Search NASA⌕ Search

SEARCH · Search NASA

Results for “STREAMLINE FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Aerodynamic heating on 3-D bodies including the effects of entropy-layer swallowing

A relatively simple method was developed previously (authors, 1973) for calculating laminar, transitional, and turbulent heating rates on three-dimensional bodies in hypersonic flows. This method was shown to yield reasonably accurate results for laminar heating on blunted circular and elliptical cones and an earlier version of the space shuttle vehicle. As the boundary layer along the surface grows, more and more of the inviscid-flow mass is entrained into the boundary layer, and the streamlines which passed through the nearly normal portion of the bow shock wave are 'swallowed' by the boundary layer. This phenomenon is often referred to as entropy-layer or streamline swallowing, and it can have a significant effect on the calculated heating rates. An approximate, yet simple, method for including the effects of entropy-layer swallowing in the heating-rate calculations is given.

Dejarnette, F. R.↗
NASA NTRS1985

Duct-Flow Analysis

Quasi-two-dimensional velocity distribution through annular duct calculated. Computer program ANDUCT developed for calculating velocity distribution along arbitrary line between inner and outer walls of annular duct with axisymmetric swirling flow. Velocity gradient equation used with assumed variation of meridional streamline curvature. ANDUCT written in FORTRAN IV for use on IBM 370/3033 computer.

Katsanis, T.↗
NASA NTRS1985

Large-eddy substitution via vortex cancellation for wall turbulence control

A system of co-rotating longitudinal vortices was used to introduce streamline (as opposed to wall) curvature into a turbulent wall flow. Two methods of vortex cancellation, unwinding and self-annihilation, were tested as a means of removing the vortices once they had processed most of the incoming turbulent boundary layer. Vortex unwinding, which uses vorticity of the opposite sign, was shown to be a viable method for cancelling the co-rotating vortices. Vortex self-annihilation, caused by interference effects resulting from a close initial spanwise vortex spacing, eliminated the vortices within 60 delta downstream. In each case, reductions in boundary layer entrainment were found once the vortices were cancelled.

Mcginley, C. B.↗
NASA NTRS1985

Vortex induced lift on a flat plate with a curved forward-facing flap

Free streamline solutions are obtained for two-dimensional inviscid incompressible flow past a flat plate with a forward-facing curved flap. It is shown that it is possible to shape the curved flap to make the adverse pressure gradient on top of the flap less severe than for a straight flap and thus increase the prospects of making the flow experimentally realizable.

Tanveer, S.↗
NASA NTRS1987

An investigation of the flow characteristics in the blade endwall corner region

Studies were undertaken to determine the structure of the flow in the blade end wall corner region simulated by attaching two uncambered airfoils on either side of a flat plate with a semicircular leading edge. Detailed measurements of the corner flow were obtained with conventional pressure probes, hot wire anemometry, and flow visualization. The mean velocity profiles and six components of the Reynolds stress tensor were obtained with an inclined single sensor hot wire probe whereas power spectra were obtained with a single sensor oriented normal to the flow. Three streamwise vortices were identified based on the surface streamlines, distortion of total pressure profiles, and variation of mean velocity components in the corner. A horseshoe vortex formed near the leading edge of the airfoil. Within a short distance downstream, a corner vortex was detected between the horseshoe vortex and the surfaces forming the corner. A third vortex was formed at the rear portion of the corner between the corner vortex and the surface of the flat plate. Turbulent shear stress and production of turbulence are negligibly small. A region of negative turbulent shear stress was also observed near the region of low turbulence intensity from the vicinity of the flat plate.

Hazarika, Birinchi K.↗
NASA NTRS1995

Exploratory flow visualization investigation of mast-mounted sights in presence of a rotor

A flow visualization investigation with a laser light sheet system was conducted on a 27-percent-scale AH-64 attack helicopter model fitted with two mast-mounted sights in the langley 14- by 22-foot subsonic tunnel. The investigation was conducted to identify aerodynamic phenomena that may have contributed to adverse vibration encountered during full-scale flight of the AH-64D apache/longbow helicopter with an asymmetric mast-mounted sight. Symmetric and asymmetric mast-mounted sights oriented at several skew angles were tested at simulated forward and rearward flight speeds of 30 and 45 knots. A laser light sheet system was used to visualize the flow in planes parallel to and perpendicular to the free-stream flow. Analysis of these flow visualization data identified frequencies of flow patterns in the wake shed from the sight, the streamline angle at the sight, and the location where the shed wake crossed the rotor plane. Differences in wake structure were observed between the sight configurations and various skew angles. Analysis of lateral light sheet plane data implied significant vortex structure in the wake of the asymmetric mast-mounted sight in the configuration that produced maximum in-flight vibration. The data showed no significant vortex structure in the wake of the asymmetric and symmetric configurations that produced no increase in in-flight adverse vibration.

