Search NASA⌕ Search

SEARCH · Search NASA

Results for “SELF OPERATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

NASA Langley's Formal Methods Research in Support of the Next Generation Air Transportation System

This talk will provide a brief introduction to the formal methods developed at NASA Langley and the National Institute for Aerospace (NIA) for air traffic management applications. NASA Langley's formal methods research supports the Interagency Joint Planning and Development Office (JPDO) effort to define and develop the 2025 Next Generation Air Transportation System (NGATS). The JPDO was created by the passage of the Vision 100 Century of Aviation Reauthorization Act in Dec 2003. The NGATS vision calls for a major transformation of the nation s air transportation system that will enable growth to 3 times the traffic of the current system. The transformation will require an unprecedented level of safety-critical automation used in complex procedural operations based on 4-dimensional (4D) trajectories that enable dynamic reconfiguration of airspace scalable to geographic and temporal demand. The goal of our formal methods research is to provide verification methods that can be used to insure the safety of the NGATS system. Our work has focused on the safety assessment of concepts of operation and fundamental algorithms for conflict detection and resolution (CD&R) and self- spacing in the terminal area. Formal analysis of a concept of operations is a novel area of application of formal methods. Here one must establish that a system concept involving aircraft, pilots, and ground resources is safe. The formal analysis of algorithms is a more traditional endeavor. However, the formal analysis of ATM algorithms involves reasoning about the interaction of algorithmic logic and aircraft trajectories defined over an airspace. These trajectories are described using 2D and 3D vectors and are often constrained by trigonometric relations. Thus, in many cases it has been necessary to unload the full power of an advanced theorem prover. The verification challenge is to establish that the safety-critical algorithms produce valid solutions that are guaranteed to maintain separation under all possible scenarios. Current research has assumed perfect knowledge of the location of other aircraft in the vicinity so absolute guarantees are possible, but increasingly we are relaxing the assumptions to allow incomplete, inaccurate, and/or faulty information from communication sources.

Butler, Ricky W.↗

4D Dynamic RNP Annual Interim Report-Year 1

This Annual Interim Report summarizes the activities led by Raytheon, in collaboration with GE Aviation and SAIC, and presents the results obtained during the first year of this research effort to expand the RNP concept to 4 dimensions relative to a dynamic frame of reference. Joint Program Development Office (JPDO)Concepts of Operations for the Next Generation Air Transportation System (NextGen) considers 4 Dimension Trajectory (4DT) procedures a key enabler to Trajectory Based Operations (TBO). The JPDO defines 4DT as a precise description of an aircraft path in space and time . While NextGen assumes that this path is defined within an Earth-reference frame, many 4DT procedure implementations will require an aircraft to precisely navigate relative to a moving reference such as another aircraft to form aggregate flows or a weather cell to allow for flows to shift. Current methods of implementing routes and flight paths rely on aircraft meeting a Required Navigation Performance (RNP) specification and being equipped with a monitoring and alerting capability to annunciate when the aircraft system is unable to meet the performance specification required for the operation. Since all aircraft today operate within the NAS relative to fixed reference points, the current RNP definition is deemed satisfactory. However, it is not well understood how the current RNP construct will support NextGen 4DT procedures where aircraft operate relative to each other or to other dynamic frames of reference. The objective of this research effort is to analyze candidate 4DT procedures from both an Air Navigation Service Provider (ANSP) and aircraft perspective, to identify their specific navigational requirements, assess the shortcomings of the current RNP construct to meet these requirements, to propose an extended 4 Dimensional Dynamic RNP (4D Dynamic RNP) construct that accounts for the dynamic spatial and temporal nature of the selected 4DT procedures, and finally, to design an experiment using the Airspace and Traffic Operations Simulation (ATOS) system to validate the 4D Dynamic RNP construct. This Annual Interim Report summarizes the activities led by Raytheon, in collaboration with GE Aviation and SAIC, and presents the results obtained during the first year of this research effort to expand the RNP concept to 4 dimensions relative to a dynamic frame of reference. A comprehensive assessment of the state-of-the-art international implementation of current RNP was completed and presented in the Contractor Report RNP State-of-the-Art Assessment, Version 4, 17 December 2008 . The team defined in detail two 4DT operations, Airborne Precision Spacing and Self-Separation, that are ideally suited to be supported by 4D Dynamic RNP and developed their respective conceptual frameworks, Required Interval Management Performance (RIMP) Version 1.1, 13 April 2009 and Required Self Separation Performance (RSSP) Version 1.1, 13 April 2009 . Finally, the team started the development of a mathematical model and simulation tool for RIMP and RSSP scheduled to be delivered during the second year of this research effort.

