SEARCH · Search NASA

Results for “SHEAR PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

DOE OSTI2025

AGC-4 Specimen Post-Irradiation Examination Data Interim Report

This interim report documents preliminary results of the post-irradiation examination material property testing from the fourth advanced graphite creep (AGC), AGC 4, capsule specimens. This is the fourth of a series of six irradiation test trains planned as part of the AGC experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphite grades to moderate dose levels (=7 dpa). The AGC 4 capsule was irradiated in the Idaho National Laboratory Advanced Test Reactor at a nominal temperature of 800°C and to a peak dose of 8 dpa. Half of the AGC-4 specimens were subjected to compressive stresses to induce irradiation creep. Post-irradiation testing and measurement results are reported with the exception of thermal testing, which is still in progress, and irradiation mechanical strength testing. Additionally, some specimens initially deemed too hot to be examined in the ART Graphite laboratory may still be measured. The data reported includes specimen dimensions for both stressed and unstressed specimens to establish the irradiation creep rates, mass and dimensional data necessary to derive density, elastic constants (Young?s modulus, shear modulus, and Poisson?s ratio) from ultrasonic time of flight velocity measurements, Young?s modulus from the fundamental frequency of vibration, and electrical resistivity. A more complete evaluation of trends in the material property changes, as well as irradiation-induced creep due to the irradiation environment and applied load on the specimens, will be discussed later in AGC 4 post-irradiation examination analysis reports.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Explaining the lack of power degradation of energy confinement in wide pedestal quiescent H-modes via transport modeling

Wide pedestal quiescent H (WPQH)-mode is an attractive scenario for future burning plasmas as they operate without ELMs. WPQH is characterized by formation of a wider and higher pedestal (than quiescent H-mode), and broadband fluctuations in the pedestal. Unlike conventional H-modes, where the energy confinement time reduces with increasing heating power, the WPQH plasmas reported in this paper do not show power degradation of the energy confinement. As the injected neutral beam power was increased, reduced core (ρ ≤ 0.45) transport calculated by transp, as well as increased core temperatures, pressure gradient and diamagnetic E × B shear rate were observed. The reduction in the heat transport and rapid decrease in the ion temperature gradient scale length suggest the formation of an ion internal transport barrier (ITB) that was accompanied by increased stored energy in the core. Quasilinear turbulent transport modeling using the trapped gyro Landau fluid (tglf) code was used to predict the ITB and its turbulence stability properties. By using profiles and equilibria produced by matching the transp transport fluxes with the tglf transport model within the tgyro transport solver, the energy confinement time captures the experimentally observed insensitivity to the increased PNBI. Linear stability analysis reveals that drift-wave instabilities in the core are stabilized by E × B shear, T i /T e ratio and Shafranov shift; the latter was found to have the strongest effect on the turbulence suppression at the highest heating level.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Anion and Cation Size Effects on Viscoelasticity and Ion Transport of Imine Vitrimer Electrolytes

Vitrimers are a subclass of covalent adaptable networks where bond exchange occurs without breaking, thereby offering polymer materials with enhanced mechanical strength, thermal stability, and reprocessability compared to conventional electrolytes. Despite recent progress, we lack a complete understanding of the role of ions in controlling the physical and chemical properties of vitrimers. In this work, we study how different salts affect the viscoelasticity, morphology, and ionic conductivity of imine vitrimers. Our results show that addition of salt decreases relaxation times at elevated temperatures due to the catalytic effect of the cations, with smaller cations leading to faster relaxation. However, the activation energy for terminal relaxation increases with smaller cation size. This apparent discrepancy is attributed to the complex interplay among bond exchange kinetics, chain diffusion, and salt dissociation. Anions act as plasticizers by reducing the shear modulus, except lithium bromide. Ionic conductivity increases with larger anions due to smaller salt dissociation energies, whereas the cation type has a minor impact as polymer segmental dynamics dominate ionic transport. Imine-based vitrimers are reprocessable and recyclable, maintaining original mechanical properties and ionic conductivity after recovery. Mixed salt vitrimers exhibited tunable viscoelasticity and ionic conductivity intermediate to the analogous pure salt systems. Altogether, this work highlights the role of salt in the dynamic and conductive properties of imine vitrimers.