Ghee, Terence A.↗
DOE OSTI2024

A streamline coordinate analysis of a turbulent boundary layer subject to pressure gradients and curvature on the windward side of a bump

Direct numerical simulation (DNS) of a turbulent boundary layer over the Gaussian (Boeing) bump is performed. This boundary layer exhibits a series of adverse and favourable pressure gradients and convex and concave curvature effects before separating. These effects on turbulent boundary layers are characterised and compared with a lower-Reynolds-number flow over the same geometry. The momentum budgets are analysed in the streamline-aligned coordinate system upstream of the separation region. These momentum budgets allow the simplification of equations to facilitate an integral analysis. Integral-analysis-based approximations for Reynolds stresses in the inner and outer regions of the boundary layer are also formulated. The shear and wall-normal Reynolds stress profiles normalised by these approximations exhibit a better collapse compared with friction velocity and Zagarola–Smits normalisations in the strong favourable pressure gradient region and in the mild adverse pressure region that precedes it in this flow. Simplification of these Reynolds stress approximations along with results from the DNS are used to obtain semi-empirical approximations that are able to provide stress closure in terms of wall solution fields for the turbulent boundary layer under consideration.

42 ENGINEERING↗
NASA NTRS1985

Sting-Mounted Flow Survey Apparatus

Flow survey instrumentation integral part of model support system. Drive motor, limit switches, and position transducer contained within streamlined housing and operable in near vacuum wing-tunnel environment. Sting-mounted system has advantages over conventional wall-mounted flow-field survey equipment, include more efficiently utilized run time, higher position accuracy, and fewer runs to map flow field.

Ashby, G. C., Jr.↗
NASA NTRS1988

Inverse Design Of Simple, Unbranched Ducts

Program calculates shape of duct to obtain desired flow field. Computer program, DIN3D1, developed for inverse design of simple, unbranched ducts. Inputs from user to computer program are velocity distributions for all surfaces making up duct. Includes upstream and downstream velocity fields and velocities along streamlines forming lateral boundaries of duct. Output of program contains duct geometry and complete flow field through duct. Written in FORTRAN IV.

Stanitz, J. D.↗
NASA NTRS1983

Formation of turbulence around flow singularities

The formation of turbulence around singular points of a flow such as stagnation points, tangential jumps of velocity, are analyzed. It is proved that turbulence is inevitably generated by the rear stagnation point, but cannot be generated by the nose stagnation point of a streamlined body. Special attention is paid to an evolution of turbulence induced by a tangential jump of velocity. A qualitative analysis of a turbulent flow between two rotating concentric cylinders and around a streamlined cylinder is given.

Zak, M.↗
NASA NTRS1979

Supercritical flow about a thick circular-arc airfoil

The supercritical flow about a biconvex circular-arc airfoil is being thoroughly documented at Ames Research Center in order to provide experimental test cases suitable for guiding and evaluating current and future computer codes. The effects of angle of attack, effects of leading and trailing-edge splitter plates, additional unsteady pressure fluctuation (buffeting) measurements and glow-field shadowgraphs, and application of an oil-film technique to display separated-wake streamlines were studied. Computed and measured pressure distributions for steady and unsteady flows, using a recent computer code representative of current methodology, are compared. It was found that the numerical solutions are often fundamentally incorrect in that only strong (shock-polar terminology) shocks are captured, whereas experimentally, both strong and weak shock waves appear.

Mcdevitt, J. B.↗
NASA NTRS1986

Performance studies on an axial flow compressor stage

A low-speed, medium loaded axial flow compressor stage is studied experimentally and theoretically. The flow compressor facility, composed of an inlet guide vane row, a rotor blade row, and a stator blade row, and the principles of the streamline curvature method (SCM) and the Douglas-Neumann cascade program are described. The radial distribution of the flow properties, the rotor blade static pressure distribution, and the lift coefficient and relative flow angle derived experimentally and theoretically are compared. It is determined that there is good correlation between the experimental flow properties and the SCM data, the Douglas-Neumann cascade program and experimental rotor blade static pressure data, and the experimental and theoretical lift coefficients only in the midspan region. Modifications to the SCM and the Douglas-Neumann cascade program in order to improve their accuracy are discussed.

