardness was strongly influenced not only by the density and microstructure of sintered body but also by the purity of starting powder. The fracture toughness values of Si3N4 bodies without additives were 3.29-4.39 MN/m to the 3/2 power and independent of temperature up to 1400 C.

Shimada, M.↗
DOE OSTI2022

Development of a Laser Ultrasonics-based Approach for Rapid Screening of High Entropy Alloys

This project utilized a laser ultrasonic technique to systematically study temperature-induced evolution of material properties in a set of interrelated binary alloys and a high entropy alloy (HEA) fabricated using arc-melting and spark plasma sintering processes. This technique involved the use of a nanosecond duration, high-intensity pulsed laser to thermo-elastically generate ultrasonic waves that propagate in the bulk of the metal alloy. Sub-nanometer-scale displacements associated with the propagating bulk ultrasonic waves were detected along the epicenter on the opposite surface of the sample using a 1 GHz bandwidth photorefractive interferometer. Phase transformations and microstructural changes were inferred from the temperature-dependent trends in the bulk acoustic velocities and features in the ultrasonic epicentral waveforms measured in the binary alloys. These inferences were then correlated with electron/optical microscopy observations and predictions using calculations of phase diagrams (CALPHAD). The results showed that the laser-generated ultrasonic pulses were strongly influenced by changes in material microstructure and could accurately track thermally driven phase transformations and detect the presence of microscale heterogeneities (grain boundaries, dendritic structures, etc.) in the set of binary alloy samples. The measurement approach was then applied to a quinary HEA sample for estimating phase transition temperature and determining microstructural heterogeneity. The rapid, non-contact and non-destructive ultrasonic testing approach demonstrated here is amenable to high throughput combinatorial investigations that can be applied to graded composition HEAs produced using advanced manufacturing methods. When paired with atomistic simulations and CALPHAD modeling, this approach can overcome the bottlenecks faced by current material characterization methods in efficiently screening the vast discovery space of HEAs that spans over a hundred million unique quinary alloy compositions.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Determination of the Accomodation Coefficient Using Vapor/Gas Bubble Dynamics in an Acoustic Field

Non-equilibrium liquid/vapor phase transformations can occur in superheated or subcooled liquids in fast processes such as in evaporation in a vacuum, in processing of molten metals, and in vapor explosions. The rate at which such a phase transformation occurs, Xi, can be described by the Hertz-Knudsen-Langmuir formula. More than one century of the history of the accommodation coefficient measurements shows many problems with its determination. This coefficient depends on the temperature, is sensitive to the conditions at the interface, and is influenced by small amounts of impurities. Even recent measurements of the accommodation coefficient for water (Hagen et al, 1989) showed a huge variation in Beta from 1 for 1 micron droplets to 0.006 for 15 micron droplets. Moreover, existing measurement techniques for the accommodation coefficient are complex and expensive. Thus development of a relatively inexpensive and reliable technique for measurement of the accommodation coefficient for a wide range of substances and temperatures is of great practical importance.

Gumerov, Nail A.↗
DOE OSTI2022

Cation reordering instead of phase transitions: Origins and implications of contrasting lithiation mechanisms in 1D ζ- and 2D α-V 2 O 5

