Search NASA⌕ Search

SEARCH · Search NASA

Results for “SAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Understanding Bifacial PV Modeling: Raytracing and View Factor Models

As part of the PV Magazine Webinar 'View-factor vs. ray tracing - which bifacial modelling techniques should you use?,' the second part lead by NREL will explore the different rear-irradiance calculation software, which fall into two categories: view-factor and ray-tracing models. View factor models assume isotropic scattering of reflected rays, allowing for calculation of irradiance by integration. Due-diligence software such as PVSyst or SAM use the view-factor model. Ray-tracing models simulate multipath reflection and absorption of individual rays entering a scene. Raytracing software such as bifacial_radiance, which is the only available open-source toolkit, offers the possibility of reproducing complex scenes, including shading or finite-system edge effects. This can be useful to evaluate specific system geometries, shading and obstructions, areas of different albedo and electrical mismatch, all topics of interest to the prediction of bifacial performance. Model agreement for view factors and bifacial_radiance software is improving and has been shown to be between 2% (absolute) when compared with measured results.

14 SOLAR ENERGY↗
DOE OSTI2019

Nb3Sn films for SRF cavities: genesis and RF properties

Understanding of Nb3Sn nucleation and growth is essential to the progress with Nb3Sn vapor diffusion coatings of SRF cavities. Samples representing different stages of Nb3Sn formation have been produced and examined to elucidate the effects of nucleation, growth, process conditions, and impurities. Nb3Sn films from few hundreds of nm up to ~15 µm were grown and characterized using AFM, SEM/EDS, XPS, EBSD, SIMS, and SAM. Microscopic examinations of samples suggest the mechanisms behind Nb3Sn thin film nucleation and growth. RF measurements of coated cavities were combined with material characterization of witness samples to adapt the coating process in "Siemens" coating configuration. Understanding obtained from sample studies, applied to cavities, resulted in Nb3Sn cavity with quality factor 2 ×1010 at 15 MV/m accelerating gradient at 4 K, without "Wuppertal" Q-slope. We discuss the genesis of the Nb3Sn thin film in a typical tin vapor diffusion process, and its consequences to the coating of SRF cavities.

Pudasaini, U.↗
DOE OSTI2021

Renewable Thermal Hybridization Framework for Industrial Process Heat Applications

Renewable thermal energy systems (RTES) could be hybridized with different renewable options (e.g., flat plate collectors (FPCs) with parabolic collectors), or combined with existing heat supplies (e.g., fossil fuels), to give options for targeted solar IPH applications, industrial decarbonization and the reduction of fuel consumption. Buildings and industrial thermal energy applications require different temperature ranges, quantities, and rates of thermal energy, and as such require flexible, cost competitive solutions, able to provide heat over various temperature ranges. Hybrid solutions and thermal energy storage (TES) will be important for the dispatch of heat at optimal times needed by the demand side of the buildings and industrial applications. A variety of tools and platforms, such as the System Advisor Model (SAM), can provide hourly thermal yield simulations from single renewable energy (RE) technology options, including FPCs or CSP for solar IPH. We have investigated a variety of approaches to hybrid system modeling for RTES at different temperatures or combinations of technologies and developed an initial framework. The hybridization framework starts by creating a heat stream and raising the temperature of that heat stream by various combinations of RE technologies and other sources such as fossil fuels, new fuels or electric heating in multiple stages, with options for TES and/or waste heat recovery (WHR).

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Evaluation of Low-Pressure-Sintered Multi-Layer Substrates for Medium-Voltage SiC Power Modules: Preprint

Direct-bonded aluminum (DBA) multi-layer substrates have been fabricated using low-pressure silver sintering. These multi-layer substrates can be used to reduce the peak electric field strength inside power modules. This benefit is particularly important for medium-voltage silicon carbide (SiC) MOSFETs due to their higher operating voltages. The voiding content and defect density of the bond used to create the multi-layer substrate stackup is critical to the thermal performance and reliability of the power module. This work two low-pressure-assisted sintering techniques; one using nano-silver preform and the other using nano-silver paste to bond 23 mm by 49 mm DBA substrates. Scanning acoustic microscopy (C-SAM) is used to evaluate the bond quality after sintering. To evaluate the reliability of the sintered multi-layer substrates, passive thermal cycling from –40 °C to 200 °C was performed. Cross-sections were cut at pre-determined intervals and imaged with Scanning Electron Microscopy (SEM). After 1,000 thermal cycles, minor cracking was observed, but no failures have occurred.