Sitaram, N.↗
NASA NTRS1942

High-speed Tests of a Ducted Body with Various Air-outlet Openings

Test of a ducted body with Internal flow were made in the 8-foot high-speed wind tunnel for the purpose of studying the effects on external drag and an critical speed of the addition of efficient inlet and outlet openings to a basic streamline shape. Drag tests of a 13.6- inch-diameter streamline body of fineness ratio 6.14 were made at Mach numbers ranging from 0.20 to 0.75. The model was centrally mounted on a 9-percent-thick airfoil and was designed to have an efficient airfoil-body juncture and a high critical speed. An air inlet at the nose and various outlets at the tail were added: drag and internal-flow data were obtained over the given speed range. The critical speed of the ducted bodies was found to be as high as that of the streamline body. The external - drag with air flow through the body did not exceed the drag of the basic streamline shape. No appreciable variation in the efficiency of the diffuser section of the internal duct occurred throughout the Mach number range of the tests.

Becker, John V.↗
NASA NTRS1980

Analytical and experimental study of mean flow and turbulence characteristics inside the passages of an axial flow inducer

The inviscid and viscid effects existing within the passages of a three bladed axial flow inducer operating at a flow coefficient of 0.065 are investigated. The blade static pressure and blade limiting streamline angle distributions were determined and the three components of mean velocity, turbulence intensities, and turbulence stresses were measured at locations inside the inducer blade passage utilizing a rotating three sensor hotwire probe. Applicable equations were derived for the hotwire data reduction analysis and solved numerically to obtain the appropriate flow parameters. The three dimensional inviscid flow in the inducer was predicted by numerically solving the exact equations of motion, and the three dimensional viscid flow was predicted by incorporating the dominant viscous terms into the exact equations. The analytical results are compared with the experimental measurements and design values where appropriate. Radial velocities are found to be of the same order as axial velocities within the inducer passage, confirming the highly three dimensional characteristic of inducer flow. Total relative velocity distribution indicate a substantial velocity deficiency near the tip at mid-passage which expands significantly as the flow proceeds toward the inducer trailing edge. High turbulence intensities and turbulence stresses are concentrated within this core region. Considerable wake diffusion occurs immediately downstream of the inducer trailing edge to decay this loss core. Evidence of boundary layer interactions, blade blockage effects, radially inward flows, annulus wall effects, and backflows are all found to exist within the long, narrow passages of the inducer.

Gorton, C. A.↗
NASA NTRS1979

Developments in testing airfoil techniques at University of Southampton

The evolution in Europe of the flexible walled test section, as applied to two dimensional testing at low and transonic speeds, is traced from its beginnings at NPL, London, in the early 1940's, and is shown to lead logically to the latest version now nearing completion at Southampton University. The principal changes that have taken place are improvements in the methods of choosing wall contours such that they rapidly follow appropriate streamlines, and reductions in the depth of test sections. The latest transonic test section presently under assembly at Southampton has, as its principal new feature, the facility for the automation of wall streamlining with the aid of an on-line computer. The versatility of the flexible walled test section is emphasized by reference to the simulation of alternative flows including cascade, steady pitching in an infinite flowfield, and ground effect. Finally, sources of error in streamlining are identified, with methods for their alleviation.

Goodyer, M. J.↗
NASA NTRS1991

Effects of depth-variations in creep laws on the formation of plates in mantle dynamics

The influences of depth-varying rheologies on the structure of mantle convection and the near surface flow fields are studied. Upwelling flows crossing the upper-lower mantle boundary become considerably thinner and faster. Streamlines are concentrated near the surface and other platelike characteristics are enhanced by this type of rheological stratification in which the averaged effective viscosity of the upper mantle is about two orders of magnitude lower than that of the lower mantle. The presence of a lithosphere with a higher nonlinear dependence in the flow law further promotes platelike behavior. Platelike character of the top boundary-layer is encouraged by a decreasing depth-dependent viscosity in the non-Newtonian upper-mantle and by greater convective vigor.

Van Den Berg, Arie P.↗
NASA NTRS1986

The development of laser speckle velocimetry for the measurement of vortical flow fields

A new velocity measurement technique is described that provides the simultaneous visualization of a two-dimensional streamline pattern and the quantification of the velocity field. The main advantage of this technique is that the velocity field can be measured with sufficient accuracy and spatial resolution so that the vorticity field can be readily obtained. This technique is ideally suited for the study of unsteady vortical flows, which occur in rotorcraft and in high-angle-of-attack aerodynamics. The technique, some of the important parameters that affect its use, and some recent examples are described.

Smith, C. A.↗
NASA NTRS1947

The Streamline Pattern in the Vicinity of an Oblique Airfoil

A method for determining the streamwise flow pattern of a nonviscous incompressible fluid about an oblique airfoil from the corresponding flow pattern about the airfoil in normal position is presented and illustrated in two examples. The method can be extended to account approximately for compressibility effects by applying the Prandtl-Glauert correction factor to the flow pattern that is normal to the leading edge of the airfoil. The method is expected to be useful in determining the shape of a fuselage or nacelle having a minimum of interference with the flow over a swept-back wing.

Watkins, Charles E↗