Anions↗

DOE OSTI2020

Modeling of fluid injection-induced fault reactivation using coupled fluid flow and mechanical interface model

The present study is aimed at developing a numerical model to reproduce coupled hydro-mechanical processes associated with fault reactivation by fluid injection in low permeability rock, as part of the DECOVALEX-2019 project Task B. We proposed a modeling approach for simulating the processes using the TOUGH-FLAC simulator, and modeled a fault reactivation experiment conducted at Mont Terri Rock Laboratory in Switzerland. The first step of the study involved benchmark calculations considering a simplified fault plane and geometry. Fluid flow along a fault was modeled using elements of aperture-sized thickness on the basis of Darcy's law and the cubic law in TOUGH2, whereas the mechanical behavior of a single fault was represented by zero-thickness interface elements in FLAC3D upon which a slip and/or separation is allowed. A methodology to connect a TOUGH2 volume element to a FLAC3D interface element was developed for handling the hydro-mechanical interactions on the fault during fluid injection. Two different fault models for describing the evolutions of hydraulic aperture by elastic fracture opening and failure-induced aperture increase were considered in the benchmark calculations. In the coupling process, the changes in geometrical features and hydrological properties induced by mechanical deformation were continuously updated. The transient responses of the fault and host rock to stepwise pressurization were examined during the simulation. The hydro-mechanical behavior, including the injection flow rate, pressure distribution around the borehole, stress conditions, and displacements in normal and shear directions were monitored in the surrounding rock and along the fault. The results of benchmark calculations suggest that the developed model reasonably represents the hydro-mechanical behavior of a fault and the surrounding rock. This modeling approach was applied to the fault reactivation experiment of the Mont Terri Rock Laboratory. In this interpretive modeling, a parametric study was conducted to examine the effects of input parameters regarding in situ stress and fault properties on the hydro-mechanical responses of the fault to water injection. Then, an optimal parameter set to reproduce the field experiment results was chosen by trial-and-error. The injection flow rate and pressure response during fault reactivation closely matched those obtained at the site, which indicates the capability of the model to appropriately capture the progressive pathway evolution during fault reactivation tests at the site. Finally, the anchor displacements were overestimated by the model, but a fair agreement was obtained in terms of the order of magnitude and the variation tendency.

58 GEOSCIENCES↗

DOE OSTI2025

Fabrication of Piezoelectric Polymer and Metal–Organic Framework Composite Thin Films Using Solution Shearing

Polymer-metal–organic framework (polymer-MOF) composites have garnered significant interest as polymers can enhance the processability and industrial applicability of MOFs. Thin films of these composites are particularly attractive for applications in sensing, separations, and flexible electronics. Solution shearing, a meniscus-guided coating technique, has emerged as a scalable process for fabricating thin films of MOFs, and can produce large-area films within minutes. In this study, we utilized solution shearing to fabricate composite thin films of a MOF UiO-66 and a piezoelectric polymer poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)), investigating how polymer concentration during MOF synthesis and composite formation influences thin film properties, including crystallinity, surface coverage, and piezoelectric performance. Additionally, solid-state NMR spectroscopy was utilized to probe the interactions between P(VDF-TrFE) and UiO-66 in the composite. Evidence from solid-state NMR indicated polymer-MOF interactions, suggesting that the polymer strands are in close proximity to the UiO-66 pores, supporting a mixed surface coating and pore infiltration model. Furthermore, incorporating P(VDF-TrFE) enhanced the film’s areal coverage from 70% to 100%. While the thermal conductivity remained essentially unchanged, the composite film showed an improved piezoelectric effect. The composite with 91 wt % P(VDF-TrFE) exhibited the highest output voltage of 9.1 V and a sensitivity of 0.26 V/N under applied pressure. This work demonstrates the potential of solution shearing as a scalable technique for fabricating polymer-MOF composite thin films.