28 EE - Advanced Manufacturing Office (EE-5A)↗
DOE OSTI2021

Marine Energy Performance Models

This webinar was presented on August 18, 2021 and provides an overview of SAM's marine wave and tidal energy models.

ENERGY PLANNING, POLICY, AND ECONOMY,TIDAL AND WAV↗
DOE OSTI2021

Host cells and methods for producing toluene biochemically

The present invention provides for a genetically modified host cell comprising a first polypeptide comprising a sequence having at least 70% amino acid sequence identity with a phenylacetate decarboxylase, and having an enzymatic activity to decarboxylate a phenylacetic acid into a toluene and a carbon dioxide, and a second polypeptide comprising a sequence having at least 70% amino acid sequence identity with a phenylacetate decarboxylase activating enzyme, and having an enzymatic activity to cleave a S-adenosylmethionine (SAM) to form a methionine and a 5′-deoxyadenosyl radical.

Beller, Harry R.↗
DOE OSTI2022

Concentrated Solar Power as a Pathway for Electrolytic Hydrogen Production

William Xi and Mark Ruth of the National Renewable Energy Laboratory (NREL), will present a new solar-electrolysis technoeconomic assessment capability: low-temperature and high-temperature electrolysis in the System Advisor Model (SAM) environment. They will also present analysis results including opportunities for solar-hydrogen systems to achieve the $2/kg hydrogen cost target.

concentrating solar power↗
DOE OSTI2022

Value Proposition of UV-Absorbers in PV Module Encapsulation

Various common crystalline silicon cell technologies were exposed to UVA radiation (1.24 Wm-2 nm-1 at 340 nm peak) on the front and back faces at 45 degrees Celsius for periods up to 3000 h, representing about 3 y of solar exposure in Phoenix, Arizona, USA. The resulting degradation of the open-circuit voltage and short-circuit current is presented. Of the various cell types examined, significant levels of degradation were seen in all cases. Less degradation was generally found after UV irradiation of cell fronts and older cell types, whereas a bifacial PERC type exposed on the rear showed about 25% degradation in short circuit current, attributable to lack of a diffused surface field. Selected cells were exposed to UV irradiation with the addition of long pass UV filters to replicate UV-absorbers in encapsulants. Modern cell designs are sensitive to UV-ID because of reduced or eliminated front and back surface field and increased dependence on high quality surface passivation. Single transformation of the independent variable (t, kW h/m^2) could be used to achieve a linear model of the data to extrapolate to 50 y. Solar Advisor Model (SAM) shows appropriate filtering of UV-irradiation can improve LCOE and net present value of plant. Some advanced cell types are seen to be UV-resistant (cell level solutions also exist). Solutions therefore exist on the cell, glass, and encapsulant level. Changes over time in each of these would also need to be considered (solarization, encapsulant browning...).

ENGINEERING,SOLAR ENERGY↗
DOE OSTI2023

Uncertainty Quantification of PV Annual Energy Estimates in the System Advisor Model

This work will detail a proposed uncertainty quantification method for PV annual energy estimates. Motivations behind the proposed methodology will be discussed, including the frequent underperformance of installed PV systems to calculated probability of exceedance values being seen in industry. A methodology in which uncertainty factors correlated to different parts of the PV annual energy model chain are applied to annual energy estimates in conjunction with uncertainty from inter-annual solar resource variability will be described. The application of this methodology in the System Advisor Model (SAM) will also be discussed with example cases and graphical outputs of the probability of exceedance data calculated for the PV annual energy estimates.

energy modeling↗
DOE OSTI2023

Variability in Diurnal and Seasonal Ambient Conditions on Geothermal Plant Performance and Cost: Preprint

Geothermal plant performance is bounded by the second law efficiency, which accounts for the quantity of exergy that can be converted into useful work. This in turn is dependent on the geothermal resource temperature and the temperature of the heat sink (i.e., the ambient temperature). In this study we show that ambient temperature variability on a diurnal and seasonal basis can affect performance and cost estimations for geothermal plants. We have utilized the updated System Advisor Model (SAM) to assess nine geothermal sites with existing resource capacities across three climate zones. Our analysis shows that both evaporatively-cooled flash and air-cooled binary cycle plants are affected by temperature, with a slightly higher effect in EGS binary sites. By assuming an ambient (wet bulb) temperature baseline of 15.6 degrees C (60 degrees F) and comparing baseline results to those from site-specific data we observe up to 15% underestimation of plant performance and up to 20% overestimation of cost.