Substantial improvements in cycle life, rate performance, accessible voltage, and reversible capacity are required to realize the promise of Li-ion batteries in full measure. Here, we have examined insertion electrodes of the same composition (V 2 O 5 ) prepared according to the same electrode specifications and comprising particles with similar dimensions and geometries that differ only in terms of their atomic connectivity and crystal structure, specifically two-dimensional (2D) layered α-V 2 O 5 that crystallizes in an orthorhombic space group and one-dimensional (1D) tunnel-structured ζ-V 2 O 5 crystallized in a monoclinic space group. By using particles of similar dimensions, we have disentangled the role of specific structural motifs and atomistic diffusion pathways in affecting electrochemical performance by mapping the dynamical evolution of lithiation-induced structural modifications using ex situ scanning transmission X-ray microscopy, operando synchrotron X-ray diffraction measurements, and phase-field modeling. We find the operation of sharply divergent mechanisms to accommodate increasing concentrations of Li-ions: a series of distortive phase transformations that result in puckering and expansion of interlayer spacing in layered α-V 2 O 5 , as compared with cation reordering along interstitial sites in tunnel-structured ζ-V 2 O 5 . By alleviating distortive phase transformations, the ζ-V 2 O 5 cathode shows reduced voltage hysteresis, increased Li-ion diffusivity, alleviation of stress gradients, and improved capacity retention. The findings demonstrate that alternative lithiation mechanisms can be accessed in metastable compounds by dint of their reconfigured atomic connectivity and can unlock substantially improved electrochemical performance not accessible in the thermodynamically stable phase.

25 ENERGY STORAGE↗
DOE OSTI2024

Molecular-Resolution Electron Imaging of Defects and Dynamics at the Ice-Water Interface

Water crystallization into hexagonal ice (type I h ) is one of the most critical processes relevant to the Earth’s environment and human activities. However, despite recent breakthroughs in imaging non-equilibrium condensed ice structures, the ice-water interface has never been imaged at a molecular resolution. This is primarily due to the low stability of the hydrogen bonds in ice under high-resolution microscopy conditions and a lack of methods to prepare compatible samples. Here, this presentation describes the first molecular-resolution imaging of ice crystallized from liquid water and the ice-water interface using high-resolution transmission electron microscopy (HRTEM). By encapsulating deionized (DI) water between two amorphous carbon (a-C) TEM grids and subsequently freezing it with liquid N 2 on a cryo sample stage, we generated two types of ice: non-equilibrium, condensed ice from the atmosphere and encapsulated ice from the DI water (Fig. 1A). Condensed ice usually shows irregular, spherulitic shapes (Fig. 1B). Selected area electron diffraction (SAED) shows that they are a mixture of cubic and hexagonal crystals (Fig. 1C). On the contrary, encapsulated ice forms thin films that contain large-area single-crystalline regions of hexagonal ice oriented along the [0001] zone axis (Fig. 1D). Differential electron energy-loss spectroscopy (EELS) confirmed the high purity of the encapsulated ice free from organic contaminations that are common in other encapsulation methods for HRTEM such as graphene liquid cells. These single-crystalline areas are robust under the electron beam up to ~100 e/Å 2 s. Aberration-corrected HRTEM imaging in these areas achieved a line resolution of ~1.3 Å (Fig. 1E and F). This platform allows us to study near-equilibrium ice structures and dynamics at an unprecedented spatial resolution (Fig. 2). For example, we discovered subdomain-rich regions near the defective crystal edges despite the structure appearing single-crystalline according to diffraction criteria. These subdomains connect via low-angle grain boundaries with flat energy landscapes as a function of tilt angles (according to simulations), showing the high tolerance of ice to defect structures. When we tuned the sample temperature and electron flux rate, we observed radiolysis-controlled bubble generation and dissolution in ice single crystals near a steady state of bubble dynamics. Furthermore, rich beam-induced melting and recrystallization dynamics were observed at the ice-water interface with lattice resolution. These data represent the first observation of the ice-water phase transformation at the sub-nanometer level. In summary, the methods developed in this work enabled molecular-resolution observations of ice and the ice-water interface and shed light on the microstructures and phase transformation pathways. Finer control on the temperature, electron irradiation profile, and imaging detector could eventually lead to real-time observation of ice nucleation in water and address long-standing questions in the nucleation pathways.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