P(VDF-TrFE)↗

DOE OSTI2023

Cosmological constraints from the Subaru Hyper Suprime-Cam year 1 shear catalogue lensing convergence probability distribution function

Here we utilize the probability distribution function (PDF) of normalized convergence maps reconstructed from the Subaru Hyper Suprime-Cam (HSC) year 1 shear catalogue, in combination with the power spectrum, to measure the matter clustering amplitude S 8 = σ 8 $\sqrt {Ω_{m}/0.3}$. The large-scale structure’s statistical properties are incompletely described by the traditional two-point statistics, motivating our investigation of the PDF—a complementary higher-order statistic. By defining the PDF over the standard-deviation-normalized convergence map, we are able to isolate the non-Gaussian information. We use tailored simulations to compress the data vector and construct a likelihood approximation. We mitigate the impact of survey and astrophysical systematics with cuts on smoothing scales, redshift bins, and data vectors. We find S 8 = $0.860^{+0.066}_{–0.109}$ from the PDF alone and S 8 = 0.798$^{+0.029}_{–0.042}$ from the combination of the PDF and power spectrum (68% confidential level (CL)). The PDF improves the power-spectrum-only constraint by about 10%.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2020

The Terahertz Dynamics of an Aqueous Nanoparticle Suspension: An Inelastic X-ray Scattering Study

We used the high-resolution Inelastic X-ray Scattering beamline of the Advanced Photon Source at Argonne National Laboratory to measure the terahertz spectrum of pure water and a dilute aqueous suspension of 15 nm diameter spherical Au nanoparticles (Au-NPs). We observe that, despite their sparse volume concentration of about 0.5%, the immersed NPs strongly influence the collective molecular dynamics of the hosting liquid. We investigate this effect through a Bayesian inference analysis of the spectral lineshape, which elucidates how terahertz transport properties of water change upon Au-NP immersion. In particular, we observe a nearly complete disappearance of the longitudinal acoustic mode and a mildly decreased ability to support shear wave propagation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Process Robustness of Friction Stir Dovetailing of AA7099 to Steel with In Situ AA6061 Interlayer Linking

Rolled homogeneous armor (RHA) steel was joined to aluminum alloy AA7099-T7451 with an interlayer of AA6061-T651 by single-pass friction stir dovetailing (FSD). The evolution of the AA7099/AA6061 and AA6061/steel interfacial microstructures and mechanical properties of the joints were examined. The AA6061 interlayer prevented Zn migration from the AA7099 to the steel during FSD and inhibited formation of brittle, Zn-rich, Fe-Al intermetallic compounds within the joint. The flow of the dissimilar aluminum alloys at the interface was controlled with a partially threaded friction stir welding pin and a dovetail geometric configuration optimized in previous work. The process robustness was explored to establish parameter windows by elucidating parametric effects on the relationship between process conditions and the joint’s microstructure and mechanical properties. Ranges of process forge force (50–70 kN) and interface temperature (475°C–515°C) consistently yielded joints with adequate performance. The load-carrying capacity in lap shear tensile tests was 2025 ? 100 N/mm.

Friction Stir Dovetailing, FSW, AA7099, AA6061, Ro↗

DOE OSTI2024

Friction stir processing on a strontium modified, thin-wall, vacuum-assisted high-pressure die-cast Aural-5 alloy to improve tensile and fatigue performance

Here, this study explores the application of friction stir processing (FSP) to enhance the material properties of Sr-modified Aural-5 alloy, with a focus on improved tensile and fatigue properties. Aural-5 is a well-known vacuum-assisted high-pressure die-cast (HPDC) Al-Si7-Mg alloy used in the automotive industry to reduce vehicle weight, enhance fuel efficiency, and lower carbon emissions. This alloy modifies its material chemistry with Sr for fine fibrous networks of eutectic silicon and manganese (Mn) to reduce die soldering. It has significantly less iron (Fe) content resulting in the elimination of detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. The initial microstructure of as-received HPDC Aural-5 exhibits shrinkage porosity in the middle section, a dendritic microstructure with fibrous Al-Si eutectic colonies, a shear-band structure beneath the die-wall, large dendritic externally solidified crystals (ESCs), needle-shaped Mg 2 Si phase and significant second-phase particulates. Some of those microstructural features, such as porosity, ESCs, needle-shaped Mg 2 Si phase, and large second-phase particles, serve as initiation sites for cracks under mechanical loading, resulting in adverse effects on tensile properties, particularly ductility. FSP effectively transforms the microstructure into a wrought configuration with uniform particle distribution by eliminating porosity and disintegrating dendrites, eutectic colonies, ESCs, second-phase particles, and shear-band structures. FSP-driven microstructure modification enhances yield strength and tensile ductility by ~30% and ~35%, respectively. The fatigue life of the material in a bending mode configuration (stress ratio R = 0.1) after FSP exhibits enhancements ranging from 2.0 to 3.9 times that of the original HPDC Aural-5 alloy, depending on the applied stress level.