ambient temperature↗
DOE OSTI2023

Variability in Diurnal and Seasonal Ambient Conditions on Geothermal Plant Performance and Cost

Geothermal plant performance is bounded by the second law efficiency, which accounts for the quantity of exergy that can be converted into useful work. This, in turn, is dependent on the geothermal resource temperature and the temperature of the heat sink (i.e., the ambient temperature). In this study, we show that ambient temperature variability on a diurnal and seasonal basis can affect performance and cost estimations for geothermal plants. We have utilized the updated System Advisor Model (SAM) to assess nine geothermal sites with existing resource capacities across three climate zones. Our analysis shows that both evaporatively-cooled flash and air-cooled binary cycle plants are affected by temperature, with a slightly higher effect in enhanced geothermal system binary sites. By assuming an ambient (wet bulb) temperature baseline of 15.6 degrees C (60 degrees F) and comparing baseline results to those from site-specific data, we observe up to 15% underestimation of plant performance and up to 20% overestimation of cost. These results make a case for the inclusion of location-based weather data as inputs to supply curves that are used in capacity expansion models for the prediction of future geothermal deployment scenarios.

ambient temperature↗
DOE OSTI2022

Coupled Multiphysics Primary Loop Simulations of the Mk1-FHR in the Virtual Test Bed

To support advanced reactor demonstrations, the Virtual Test Bed (VTB) [1] repository hosts a wide range of challenge problems for showcasing modeling and simulation capabil- ities in support of advanced reactor demonstrations. This document presents a coupled multiphysics model of the Mark 1 pebble-bed fluoride-salt-cooled high-temperature reactor (PB-FHR). The analysis leverages NEAMS tools (Griffin [2], SAM [3], Pronghorn [4], and the MOOSE [5] heat con- duction module) for core neutronics, thermal hydraulics of the core and primary loop, and multiscale fuel performance simulations. The analysis was entirely created by coupling standalone simulations of the reactor that were previously available on the VTB. All input files and documentation de- veloped for this example are available on the VTB website: mooseframework.inl.gov/ virtual_test_bed/ . This model was featured in the National Reactor Innovation Cen- ter Tech Talk presented in December 2021.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

COUPLED MULTIPHYSICS PRIMARY LOOP SIMULATIONS OF THE Mk1-FHR IN THE VIRTUAL TEST BED

The Virtual Test Bed (VTB) repository hosts a wide range of challenge problems to showcase modeling and simulation capabilities to support advanced reactor demonstration. A coupled multiphysics model of the Mk1 pebble-bed fluoride-salt-cooled high-temperature reactor (PB-FHR) is presented here. The analysis leverages NEAMS tools (Griffin), SAM, Pronghorn, and the MOOSE heat conduction module) for core neutronics, thermal hydraulics of the core and the primary loop, and multiscale fuel performance simulations. The analysis was entirely created by coupling standalone simulations of the reactor previously available on the VTB. All input files and documentation developed for this example are available on the VTB website: \url{mooseframework.inl.gov/virtual_test_bed/}}. This model was featured in the NRIC Tech Talk presented in December 2021.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Subhourly Clipping Correction Model Comparison

This work will compare the Allen method and Walker method of accounting for subhourly inverter clipping power losses in hourly PV performance models. The Allen method uses a matrix lookup based on DNI clearness and clipping potential to assign a clipping correction loss at each simulation timestep. The Walker method models the PV DC power input to the inverter as a distribution over the hourly timestep and uses integration over the timestep to determine the amount of clipping that occurs within the timestep. Both these models have been recently implemented in the System Advisor Model's (SAM) open-source code, and will be applied to hourly SURFRAD datasets to analyze the subhourly clipping loss predicted by each model for different system designs and inverter loading conditions. Both models will be compared to "true" 1-minute SURFRAD data simulations to see their accuracy against more accurate 1-minute clipping correction loss predictions. This model comparisons will be investigated in more detail at the PVSC conference in Seattle, Washington June 2024.

