Search NASA⌕ Search

SEARCH · Search NASA

Results for “REACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Analysis of unsteady reacting flows and impact of chemistry description in Large Eddy Simulations of side-dump ramjet combustors

Among all the undesired phenomena observed in ramjet combustors, combustion instabilities are of foremost importance and predicting them using Large Eddy Simulation (LES) is an active research field. While acoustics are naturally captured by compressible LES provided that the proper boundary conditions are applied, combustion/chemistry modelling remains a critical issue and its impact on numerical predictions must still be assessed for complex applications. To do so, two different ramjet LES's are compared here. The first simulation is based on a standard one-step chemistry known to over-estimate the laminar flame speed in fuel rich conditions. The second simulation uses the same scheme but introduces a correction of reaction rates for rich flames to match a detailed mechanism provided by Peters (1993). Even though the two chemical schemes are very similar and very few points burn in rich regimes, distinct limit-cycles are obtained with LES depending on which scheme is used. Results obtained with the standard one-step chemistry exhibit high frequency self-sustained oscillations. Multiple flame fronts are stabilized in the vicinity of the shear layer developing at the exit of the air inlets. When compared to the experiment, the fitted one-step scheme yields better predictions than the standard scheme. With the fitted scheme, the flame is detached from the air inlets and stabilizes in the regions identified in the experiment (Ristori et al. (2005), Heid and Ristori (2003), Heid and Ristori (2005), Ristori et al. (1999)). LES and experiments exhibit all main low-frequency modes including the first longitudinal acoustic mode. The high frequencies excited with the standard scheme are damped with the fitted scheme. The chemical scheme is found, for this ramjet burner, to have a strong impact on the predicted stability: approximate chemical schemes even in a limited range of equivalence ratio can lead to the occurence of non-physical combustion oscillations. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Flame thickness and conditional scalar dissipation rate in a premixed temporal turbulent reacting jet

The flame structure corresponding to lean hydrogen–air premixed flames in intense sheared turbulence in the thin reaction zone regime is quantified from flame thickness and conditional scalar dissipation rate statistics, obtained from recent direct numerical simulation data of premixed temporally-evolving turbulent slot jet flames. It is found that, on average, these sheared turbulent flames are thinner than their corresponding planar laminar flames. Extensive analysis is performed to identify the reason for this counter-intuitive thinning effect. The factors controlling the flame thickness are analyzed through two different routes i.e., the kinematic route, and the transport and chemical kinetics route. The kinematic route is examined by comparing the statistics of the normal strain rate due to fluid motion with the statistics of the normal strain rate due to varying flame displacement speed or self-propagation. It is found that while the fluid normal straining is positive and tends to separate iso-scalar surfaces, the dominating normal strain rate due to self-propagation is negative and tends to bring the iso-scalar surfaces closer resulting in overall thinning of the flame. The transport and chemical kinetics route is examined by studying the non-unity Lewis number effect on the premixed flames. The effects from the kinematic route are found to couple with the transport and chemical kinetics route. In addition, the intermittency of the conditional scalar dissipation rate is also examined. It is found to exhibit a unique non-monotonicity of the exponent of the stretched exponential function, conventionally used to describe probability density function tails of such variables. As a result, the non-monotonicity is attributed to the detailed chemical structure of hydrogen-air flames in which heat release occurs close to the unburnt reactants at near free-stream temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In situ observations of reacting Al/Fe 2 O 3 thermite: Relating dynamic particle size to macroscopic burn time

Time-resolved x-ray imaging is used to capture high-resolution images of the Al/Fe 2 O 3 thermite reaction as it proceeds in an extended burn tube. The observed thermite reaction products are generally large, multi-phase composite particles. Image processing algorithms are developed to extract a continuous record of composite particle size as a function of time and distance from the ignition point. Small particles are observed immediately after ignition, followed by a rapid increase in particle size and a gradual decline toward late times. Correlating the dynamic particle size with visible light emission from the reaction, we propose a two-stage mechanism where the combination of early ignition and delayed expansion causes the material closest to the ignition point to undergo substantial coalescence before it begins moving down the tube. We also identify two mechanisms that may contribute to particle size refinement at late times, both based on the collapse of large gas bubbles that are observed preferentially in particles at earlier times. A new approach to extracting burn times from luminous intensity data is explored, and we find that a more nuanced analysis of burn time and luminous intensity may help to improve reactivity assessments when data from in situ studies is unavailable.

36 MATERIALS SCIENCE↗

Influence of probe sampling on reacting species measurement in diluted combustion