36 MATERIALS SCIENCE↗

DOE OSTI2019

The Effect of Calcium on the Cohesive Strength and Flexural Properties of Low-Methoxyl Pectin Biopolymers

Pectin binds the mesothelial glycocalyx of visceral organs, suggesting its potential role as a mesothelial sealant. To assess the mechanical properties of pectin films, we compared pectin films with a less than 50% degree of methyl esterification (low-methoxyl pectin, LMP) to films with greater than 50% methyl esterification (high-methoxyl pectin, HMP). LMP and HMP polymers were prepared by step-wise dissolution and high-shear mixing. Both LMP and HMP films demonstrated a comparable clear appearance. Fracture mechanics demonstrated that the LMP films had a lower burst strength than HMP films at a variety of calcium concentrations and hydration states. The water content also influenced the extensibility of the LMP films with increased extensibility (probe distance) with an increasing water content. Similar to the burst strength, the extensibility of the LMP films was less than that of HMP films. Flexural properties, demonstrated with the 3-point bend test, showed that the force required to displace the LMP films increased with an increased calcium concentration ( p < 0.01). Toughness, here reflecting deformability (ductility), was variable, but increased with an increased calcium concentration. Similarly, titrations of calcium concentrations demonstrated LMP films with a decreased cohesive strength and increased stiffness. We conclude that LMP films, particularly with the addition of calcium up to 10 mM concentrations, demonstrate lower strength and toughness than comparable HMP films. These physical properties suggest that HMP has superior physical properties to LMP for selected biomedical applications.

Biochemistry & Molecular Biology↗

DOE OSTI2025

3D polycatenated architected materials

Architected materials derive their properties from the geometric arrangement of their internal structural elements. Their designs rely on continuous networks of members to control the global mechanical behavior of the bulk. Here, in this study, we introduce a class of materials that consist of discrete concatenated rings or cage particles interlocked in three-dimensional networks, forming polycatenated architected materials (PAMs). We propose a general design framework that translates arbitrary crystalline networks into particle concatenations and geometries. In response to small external loads, PAMs behave like non-Newtonian fluids, showing both shear-thinning and shear-thickening responses, which can be controlled by their catenation topologies. At larger strains, PAMs behave like lattices and foams, with a nonlinear stress-strain relation. At microscale, we demonstrate that PAMs can change their shapes in response to applied electrostatic charges. The distinctive properties of PAMs pave the path for developing stimuli-responsive materials, energy-absorbing systems, and morphing architectures.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Upcycling of aluminum Twitch scrap via Shear Assisted Processing and Extrusion (ShAPE)

Aluminum is publicly perceived as recyclable, but mixed alloys and impurities in aluminum scrap require dilution via energy-intensive primary aluminum or downcycling to low-quality castings. In this study, cast billets of shredded aluminum scrap (Twitch) were blended with pre-consumer AA 6061, extruded into tubes via Shear Assisted Processing and Extrusion (ShAPE), and aged to T1 and T6 tempers. Microscopy reveals that ShAPE refined and distributed the deleterious AlFeSi phases. Furthermore, the Twitch extrusions had tensile properties comparable to AA 6061 yet without homogenizing or adding primary aluminum. Energy savings were 85% compared to conventional extrusion of primary aluminum alloys.