Finkelsztein, Daniel M.↗

Verification of a New NOAA/NSIDC Passive Microwave Sea-Ice Concentration Climate Record

A new satellite-based passive microwave sea-ice concentration product developed for the National Oceanic and Atmospheric Administration (NOAA)Climate Data Record (CDR) programme is evaluated via comparison with other passive microwave-derived estimates. The new product leverages two well-established concentration algorithms, known as the NASA Team and Bootstrap, both developed at and produced by the National Aeronautics and Space Administration (NASA) Goddard Space Flight Center (GSFC). The sea ice estimates compare well with similar GSFC products while also fulfilling all NOAA CDR initial operation capability (IOC) requirements, including (1) self describing file format, (2) ISO 19115-2 compliant collection-level metadata,(3) Climate and Forecast (CF) compliant file-level metadata, (4) grid-cell level metadata (data quality fields), (5) fully automated and reproducible processing and (6) open online access to full documentation with version control, including source code and an algorithm theoretical basic document. The primary limitations of the GSFC products are lack of metadata and use of untracked manual corrections to the output fields. Smaller differences occur from minor variations in processing methods by the National Snow and Ice Data Center (for the CDR fields) and NASA (for the GSFC fields). The CDR concentrations do have some differences from the constituent GSFC concentrations, but trends and variability are not substantially different.

Passive Microwave↗

Using Systems Engineering to Develop an Integrated Crew Health and Performance System to Mitigate Risk for Human Exploration Missions

New space exploration missions are currently being designed to take humanity beyond Low EarthOrbit (LEO) to cis-lunar space, the lunar surface, and eventually to Mars. These missions carryincreased risks due to a number of factors, including distance from Earth, exposure to deep spacehazards, reduced capacity and ability to resupply and evacuate, and increased communication delays.As distance from Earth grows and mission length increases, a growing proportion of overall missionrisk can be attributed to the “human system.” Almost twenty years ago, the Institute of Medicine in theUnited States recommended the early and complete integration of the human system into thespacecraft and mission design process to mitigate this increased risk inherent in exploration missions.Exploration missions will require increasing levels of crew self-sufficiency that will challenge thecurrent operational paradigms established in LEO. Enabling progressive Earth independence requiresmanagement of the increasingly complex interactions among spacecraft systems and integration of allthe data and functions that affect human health and performance into one coordinated system – theCrew Health and Performance (CHP) system. This system is a critical spacecraft system that isanalogous to other systems such as propulsion, guidance and navigation, or avionics. Design andintegration of the CHP system requires the evidence-based merger of typically disparate disciplinessuch as medicine, human factors, and physiological support system design, using systems engineering(SE) practices. The approach described here enables spacecraft and mission designers to align thescope of a CHP system with mission specific requirements, decrease risk to the crew, and increase theprobability of mission success.

Kerry Mcguire↗

Photonic-crystal-fiber-delivered laser-triggered high-voltage gas switch

A photonic-crystal-fiber-delivered laser-triggered high-voltage gas switch can deliver a peak irradiance of greater than 5.1×1011 W/cm2 to the AK gap for a laser having a wavelength of 1064 nm. The switch is capable of operating at pressures up to 2200 psi; voltages across the gap of greater than 200 kV; operation at less than 70% self-break voltage; shot-to-shot jitter of less than 3 ns; AK gap distances of 3 mm or smaller; and triggering via a fiber-delivered laser pulse energy of as low as 500 μJ.

42 ENGINEERING↗

Electrochemically modulated molten salt reactor

An electrochemically modulated molten salt reactor (EMMSR) that contains a vessel and a power source. The vessel houses a fuel salt, at least a portion of a neutron moderator, and at least a portion of an insulator. The fuel salt includes enough dissolved fissile isotopes to cause continued self-sustaining fission reactions during the operation of the EMMSR. The neutron moderator is configured to slow down fast neutrons produced by the dissolved fissile isotopes. The insulator is configured to electrically isolate the neutron moderator from the vessel. The power source has a positive potential and a negative potential. The positive potential is received by the neutron moderator and the negative potential is received by the vessel.