High-Pressure Apparatus for Monitoring Solid–Liquid Phase Transitions

This work presents a new technique for observing the solid–liquid phase transformations in complex diesel fuel blends and diesel surrogates under high-pressure conditions intended to simulate those occurring in vehicle fuel injectors. A high-pressure apparatus based on a visual identification of freezing and thawing has been designed and built to monitor phase behavior and determine the crystallization temperature of complex fuels to predict wax precipitation. The proposed methodology was validated using pure substances—n-hexadecane (C16H34), cyclohexane (C6H12), and a binary cyclohexane/n-hexadecane mixture—all of which have been well-characterized previously. The crystallization temperatures of these compounds were measured from atmospheric pressure to 400 MPa for temperatures varying from 290 to 363 K and compared to those reported in the literature. The standard error of the estimated temperatures, based on a given pressure, between the experimental data obtained in this work was compared to data in the literature from Domanska et al. This methodology is being extended to investigate the properties of more complex fuel mixtures.

High-Pressure, phase change, diesel, solidificatio↗
DOE OSTI2020

Thermal transport in phase-stabilized lithium zirconate phosphates

The thermal properties of yttrium-stabilized lithium zirconate phosphate [LZP: Li 1+x+y Y x Zr 2-x (PO 4 ) 3 with x = 0.15, -0.2 ≤ y ≤ 0.4 and with x = 0.0, y = 0.0] are presented over a wide temperature range from 30 to 973 K, elucidating the interplay between structural phase transformations and thermal properties in a solid state superionic conducting material. At room temperature, the thermal conductivity decreases by more than 75% as the stoichiometry is changed from lithium deficient to excess and increases with increasing temperature, indicative of defect-mediated transport in the spark plasma sintered materials. The phase transformations and their stabilities are examined by x-ray diffraction and differential scanning calorimetry and indicate that the Y3 + substitution of Zr 4+ is effective in stabilizing the ionically conductive rhombohedral phase over the entire temperature range measured, the mechanism of which is found through ab initio theoretical calculations. Finally, these insights into thermal transport of LZP superionic conductors are valuable as they may be generally applicable for predicting material stability and thermal management in the ceramic electrolyte of future all-solid-state-battery devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Electronic Excitation‐Driven β‐Ga 2 O 3 Metastability Transformation and Self‐Organization Mechanism: β→κ/γ/δ Phases

Here, irradiation-driven multiphase self-organization presents emergent opportunities for the customization of nanoscale engineering properties, dynamically tuning strain-field distributions and interfacial electronic structures. Responding to intense electronic excitation-induced energy deposition, the dominant phase transformations, with varying Gibbs free energy $Δ,G^o_f$ are confirmed as β → κ → γ → δ that are located in specific microregions for Gallium (III) oxide (Ga 2 O 3 ), as follows: (i) Surface-localized interstitial accumulation under compressive stress triggers β → δ via semi-coherent interface formation. (ii) Tensile stress within latent tracks drives vacancy-mediated oxygen layer truncation (4/12 periodicity along ⟨0001⟩), stabilizing coherent 4H (ABCB) κ and 3C (ABC) β (ABC) interfaces through strain-compensated octahedral distortion. (iii) Screw dislocation-mediated lattice relaxation induces β → γ via cation disordering (Ga 3+ occupancy at β-interstitial sites), forming metastable spinel γ with mixed occupancy across 16d/8a Wyckoff sites. Irradiation-driven β-Ga 2 O 3 →κ/γ/δ transitions, as mechanistically revealed via inelastic thermal spike (i-TS) calculations and molecular dynamics simulations, induce defect-mediated nonlinear photoresponse, critical for optoelectronic engineering.