ShAPE↗

DOE OSTI2025

Viscosity-Controlled Thiol–Ene Reaction and Its Impact on Mechanical Response of Dynamic Networks

The impact of curing conditions on the final properties of thioester-thiol-based dynamic polymer networks was systematically investigated. Despite identical monomer and cross-linker compositions, networks synthesized in the absence of solvent exhibited significantly higher shear moduli and longer relaxation times compared to those cured in solvent. These differences arise from viscosity-controlled photoinitiated thiol–ene reactions, where reduced chain mobility under solvent-free conditions suppresses termination between two polymer radicals, leading to higher reaction conversion. Fourier Transform Infrared (FTIR) spectroscopy and solid-state NMR (ssNMR) spectroscopy confirmed a greater degree of “click” reaction completion in higher viscosity environments. Control experiments revealed that prolonged radical lifetimes and suppressed termination reactions under solvent-free curing conditions contribute to these variations. Here, this study highlights the crucial role of processing conditions in determining cross-link density and, consequently, the dynamic mechanical behavior of polymer networks. It demonstrates that, beyond polymer chemistry, dynamic cross-linker design, and phase separation, curing conditions serve as a key design parameter for tailoring material performance to specific applications.

polymers↗

DOE OSTI2026

Current ramp-up studies for NSTX-U in support of the development of non-inductive current ramp-up scenarios in STs

The Spherical Tokamak (ST) is a low-aspect-ratio tokamak projected to enable simultaneous operation at high normalized toroidal beta and high bootstrap current fraction. However, a compact ST reactor cannot be built with a full-sized solenoid. The remaining current required for sustained operation must be ramped up non-inductively. Sustained 100% non-inductive current drive at the MA level has not yet been demonstrated on an ST. Non-inductive current ramp-up is therefore a more challenging objective that the NSTX-U research program aims to address. In support of this development, free-boundary TRANSP simulations have been used to develop a current ramp-up scenario in which a significant fraction of the current is driven non-inductively by a combination of neutral-beam and bootstrap current drive. The resulting discharge has properties favorable for non-inductive current drive, such as a low normalized internal plasma inductance of approximately 0.45, a minimum safety factor exceeding 2, and a slightly reversed-shear q-profile. In these discharges, the plasma current ramps to 900 kA within 250 ms in an L-mode configuration, with varying electron density and density profiles. These discharges should be suitable for next-step NSTX-U experiments aimed at generating a robust L-mode fiducial scenario with low central solenoid flux consumption, which could be progressively improved as new NSTX-U experimental discharges are developed.

Raman, Roger [Univ. of Washington, Seattle, WA (Un↗

DOE OSTI2023

Solid Phase Processing at the Extreme

The effective application of high-flow-stress materials in the realm of Solid Phase Processing frequently necessitates operating at elevated temperatures and substantially high force. These rigorous processing conditions give rise to intricate predicaments concerning the durability of the tools and dies involved, as well as the efficient utilization of process energy. This project is centered on the investigation of the fundamental scientific aspects inherent to these challenges. We aim to delve into the details of how materials react when subjected to intense shear forces at die interfaces, determine the metallurgical interactions occurring at the interfaces with the dies, and investigate the consequences of extreme temperatures on material flow, microstructural evolution, and resultant properties.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Unraveling the implications of finite specimen size on the interpretation of dynamic experiments for polycrystalline aluminum through direct numerical simulations

Normal and Pressure-shear plate impact (NPI and PSPI) experiments are popular experimental techniques for studying the mean-field macroscopic behavior of polycrystalline metals under high-rate dynamic loading. However, since both configurations rely upon geometry for subjecting the specimen to high strain rates, these experiments often involve a limited specimen size. Moreover, because of the inherent heterogeneities present within polycrystalline metals, it is difficult to ascertain if the size of the specimen and/or regions where measurements are made are sufficiently large for making representative inferences about the mean-field macroscopic properties from single-point velocity measurements. In the present study, we quantify the expected measurement variability on observable point measurements in NPI and PSPI experiments by carrying out direct numerical simulations (DNS) of statistically representative polycrystalline microstructures subjected to dynamic compression and compression-shear loading. In particular, we consider the role of specific material heterogeneities (e.g. the grain-to-grain difference in size, crystallographic orientation) on dispersion in the normal and transverse particle velocity records and on local fluctuations in key state variables (e.g. velocity, accumulated plastic strain) by incorporating these effects directly into a representative synthetic microstructure geometry and crystalline description of pure polycrystalline aluminum. The form of the present study is a large parametric investigation, consisting of ten ensembles of one hundred simulations. Each of the thousand simulations reflects a randomly realized synthetic microstructure in one of five cases of decreasing average grain size for the two loading configurations. Our analysis of the DNS results demonstrates that for both of these experimental configurations, the grain size directly correlates with the coefficient of variation (CV) in simulated point measurements, showing a convergent decrease in CV to zero (i.e. particle velocity record approaches the mean-field value) with decreasing grain size. Remarkably, the magnitude of variations in the particle velocity record is shown to be largest where the deviatoric stresses are most significant. In the case of NPI, this occurs at the elastic and plastic wavefront, whereas, in the case of PSPI, the magnitude of fluctuations are approximately constant throughout the experimental window time. The reasoning for the scatter in particle velocity due to the heterogeneous microstructure is demonstrated to be dependent on the mechanisms for accommodating deformation and on the interaction of reflection waves generated at sites of heterogeneities occurring at the scale of grains. Lastly, we develop a power-law description for the magnitude of scattering versus characteristic length, which provides a statistical framework for assessing the required number of grains per characteristic specimen dimension for minimizing scatter within these two experimental configurations (NPI, PSPI).