In-flame measurements of temperature and major species are realized with intrusive probes in a laboratory scale furnace working in diluted combustion. The shape and the position of the reaction zone are experimentally identified from the distribution of temperature and carbon monoxide in a particular symmetry plane. For this purpose, two probes were designed: the sampling probe, to measure species content of the gas sample and the suction pyrometer, for the temperature. The first is completely cooled to quench the reaction, but the second is just partly cooled for handling. However, as both probes take gas sample, the species content is available in either case. Consequently the suction pyrometer can be used to measure simultaneously temperature and species, reducing by half the length of the experimental campaign. Comparing species contents on a non-reactive mixture, it has been observed that the spatial averaging is the same with both probes. The perturbation of the flow is assessed thanks to a CFD modeling of the furnace including the probe. Even if it is significant - the differences between the computed values and the measurements are about 3-4 times the measurement error - the position and the value of the maximum is well captured as well as the opening of the jet. However, the species contents measured within a reactive mixture differ significantly. For a stable regime, the levels and the distribution of CO are similar with both probes, but the gradients at the border of the reaction zone are sharper with the suction pyrometer. For another regime, for which the reaction zone is lifted and less stable, the fields of species are completely different following the probe used. A chemical kinetic modeling has shown that the reaction inside the non-cooled part of the suction pyrometer is promoted when it is placed in particular region. The use of the suction pyrometer as sampling probe inside a reaction zone should therefore be avoided even in diluted combustion. The error made on the fields of species cannot be quantified to be taken into account a posteriori, because in certain conditions the results are completely unrealistic. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of reacting gas flowrates and hydration on the carbonation of anion exchange membrane fuel cells in the presence of CO 2

Anion exchange membrane fuel cells (AEMFCs) have been widely touted as a low-cost alternative to existing proton exchange membrane fuel cells. However, one of the limitations of this technology has been the severe performance penalty related to the introduction of CO 2 to the cell – typically in the air cathode feed. Introduction of CO 2 into AEMFCs results in cell carbonation, which imparts thermodynamic, kinetic and Ohmic overpotentials that can add up to hundreds of millivolts. Therefore, it is important to find strategies and operational protocols for AEMFCs that minimize these overpotentials. In this paper, we reserach the impacts of the anode and cathode flowrate, as well as the cell hydration level, on the extent of cell carbonation and cell polarization. Key findings include: (1) decreasing the cathode flowrate generally decreases the total CO 2 -related voltage loss while changing the anode flowrate has a minimal effect; (2) increasing cell hydration helps to mitigate the performance loss in the presence of CO 2 ; and (3) operational combinations are found that significantly reduce the CO 2 penalty compared to the present literature.

25 ENERGY STORAGE↗

Coarse-Grained-Particle Method for Simulation of Liquid–Solids Reacting Flows

A coarse-grained-particle method (CGPM) that tracks fewer particles and their collisions by lumping several real particles into computational parcels is developed. We demonstrate that the accuracy of CGPM can be improved by properly selecting interpolation schemes used to compute flow variables at particle and computational grid locations. The computational speed of CGPM was shown to be similar to that of a widely used and less accurate particle in cell method (PIC). Finally, a chemical reaction mechanism based on rare earth elements (REE) leaching from coal byproducts was implemented with CGPM to study the effects of several flow and design parameters on the leaching process. A counter-current reactor was studied and optimized to maximize the mass fraction of REE in the liquid solution. As a result, the CGPM can now be employed to cheaply and accurately solve industrial-scale problems containing millions of computational parcels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Aqueous TiO 2 Nanoparticles React by Proton-Coupled Electron Transfer

Redox reactions of aqueous colloidal TiO 2 4 nm nanoparticles (NPs) have been examined, including both citratecapped and uncapped NPs (c-TiO 2 and uc-TiO 2 ). Photoreduction gave stable blue colloidal c-TiO 2 R NPs with 10–60 electrons per particle. Equilibration of these reduced NPs with soluble redox reagents such as methylviologen (MV 2+ ) provided measurements of the colloid reduction potential as a function of pH. The potentials of c-TiO 2 from pH 2–9 varied linearly with pH, with a slope of –60 ± 5 mV/pH. Estimates of the potential at pH 12 were consistent with extrapolating that line to high pH. The reduction potentials did not correlate with the zeta potentials (ζ) or the surface charge of the NPs across this pH range. Similar reduction potentials were observed for c- and uc-TiO 2 at low pH even though they have quite different ζ potentials. These results show that the common surface-charging explanation of the pH dependence is not tenable in these systems. Oxidation of reduced c-TiO 2 R with the electron-transfer oxidant potassium triiodide (KI 3 ) occurred with a significant drop in pH, showing that protons were released when the electrons were removed from the NPs. Smaller pH drops were observed for the proton-coupled electron transfer (PCET) reagents O 2 (air) and 4-MeO-TEMPO (4-methoxy-2,2,6,6-tetramethylpiperine-1-oxy radical). The difference in the number of protons released with KI 3 vs O 2 and 4-MeO-TEMPO was roughly one proton per electron removed. Thus, the thermodynamically preferred reactivity of these colloidal TiO 2 NPs is PCET over the pH 2–13 range studied. The measured redox potentials refer to the chemical process TiO 2 + H + + e – → TiO 2 ·e – ,H + ; and therefore they do not correspond with an electronic energy such as a conduction band edge or flat band potential. The 1e – /1H + stoichiometry means that the TiO 2 reduction potentials correspond to a TiO 2 –H bond dissociation free energy (BDFE), determined to be 49 ± 2 kcal mol –1 . The PCET description is consistent with the pH dependence of E(TiO 2 /TiO 2 ·e – ,H + ), the release of protons upon oxidation, the lack of correlation with ζ potentials, the similarity of capped and uncapped NPs, and the small change in the potential and BDFE from the first to the last electron/proton pair (H atom) removed. Furthermore, this behavior is suggested to be the norm for redox-active oxide/water interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