ENERGY PLANNING, POLICY, AND ECONOMY,MATHEMATICS A↗
DOE OSTI2024

Development of Segregated Thermal-Hydraulics Solvers in MOOSE

The simulation of fluid flows is an essential part of the design and analysis of nuclear systems. Algorithms able to simulate flows at different fidelity levels are available in the Multiphysics Object-Oriented Simulation Environment (MOOSE) and MOOSE-based applications such as Pronghorn \cite{novak2018pronghorn}, Pronghorn-Subchannel, RELAP-7, and SAM. Currently, significant effort is being invested in the development of coarse-mesh Computational Fluid Dynamics (CFD) capabilities within MOOSE and Pronghorn for the simulation of Generation IV nuclear reactors. Traditionally, the solution algorithms in MOOSE have relied on Newton or quasi-Newton methods (such as the preconditioned Jacobian-free Newton-Krylov method) where residuals and Jacobians (or approximations thereof) are constructed. Both Newton and quasi-Newton methods require the solution of a linear system at each nonlinear Newton iteration with the Jacobian as the system matrix. The Jacobian contains blocks originating from all variables in the problem (i.e., for thermal-hydraulics at least pressure, velocities, and temperature). Due to the formulation of the problem in a general multiphysics setting on unstructured mesh, creating a good preconditioner for the linear system can be challenging, thus many fluid applications have utilized direct solver-based methods such as LU factorization. However, with increasing system size and complexity in multi-dimensional problems, the direct solution of linear systems becomes computationally expensive both in execution time and and memory. For this reason, recent effort has focused on adapting segregated solution algorithms for CFD problems in MOOSE. These algorithms use fixed-point iteration between segregated systems whose assembly and preconditioning are easier those of the monolithic system. Initial results show that the segregated solution algorithm outperforms the monolithic approach in terms of memory usage and for large 3D problems in terms of CPU time as well.

42 ENGINEERING↗
DOE OSTI2024

Side-by-Side Comparison of Subhourly Clipping Models: Preprint

Over the past several years there have been numerous attempts at quantifying the inherent power clipping of inverters due to inter-hourly irradiance variability that is not captured in hourly PV performance models. Different models have been proposed to correct for these clipping losses in PV performance estimates, including matrix lookup models, distribution modeling of the PV power performance within a given hour, and machine learning methods. To date, there have been few comprehensive quantitative comparisons of these inverter clipping correction modeling approaches to evaluate the effectiveness of said approaches in predicting the actual behavior of PV system inverter clipping. In this study, we perform such a comparison, evaluating two different clipping correction loss modeling approaches recently implemented in the System Advisor Model (SAM) against clipping losses modeled with 1-minute climate data. These comparisons will be performed across a variety of climate locations and inverter loading ratios to thoroughly analyze the effectiveness of these modeling approaches relative to each other. Results from this analysis reveal that both clipping correction approaches improve annual energy accuracy to within 2% of 1-minute modeled energy yield. The models can improve accuracy up to 3% in systems with ILR of 2.0, showing the importance of this modeling factor in energy yield estimates.

clipping↗
DOE OSTI2024

Bias Correction and Statistical Downscaling of Solar Radiation Using NA-CORDEX and the NSRDB

The current state-of-art for estimating long-term PV production uses long-term estimates of solar radiation variables, such as global horizontal irradiance (GHI), from previous years. This data is used in models such as the System Advisor Model (SAM) or PYSyst to predict annual production for a PV plant. This information is then used to estimate the production over the next 20 years (a typical plant lifetime) under the assumption that the variability over the current period is representative of the future. As the PV industry moves to extend plant lifetimes to 50 years the current assumptions of representativeness of weather may not be appropriate. This is especially true as our climate changes rapidly. To assess long-term PV production, future projections for solar radiation based on projected carbon emissions are readily available in regional and global climate models. However, climate model projections contain inherent biases that may need to be corrected for accurate analysis of future projections of climate variables. Several studies have analyzed projections of solar radiation for future years, however the accuracy of the model output compared to current and historic data has not been widely studied. Chen (2021) showed that available climate models do not accurately represent solar radiation in some cases, over-projecting GHI at the surface while under-projecting its obstructions, such as clouds and aerosols. This works aims to (1) increase understanding of the accuracy of solar radiation currently available in global and regional climate models and (2) implement bias correction through linear models based on reanalysis data compared to observed solar radiation. The latter aim will be conducted using available observed solar radiation data and modeled data from several regional climate models (RCMs). The bias correction method will be applied to projections of solar radiation resulting in a more accurate representation of the future of solar production.

climate data↗