36 MATERIALS SCIENCE↗

DOE OSTI2020

Viscous flow properties and hydrodynamic diameter of phenothiazine-based redox-active molecules in different supporting salt environments

We report viscous flow properties of a redox-active organic molecule, N-(2-(2-methoxyethoxy)ethyl)phenothiazine (MEEPT), a candidate for non-aqueous redox flow batteries, and two of its radical cation salts. A microfluidic viscometer enabled the use of small sample volumes in determining viscosity as a function of shear rate and concentration in the non-aqueous solvent, acetonitrile, both with and without supporting salts. All solutions tested show Newtonian behavior over shear rates of up to 30 000 s−1, which was rationalized by scaling arguments for the diffusion-based relaxation time of a single MEEPT molecule without aggregation. Neat MEEPT is flowable but with a large viscosity (412 mPa⋅s at room temperature), which is ∼1000 times larger than that of acetonitrile. MEEPT solutions in acetonitrile have low viscosities; at concentrations up to 0.5 M, the viscosity increases by less than a factor of two. From concentration-dependent viscosity measurements, molecular information was inferred from intrinsic viscosity (hydrodynamic diameter) and the Huggins coefficient (interactions). Model fit credibility was assessed using the Bayesian Information Criterion. It is found that the MEEPT and its charged cations are “flowable” and do not flocculate at concentrations up to 0.5 M. MEEPT has a hydrodynamic diameter of around 8.5 Å, which is almost insensitive to supporting salt and state of charge. This size is comparable to molecular dimensions of single molecules obtained from optimized structures using density functional theory calculations. The results suggest that MEEPT is a promising candidate for redox flow batteries in terms of its viscous flow properties.

Wang, Yilin (ORCID:0000000316102995)↗

DOE OSTI2023

High temperature elastic properties of sub-stoichiometric yttrium dihydrides

Yttrium hydrides are considered as candidate materials for neutron moderation applied in microreactors (akin transportable tiny nuclear reactors) owing to their superior thermal stability and hydrogen retention. The evolution of elastic properties of these materials at elevated temperatures, needed for predicting the thermomechanical response and performance of the moderator during in-service reactor conditions, however, is lacking. Here, we report the Young’s and shear elastic moduli of three stoichiometries of bulk yttrium hydride (YH x , x = 1.61, 1.82, and 1.84) from room temperature to 1000°C. In situ temperature-dependent measurements of the longitudinal and shear wave velocities were performed using a laser ultrasonic technique while heating the sample in a vacuum-pumped heating stage. The elastic moduli increased linearly with increasing hydrogen content and decreased by ~10% during heating from room temperature to 1000°C in the three YH x compositions. The linear relationship between the elastic moduli and the hydrogen content in yttrium hydride was verified by atomistic calculations based on density functional theory (DFT). The absence of abrupt changes in the temperature-dependent measurements of elastic modulus of the YH x samples suggested negligible loss of hydrogen at elevated temperatures. Excellent agreement was found between the measured and calculated dependence of the elastic moduli on the stoichiometry, thereby providing a new approach for investigating the effects of fabrication-induced parameters (such as porosity) on the elastic moduli. Furthermore, this study demonstrates the utility of the combined approach involving DFT-based atomistic calculations and measurements of the elastic moduli for the informative development of metal hydrides and can be used as a metric for novel moderator materials investigations for emerging microreactors and beyond.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