Jiang, Junhua↗

Self-acting seals for helicopter engines

An experimental evaluation was conducted with NASA-designed self-acting face and circumferential seals for use in the main shaft positions of advanced gas turbine engines. The seals featured Rayleigh step pads (self-acting geometry) for lift augmentation. The tested seals incorporated design improvements over previous self-acting configurations. Self-acting face seals were tested to speeds of 214 m/s (700 ft/sec, 63700 rpm), air pressures of 216.8 N/sq cm abs (314.7 psia), and air temperatures of 688K (778 F). Self-acting circumferential seals were tested to speeds of 183 m/s (600 ft/sec, 47700 rpm), air pressures of 61.8 N/sq cm abs (89.7 psia), and air temperatures of 711 K (820 F). Self-acting face-seals are capable of operating at conditions exceeding conventional seal capability. The limit on speed capability was found to be the flatness of the seal-seat. The self-acting circumferential seal design tested requires further development for use in advanced engines.

Lynwander, P.↗

Meta-Study of Particulate Detection Losses on Radioactive Air Sample Filters

Several mathematical relationships between air sample filter mass loading and the correlated analytical self-absorption factor were developed using data from other published research in this meta-study. Gross-alpha and -beta applications are addressed for this research. As filter media becomes loaded with particulate matter, there is potential for measurement losses due to self-absorption by mass loading. Components contributing to absorption include particulate dust, radioactive particulates, and filter material. Standards indicate a correction factor should be used when the penetration of radioactive material into the collection media or self-absorption of radiation by the material collected would reduce the detection rate by more than 5%. Previously, losses due to self-absorption have been reported up to 100% over a range up to ~10 mg∙cm -2 mass loading. These absorption losses then can be used to determine a correction factor for sample results. For low mass loadings (e.g., ≤0.1 mg∙cm -2 ) corrections factors in the 0.85 - 1 range have been recommended and used, while at higher mass loadings nearer to 10 mg∙cm -2 correction factors closer to 0 (representing near 100% losses) are used. Based on data from published studies, the different methods for relating percent loss due to self-absorption to mass loading include linear, exponential, quadratic, and trinomial derived functions. Where applicable, both forced zero and non-forced zero results were evaluated. From the derived functions evaluated, the trinomial function provided the best fit. Once the sample filter mass loading is known, the trinomial function can be applied to estimate losses and the corresponding self-absorption factor. When applied to routine operating conditions for radiological facility stacks monitored at the Pacific Northwest National Laboratory for an average sample filter mass loading of 0.09 ± 0.12 (2σ) mg∙cm -2 (excluding negative values and outliers) and a range from 0 - 0.24 mg∙cm -2 , the estimated trinomial function nominal self-absorption losses are less than 5% at 0.09 mg∙cm -2 and less than 10% at 0.24 mg∙cm -2 . The trinomial function is one method that may be used to adjust the activity results of an air sample when the sample-specific mass loading is determined. The application of no correction factor when the ANSI/HPS N13.1-2021 guidance of a 5% threshold for loss is not reached with typical stack sample mass loadings may be reasonable in high-efficiency particulate air filtered systems. For simplicity, it would be conservative in assigning the self-absorption correction factor at the 5% threshold (i.e., 0.95) for general uses but in cases of heavy mass loading to calculate the factor.

air sampling↗

Monte Carlo Analysis of Airport Throughput and Traffic Delays Using Self Separation Procedures

This paper presents the results of three simulation studies of throughput and delay times of arrival and departure operations performed at non-towered, non-radar airports using self-separation procedures. The studies were conducted as part of the validation process of the Small Aircraft Transportation Systems Higher Volume Operations (SATS HVO) concept and include an analysis of the predicted airport capacity using with different traffic conditions and system constraints under increasing levels of demand. Results show that SATS HVO procedures can dramatically increase capacity at non-towered, non-radar airports and that the concept offers the potential for increasing capacity of the overall air transportation system.