Han, Xinqing [Shandong Univ., Jinan (China)]↗
DOE OSTI2020

Operando structural and chemical evolutions of TiS 2 in Na-ion batteries

Titanium disulfide (TiS 2 ) with high electric conductivity, fast rate capability, and good cycling performance is a promising candidate for electrode material in sodium (Na)-ion batteries. Despite the well-studied electrochemical behaviors of TiS 2 in Li-ion batteries, the detailed reaction mechanism of TiS 2 in Na-ion batteries is not yet fully understood due to a more complex multi-phase conversion process. In this work, reactions of TiS 2 in Na-ion batteries are investigated via a multi-modal synchrotron approach: operando X-ray Absorption Spectroscopy (XAS) – including X-ray Absorption Near-Edge Structure (XANES) and Extended X-ray Absorption Fine Structure (EXAFS) – and ex situ X-ray Powder Diffraction (XPD), coupled with computational modeling. Operando XANES spectra indicate that the redox reactions occur in both Ti and S during the electrochemically driven phase transformation. Multivariate Curve Resolution-Alternating Least Squares (MCR-ALS) analysis of XAS suggests that different numbers of components are involved in the lithiation and sodiation of TiS 2 , with the sodiation including at least one intermediate phase in addition to the starting material and the final sodiation product. Ex situ XPD and Rietveld refinement further determined and quantified the unknown phases, showing that three phases, TiS 2 , Na 0.55 TiS 2 , and NaTiS 2 , participate in the sodiation of TiS 2 . Operando EXAFS results show the changes in the Ti–Ti coordination number and interatomic distance. This explains the coulombic efficiency decay due to the incomplete recovery of the coordination number of Ti after cycling. Overall, this work reveals the reaction mechanism occurring in Na–TiS 2 batteries with a greater quantitative understanding of the structural evolution. By combining the multi-modal synchrotron approach and computational work, this study provides a framework for studying a broader range of electrochemically driven phase-transformation systems towards advanced energy storage and conversion applications.

25 ENERGY STORAGE↗
NASA NTRS1988

Phase transition in solid molecular hydrogen at ultrahigh pressures

Solid normal hydrogen was compressed in a diamond-anvil cell to pressures above 200 GPa. Spontaneous Raman spectra demonstrate that the solid undergoes a structural phase transformation beginning at 145 GPa at 77 K, as evidenced by an abrupt discontinuity in the intramolecular vibron frequency as a function of pressure. The magnitude of the vibron-frequency shift and the pressure-temperature conditions of the phase transformation are consistent with its identification as the theoretically predicted pressure-induced orientational ordering of the molecular solid.

Hemley, R. J.↗
NASA NTRS1995

Micromechanics of composites with shape memory alloy fibers in uniform thermal fields

Analytical procedures are developed for a composite system consisting of shape memory alloy fibers within an elastic matrix subject to uniform temperature fluctuations. Micromechanics for the calculation of the equivalent properties of the composite are presented by extending the multi-cell model to incorporate shape memory alloy fibers. A three phase concentric cylinder model is developed for the analysis of local stresses which includes the fiber, the matrix, and the surrounding homogenized composite. The solution addresses the complexities induced by the nonlinear dependence of the in-situ martensite fraction of the fibers to the local stresses and temperature, and the local stresses developed from interactions between the fibers and matrix during the martensitic and reverse phase transformations. Results are presented for a nitinol/epoxy composite. The applications illustrate the response of the composite in isothermal longitudinal loading and unloading, and in temperature induced actuation. The local stresses developed in the composite under various stages of the martensitic and reverse phase transformation are also shown.

Birman, Victor↗
NASA NTRS2005

Potential High-Temperature Shape-Memory-Alloy Actuator Material Identified

Shape-memory alloys are unique "smart materials" that can be used in a wide variety of adaptive or "intelligent" components. Because of a martensitic solid-state phase transformation in these materials, they can display rather unusual mechanical properties including shape-memory behavior. This phenomenon occurs when the material is deformed at low temperatures (below the martensite finish temperature, Mf) and then heated through the martensite-to-austenite phase transformation. As the material is heated to the austenite finish temperature Af, it is able to recover its predeformed shape. If a bias is applied to the material as it tries to recover its original shape, work can be extracted from the shape-memory alloy as it transforms. Therefore, shape-memory alloys are being considered for compact solid-state actuation devices to replace hydraulic, pneumatic, or motor-driven systems.

Noebe, Ronald D.↗