Consiglio, Maria C.↗

Crystal Growth Control

We present an innovative design of a vertical transparent multizone furnace which can operate in the temperature range of 25 C to 750 C and deliver thermal gradients of 2 C/cm to 45 C/cm for the commercial applications to crystal growth. The operation of the eight zone furnace is based on a self-tuning temperature control system with a DC power supply for optimal thermal stability. We show that the desired thermal profile over the entire length of the furnace consists of a functional combination of the fundamental thermal profiles for each individual zone obtained by setting the set-point temperature for that zone. The self-tuning system accounts for the zone to zone thermal interactions. The control system operates such that the thermal profile is maintained under thermal load, thus boundary conditions on crystal growth ampoules can be predetermined prior to crystal growth. Temperature profiles for the growth of crystals via directional solidification, vapor transport techniques, and multiple gradient applications are shown to be easily implemented. The unique feature of its transparency and ease of programming thermal profiles make the furnace useful for scientific and commercial applications for the determination of process parameters to optimize crystal growth conditions.

Duval, Walter M. B.↗

The Design of a Transparent Vertical Multizone Furnace: Application to Thermal Field Tuning and Crystal Growth

We present an innovative design of a vertical transparent multizone furnace which can operate in the temperature range of 25 C to 750 C and deliver thermal gradients of 2 C/cm to 45 C/cm for the commercial applications to crystal growth. The operation of the eight zone furnace is based on a self-tuning temperature control system with a DC power supply for optimal thermal stability. We show that the desired thermal profile over the entire length of the furnace consists of a functional combination of the fundamental thermal profiles for each individual zone obtained by setting the set-point temperature for that zone. The self-tuning system accounts for the zone to zone thermal interactions. The control system operates such that the thermal profile is maintained under thermal load, thus boundary conditions on crystal growth ampoules can be predetermined prior to crystal growth. Temperature profiles for the growth of crystals via directional solidification, vapor transport techniques, and multiple gradient applications are shown to be easily implemented. The unique feature of its transparency and ease of programming thermal profiles make the furnace useful in scientific and commercial applications for determining the optimized process parameters for crystal growth.

Duvual, Walter M. B.↗

Smart distribution systems

The increasing importance of system reliability and resilience is changing the way distribution systems are planned and operated. To achieve a distribution system self-healing against power outages, emerging technologies and devices, such as remote-controlled switches (RCSs) and smart meters, are being deployed. The higher level of automation is transforming traditional distribution systems into the smart distribution systems (SDSs) of the future. The availability of data and remote control capability in SDSs provides distribution operators with an opportunity to optimize system operation and control. In this paper, the development of SDSs and resulting benefits of enhanced system capabilities are discussed. A comprehensive survey is conducted on the state-of-the-art applications of RCSs and smart meters in SDSs. Specifically, a new method, called Temporal Causal Diagram (TCD), is used to incorporate outage notifications from smart meters for enhanced outage management. To fully utilize the fast operation of RCSs, the spanning tree search algorithm is used to develop service restoration strategies. Optimal placement of RCSs and the resulting enhancement of system reliability are discussed. Distribution system resilience with respect to extreme events is presented. Furthermore, test cases are used to demonstrate the benefit of SDSs. Active management of distributed generators (DGs) is introduced. Future research in a smart distribution environment is proposed.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Development of an Organic Rankine-Cycle power module for a small community solar thermal power experiment

An organic Rankine-cycle (ORC) power module was developed for use in a multimodule solar power plant to be built and operated in a small community. Many successful components and subsystems, including the reciever, power conversion subsystem, energy transport subsystem, and control subsystem, were tested. Tests were performed on a complete power module using a test bed concentrator in place of the proposed concentrator. All major single-module program functional objectives were met and the multimodule operation presented no apparent problems. The hermetically sealed, self-contained, ORC power conversion unit subsequently successfully completed a 300-hour endurance run with no evidence of wear or operating problems.

Kiceniuk, T.↗

AMO-EXPRESS-2.5: Crew Autonomy Onboard the International Space Station

NASA is committed to landing American astronauts, including the first woman and the next man, on the Moon by 2024. Currently, the crew cannot take on all functions performed by the ground today, so the future crews will need more automation to reduce the crew workload for future missions. Of significant importance for these missions is the balance between crew autonomy and vehicle automation. The Advanced Exploration Systems (AES) Autonomous Systems and Operations (ASO) Project has been investigating the ability to evaluate crew self-scheduling and activity monitoring for future space missions. The ASO project designed the Autonomous Mission and Operations- EXpedite the PRocessing of Experiments to Space Station Rack-2.5 (AMO-EXPRESS-2.5) payload to evaluate crew self-scheduling and activity monitoring. The AMO-EXPRESS-2.5 builds on the previous AMO-EXPRESS and AMO-EXPRESS-2.0 demonstrations on ISS. The AMO-EXPRESS-2.5 demonstration goals are to prove crew self-scheduling by planning through diagnosing systems expertise, failure detection, procedure recommendation and situational awareness. This paper will describe the development, test and execution results of the AMO-EXPRESS-2.5 demonstration, and will also outline the future planned development and operational efforts to enable autonomy for future deep space manned missions.

Brooke C. Allen↗

Mitigation of self-focusing in Thomson scattering experiments

A fundamental challenge associated with measuring Thomson scattering comes from the small scattering cross section associated with the interaction. Here, to improve photon statistics a powerful Thomson-scattering probe laser is required. Ponderomotive self-focusing limits the maximum power in the Thomson-scattering probe and was shown to limit the maximum achievable Thomson-scattering signal-to-noise ratio. Operating the laser at powers above the self-focusing critical power was shown to cause beam degradation, which reduced the amount of collected Thomson-scattered light. Using a phase plate was shown to improve laser beam propagation, and consequently improve the signal-to-noise ratio in the measured spectrum.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development and Implementation of Mechanistic Terry Turbine Models in RELAP-7 to Simulate RCIC Normal Operation Conditions

As part of the efforts to understand the unexpected “self-regulating” mode of the RCIC (Reactor Core Isolation Cooling) systems in Fukushima accidents and extend BWR RCIC and PWR AFW (Auxiliary Feed Water) operational range and flexibility, mechanistic models for the Terry turbine, based on Sandia’s original work [1], have been developed and implemented in the RELAP-7 code to simulate the RCIC system. In 2016, our effort has been focused on normal working conditions of the RCIC system. More complex off-design conditions will be pursued in later years when more data are available. In the Sandia model, the turbine stator inlet velocity is provided according to a reduced-order model which was obtained from a large number of CFD (computational fluid dynamics) simulations. In this work, we propose an alternative method, using an under-expanded jet model to obtain the velocity and thermodynamic conditions for the turbine stator inlet. The models include both an adiabatic expansion process inside the nozzle and a free expansion process outside of the nozzle to ambient pressure. The combined models are able to predict the steam mass flow rate and supersonic velocity to the Terry turbine bucket entrance, which are the necessary input information for the Terry turbine rotor model. The analytical models for the nozzle were validated with experimental data and benchmarked with CFD simulations. The analytical models generally agree well with the experimental data and CFD simulations. The analytical models are suitable for implementation into a reactor system analysis code or severe accident code as part of mechanistic and dynamical models to understand the RCIC behaviors. The newly developed nozzle models and modified turbine rotor model according to the Sandia’s original work have been implemented into RELAP-7, along with the original Sandia Terry turbine model. A new pump model has also been developed and implemented to couple with the Terry turbine model. An input model was developed to test the Terry turbine RCIC system, which generates reasonable results. Both the INL RCIC model and the Sandia RCIC model produce results matching major rated parameters such as the rotational speed, pump torque, and the turbine shaft work for the normal operation condition. The Sandia model is more sensitive to the turbine outlet pressure than the INL model. The next step will be further refining the Terry turbine models by including two-phase flow cases so that off-design conditions can be simulated. The pump model could also be enhanced with the use of the homologous curves.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Effect of electron-nuclear spin interactions for electron-spin qubits localized in InGaAs self-assembled quantum dots

The effect of electron-nuclear spin interactions on qubit operations is investigated for a qubit represented by the spin of an electron localized in an InGaAs self-assembled quantum dot. The localized electron wave function is evaluated within the atomistic tight-binding model. The electron Zeeman splitting induced by the electron-nuclear spin interaction is estimated in the presence of an inhomogeneous environment characterized by a random nuclear spin configuration, by the dot-size distribution, alloy disorder, and interface disorder. Due to these inhomogeneities, the electron Zeeman splitting varies from one qubit to another by the order of 10(-6), 10(-6), 10(-7), and 10(-9) eV, respectively. Such fluctuations cause errors in exchange operations due to the inequality of the Zeeman splitting between two qubits. However, the error can be made lower than the quantum error threshold if an exchange energy larger than 10(-4) eV is used for the operation. This result shows that the electron-nuclear spin interaction does not hinder quantum-dot based quantum computer architectures from being scalable even in the presence of inhomogeneous environments.

Whaley, K. Birgitta↗